X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=drivers%2Fnet%2Fchelsio%2Fmy3126.c;fp=drivers%2Fnet%2Fchelsio%2Fmy3126.c;h=82fed1dd5005525b1fdbc44d78db6de46e33d6f6;hb=76828883507a47dae78837ab5dec5a5b4513c667;hp=0000000000000000000000000000000000000000;hpb=64ba3f394c830ec48a1c31b53dcae312c56f1604;p=linux-2.6.git

diff --git a/drivers/net/chelsio/my3126.c b/drivers/net/chelsio/my3126.c
new file mode 100644
index 000000000..82fed1dd5
--- /dev/null
+++ b/drivers/net/chelsio/my3126.c
@@ -0,0 +1,207 @@
+/* $Date: 2005/11/12 02:13:49 $ $RCSfile: my3126.c,v $ $Revision: 1.15 $ */
+#include "cphy.h"
+#include "elmer0.h"
+#include "suni1x10gexp_regs.h"
+
+/* Port Reset */
+static int my3126_reset(struct cphy *cphy, int wait)
+{
+	/*
+	 * This can be done through registers.  It is not required since
+	 * a full chip reset is used.
+	 */
+	return (0);
+}
+
+static int my3126_interrupt_enable(struct cphy *cphy)
+{
+	schedule_delayed_work(&cphy->phy_update, HZ/30);
+	t1_tpi_read(cphy->adapter, A_ELMER0_GPO, &cphy->elmer_gpo);
+	return (0);
+}
+
+static int my3126_interrupt_disable(struct cphy *cphy)
+{
+	cancel_rearming_delayed_work(&cphy->phy_update);
+	return (0);
+}
+
+static int my3126_interrupt_clear(struct cphy *cphy)
+{
+	return (0);
+}
+
+#define OFFSET(REG_ADDR)    (REG_ADDR << 2)
+
+static int my3126_interrupt_handler(struct cphy *cphy)
+{
+	u32 val;
+	u16 val16;
+	u16 status;
+	u32 act_count;
+	adapter_t *adapter;
+	adapter = cphy->adapter;
+
+	if (cphy->count == 50) {
+		mdio_read(cphy, 0x1, 0x1, &val);
+		val16 = (u16) val;
+		status = cphy->bmsr ^ val16;
+
+		if (status & BMSR_LSTATUS)
+			t1_link_changed(adapter, 0);
+		cphy->bmsr = val16;
+
+		/* We have only enabled link change interrupts so it
+		   must be that
+		 */
+		cphy->count = 0;
+	}
+
+	t1_tpi_write(adapter, OFFSET(SUNI1x10GEXP_REG_MSTAT_CONTROL),
+		SUNI1x10GEXP_BITMSK_MSTAT_SNAP);
+	t1_tpi_read(adapter,
+		OFFSET(SUNI1x10GEXP_REG_MSTAT_COUNTER_1_LOW), &act_count);
+	t1_tpi_read(adapter,
+		OFFSET(SUNI1x10GEXP_REG_MSTAT_COUNTER_33_LOW), &val);
+	act_count += val;
+
+	/* Populate elmer_gpo with the register value */
+	t1_tpi_read(adapter, A_ELMER0_GPO, &val);
+	cphy->elmer_gpo = val;
+
+	if ( (val & (1 << 8)) || (val & (1 << 19)) ||
+	     (cphy->act_count == act_count) || cphy->act_on ) {
+		if (is_T2(adapter))
+			val |= (1 << 9);
+		else if (t1_is_T1B(adapter))
+			val |= (1 << 20);
+		cphy->act_on = 0;
+	} else {
+		if (is_T2(adapter))
+			val &= ~(1 << 9);
+		else if (t1_is_T1B(adapter))
+			val &= ~(1 << 20);
+		cphy->act_on = 1;
+	}
+
+	t1_tpi_write(adapter, A_ELMER0_GPO, val);
+
+	cphy->elmer_gpo = val;
+	cphy->act_count = act_count;
+	cphy->count++;
+
+	return cphy_cause_link_change;
+}
+
+static void my3216_poll(struct work_struct *work)
+{
+	struct cphy *cphy = container_of(work, struct cphy, phy_update.work);
+
+	my3126_interrupt_handler(cphy);
+}
+
+static int my3126_set_loopback(struct cphy *cphy, int on)
+{
+	return (0);
+}
+
+/* To check the activity LED */
+static int my3126_get_link_status(struct cphy *cphy,
+			int *link_ok, int *speed, int *duplex, int *fc)
+{
+	u32 val;
+	u16 val16;
+	adapter_t *adapter;
+
+	adapter = cphy->adapter;
+	mdio_read(cphy, 0x1, 0x1, &val);
+	val16 = (u16) val;
+
+	/* Populate elmer_gpo with the register value */
+	t1_tpi_read(adapter, A_ELMER0_GPO, &val);
+	cphy->elmer_gpo = val;
+
+	*link_ok = (val16 & BMSR_LSTATUS);
+
+	if (*link_ok) {
+		/* Turn on the LED. */
+		if (is_T2(adapter))
+			 val &= ~(1 << 8);
+		else if (t1_is_T1B(adapter))
+			 val &= ~(1 << 19);
+	} else {
+		/* Turn off the LED. */
+		if (is_T2(adapter))
+			 val |= (1 << 8);
+		else if (t1_is_T1B(adapter))
+			 val |= (1 << 19);
+	}
+
+	t1_tpi_write(adapter, A_ELMER0_GPO, val);
+	cphy->elmer_gpo = val;
+	*speed = SPEED_10000;
+	*duplex = DUPLEX_FULL;
+
+	/* need to add flow control */
+	if (fc)
+		*fc = PAUSE_RX | PAUSE_TX;
+
+	return (0);
+}
+
+static void my3126_destroy(struct cphy *cphy)
+{
+	kfree(cphy);
+}
+
+static struct cphy_ops my3126_ops = {
+	.destroy		= my3126_destroy,
+	.reset			= my3126_reset,
+	.interrupt_enable	= my3126_interrupt_enable,
+	.interrupt_disable	= my3126_interrupt_disable,
+	.interrupt_clear	= my3126_interrupt_clear,
+	.interrupt_handler	= my3126_interrupt_handler,
+	.get_link_status	= my3126_get_link_status,
+	.set_loopback		= my3126_set_loopback,
+};
+
+static struct cphy *my3126_phy_create(adapter_t *adapter,
+			int phy_addr, struct mdio_ops *mdio_ops)
+{
+	struct cphy *cphy = kzalloc(sizeof (*cphy), GFP_KERNEL);
+
+	if (!cphy)
+		return NULL;
+
+	cphy_init(cphy, adapter, phy_addr, &my3126_ops, mdio_ops);
+	INIT_DELAYED_WORK(&cphy->phy_update, my3216_poll);
+	cphy->bmsr = 0;
+
+	return (cphy);
+}
+
+/* Chip Reset */
+static int my3126_phy_reset(adapter_t * adapter)
+{
+	u32 val;
+
+	t1_tpi_read(adapter, A_ELMER0_GPO, &val);
+	val &= ~4;
+	t1_tpi_write(adapter, A_ELMER0_GPO, val);
+	msleep(100);
+
+	t1_tpi_write(adapter, A_ELMER0_GPO, val | 4);
+	msleep(1000);
+
+	/* Now lets enable the Laser. Delay 100us */
+	t1_tpi_read(adapter, A_ELMER0_GPO, &val);
+	val |= 0x8000;
+	t1_tpi_write(adapter, A_ELMER0_GPO, val);
+	udelay(100);
+	return (0);
+}
+
+struct gphy t1_my3126_ops = {
+	my3126_phy_create,
+	my3126_phy_reset
+};