X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=drivers%2Fnet%2Fioc3-eth.c;h=ae71ed57c12db04f624f01d4c7c9324576376f06;hb=43bc926fffd92024b46cafaf7350d669ba9ca884;hp=d520b5920d6cc866053dc23b3df7887839f52f4f;hpb=f7f1b0f1e2fbadeab12d24236000e778aa9b1ead;p=linux-2.6.git

diff --git a/drivers/net/ioc3-eth.c b/drivers/net/ioc3-eth.c
index d520b5920..ae71ed57c 100644
--- a/drivers/net/ioc3-eth.c
+++ b/drivers/net/ioc3-eth.c
@@ -44,12 +44,11 @@
 #include <linux/ip.h>
 #include <linux/tcp.h>
 #include <linux/udp.h>
+#include <linux/dma-mapping.h>
 
 #ifdef CONFIG_SERIAL_8250
-#include <linux/serial.h>
-#include <asm/serial.h>
-#define IOC3_BAUD (22000000 / (3*16))
-#define IOC3_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
+#include <linux/serial_core.h>
+#include <linux/serial_8250.h>
 #endif
 
 #include <linux/netdevice.h>
@@ -499,7 +498,7 @@ static int ioc3_mdio_read(struct net_device *dev, int phy, int reg)
 	ioc3_w_micr((phy << MICR_PHYADDR_SHIFT) | reg | MICR_READTRIG);
 	while (ioc3_r_micr() & MICR_BUSY);
 
-	return ioc3_r_micr() & MIDR_DATA_MASK;
+	return ioc3_r_midr_r() & MIDR_DATA_MASK;
 }
 
 static void ioc3_mdio_write(struct net_device *dev, int phy, int reg, int data)
@@ -1146,12 +1145,11 @@ static inline int ioc3_is_menet(struct pci_dev *pdev)
  * around ioc3 oddities in this respect.
  *
  * The IOC3 serials use a 22MHz clock rate with an additional divider by 3.
- * (IOC3_BAUD = (22000000 / (3*16)))
  */
 
 static void __devinit ioc3_serial_probe(struct pci_dev *pdev, struct ioc3 *ioc3)
 {
-	struct serial_struct req;
+	struct uart_port port;
 
 	/*
 	 * We need to recognice and treat the fourth MENET serial as it
@@ -1165,20 +1163,25 @@ static void __devinit ioc3_serial_probe(struct pci_dev *pdev, struct ioc3 *ioc3)
 	if (ioc3_is_menet(pdev) && PCI_SLOT(pdev->devfn) == 3)
 		return;
 
-	/* Register to interrupt zero because we share the interrupt with
-	   the serial driver which we don't properly support yet.  */
-	memset(&req, 0, sizeof(req));
-	req.irq             = 0;
-	req.flags           = IOC3_COM_FLAGS;
-	req.io_type         = SERIAL_IO_MEM;
-	req.iomem_reg_shift = 0;
-	req.baud_base       = IOC3_BAUD;
-
-	req.iomem_base      = (unsigned char *) &ioc3->sregs.uarta;
-	register_serial(&req);
-
-	req.iomem_base      = (unsigned char *) &ioc3->sregs.uartb;
-	register_serial(&req);
+	/*
+	 * Register to interrupt zero because we share the interrupt with
+	 * the serial driver which we don't properly support yet.
+	 *
+	 * Can't use UPF_IOREMAP as the whole of IOC3 resources have already
+	 * been registered.
+	 */
+	memset(&port, 0, sizeof(port));
+	port.irq      = 0;
+	port.flags    = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
+	port.iotype   = UPIO_MEM;
+	port.regshift = 0;
+	port.uartclk  = 22000000 / 3;
+
+	port.membase  = (unsigned char *) &ioc3->sregs.uarta;
+	serial8250_register_port(&port);
+
+	port.membase  = (unsigned char *) &ioc3->sregs.uartb;
+	serial8250_register_port(&port);
 }
 #endif
 
@@ -1193,17 +1196,17 @@ static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	int err, pci_using_dac;
 
 	/* Configure DMA attributes. */
-	err = pci_set_dma_mask(pdev, 0xffffffffffffffffULL);
+	err = pci_set_dma_mask(pdev, DMA_64BIT_MASK);
 	if (!err) {
 		pci_using_dac = 1;
-		err = pci_set_consistent_dma_mask(pdev, 0xffffffffffffffffULL);
+		err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
 		if (err < 0) {
 			printk(KERN_ERR "%s: Unable to obtain 64 bit DMA "
 			       "for consistent allocations\n", pci_name(pdev));
 			goto out;
 		}
 	} else {
-		err = pci_set_dma_mask(pdev, 0xffffffffULL);
+		err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
 		if (err) {
 			printk(KERN_ERR "%s: No usable DMA configuration, "
 			       "aborting.\n", pci_name(pdev));
@@ -1291,7 +1294,6 @@ static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	dev->features		= NETIF_F_IP_CSUM;
 #endif
 
-	ioc3_setup_duplex(ip);
 	sw_physid1 = ioc3_mdio_read(dev, ip->mii.phy_id, MII_PHYSID1);
 	sw_physid2 = ioc3_mdio_read(dev, ip->mii.phy_id, MII_PHYSID2);
 
@@ -1300,6 +1302,7 @@ static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 		goto out_stop;
 
 	mii_check_media(&ip->mii, 1, 1);
+	ioc3_setup_duplex(ip);
 
 	vendor = (sw_physid1 << 12) | (sw_physid2 >> 4);
 	model  = (sw_physid2 >> 4) & 0x3f;
@@ -1358,7 +1361,7 @@ static struct pci_driver ioc3_driver = {
 
 static int __init ioc3_init_module(void)
 {
-	return pci_module_init(&ioc3_driver);
+	return pci_register_driver(&ioc3_driver);
 }
 
 static void __exit ioc3_cleanup_module(void)
@@ -1524,7 +1527,7 @@ static void ioc3_get_drvinfo (struct net_device *dev,
 	struct ethtool_drvinfo *info)
 {
 	struct ioc3_private *ip = netdev_priv(dev);
-                                                                                
+
         strcpy (info->driver, IOC3_NAME);
         strcpy (info->version, IOC3_VERSION);
         strcpy (info->bus_info, pci_name(ip->pdev));
@@ -1550,7 +1553,7 @@ static int ioc3_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 	spin_lock_irq(&ip->ioc3_lock);
 	rc = mii_ethtool_sset(&ip->mii, cmd);
 	spin_unlock_irq(&ip->ioc3_lock);
-                                                                        
+
 	return rc;
 }