X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=drivers%2Fnet%2FKconfig;h=922ca22a02e8972d4380726263a38b2b3c5024d6;hb=a2f44b27303a5353859d77a3e96a1d3f33f56ab7;hp=a2bd8119270e02d35801757e82c4b3a6c311dbf5;hpb=92ade515e123147bbf29ad4456d01a8963d36b71;p=linux-2.6.git diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index a2bd81192..922ca22a0 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -24,12 +24,15 @@ config NETDEVICES If unsure, say Y. +# All the following symbols are dependent on NETDEVICES - do not repeat +# that for each of the symbols. +if NETDEVICES config IFB tristate "Intermediate Functional Block support" depends on NET_CLS_ACT ---help--- - This is an intermidiate driver that allows sharing of + This is an intermediate driver that allows sharing of resources. To compile this driver as a module, choose M here: the module will be called ifb. If you want to use more than one ifb @@ -185,6 +188,17 @@ config MII or internal device. It is safe to say Y or M here even if your ethernet card lack MII. +config MACB + tristate "Atmel MACB support" + depends on NET_ETHERNET && AVR32 + select MII + help + The Atmel MACB ethernet interface is found on many AT32 and AT91 + parts. Say Y to include support for the MACB chip. + + To compile this driver as a module, choose M here: the module + will be called macb. + source "drivers/net/arm/Kconfig" config MACE @@ -438,12 +452,6 @@ config MIPS_JAZZ_SONIC This is the driver for the onboard card of MIPS Magnum 4000, Acer PICA, Olivetti M700-10 and a few other identical OEM systems. -config MIPS_GT96100ETH - bool "MIPS GT96100 Ethernet support" - depends on NET_ETHERNET && MIPS_GT96100 - help - Say Y here to support the Ethernet subsystem on your GT96100 card. - config MIPS_AU1X00_ENET bool "MIPS AU1000 Ethernet support" depends on NET_ETHERNET && SOC_AU1X00 @@ -489,7 +497,7 @@ config SGI_IOC3_ETH_HW_TX_CSUM config MIPS_SIM_NET tristate "MIPS simulator Network device (EXPERIMENTAL)" - depends on NETDEVICES && MIPS_SIM && EXPERIMENTAL + depends on MIPS_SIM && EXPERIMENTAL help The MIPSNET device is a simple Ethernet network device which is emulated by the MIPS Simulator. @@ -1300,6 +1308,23 @@ config PCNET32 . The module will be called pcnet32. +config PCNET32_NAPI + bool "Use RX polling (NAPI) (EXPERIMENTAL)" + depends on PCNET32 && EXPERIMENTAL + help + NAPI is a new driver API designed to reduce CPU and interrupt load + when the driver is receiving lots of packets from the card. It is + still somewhat experimental and thus not yet enabled by default. + + If your estimated Rx load is 10kpps or more, or if the card will be + deployed on potentially unfriendly networks (e.g. in a firewall), + then say Y here. + + See for more + information. + + If in doubt, say N. + config AMD8111_ETH tristate "AMD 8111 (new PCI lance) support" depends on NET_PCI && PCI @@ -1411,6 +1436,22 @@ config FORCEDETH . The module will be called forcedeth. +config FORCEDETH_NAPI + bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)" + depends on FORCEDETH && EXPERIMENTAL + help + NAPI is a new driver API designed to reduce CPU and interrupt load + when the driver is receiving lots of packets from the card. It is + still somewhat experimental and thus not yet enabled by default. + + If your estimated Rx load is 10kpps or more, or if the card will be + deployed on potentially unfriendly networks (e.g. in a firewall), + then say Y here. + + See for more + information. + + If in doubt, say N. config CS89x0 tristate "CS89x0 support" @@ -1739,8 +1780,8 @@ config VIA_RHINE_NAPI information. config LAN_SAA9730 - bool "Philips SAA9730 Ethernet support (EXPERIMENTAL)" - depends on NET_PCI && EXPERIMENTAL && MIPS + bool "Philips SAA9730 Ethernet support" + depends on NET_PCI && PCI && MIPS_ATLAS help The SAA9730 is a combined multimedia and peripheral controller used in thin clients, Internet access terminals, and diskless @@ -2082,16 +2123,16 @@ config SKGE config SKY2 tristate "SysKonnect Yukon2 support (EXPERIMENTAL)" - depends on PCI && EXPERIMENTAL + depends on PCI select CRC32 ---help--- - This driver supports Gigabit Ethernet adapters based on the the + This driver supports Gigabit Ethernet adapters based on the Marvell Yukon 2 chipset: Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/ 88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21 - This driver does not support the original Yukon chipset: a seperate - driver, skge, is provided for Yukon-based adapters. + There is companion driver for the older Marvell Yukon and + Genesis based adapters: skge. To compile this driver as a module, choose M here: the module will be called sky2. This is recommended. @@ -2106,7 +2147,7 @@ config SK98LIN This driver supports the original Yukon chipset. A cleaner driver is also available (skge) which seems to work better than this one. - This driver does not support the newer Yukon2 chipset. A seperate + This driver does not support the newer Yukon2 chipset. A separate driver, sky2, is provided to support Yukon2-based adapters. The following adapters are supported by this driver: @@ -2213,6 +2254,35 @@ config BNX2 To compile this driver as a module, choose M here: the module will be called bnx2. This is recommended. +config BCM5700 + tristate "Broadcom 57xx support" + depends on PCI + ---help--- + This driver supports the Broadcom (HP NC10xx/67xx/77xx/150x/320x/325x) Gigabit + family adapters. Specifically, it supports: + HP NC1020 Gigabit Server Adapter + HP NC6770 Gigabit Server Adapter + HP NC7760 Gigabit Server Adapter + HP Embedded NC7761 Gigabit Server Adapter + HP NC7770 Gigabit Server Adapter + HP NC7771 Gigabit Server Adapter + HP NC7780 Gigabit Server Adapter + HP NC7781 Gigabit Server Adapter + HP NC7782 Embedded Gigabit Server + HP ProLiant NC150T PCI 4-Port Gigabit Combo Switch Adapter + HP NC320i Integrated Gigabit Server Adapter + HP NC325i Integrated Dual Port PCI Express Gigabit Server Adapter + HP NC320T Gigabit Server Adapter + HP NC324i Integrated Dual Port PCI Express Gigabit Server Adapter + HP NC326i Integrated Dual Port PCI Express Gigabit Server Adapter + + The source for this driver was obtained from + + + To compile this driver as a module, choose M here and read + . The module + will be called bcm5700. + config SPIDER_NET tristate "Spider Gigabit Ethernet driver" depends on PCI && PPC_IBM_CELL_BLADE @@ -2221,6 +2291,14 @@ config SPIDER_NET This driver supports the Gigabit Ethernet chips present on the Cell Processor-Based Blades from IBM. +config TSI108_ETH + tristate "Tundra TSI108 gigabit Ethernet support" + depends on TSI108_BRIDGE + help + This driver supports Tundra TSI108 gigabit Ethernet ports. + To compile this driver as a module, choose M here: the module + will be called tsi108_eth. + config GIANFAR tristate "Gianfar Ethernet" depends on 85xx || 83xx || PPC_86xx @@ -2258,11 +2336,11 @@ config UGETH_TX_ON_DEMOND config UGETH_HAS_GIGA bool - depends on UCC_GETH && MPC836x + depends on UCC_GETH && PPC_MPC836x config MV643XX_ETH tristate "MV-643XX Ethernet support" - depends on MOMENCO_OCELOT_C || MOMENCO_JAGUAR_ATX || MV64360 || MOMENCO_OCELOT_3 || PPC_MULTIPLATFORM + depends on MOMENCO_OCELOT_C || MOMENCO_JAGUAR_ATX || MV64360 || MOMENCO_OCELOT_3 || (PPC_MULTIPLATFORM && PPC32) select MII help This driver supports the gigabit Ethernet on the Marvell MV643XX @@ -2290,6 +2368,15 @@ config MV643XX_ETH_2 This enables support for Port 2 of the Marvell MV643XX Gigabit Ethernet. +config QLA3XXX + tristate "QLogic QLA3XXX Network Driver Support" + depends on PCI + help + This driver supports QLogic ISP3XXX gigabit Ethernet cards. + + To compile this driver as a module, choose M here: the module + will be called qla3xxx. + endmenu # @@ -2302,10 +2389,11 @@ menu "Ethernet (10000 Mbit)" config CHELSIO_T1 tristate "Chelsio 10Gb Ethernet support" depends on PCI + select CRC32 help - This driver supports Chelsio N110 and N210 models 10Gb Ethernet - cards. More information about adapter features and performance - tuning is in . + This driver supports Chelsio gigabit and 10-gigabit + Ethernet cards. More information about adapter features and + performance tuning is in . For general information about Chelsio and our products, visit our website at . @@ -2318,6 +2406,30 @@ config CHELSIO_T1 To compile this driver as a module, choose M here: the module will be called cxgb. +config CHELSIO_T1_1G + bool "Chelsio gigabit Ethernet support" + depends on CHELSIO_T1 + help + Enables support for Chelsio's gigabit Ethernet PCI cards. If you + are using only 10G cards say 'N' here. + +config CHELSIO_T1_NAPI + bool "Use Rx Polling (NAPI)" + depends on CHELSIO_T1 + default y + help + NAPI is a driver API designed to reduce CPU and interrupt load + when the driver is receiving lots of packets from the card. + +config EHEA + tristate "eHEA Ethernet support" + depends on IBMEBUS + ---help--- + This driver supports the IBM pSeries eHEA ethernet adapter. + + To compile the driver as a module, choose M here. The module + will be called ehea. + config IXGB tristate "Intel(R) PRO/10GbE support" depends on PCI @@ -2399,6 +2511,12 @@ config MYRI10GE . The module will be called myri10ge. +config NETXEN_NIC + tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC" + depends on PCI + help + This enables the support for NetXen's Gigabit Ethernet card. + endmenu source "drivers/net/tokenring/Kconfig" @@ -2419,7 +2537,7 @@ config ISERIES_VETH config RIONET tristate "RapidIO Ethernet over messaging driver support" - depends on NETDEVICES && RAPIDIO + depends on RAPIDIO config RIONET_TX_SIZE int "Number of outbound queue entries" @@ -2550,6 +2668,7 @@ config PLIP config PPP tristate "PPP (point-to-point protocol) support" + select SLHC ---help--- PPP (Point to Point Protocol) is a newer and better SLIP. It serves the same purpose: sending Internet traffic over telephone (and other @@ -2668,6 +2787,7 @@ config PPP_MPPE select CRYPTO select CRYPTO_SHA1 select CRYPTO_ARC4 + select CRYPTO_ECB ---help--- Support for the MPPE Encryption protocol, as employed by the Microsoft Point-to-Point Tunneling Protocol. @@ -2730,6 +2850,7 @@ config SLIP config SLIP_COMPRESSED bool "CSLIP compressed headers" depends on SLIP + select SLHC ---help--- This protocol is faster than SLIP because it uses compression on the TCP/IP headers (not on the data itself), but it has to be supported @@ -2742,6 +2863,12 @@ config SLIP_COMPRESSED , explains how to configure CSLIP. This won't enlarge your kernel. +config SLHC + tristate + help + This option enables Van Jacobsen serial line header compression + routines. + config SLIP_SMART bool "Keepalive and linefill" depends on SLIP @@ -2776,7 +2903,7 @@ config NET_FC "SCSI generic support". config SHAPER - tristate "Traffic Shaper (EXPERIMENTAL)" + tristate "Traffic Shaper (OBSOLETE)" depends on EXPERIMENTAL ---help--- The traffic shaper is a virtual network device that allows you to @@ -2785,9 +2912,9 @@ config SHAPER these virtual devices. See for more information. - An alternative to this traffic shaper is the experimental - Class-Based Queuing (CBQ) scheduling support which you get if you - say Y to "QoS and/or fair queuing" above. + An alternative to this traffic shaper are traffic schedulers which + you'll get if you say Y to "QoS and/or fair queuing" in + "Networking options". To compile this driver as a module, choose M here: the module will be called shaper. If unsure, say N. @@ -2799,6 +2926,8 @@ config NETCONSOLE If you want to log kernel messages over the network, enable this. See for details. +endif #NETDEVICES + config NETPOLL def_bool NETCONSOLE