X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=drivers%2Fmtd%2Fmaps%2FKconfig;fp=drivers%2Fmtd%2Fmaps%2FKconfig;h=64d1b6a6c920b9cfab28c3395134b09e257f3174;hb=16c70f8c1b54b61c3b951b6fb220df250fe09b32;hp=7abd7fee0ddaa669b64f167e587c6e3a8ab7aacf;hpb=4e76c8a9fa413ccc09d3f7f664183dcce3555d57;p=linux-2.6.git

diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
index 7abd7fee0..64d1b6a6c 100644
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -13,13 +13,13 @@ config MTD_COMPLEX_MAPPINGS
 
 config MTD_PHYSMAP
 	tristate "CFI Flash device in physical memory map"
-	depends on MTD_CFI
+	depends on MTD_CFI || MTD_JEDECPROBE || MTD_ROM
 	help
-	  This provides a 'mapping' driver which allows the CFI probe and
-	  command set driver code to communicate with flash chips which
-	  are mapped physically into the CPU's memory. You will need to
-	  configure the physical address and size of the flash chips on
-	  your particular board as well as the bus width, either statically
+	  This provides a 'mapping' driver which allows the NOR Flash and
+	  ROM driver code to communicate with chips which are mapped
+	  physically into the CPU's memory. You will need to configure
+	  the physical address and size of the flash chips on your
+	  particular board as well as the bus width, either statically
 	  with config options or at run-time.
 
 config MTD_PHYSMAP_START
@@ -37,7 +37,7 @@ config MTD_PHYSMAP_START
 config MTD_PHYSMAP_LEN
 	hex "Physical length of flash mapping"
 	depends on MTD_PHYSMAP
-	default "0x4000000"
+	default "0"
 	help
 	  This is the total length of the mapping of the flash chips on
 	  your particular board. If there is space, or aliases, in the
@@ -78,7 +78,7 @@ config MTD_PNC2000
 
 config MTD_SC520CDP
 	tristate "CFI Flash device mapped on AMD SC520 CDP"
-	depends on X86 && MTD_CFI
+	depends on X86 && MTD_CFI && MTD_CONCAT
 	help
 	  The SC520 CDP board has two banks of CFI-compliant chips and one
 	  Dual-in-line JEDEC chip. This 'mapping' driver supports that
@@ -109,7 +109,7 @@ config MTD_TS5500
 	  mtd1 allows you to reprogram your BIOS. BE VERY CAREFUL.
 
 	  Note that jumper 3 ("Write Enable Drive A") must be set
-	  otherwise detection won't succeeed.
+	  otherwise detection won't succeed.
 
 config MTD_SBC_GXX
 	tristate "CFI Flash device mapped on Arcom SBC-GXx boards"
@@ -200,8 +200,8 @@ config MTD_TSUNAMI
 	  Support for the flash chip on Tsunami TIG bus.
 
 config MTD_LASAT
-	tristate "Flash chips on LASAT board"
-	depends on LASAT
+	tristate "LASAT flash device"
+	depends on LASAT && MTD_CFI
 	help
 	  Support for the flash chips on the Lasat 100 and 200 boards.
 
@@ -212,7 +212,7 @@ config MTD_NETtel
 	  Support for flash chips on NETtel/SecureEdge/SnapGear boards.
 
 config MTD_ALCHEMY
-	tristate '  AMD Alchemy Pb1xxx/Db1xxx/RDK MTD support'
+	tristate "AMD Alchemy Pb1xxx/Db1xxx/RDK MTD support"
 	depends on SOC_AU1X00
 	help
 	  Flash memory access on AMD Alchemy Pb/Db/RDK Reference Boards
@@ -561,7 +561,6 @@ config MTD_PCMCIA
 config MTD_PCMCIA_ANONYMOUS
 	bool "Use PCMCIA MTD drivers for anonymous PCMCIA cards"
 	depends on MTD_PCMCIA
-	default N
 	help
 	  If this option is enabled, PCMCIA cards which do not report
 	  anything about themselves are assumed to be MTD cards.