X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=INSTALL.Linux;h=8ae7aaca72b0d8004c3aa3e091ba08d50185e2c7;hb=refs%2Fheads%2Forig-parallel;hp=9115581771acef166ec91676946b6f298e912b2c;hpb=55aa00e0df2cacc67081d31b813328fb39ce3561;p=sliver-openvswitch.git diff --git a/INSTALL.Linux b/INSTALL.Linux index 911558177..8ae7aaca7 100644 --- a/INSTALL.Linux +++ b/INSTALL.Linux @@ -5,10 +5,9 @@ This document describes how to build and install Open vSwitch on a generic Linux host. If you want to install Open vSwitch on a Citrix XenServer version 5.5.0, see INSTALL.XenServer instead. -This version of Open vSwitch should be built manually with "configure" -and "make". Debian packaging for Open vSwitch is also included, but -they have not been recently tested, and so Debian packages are not a -recommended way to use this version of Open vSwitch. +This version of Open vSwitch may be built manually with "configure" +and "make", as described below. You may also build Debian packages by +running "dpkg-buildpackage". Build Requirements ------------------ @@ -24,8 +23,9 @@ you will need the following software: - libssl, from OpenSSL, is optional but recommended if you plan to connect the Open vSwitch to an OpenFlow controller. libssl is required to establish confidentiality and authenticity in the - connections from an Open vSwitch to an OpenFlow controller. To - enable, configure with --enable-ssl=yes. + connections from an Open vSwitch to an OpenFlow controller. If + libssl is installed, then Open vSwitch will automatically build + with support for it. To compile the kernel module, you must also install the following. If you cannot build or install the kernel module, you may use the @@ -48,6 +48,13 @@ INSTALL.userspace for more information. and NET_ACT_POLICE, either built-in or as modules. (NET_CLS_POLICE is obsolete and not needed.) + If GRE tunneling is being used it is recommended that the kernel + be compiled with IPv6 support (CONFIG_IPV6). This allows for + special handling (such as path MTU discovery) of IPv6 packets. + + To use Open vSwitch support for TAP devices, you must enable + CONFIG_TUN. + - To build a kernel module, you need the same version of GCC that was used to build that kernel. @@ -69,6 +76,17 @@ you will also need the following software: - Python 2.x, for x >= 4. +If you modify the ovsdbmonitor tool, then you will also need the +following: + + - pyuic4 from PyQt4 (http://www.riverbankcomputing.co.uk). + +If you modify the vswitchd database schema, then the E-R diagram in +the ovs-vswitchd.conf.db(5) manpage will be updated properly only if +you have the following: + + - "dot" from graphviz (http://www.graphviz.org/). + Installation Requirements ------------------------- @@ -91,6 +109,25 @@ following software: if it is installed in a different location, then some Open vSwitch log messages will not be as detailed. +You should ensure that /dev/urandom exists. To support TAP devices, +you must also ensure that /dev/net/tun exists. + +To run the ovsdmonitor tool, the machine must also have the following +software: + + - Python 2.x, for x >= 4. + + - Python Twisted Conch. + + - Python JSON. + + - PySide or PyQt4. + + - Python Zope interface module. + +(On Debian "lenny" the above can be installed with "apt-get install +python-json python-qt4 python-zopeinterface python-twisted-conch".) + Building and Installing Open vSwitch for Linux ============================================== @@ -155,24 +192,73 @@ Prerequisites section, follow the procedure below to build. To verify that the modules have been loaded, run "/sbin/lsmod" and check that openvswitch_mod is listed. + If the "insmod" operation fails, look at the last few kernel log + messages (e.g. with "dmesg | tail"): + + - The message "openvswitch_mod: exports duplicate symbol + br_should_route_hook (owned by bridge)" means that the bridge + module is loaded. Run "/sbin/rmmod bridge" to remove it. + + If "/sbin/rmmod bridge" fails with "ERROR: Module bridge does + not exist in /proc/modules", then the bridge is compiled into + the kernel, rather than as a module. Open vSwitch does not + support this configuration (see "Build Requirements", above). + + - The message "openvswitch_mod: exports duplicate symbol + dp_ioctl_hook (owned by ofdatapath)" means that the ofdatapath + module from the OpenFlow reference implementation is loaded. + Run "/sbin/rmmod ofdatapath" to remove it. (You might have to + delete any existing datapaths beforehand, using the "dpctl" + program included with the OpenFlow reference implementation. + "ovs-dpctl" will not work.) + + - Otherwise, the most likely problem is that Open vSwitch was + built for a kernel different from the one into which you are + trying to load it. Run "modinfo" on openvswitch_mod.ko and on + a module built for the running kernel, e.g.: + + % /sbin/modinfo openvswitch_mod.ko + % /sbin/modinfo /lib/modules/`uname -r`/kernel/net/bridge/bridge.ko + + Compare the "vermagic" lines output by the two commands. If + they differ, then Open vSwitch was built for the wrong kernel. + + - If you decide to report a bug or ask a question related to + module loading, please include the output from the "dmesg" and + "modinfo" commands mentioned above. + 7. Initialize the configuration database using ovsdb-tool, e.g.: - % ovsdb-tool create /etc/ovs-vswitchd.conf.db vswitchd/vswitch.ovsschema + % ovsdb-tool create /usr/local/etc/ovs-vswitchd.conf.db vswitchd/vswitch.ovsschema Startup ======= Before starting ovs-vswitchd itself, you need to start its -configuration database, ovsdb-server. Configure it to use the -database you created during step 7 of installation, above, and to -listen on a Unix domain socket, e.g.: - - % ovsdb-server /etc/ovs-vswitchd.conf.db --remote=punix:/var/run/ovsdb-server +configuration database, ovsdb-server. Each machine on which Open +vSwitch is installed should run its own copy of ovsdb-server. +Configure it to use the database you created during step 7 of +installation, above, to listen on a Unix domain socket, to connect to +any managers specified in the database itself, and to use the SSL +configuration in the database: + + % ovsdb-server /usr/local/etc/ovs-vswitchd.conf.db \ + --remote=punix:/usr/local/var/run/openvswitch/db.sock \ + --remote=db:Open_vSwitch,managers \ + --private-key=db:SSL,private_key \ + --certificate=db:SSL,certificate \ + --bootstrap-ca-cert=db:SSL,ca_cert + +Then initialize the database using ovs-vsctl. This is only +necessary the first time after you create the database with +ovsdb-tool (but running it at any time is harmless): + + % ovs-vsctl --no-wait init Then start the main Open vSwitch daemon, telling it to connect to the same Unix domain socket: - % ovs-vswitchd unix:/var/run/ovsdb-server + % ovs-vswitchd unix:/usr/local/var/run/openvswitch/db.sock Now you may use ovs-vsctl to set up bridges and other Open vSwitch features. For example, to create a bridge named br0 and add ports