X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=arch%2Fmips%2Fcobalt%2Freset.c;h=753dfccae6fa090df4dfb5a6a1abcb53552c7050;hb=43bc926fffd92024b46cafaf7350d669ba9ca884;hp=084c8e59f42c9686b5a9c1132208a4ae597d93e3;hpb=cee37fe97739d85991964371c1f3a745c00dd236;p=linux-2.6.git

diff --git a/arch/mips/cobalt/reset.c b/arch/mips/cobalt/reset.c
index 084c8e59f..753dfccae 100644
--- a/arch/mips/cobalt/reset.c
+++ b/arch/mips/cobalt/reset.c
@@ -16,48 +16,45 @@
 #include <asm/reboot.h>
 #include <asm/system.h>
 #include <asm/mipsregs.h>
+#include <asm/mach-cobalt/cobalt.h>
 
-void cobalt_machine_restart(char *command)
+void cobalt_machine_halt(void)
 {
-	*(volatile char *)0xbc000000 = 0x0f;
+	int state, last, diff;
+	unsigned long mark;
 
 	/*
-	 * Ouch, we're still alive ... This time we take the silver bullet ...
-	 * ... and find that we leave the hardware in a state in which the
-	 * kernel in the flush locks up somewhen during of after the PCI
-	 * detection stuff.
+	 * turn off bar on Qube, flash power off LED on RaQ (0.5Hz)
+	 *
+	 * restart if ENTER and SELECT are pressed
 	 */
-	set_c0_status(ST0_BEV | ST0_ERL);
-	change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED);
-	flush_cache_all();
-	write_c0_wired(0);
-	__asm__ __volatile__(
-		"jr\t%0"
-		:
-		: "r" (0xbfc00000));
-}
 
-extern int led_state;
-#define kLED            0xBC000000
-#define LEDSet(x)       (*(volatile unsigned char *) kLED) = (( unsigned char)x)
+	last = COBALT_KEY_PORT;
 
-void cobalt_machine_halt(void)
-{
-	int mark;
+	for (state = 0;;) {
+
+		state ^= COBALT_LED_POWER_OFF;
+		COBALT_LED_PORT = state;
+
+		diff = COBALT_KEY_PORT ^ last;
+		last ^= diff;
 
-	/* Blink our cute? little LED (number 3)... */
-	while (1) {
-		led_state = led_state | ( 1 << 3 );
-		LEDSet(led_state);
-		mark = jiffies;
-		while (jiffies<(mark+HZ));
-		led_state = led_state & ~( 1 << 3 );
-		LEDSet(led_state);
-		mark = jiffies;
-		while (jiffies<(mark+HZ));
+		if((diff & (COBALT_KEY_ENTER | COBALT_KEY_SELECT)) && !(~last & (COBALT_KEY_ENTER | COBALT_KEY_SELECT)))
+			COBALT_LED_PORT = COBALT_LED_RESET;
+
+		for (mark = jiffies; jiffies - mark < HZ;)
+			;
 	}
 }
 
+void cobalt_machine_restart(char *command)
+{
+	COBALT_LED_PORT = COBALT_LED_RESET;
+
+	/* we should never get here */
+	cobalt_machine_halt();
+}
+
 /*
  * This triggers the luser mode device driver for the power switch ;-)
  */