# # CDROM driver configuration # menu "Old CD-ROM drivers (not SCSI, not IDE)" depends on ISA config CD_NO_IDESCSI bool "Support non-SCSI/IDE/ATAPI CDROM drives" ---help--- If you have a CD-ROM drive that is neither SCSI nor IDE/ATAPI, say Y here, otherwise N. Read the CD-ROM-HOWTO, available from . Note that the answer to this question doesn't directly affect the kernel: saying N will just cause the configurator to skip all the questions about these CD-ROM drives. If you are unsure what you have, say Y and find out whether you have one of the following drives. For each of these drivers, a file Documentation/cdrom/{driver_name} exists. Especially in cases where you do not know exactly which kind of drive you have you should read there. Most of these drivers use a file drivers/cdrom/{driver_name}.h where you can define your interface parameters and switch some internal goodies. To compile these CD-ROM drivers as a module, choose M instead of Y. If you want to use any of these CD-ROM drivers, you also have to answer Y or M to "ISO 9660 CD-ROM file system support" below (this answer will get "defaulted" for you if you enable any of the Linux CD-ROM drivers). config AZTCD tristate "Aztech/Orchid/Okano/Wearnes/TXC/CyDROM CDROM support" depends on CD_NO_IDESCSI ---help--- This is your driver if you have an Aztech CDA268-01A, Orchid CD-3110, Okano or Wearnes CDD110, Conrad TXC, or CyCD-ROM CR520 or CR540 CD-ROM drive. This driver -- just like all these CD-ROM drivers -- is NOT for CD-ROM drives with IDE/ATAPI interfaces, such as Aztech CDA269-031SE. Please read the file . If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM file system support" below, because that's the file system used on CD-ROMs. To compile this driver as a module, choose M here: the module will be called aztcd. config GSCD tristate "Goldstar R420 CDROM support" depends on CD_NO_IDESCSI ---help--- If this is your CD-ROM drive, say Y here. As described in the file , you might have to change a setting in the file before compiling the kernel. Please read the file . If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM file system support" below, because that's the file system used on CD-ROMs. To compile this driver as a module, choose M here: the module will be called gscd. config SBPCD tristate "Matsushita/Panasonic/Creative, Longshine, TEAC CDROM support" depends on CD_NO_IDESCSI && BROKEN_ON_SMP ---help--- This driver supports most of the drives which use the Panasonic or Sound Blaster interface. Please read the file . The Matsushita CR-521, CR-522, CR-523, CR-562, CR-563 drives (sometimes labeled "Creative"), the Creative Labs CD200, the Longshine LCS-7260, the "IBM External ISA CD-ROM" (in fact a CR-56x model), the TEAC CD-55A fall under this category. Some other "electrically compatible" drives (Vertos, Genoa, some Funai models) are currently not supported; for the Sanyo H94A drive currently a separate driver (asked later) is responsible. Most drives have a uniquely shaped faceplate, with a caddyless motorized drawer, but without external brand markings. The older CR-52x drives have a caddy and manual loading/eject, but still no external markings. The driver is able to do an extended auto-probing for interface addresses and drive types; this can help to find facts in cases you are not sure, but can consume some time during the boot process if none of the supported drives gets found. Once your drive got found, you should enter the reported parameters into and set "DISTRIBUTION 0" there. This driver can support up to four CD-ROM controller cards, and each card can support up to four CD-ROM drives; if you say Y here, you will be asked how many controller cards you have. If compiled as a module, only one controller card (but with up to four drives) is usable. If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM file system support" below, because that's the file system used on CD-ROMs. To compile this driver as a module, choose M here: the module will be called sbpcd. config MCD tristate "Mitsumi (standard) [no XA/Multisession] CDROM support" depends on CD_NO_IDESCSI ---help--- This is the older of the two drivers for the older Mitsumi models LU-005, FX-001 and FX-001D. This is not the right driver for the FX-001DE and the triple or quad speed models (all these are IDE/ATAPI models). Please also the file . With the old LU-005 model, the whole drive chassis slides out for cd insertion. The FX-xxx models use a motorized tray type mechanism. Note that this driver does not support XA or MultiSession CDs (PhotoCDs). There is a new driver (next question) which can do this. If you want that one, say N here. If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM file system support" below, because that's the file system used on CD-ROMs. To compile this driver as a module, choose M here: the module will be called mcd. config MCD_IRQ int "MCD IRQ" depends on MCD default "11" help This allows you to specify the default value of the IRQ used by the driver. This setting can be overridden by passing the "mcd=" parameter to the kernel at boot time (or at module load time if you said M to "Standard Mitsumi CD-ROM support"). config MCD_BASE hex "MCD I/O base" depends on MCD default "300" help This allows you to specify the default value of the I/O base address used by the driver. This setting can be overridden by passing the "mcd=" parameter to the kernel at boot time (or at module load time if you said M to "Standard Mitsumi CD-ROM support"). config MCDX tristate "Mitsumi [XA/MultiSession] CDROM support" depends on CD_NO_IDESCSI ---help--- Use this driver if you want to be able to read XA or MultiSession CDs (PhotoCDs) as well as ordinary CDs with your Mitsumi LU-005, FX-001 or FX-001D CD-ROM drive. In addition, this driver uses much less kernel memory than the old one, if that is a concern. This driver is able to support more than one drive, but each drive needs a separate interface card. Please read the file . If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM file system support" below, because that's the file system used on CD-ROMs. To compile this driver as a module, choose M here: the module will be called mcdx. config OPTCD tristate "Optics Storage DOLPHIN 8000AT CDROM support" depends on CD_NO_IDESCSI ---help--- This is the driver for the 'DOLPHIN' drive with a 34-pin Sony compatible interface. It also works with the Lasermate CR328A. If you have one of those, say Y. This driver does not work for the Optics Storage 8001 drive; use the IDE-ATAPI CD-ROM driver for that one. Please read the file . If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM file system support" below, because that's the file system used on CD-ROMs. To compile this driver as a module, choose M here: the module will be called optcd. config CM206 tristate "Philips/LMS CM206 CDROM support" depends on CD_NO_IDESCSI && BROKEN_ON_SMP ---help--- If you have a Philips/LMS CD-ROM drive cm206 in combination with a cm260 host adapter card, say Y here. Please also read the file . If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM file system support" below, because that's the file system used on CD-ROMs. To compile this driver as a module, choose M here: the module will be called cm206. config SJCD tristate "Sanyo CDR-H94A CDROM support" depends on CD_NO_IDESCSI help If this is your CD-ROM drive, say Y here and read the file . You should then also say Y or M to "ISO 9660 CD-ROM file system support" below, because that's the file system used on CD-ROMs. To compile this driver as a module, choose M here: the module will be called sjcd. config ISP16_CDI tristate "ISP16/MAD16/Mozart soft configurable cdrom interface support" depends on CD_NO_IDESCSI ---help--- These are sound cards with built-in cdrom interfaces using the OPTi 82C928 or 82C929 chips. Say Y here to have them detected and possibly configured at boot time. In addition, You'll have to say Y to a driver for the particular cdrom drive you have attached to the card. Read for details. To compile this driver as a module, choose M here: the module will be called isp16. config CDU31A tristate "Sony CDU31A/CDU33A CDROM support" depends on CD_NO_IDESCSI && BROKEN_ON_SMP ---help--- These CD-ROM drives have a spring-pop-out caddyless drawer, and a rectangular green LED centered beneath it. NOTE: these CD-ROM drives will not be auto detected by the kernel at boot time; you have to provide the interface address as an option to the kernel at boot time as described in or fill in your parameters into . Try "man bootparam" or see the documentation of your boot loader (lilo or loadlin) about how to pass options to the kernel. If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM file system support" below, because that's the file system used on CD-ROMs. To compile this driver as a module, choose M here: the module will be called cdu31a. config CDU535 tristate "Sony CDU535 CDROM support" depends on CD_NO_IDESCSI ---help--- This is the driver for the older Sony CDU-535 and CDU-531 CD-ROM drives. Please read the file . If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM file system support" below, because that's the file system used on CD-ROMs. To compile this driver as a module, choose M here: the module will be called sonycd535. endmenu