X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=arch%2Fppc%2F8xx_io%2Fenet.c;h=ece6a9fbe09bf1d8fda9c45552bbef95ff43d750;hb=43bc926fffd92024b46cafaf7350d669ba9ca884;hp=f720d2a4ca6dad9e4a09bda3cb4290a298d1730c;hpb=6a77f38946aaee1cd85eeec6cf4229b204c15071;p=linux-2.6.git

diff --git a/arch/ppc/8xx_io/enet.c b/arch/ppc/8xx_io/enet.c
index f720d2a4c..ece6a9fbe 100644
--- a/arch/ppc/8xx_io/enet.c
+++ b/arch/ppc/8xx_io/enet.c
@@ -657,7 +657,7 @@ static int __init scc_enet_init(void)
 
 	cp = cpmp;	/* Get pointer to Communication Processor */
 
-	immap = (immap_t *)(mfspr(IMMR) & 0xFFFF0000);	/* and to internal registers */
+	immap = (immap_t *)(mfspr(SPRN_IMMR) & 0xFFFF0000);	/* and to internal registers */
 
 	bd = (bd_t *)__res;
 
@@ -714,16 +714,24 @@ static int __init scc_enet_init(void)
 	immap->im_ioport.iop_pcdat &= ~PC_ENET_LBK;	/* Disable Loopback */
 #endif	/* PC_ENET_LBK */
 
-	/* Configure port C pins to enable CLSN and RENA.
+#ifdef PE_ENET_TCLK
+	/* Configure port E for TCLK and RCLK.
 	*/
-	immap->im_ioport.iop_pcpar &= ~(PC_ENET_CLSN | PC_ENET_RENA);
-	immap->im_ioport.iop_pcdir &= ~(PC_ENET_CLSN | PC_ENET_RENA);
-	immap->im_ioport.iop_pcso  |=  (PC_ENET_CLSN | PC_ENET_RENA);
-
+	cp->cp_pepar |=  (PE_ENET_TCLK | PE_ENET_RCLK);
+	cp->cp_pedir &= ~(PE_ENET_TCLK | PE_ENET_RCLK);
+	cp->cp_peso  &= ~(PE_ENET_TCLK | PE_ENET_RCLK);
+#else
 	/* Configure port A for TCLK and RCLK.
 	*/
 	immap->im_ioport.iop_papar |=  (PA_ENET_TCLK | PA_ENET_RCLK);
 	immap->im_ioport.iop_padir &= ~(PA_ENET_TCLK | PA_ENET_RCLK);
+#endif
+
+	/* Configure port C pins to enable CLSN and RENA.
+	*/
+	immap->im_ioport.iop_pcpar &= ~(PC_ENET_CLSN | PC_ENET_RENA);
+	immap->im_ioport.iop_pcdir &= ~(PC_ENET_CLSN | PC_ENET_RENA);
+	immap->im_ioport.iop_pcso  |=  (PC_ENET_CLSN | PC_ENET_RENA);
 
 	/* Configure Serial Interface clock routing.
 	 * First, clear all SCC bits to zero, then set the ones we want.
@@ -896,14 +904,18 @@ static int __init scc_enet_init(void)
 	/* It is now OK to enable the Ethernet transmitter.
 	 * Unfortunately, there are board implementation differences here.
 	 */
-#if   (!defined (PB_ENET_TENA) &&  defined (PC_ENET_TENA))
+#if   (!defined (PB_ENET_TENA) &&  defined (PC_ENET_TENA) && !defined (PE_ENET_TENA))
 	immap->im_ioport.iop_pcpar |=  PC_ENET_TENA;
 	immap->im_ioport.iop_pcdir &= ~PC_ENET_TENA;
-#elif ( defined (PB_ENET_TENA) && !defined (PC_ENET_TENA))
+#elif ( defined (PB_ENET_TENA) && !defined (PC_ENET_TENA) && !defined (PE_ENET_TENA))
 	cp->cp_pbpar |= PB_ENET_TENA;
 	cp->cp_pbdir |= PB_ENET_TENA;
+#elif ( !defined (PB_ENET_TENA) && !defined (PC_ENET_TENA) && defined (PE_ENET_TENA))
+	cp->cp_pepar |=  PE_ENET_TENA;
+	cp->cp_pedir &= ~PE_ENET_TENA;
+	cp->cp_peso  |=  PE_ENET_TENA;
 #else
-#error Configuration Error: define exactly ONE of PB_ENET_TENA, PC_ENET_TENA
+#error Configuration Error: define exactly ONE of PB_ENET_TENA, PC_ENET_TENA, PE_ENET_TENA
 #endif
 
 #if defined(CONFIG_RPXLITE) || defined(CONFIG_RPXCLASSIC)
@@ -936,6 +948,29 @@ static int __init scc_enet_init(void)
 	*((volatile uint *)BCSR1) &= ~BCSR1_ETHEN;
 #endif
 
+#ifdef CONFIG_MPC885ADS
+
+	/* Deassert PHY reset and enable the PHY.
+	 */
+	{
+		volatile uint __iomem *bcsr = ioremap(BCSR_ADDR, BCSR_SIZE);
+		uint tmp;
+
+		tmp = in_be32(bcsr + 1 /* BCSR1 */);
+		tmp |= BCSR1_ETHEN;
+		out_be32(bcsr + 1, tmp);
+		tmp = in_be32(bcsr + 4 /* BCSR4 */);
+		tmp |= BCSR4_ETH10_RST;
+		out_be32(bcsr + 4, tmp);
+		iounmap(bcsr);
+	}
+
+	/* On MPC885ADS SCC ethernet PHY defaults to the full duplex mode
+	 * upon reset. SCC is set to half duplex by default. So this
+	 * inconsistency should be better fixed by the software.
+	 */
+#endif
+
 	dev->base_addr = (unsigned long)ep;
 #if 0
 	dev->name = "CPM_ENET";
@@ -969,3 +1004,4 @@ static int __init scc_enet_init(void)
 }
 
 module_init(scc_enet_init);
+