X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=arch%2Fcris%2FKconfig;h=ee716249b1162b7dcf9ed7dfc1be707a834686a0;hb=refs%2Fheads%2Fvserver;hp=9b0b719bf0c61345d1733eba2cb9e43d36c312d2;hpb=a8e794ca871505c8ea96cc102f4ad555c5231d7f;p=linux-2.6.git

diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig
index 9b0b719bf..ee716249b 100644
--- a/arch/cris/Kconfig
+++ b/arch/cris/Kconfig
@@ -9,37 +9,52 @@ config MMU
 	bool
 	default y
 
-config UID16
+config RWSEM_GENERIC_SPINLOCK
 	bool
 	default y
 
-config RWSEM_GENERIC_SPINLOCK
+config RWSEM_XCHGADD_ALGORITHM
+	bool
+
+config ARCH_HAS_ILOG2_U32
+	bool
+	default n
+
+config ARCH_HAS_ILOG2_U64
+	bool
+	default n
+
+config GENERIC_FIND_NEXT_BIT
 	bool
 	default y
 
-config RWSEM_XCHGADD_ALGORITHM
+config GENERIC_HWEIGHT
 	bool
+	default y
 
-source "init/Kconfig"
+config GENERIC_CALIBRATE_DELAY
+	bool
+	default y
 
+config IRQ_PER_CPU
+	bool
+	default y
 
-menu "General setup"
+config CRIS
+	bool
+	default y
 
-source "fs/Kconfig.binfmt"
+source "init/Kconfig"
 
-config ETRAX_KGDB
-	bool "Use kernel gdb debugger"
-	---help---
-	  The CRIS version of gdb can be used to remotely debug a running
-	  Linux kernel via the serial debug port.  Provided you have gdb-cris
-	  installed, run gdb-cris vmlinux, then type
+menu "General setup"
 
-	  (gdb) set remotebaud 115200           <- kgdb uses 115200 as default
-	  (gdb) target remote /dev/ttyS0        <- maybe you use another port
+source "fs/Kconfig.binfmt"
 
-	  This should connect you to your booted kernel (or boot it now if you
-	  didn't before).  The kernel halts when it boots, waiting for gdb if
-	  this option is turned on!
+config ETRAX_CMDLINE
+	string "Kernel command line"
+	default "root=/dev/mtdblock3"
+	help
+	  Pass additional commands to the kernel.
 
 config ETRAX_WATCHDOG
 	bool "Enable ETRAX watchdog"
@@ -59,7 +74,7 @@ config ETRAX_FAST_TIMER
        bool "Enable ETRAX fast timer API"
        help
          This options enables the API to a fast timer implementation using
-	 timer1 to get sub jiffie resolution timers (primarily one-shot 
+	 timer1 to get sub jiffie resolution timers (primarily one-shot
 	 timers).
 	 This is needed if CONFIG_ETRAX_SERIAL_FAST_TIMER is enabled.
 
@@ -75,8 +90,9 @@ config PREEMPT
 	  Say Y here if you are building a kernel for a desktop, embedded
 	  or real-time system.  Say N if you are unsure.
 
-endmenu
+source mm/Kconfig
 
+endmenu
 
 menu "Hardware setup"
 
@@ -99,22 +115,12 @@ config SVINTO_SIM
 	help
 	  Support the xsim ETRAX Simulator.
 
-config ETRAX200LX
-	bool "ETRAX-200LX-V32"
-	help
-	  Support CRIS V32.
-
 endchoice
 
 config ETRAX_ARCH_V10
        bool
        default y if ETRAX100LX || ETRAX100LX_V2
-       default n if !(ETRAX100LX || ETRAX100LX_V2) 
-
-config ETRAX_ARCH_V32
-       bool
-       default y if ETRAX200LX
-       default n if !(ETRAX200LX) 
+       default n if !(ETRAX100LX || ETRAX100LX_V2)
 
 config ETRAX_DRAM_SIZE
 	int "DRAM size (dec, in MB)"
@@ -128,35 +134,20 @@ config ETRAX_FLASH_BUSWIDTH
 	help
 	  Width in bytes of the Flash bus (1, 2 or 4). Is usually 2.
 
-config ETRAX_ROOT_DEVICE
-	string "Root device name"
-	default "/dev/mtdblock3"
-	help
-	  Specifies the device that should be mounted as root file system
-	  when booting from flash. The axisflashmap driver adds an additional
-	  mtd partition for the appended root file system image, so this option
-	  should normally be the mtdblock device for the partition after the
-	  last partition in the partition table.
-
-# duplicate choice configs are not yet supported, so the followinguse 
-# doesn't work:
-
 source arch/cris/arch-v10/Kconfig
 
 endmenu
 
+source "net/Kconfig"
+
 # bring in ETRAX built-in drivers
 menu "Drivers for built-in interfaces"
-
 source arch/cris/arch-v10/drivers/Kconfig
 
 endmenu
 
 source "drivers/base/Kconfig"
 
-# bring in Etrax built-in drivers
-source "arch/cris/drivers/Kconfig"
-
 # standard linux drivers
 source "drivers/mtd/Kconfig"
 
@@ -176,7 +167,7 @@ source "drivers/ieee1394/Kconfig"
 
 source "drivers/message/i2o/Kconfig"
 
-source "net/Kconfig"
+source "drivers/net/Kconfig"
 
 source "drivers/isdn/Kconfig"
 
@@ -200,19 +191,7 @@ source "sound/Kconfig"
 
 source "drivers/usb/Kconfig"
 
-
-menu "Kernel hacking"
-
-#bool 'Debug kmalloc/kfree' CONFIG_DEBUG_MALLOC
-config PROFILE
-	bool "Kernel profiling support"
-
-config PROFILE_SHIFT
-	int "Profile shift count"
-	depends on PROFILE
-	default "2"
-
-endmenu
+source "arch/cris/Kconfig.debug"
 
 source "kernel/vserver/Kconfig"
 
@@ -221,4 +200,3 @@ source "security/Kconfig"
 source "crypto/Kconfig"
 
 source "lib/Kconfig"
-