X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=drivers%2Finput%2Fkeyboard%2FKconfig;h=049f2f544e75e94a9d40aee991df4cf8d45510f4;hb=refs%2Fheads%2Fvserver;hp=3b0ac3b43c541f04ede9fb7503964c5f6b32ee61;hpb=76828883507a47dae78837ab5dec5a5b4513c667;p=linux-2.6.git

diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
index 3b0ac3b43..049f2f544 100644
--- a/drivers/input/keyboard/Kconfig
+++ b/drivers/input/keyboard/Kconfig
@@ -13,7 +13,7 @@ menuconfig INPUT_KEYBOARD
 if INPUT_KEYBOARD
 
 config KEYBOARD_ATKBD
-	tristate "AT keyboard" if !X86_PC
+	tristate "AT keyboard" if EMBEDDED || !X86_PC
 	default y
 	select SERIO
 	select SERIO_LIBPS2
@@ -121,6 +121,17 @@ config KEYBOARD_NEWTON
 	  To compile this driver as a module, choose M here: the
 	  module will be called newtonkbd.
 
+config KEYBOARD_STOWAWAY
+	tristate "Stowaway keyboard"
+	select SERIO
+	help
+	  Say Y here if you have a Stowaway keyboard on a serial port.
+	  Stowaway compatible keyboards like Dicota Input-PDA keyboard
+	  are also supported by this driver.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called stowaway.
+
 config KEYBOARD_CORGI
 	tristate "Corgi keyboard"
 	depends on PXA_SHARPSL
@@ -155,7 +166,7 @@ config KEYBOARD_AMIGA
 
 config KEYBOARD_HIL_OLD
 	tristate "HP HIL keyboard support (simple driver)"
-	depends on GSC
+	depends on GSC || HP300
 	default y
 	help
 	  The "Human Interface Loop" is a older, 8-channel USB-like
@@ -166,13 +177,13 @@ config KEYBOARD_HIL_OLD
 	  However, it has been thoroughly tested and is stable.
 
 	  If you want full HIL support including support for multiple
-	  keyboards, mices and tablets, you have to enable the
+	  keyboards, mice, and tablets, you have to enable the
 	  "HP System Device Controller i8042 Support" in the input/serio
 	  submenu.
 
 config KEYBOARD_HIL
 	tristate "HP HIL keyboard support"
-	depends on GSC
+	depends on GSC || HP300
 	default y
 	select HP_SDC
 	select HIL_MLC
@@ -183,4 +194,24 @@ config KEYBOARD_HIL
 	  This driver implements support for HIL-keyboards attached
 	  to your machine, so normally you should say Y here.
 
+config KEYBOARD_OMAP
+	tristate "TI OMAP keypad support"
+	depends on (ARCH_OMAP1 || ARCH_OMAP2)
+	help
+	  Say Y here if you want to use the OMAP keypad.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called omap-keypad.
+
+config KEYBOARD_AAED2000
+	tristate "AAED-2000 keyboard"
+	depends on MACH_AAED2000
+	default y
+	help
+	  Say Y here to enable the keyboard on the Agilent AAED-2000
+	  development board.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called aaed2000_kbd.
+
 endif