X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=drivers%2Fide%2FKconfig;h=3f828052f8d27d176603a8e1e0aa3a20956d6464;hb=refs%2Fheads%2Fvserver;hp=d633081fa4c58123bc8769e7439af651039cb415;hpb=76828883507a47dae78837ab5dec5a5b4513c667;p=linux-2.6.git

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index d633081fa..3f828052f 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -4,6 +4,8 @@
 # Andre Hedrick <andre@linux-ide.org>
 #
 
+if BLOCK
+
 menu "ATA/ATAPI/MFM/RLL support"
 
 config IDE
@@ -54,7 +56,7 @@ if IDE
 
 config IDE_MAX_HWIFS
 	int "Max IDE interfaces"
-	depends on ALPHA || SUPERH || IA64
+	depends on ALPHA || SUPERH || IA64 || EMBEDDED
 	default 4
 	help
 	  This is the maximum number of IDE hardware interfaces that will
@@ -387,14 +389,6 @@ config BLK_DEV_RZ1000
 	  Linux. This may slow disk throughput by a few percent, but at least
 	  things will operate 100% reliably.
 
-config BLK_DEV_SL82C105
-	tristate "Winbond SL82c105 support"
-	depends on PCI && (PPC || ARM) && BLK_DEV_IDEPCI
-	help
-	  If you have a Winbond SL82c105 IDE controller, say Y here to enable
-	  special configuration for this chip. This is common on various CHRP
-	  motherboards, but could be used elsewhere. If in doubt, say Y.
-
 config BLK_DEV_IDEDMA_PCI
 	bool "Generic PCI bus-master DMA support"
 	depends on PCI && BLK_DEV_IDEPCI
@@ -592,6 +586,12 @@ config BLK_DEV_HPT366
 	  ide-probe at boot. It is reported to support DVD II drives, by the
 	  manufacturer.
 
+config BLK_DEV_JMICRON
+	tristate "JMicron JMB36x support"
+	help
+	  Basic support for the JMicron ATA controllers. For full support
+	  use the libata drivers.
+
 config BLK_DEV_SC1200
 	tristate "National SCx200 chipset support"
 	help
@@ -606,15 +606,6 @@ config BLK_DEV_PIIX
 	  the kernel to change PIO, DMA and UDMA speeds and to configure
 	  the chip to optimum performance.
 
-config BLK_DEV_IT8172
-	bool "IT8172 IDE support"
-	depends on (MIPS_ITE8172 || MIPS_IVR)
-	help
-	  Say Y here to support the on-board IDE controller on the Integrated
-	  Technology Express, Inc. ITE8172 SBC.  Vendor page at
-	  <http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the
-	  board at <http://www.mvista.com/partners/semiconductor/ite.html>.
-
 config BLK_DEV_IT821X
 	tristate "IT821X IDE support"
 	help
@@ -682,6 +673,7 @@ config BLK_DEV_SVWKS
 config BLK_DEV_SGIIOC4
 	tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support"
 	depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4
+	select IDEPCI_SHARE_IRQ
 	help
 	  This driver adds PIO & MultiMode DMA-2 support for the SGI IOC4
 	  chipset, which has one channel and can support two devices.
@@ -712,6 +704,14 @@ config BLK_DEV_SIS5513
 
 	  Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>.
 
+config BLK_DEV_SL82C105
+	tristate "Winbond SL82c105 support"
+	depends on (PPC || ARM)
+	help
+	  If you have a Winbond SL82c105 IDE controller, say Y here to enable
+	  special configuration for this chip. This is common on various CHRP
+	  motherboards, but could be used elsewhere. If in doubt, say Y.
+
 config BLK_DEV_SLC90E66
 	tristate "SLC90E66 chipset support"
 	help
@@ -773,13 +773,6 @@ config BLK_DEV_IDEDMA_PMAC
 	  to transfer data to and from memory.  Saying Y is safe and improves
 	  performance.
 
-config BLK_DEV_IDE_PMAC_BLINK
-	bool "Blink laptop LED on drive activity"
-	depends on BLK_DEV_IDE_PMAC && ADB_PMU
-	help
-	  This option enables the use of the sleep LED as a hard drive
-	  activity LED.
-
 config BLK_DEV_IDE_SWARM
 	tristate "IDE for Sibyte evaluation boards"
 	depends on SIBYTE_SB1xxx_SOC
@@ -803,7 +796,7 @@ endchoice
 config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
        int "Maximum transfer size (KB) per request (up to 128)"
        default "128"
-       depends BLK_DEV_IDE_AU1XXX
+       depends on BLK_DEV_IDE_AU1XXX
 
 config IDE_ARM
 	def_bool ARM && (ARCH_A5K || ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
@@ -1088,3 +1081,5 @@ config BLK_DEV_HD
 endif
 
 endmenu
+
+endif