X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=drivers%2Fnet%2Fe1000%2Fe1000_hw.h;h=f1219dd9dbac2b41a727db0d90b29bf67f092f4f;hb=987b0145d94eecf292d8b301228356f44611ab7c;hp=c01e5d2e549b31e71aeb32b8b9c16861350cb12d;hpb=f7ed79d23a47594e7834d66a8f14449796d4f3e6;p=linux-2.6.git diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h index c01e5d2e5..f1219dd9d 100644 --- a/drivers/net/e1000/e1000_hw.h +++ b/drivers/net/e1000/e1000_hw.h @@ -60,7 +60,6 @@ typedef enum { e1000_82571, e1000_82572, e1000_82573, - e1000_80003es2lan, e1000_num_macs } e1000_mac_type; @@ -139,13 +138,6 @@ typedef enum { e1000_cable_length_undefined = 0xFF } e1000_cable_length; -typedef enum { - e1000_gg_cable_length_60 = 0, - e1000_gg_cable_length_60_115 = 1, - e1000_gg_cable_length_115_150 = 2, - e1000_gg_cable_length_150 = 4 -} e1000_gg_cable_length; - typedef enum { e1000_igp_cable_length_10 = 10, e1000_igp_cable_length_20 = 20, @@ -216,7 +208,6 @@ typedef enum { e1000_phy_m88 = 0, e1000_phy_igp, e1000_phy_igp_2, - e1000_phy_gg82563, e1000_phy_undefined = 0xFF } e1000_phy_type; @@ -290,7 +281,6 @@ typedef enum { #define E1000_ERR_MASTER_REQUESTS_PENDING 10 #define E1000_ERR_HOST_INTERFACE_COMMAND 11 #define E1000_BLK_PHY_RESET 12 -#define E1000_ERR_SWFW_SYNC 13 /* Function prototypes */ /* Initialization */ @@ -314,8 +304,6 @@ int32_t e1000_phy_hw_reset(struct e1000_hw *hw); int32_t e1000_phy_reset(struct e1000_hw *hw); int32_t e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info); int32_t e1000_validate_mdi_setting(struct e1000_hw *hw); -int32_t e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data); -int32_t e1000_write_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data); /* EEPROM Functions */ int32_t e1000_init_eeprom_params(struct e1000_hw *hw); @@ -462,13 +450,10 @@ int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); #define E1000_DEV_ID_82572EI_COPPER 0x107D #define E1000_DEV_ID_82572EI_FIBER 0x107E #define E1000_DEV_ID_82572EI_SERDES 0x107F -#define E1000_DEV_ID_82572EI 0x10B9 #define E1000_DEV_ID_82573E 0x108B #define E1000_DEV_ID_82573E_IAMT 0x108C #define E1000_DEV_ID_82573L 0x109A #define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5 -#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096 -#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098 #define NODE_ADDRESS_SIZE 6 @@ -865,7 +850,6 @@ struct e1000_ffvt_entry { #define E1000_TXCW 0x00178 /* TX Configuration Word - RW */ #define E1000_RXCW 0x00180 /* RX Configuration Word - RO */ #define E1000_TCTL 0x00400 /* TX Control - RW */ -#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */ #define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */ #define E1000_TBT 0x00448 /* TX Burst Timer - RW */ #define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */ @@ -1012,11 +996,6 @@ struct e1000_ffvt_entry { #define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */ #define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */ -#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */ -#define E1000_MDPHYA 0x0003C /* PHY address - RW */ -#define E1000_MANC2H 0x05860 /* Managment Control To Host - RW */ -#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */ - #define E1000_GCR 0x05B00 /* PCI-Ex Control */ #define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */ #define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */ @@ -1086,7 +1065,6 @@ struct e1000_ffvt_entry { #define E1000_82542_RXCW E1000_RXCW #define E1000_82542_MTA 0x00200 #define E1000_82542_TCTL E1000_TCTL -#define E1000_82542_TCTL_EXT E1000_TCTL_EXT #define E1000_82542_TIPG E1000_TIPG #define E1000_82542_TDBAL 0x00420 #define E1000_82542_TDBAH 0x00424 @@ -1234,8 +1212,6 @@ struct e1000_ffvt_entry { #define E1000_82542_RSSRK E1000_RSSRK #define E1000_82542_RSSIM E1000_RSSIM #define E1000_82542_RSSIR E1000_RSSIR -#define E1000_82542_KUMCTRLSTA E1000_KUMCTRLSTA -#define E1000_82542_SW_FW_SYNC E1000_SW_FW_SYNC /* Statistics counters collected by the MAC */ struct e1000_hw_stats { @@ -1327,7 +1303,6 @@ struct e1000_hw { e1000_ffe_config ffe_config_state; uint32_t asf_firmware_present; uint32_t eeprom_semaphore_present; - uint32_t swfw_sync_present; unsigned long io_base; uint32_t phy_id; uint32_t phy_revision; @@ -1386,7 +1361,6 @@ struct e1000_hw { boolean_t ifs_params_forced; boolean_t in_ifs_mode; boolean_t mng_reg_access_disabled; - boolean_t leave_av_bit_off; }; @@ -1419,8 +1393,6 @@ struct e1000_hw { #define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */ #define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */ #define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock indication in SDP[0] */ -#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through PHYRST_N pin */ -#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external LINK_0 and LINK_1 pins */ #define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */ #define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */ #define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */ @@ -1457,16 +1429,6 @@ struct e1000_hw { #define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */ #define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */ #define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */ -#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */ -#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */ -#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */ -#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */ -#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution disabled */ -#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */ -#define E1000_STATUS_FUSE_8 0x04000000 -#define E1000_STATUS_FUSE_9 0x08000000 -#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */ -#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */ /* Constants used to intrepret the masked PCI-X bus speed. */ #define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */ @@ -1544,8 +1506,6 @@ struct e1000_hw { #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000 #define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000 #define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000 -#define E1000_CTRL_EXT_LINK_MODE_KMRN 0x00000000 -#define E1000_CTRL_EXT_LINK_MODE_SERDES 0x00C00000 #define E1000_CTRL_EXT_WR_WMARK_MASK 0x03000000 #define E1000_CTRL_EXT_WR_WMARK_256 0x00000000 #define E1000_CTRL_EXT_WR_WMARK_320 0x01000000 @@ -1555,9 +1515,6 @@ struct e1000_hw { #define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */ #define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */ #define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */ -#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error detection enabled */ -#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity error detection enable */ -#define E1000_CTRL_EXT_GHOST_PAREN 0x40000000 /* MDI Control */ #define E1000_MDIC_DATA_MASK 0x0000FFFF @@ -1571,32 +1528,6 @@ struct e1000_hw { #define E1000_MDIC_INT_EN 0x20000000 #define E1000_MDIC_ERROR 0x40000000 -#define E1000_KUMCTRLSTA_MASK 0x0000FFFF -#define E1000_KUMCTRLSTA_OFFSET 0x001F0000 -#define E1000_KUMCTRLSTA_OFFSET_SHIFT 16 -#define E1000_KUMCTRLSTA_REN 0x00200000 - -#define E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL 0x00000000 -#define E1000_KUMCTRLSTA_OFFSET_CTRL 0x00000001 -#define E1000_KUMCTRLSTA_OFFSET_INB_CTRL 0x00000002 -#define E1000_KUMCTRLSTA_OFFSET_DIAG 0x00000003 -#define E1000_KUMCTRLSTA_OFFSET_TIMEOUTS 0x00000004 -#define E1000_KUMCTRLSTA_OFFSET_INB_PARAM 0x00000009 -#define E1000_KUMCTRLSTA_OFFSET_HD_CTRL 0x00000010 -#define E1000_KUMCTRLSTA_OFFSET_M2P_SERDES 0x0000001E -#define E1000_KUMCTRLSTA_OFFSET_M2P_MODES 0x0000001F - -/* FIFO Control */ -#define E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS 0x00000008 -#define E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS 0x00000800 - -/* In-Band Control */ -#define E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING 0x00000010 - -/* Half-Duplex Control */ -#define E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT 0x00000004 -#define E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT 0x00000000 - /* LED Control */ #define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F #define E1000_LEDCTL_LED0_MODE_SHIFT 0 @@ -1659,13 +1590,6 @@ struct e1000_hw { #define E1000_ICR_MNG 0x00040000 /* Manageability event */ #define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */ #define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */ -#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity error */ -#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */ -#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */ -#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */ /* Interrupt Cause Set */ #define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ @@ -1686,12 +1610,6 @@ struct e1000_hw { #define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */ #define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */ #define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */ -#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ -#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ -#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ /* Interrupt Mask Set */ #define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ @@ -1712,12 +1630,6 @@ struct e1000_hw { #define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */ #define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */ #define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */ -#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ -#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ -#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ /* Interrupt Mask Clear */ #define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */ @@ -1738,12 +1650,6 @@ struct e1000_hw { #define E1000_IMC_ACK E1000_ICR_ACK /* Receive Ack frame */ #define E1000_IMC_MNG E1000_ICR_MNG /* Manageability event */ #define E1000_IMC_DOCK E1000_ICR_DOCK /* Dock/Undock */ -#define E1000_IMC_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_IMC_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_IMC_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ -#define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ -#define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ /* Receive Control */ #define E1000_RCTL_RST 0x00000001 /* Software reset */ @@ -1813,12 +1719,6 @@ struct e1000_hw { #define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */ #define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */ -/* SW_W_SYNC definitions */ -#define E1000_SWFW_EEP_SM 0x0001 -#define E1000_SWFW_PHY0_SM 0x0002 -#define E1000_SWFW_PHY1_SM 0x0004 -#define E1000_SWFW_MAC_CSR_SM 0x0008 - /* Receive Descriptor */ #define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */ #define E1000_RDT_FPDB 0x80000000 /* Flush descriptor block */ @@ -1897,11 +1797,6 @@ struct e1000_hw { #define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */ #define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */ #define E1000_TCTL_MULR 0x10000000 /* Multiple request support */ -/* Extended Transmit Control */ -#define E1000_TCTL_EXT_BST_MASK 0x000003FF /* Backoff Slot Time */ -#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */ - -#define DEFAULT_80003ES2LAN_TCTL_EXT_GCEX 0x00010000 /* Receive Checksum Control */ #define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */ @@ -1979,7 +1874,6 @@ struct e1000_hw { #define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */ #define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */ #define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */ -#define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */ #define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */ #define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 /* Enable MAC address * filtering */ @@ -2068,19 +1962,19 @@ struct e1000_host_command_info { /* PCI-Ex registers */ /* PCI-Ex Control Register */ -#define E1000_GCR_RXD_NO_SNOOP 0x00000001 -#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002 -#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004 -#define E1000_GCR_TXD_NO_SNOOP 0x00000008 -#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010 -#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020 - -#define PCI_EX_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \ - E1000_GCR_RXDSCW_NO_SNOOP | \ - E1000_GCR_RXDSCR_NO_SNOOP | \ - E1000_GCR_TXD_NO_SNOOP | \ - E1000_GCR_TXDSCW_NO_SNOOP | \ - E1000_GCR_TXDSCR_NO_SNOOP) +#define E1000_GCR_RXD_NO_SNOOP 0x00000001 +#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002 +#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004 +#define E1000_GCR_TXD_NO_SNOOP 0x00000008 +#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010 +#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020 + +#define PCI_EX_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \ + E1000_GCR_RXDSCW_NO_SNOOP | \ + E1000_GCR_RXDSCR_NO_SNOOP | \ + E1000_GCR TXD_NO_SNOOP | \ + E1000_GCR_TXDSCW_NO_SNOOP | \ + E1000_GCR_TXDSCR_NO_SNOOP) #define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000 /* Function Active and Power State to MNG */ @@ -2141,14 +2035,12 @@ struct e1000_host_command_info { #define EEPROM_INIT_CONTROL1_REG 0x000A #define EEPROM_INIT_CONTROL2_REG 0x000F #define EEPROM_INIT_CONTROL3_PORT_B 0x0014 -#define EEPROM_INIT_3GIO_3 0x001A #define EEPROM_INIT_CONTROL3_PORT_A 0x0024 #define EEPROM_CFG 0x0012 #define EEPROM_FLASH_VERSION 0x0032 #define EEPROM_CHECKSUM_REG 0x003F #define E1000_EEPROM_CFG_DONE 0x00040000 /* MNG config cycle done */ -#define E1000_EEPROM_CFG_DONE_PORT_1 0x00080000 /* ...for second port */ /* Word definitions for ID LED Settings */ #define ID_LED_RESERVED_0000 0x0000 @@ -2192,9 +2084,6 @@ struct e1000_host_command_info { #define EEPROM_WORD0F_ANE 0x0800 #define EEPROM_WORD0F_SWPDIO_EXT 0x00F0 -/* Mask bits for fields in Word 0x1a of the EEPROM */ -#define EEPROM_WORD1A_ASPM_MASK 0x000C - /* For checksumming, the sum of all words in the EEPROM should equal 0xBABA. */ #define EEPROM_SUM 0xBABA @@ -2237,11 +2126,8 @@ struct e1000_host_command_info { #define DEFAULT_82542_TIPG_IPGR2 10 #define DEFAULT_82543_TIPG_IPGR2 6 -#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7 #define E1000_TIPG_IPGR2_SHIFT 20 -#define DEFAULT_80003ES2LAN_TIPG_IPGT_10_100 0x00000009 -#define DEFAULT_80003ES2LAN_TIPG_IPGT_1000 0x00000008 #define E1000_TXDMAC_DPP 0x00000001 /* Adaptive IFS defines */ @@ -2482,78 +2368,6 @@ struct e1000_host_command_info { #define IGP01E1000_ANALOG_REGS_PAGE 0x20C0 -/* Bits... - * 15-5: page - * 4-0: register offset - */ -#define GG82563_PAGE_SHIFT 5 -#define GG82563_REG(page, reg) \ - (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS)) -#define GG82563_MIN_ALT_REG 30 - -/* GG82563 Specific Registers */ -#define GG82563_PHY_SPEC_CTRL \ - GG82563_REG(0, 16) /* PHY Specific Control */ -#define GG82563_PHY_SPEC_STATUS \ - GG82563_REG(0, 17) /* PHY Specific Status */ -#define GG82563_PHY_INT_ENABLE \ - GG82563_REG(0, 18) /* Interrupt Enable */ -#define GG82563_PHY_SPEC_STATUS_2 \ - GG82563_REG(0, 19) /* PHY Specific Status 2 */ -#define GG82563_PHY_RX_ERR_CNTR \ - GG82563_REG(0, 21) /* Receive Error Counter */ -#define GG82563_PHY_PAGE_SELECT \ - GG82563_REG(0, 22) /* Page Select */ -#define GG82563_PHY_SPEC_CTRL_2 \ - GG82563_REG(0, 26) /* PHY Specific Control 2 */ -#define GG82563_PHY_PAGE_SELECT_ALT \ - GG82563_REG(0, 29) /* Alternate Page Select */ -#define GG82563_PHY_TEST_CLK_CTRL \ - GG82563_REG(0, 30) /* Test Clock Control (use reg. 29 to select) */ - -#define GG82563_PHY_MAC_SPEC_CTRL \ - GG82563_REG(2, 21) /* MAC Specific Control Register */ -#define GG82563_PHY_MAC_SPEC_CTRL_2 \ - GG82563_REG(2, 26) /* MAC Specific Control 2 */ - -#define GG82563_PHY_DSP_DISTANCE \ - GG82563_REG(5, 26) /* DSP Distance */ - -/* Page 193 - Port Control Registers */ -#define GG82563_PHY_KMRN_MODE_CTRL \ - GG82563_REG(193, 16) /* Kumeran Mode Control */ -#define GG82563_PHY_PORT_RESET \ - GG82563_REG(193, 17) /* Port Reset */ -#define GG82563_PHY_REVISION_ID \ - GG82563_REG(193, 18) /* Revision ID */ -#define GG82563_PHY_DEVICE_ID \ - GG82563_REG(193, 19) /* Device ID */ -#define GG82563_PHY_PWR_MGMT_CTRL \ - GG82563_REG(193, 20) /* Power Management Control */ -#define GG82563_PHY_RATE_ADAPT_CTRL \ - GG82563_REG(193, 25) /* Rate Adaptation Control */ - -/* Page 194 - KMRN Registers */ -#define GG82563_PHY_KMRN_FIFO_CTRL_STAT \ - GG82563_REG(194, 16) /* FIFO's Control/Status */ -#define GG82563_PHY_KMRN_CTRL \ - GG82563_REG(194, 17) /* Control */ -#define GG82563_PHY_INBAND_CTRL \ - GG82563_REG(194, 18) /* Inband Control */ -#define GG82563_PHY_KMRN_DIAGNOSTIC \ - GG82563_REG(194, 19) /* Diagnostic */ -#define GG82563_PHY_ACK_TIMEOUTS \ - GG82563_REG(194, 20) /* Acknowledge Timeouts */ -#define GG82563_PHY_ADV_ABILITY \ - GG82563_REG(194, 21) /* Advertised Ability */ -#define GG82563_PHY_LINK_PARTNER_ADV_ABILITY \ - GG82563_REG(194, 23) /* Link Partner Advertised Ability */ -#define GG82563_PHY_ADV_NEXT_PAGE \ - GG82563_REG(194, 24) /* Advertised Next Page */ -#define GG82563_PHY_LINK_PARTNER_ADV_NEXT_PAGE \ - GG82563_REG(194, 25) /* Link Partner Advertised Next page */ -#define GG82563_PHY_KMRN_MISC \ - GG82563_REG(194, 26) /* Misc. */ /* PHY Control Register */ #define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */ @@ -2867,113 +2681,6 @@ struct e1000_host_command_info { #define IGP01E1000_ANALOG_FUSE_FINE_1 0x0080 #define IGP01E1000_ANALOG_FUSE_FINE_10 0x0500 -/* GG82563 PHY Specific Status Register (Page 0, Register 16 */ -#define GG82563_PSCR_DISABLE_JABBER 0x0001 /* 1=Disable Jabber */ -#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Polarity Reversal Disabled */ -#define GG82563_PSCR_POWER_DOWN 0x0004 /* 1=Power Down */ -#define GG82563_PSCR_COPPER_TRANSMITER_DISABLE 0x0008 /* 1=Transmitter Disabled */ -#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060 -#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI configuration */ -#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX configuration */ -#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Automatic crossover */ -#define GG82563_PSCR_ENALBE_EXTENDED_DISTANCE 0x0080 /* 1=Enable Extended Distance */ -#define GG82563_PSCR_ENERGY_DETECT_MASK 0x0300 -#define GG82563_PSCR_ENERGY_DETECT_OFF 0x0000 /* 00,01=Off */ -#define GG82563_PSCR_ENERGY_DETECT_RX 0x0200 /* 10=Sense on Rx only (Energy Detect) */ -#define GG82563_PSCR_ENERGY_DETECT_RX_TM 0x0300 /* 11=Sense and Tx NLP */ -#define GG82563_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force Link Good */ -#define GG82563_PSCR_DOWNSHIFT_ENABLE 0x0800 /* 1=Enable Downshift */ -#define GG82563_PSCR_DOWNSHIFT_COUNTER_MASK 0x7000 -#define GG82563_PSCR_DOWNSHIFT_COUNTER_SHIFT 12 - -/* PHY Specific Status Register (Page 0, Register 17) */ -#define GG82563_PSSR_JABBER 0x0001 /* 1=Jabber */ -#define GG82563_PSSR_POLARITY 0x0002 /* 1=Polarity Reversed */ -#define GG82563_PSSR_LINK 0x0008 /* 1=Link is Up */ -#define GG82563_PSSR_ENERGY_DETECT 0x0010 /* 1=Sleep, 0=Active */ -#define GG82563_PSSR_DOWNSHIFT 0x0020 /* 1=Downshift */ -#define GG82563_PSSR_CROSSOVER_STATUS 0x0040 /* 1=MDIX, 0=MDI */ -#define GG82563_PSSR_RX_PAUSE_ENABLED 0x0100 /* 1=Receive Pause Enabled */ -#define GG82563_PSSR_TX_PAUSE_ENABLED 0x0200 /* 1=Transmit Pause Enabled */ -#define GG82563_PSSR_LINK_UP 0x0400 /* 1=Link Up */ -#define GG82563_PSSR_SPEED_DUPLEX_RESOLVED 0x0800 /* 1=Resolved */ -#define GG82563_PSSR_PAGE_RECEIVED 0x1000 /* 1=Page Received */ -#define GG82563_PSSR_DUPLEX 0x2000 /* 1-Full-Duplex */ -#define GG82563_PSSR_SPEED_MASK 0xC000 -#define GG82563_PSSR_SPEED_10MBPS 0x0000 /* 00=10Mbps */ -#define GG82563_PSSR_SPEED_100MBPS 0x4000 /* 01=100Mbps */ -#define GG82563_PSSR_SPEED_1000MBPS 0x8000 /* 10=1000Mbps */ - -/* PHY Specific Status Register 2 (Page 0, Register 19) */ -#define GG82563_PSSR2_JABBER 0x0001 /* 1=Jabber */ -#define GG82563_PSSR2_POLARITY_CHANGED 0x0002 /* 1=Polarity Changed */ -#define GG82563_PSSR2_ENERGY_DETECT_CHANGED 0x0010 /* 1=Energy Detect Changed */ -#define GG82563_PSSR2_DOWNSHIFT_INTERRUPT 0x0020 /* 1=Downshift Detected */ -#define GG82563_PSSR2_MDI_CROSSOVER_CHANGE 0x0040 /* 1=Crossover Changed */ -#define GG82563_PSSR2_FALSE_CARRIER 0x0100 /* 1=False Carrier */ -#define GG82563_PSSR2_SYMBOL_ERROR 0x0200 /* 1=Symbol Error */ -#define GG82563_PSSR2_LINK_STATUS_CHANGED 0x0400 /* 1=Link Status Changed */ -#define GG82563_PSSR2_AUTO_NEG_COMPLETED 0x0800 /* 1=Auto-Neg Completed */ -#define GG82563_PSSR2_PAGE_RECEIVED 0x1000 /* 1=Page Received */ -#define GG82563_PSSR2_DUPLEX_CHANGED 0x2000 /* 1=Duplex Changed */ -#define GG82563_PSSR2_SPEED_CHANGED 0x4000 /* 1=Speed Changed */ -#define GG82563_PSSR2_AUTO_NEG_ERROR 0x8000 /* 1=Auto-Neg Error */ - -/* PHY Specific Control Register 2 (Page 0, Register 26) */ -#define GG82563_PSCR2_10BT_POLARITY_FORCE 0x0002 /* 1=Force Negative Polarity */ -#define GG82563_PSCR2_1000MB_TEST_SELECT_MASK 0x000C -#define GG82563_PSCR2_1000MB_TEST_SELECT_NORMAL 0x0000 /* 00,01=Normal Operation */ -#define GG82563_PSCR2_1000MB_TEST_SELECT_112NS 0x0008 /* 10=Select 112ns Sequence */ -#define GG82563_PSCR2_1000MB_TEST_SELECT_16NS 0x000C /* 11=Select 16ns Sequence */ -#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000 /* 1=Reverse Auto-Negotiation */ -#define GG82563_PSCR2_1000BT_DISABLE 0x4000 /* 1=Disable 1000BASE-T */ -#define GG82563_PSCR2_TRANSMITER_TYPE_MASK 0x8000 -#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_B 0x0000 /* 0=Class B */ -#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_A 0x8000 /* 1=Class A */ - -/* MAC Specific Control Register (Page 2, Register 21) */ -/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */ -#define GG82563_MSCR_TX_CLK_MASK 0x0007 -#define GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ 0x0004 -#define GG82563_MSCR_TX_CLK_100MBPS_25MHZ 0x0005 -#define GG82563_MSCR_TX_CLK_1000MBPS_2_5MHZ 0x0006 -#define GG82563_MSCR_TX_CLK_1000MBPS_25MHZ 0x0007 - -#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */ - -/* DSP Distance Register (Page 5, Register 26) */ -#define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M; - 1 = 50-80M; - 2 = 80-110M; - 3 = 110-140M; - 4 = >140M */ - -/* Kumeran Mode Control Register (Page 193, Register 16) */ -#define GG82563_KMCR_PHY_LEDS_EN 0x0020 /* 1=PHY LEDs, 0=Kumeran Inband LEDs */ -#define GG82563_KMCR_FORCE_LINK_UP 0x0040 /* 1=Force Link Up */ -#define GG82563_KMCR_SUPPRESS_SGMII_EPD_EXT 0x0080 -#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT_MASK 0x0400 -#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT 0x0400 /* 1=6.25MHz, 0=0.8MHz */ -#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800 - -/* Power Management Control Register (Page 193, Register 20) */ -#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001 /* 1=Enalbe SERDES Electrical Idle */ -#define GG82563_PMCR_DISABLE_PORT 0x0002 /* 1=Disable Port */ -#define GG82563_PMCR_DISABLE_SERDES 0x0004 /* 1=Disable SERDES */ -#define GG82563_PMCR_REVERSE_AUTO_NEG 0x0008 /* 1=Enable Reverse Auto-Negotiation */ -#define GG82563_PMCR_DISABLE_1000_NON_D0 0x0010 /* 1=Disable 1000Mbps Auto-Neg in non D0 */ -#define GG82563_PMCR_DISABLE_1000 0x0020 /* 1=Disable 1000Mbps Auto-Neg Always */ -#define GG82563_PMCR_REVERSE_AUTO_NEG_D0A 0x0040 /* 1=Enable D0a Reverse Auto-Negotiation */ -#define GG82563_PMCR_FORCE_POWER_STATE 0x0080 /* 1=Force Power State */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_MASK 0x0300 -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_DR 0x0000 /* 00=Dr */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0U 0x0100 /* 01=D0u */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0A 0x0200 /* 10=D0a */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D3 0x0300 /* 11=D3 */ - -/* In-Band Control Register (Page 194, Register 18) */ -#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding Use */ - /* Bit definitions for valid PHY IDs. */ /* I = Integrated @@ -2988,7 +2695,6 @@ struct e1000_host_command_info { #define M88E1011_I_REV_4 0x04 #define M88E1111_I_PHY_ID 0x01410CC0 #define L1LXT971A_PHY_ID 0x001378E0 -#define GG82563_E_PHY_ID 0x01410CA0 /* Miscellaneous PHY bit definitions. */ #define PHY_PREAMBLE 0xFFFFFFFF