X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=arch%2Farm%2Fmach-at91rm9200%2Fboard-ek.c;h=c4fdb415f20e435e3bf093adc4320b4e2b2ca272;hb=refs%2Fheads%2Fvserver;hp=868192351ddaf8dcde4af7d35100e6e1e42a9543;hpb=16c70f8c1b54b61c3b951b6fb220df250fe09b32;p=linux-2.6.git

diff --git a/arch/arm/mach-at91rm9200/board-ek.c b/arch/arm/mach-at91rm9200/board-ek.c
index 868192351..c4fdb415f 100644
--- a/arch/arm/mach-at91rm9200/board-ek.c
+++ b/arch/arm/mach-at91rm9200/board-ek.c
@@ -27,6 +27,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/spi/spi.h>
+#include <linux/mtd/physmap.h>
 
 #include <asm/hardware.h>
 #include <asm/setup.h>
@@ -37,20 +38,12 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <asm/hardware.h>
 #include <asm/arch/board.h>
 #include <asm/arch/gpio.h>
+#include <asm/arch/at91rm9200_mc.h>
 
 #include "generic.h"
 
-static void __init ek_init_irq(void)
-{
-	/* Initialize AIC controller */
-	at91rm9200_init_irq(NULL);
-
-	/* Set up the GPIO interrupts */
-	at91_gpio_irq_setup(BGA_GPIO_BANKS);
-}
 
 /*
  * Serial port configuration.
@@ -65,10 +58,8 @@ static struct at91_uart_config __initdata ek_uart_config = {
 
 static void __init ek_map_io(void)
 {
-	at91rm9200_map_io();
-
-	/* Initialize clocks: 18.432 MHz crystal */
-	at91_clock_init(18432000);
+	/* Initialize processor: 18.432 MHz crystal */
+	at91rm9200_initialize(18432000, AT91RM9200_BGA);
 
 	/* Setup the LEDs */
 	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
@@ -77,6 +68,11 @@ static void __init ek_map_io(void)
 	at91_init_serial(&ek_uart_config);
 }
 
+static void __init ek_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
 static struct at91_eth_data __initdata ek_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
@@ -93,7 +89,7 @@ static struct at91_udc_data __initdata ek_udc_data = {
 
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.det_pin	= AT91_PIN_PB27,
-	.is_b		= 0,
+	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
 };
@@ -113,6 +109,30 @@ static struct spi_board_info ek_spi_devices[] = {
 #endif
 };
 
+#define EK_FLASH_BASE	AT91_CHIPSELECT_0
+#define EK_FLASH_SIZE	0x200000
+
+static struct physmap_flash_data ek_flash_data = {
+	.width	= 2,
+};
+
+static struct resource ek_flash_resource = {
+	.start		= EK_FLASH_BASE,
+	.end		= EK_FLASH_BASE + EK_FLASH_SIZE - 1,
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device ek_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.dev		= {
+				.platform_data	= &ek_flash_data,
+			},
+	.resource	= &ek_flash_resource,
+	.num_resources	= 1,
+};
+
+
 static void __init ek_board_init(void)
 {
 	/* Serial */
@@ -136,6 +156,8 @@ static void __init ek_board_init(void)
 	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
 	at91_add_device_mmc(&ek_mmc_data);
 #endif
+	/* NOR Flash */
+	platform_device_register(&ek_flash);
 	/* VGA */
 //	ek_add_device_video();
 }