X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=drivers%2Fnet%2Fwan%2FKconfig;h=4d5844f75b5f8d24c46b84bf855858a0d15f1080;hb=746550cff061581f89c687ada8523670768364f2;hp=2baf40a8ae89d54518fa29a0475d0cf29997289e;hpb=86090fcac5e27b630656fe3d963a6b80e26dac44;p=linux-2.6.git diff --git a/drivers/net/wan/Kconfig b/drivers/net/wan/Kconfig index 2baf40a8a..4d5844f75 100644 --- a/drivers/net/wan/Kconfig +++ b/drivers/net/wan/Kconfig @@ -57,119 +57,6 @@ config COSA The driver will be compiled as a module: the module will be called cosa. -# -# COMX drivers -# -# Not updated to 2.6. -config COMX - tristate "MultiGate (COMX) synchronous serial boards support" - depends on WAN && (ISA || PCI) && BROKEN - ---help--- - Drivers for the PC synchronous serial adapters by - ITConsult-Pro Co, Hungary. - - Read for help on configuring - and using COMX interfaces. Further info on these cards can be found - at or . - - Say Y if you want to use any board from the MultiGate (COMX) - family, you must also say Y to "/proc file system support" - (CONFIG_PROC_FS) in order to use these drivers. - - To compile this driver as a module, choose M here: the - module will be called comx. - -config COMX_HW_COMX - tristate "Support for COMX/CMX/HiCOMX boards" - depends on COMX - help - Driver for the 'CMX', 'COMX' and 'HiCOMX' boards. - - You will need additional firmware to use these cards, which are - downloadable from . - - Say Y if you have a board like this. - - To compile this driver as a module, choose M here: the - module will be called comx-hw-comx. - -config COMX_HW_LOCOMX - tristate "Support for LoCOMX board" - depends on COMX - help - Driver for the 'LoCOMX' board. - - Say Y if you have a board like this. - - To compile this driver as a module, choose M here: the - module will be called comx-hw-locomx. - -config COMX_HW_MIXCOM - tristate "Support for MixCOM board" - depends on COMX - ---help--- - Driver for the 'MixCOM' board. - - If you want to use the watchdog device on this card, you should - select it in the Watchdog Cards section of the Character Devices - configuration. The ISDN interface of this card is Teles 16.3 - compatible, you should enable it in the ISDN configuration menu. The - driver for the flash ROM of this card is available separately on - . - - Say Y if you have a board like this. - - To compile this driver as a module, choose M here: the - module will be called comx-hw-mixcom. - -config COMX_HW_MUNICH - tristate "Support for MUNICH based boards: SliceCOM, PCICOM (WelCOM)" - depends on COMX - ---help--- - Driver for the 'SliceCOM' (channelized E1) and 'PciCOM' (X21) boards. - - Read for help on - configuring and using SliceCOM interfaces. Further info on these - cards can be found at or . - - Say Y if you have a board like this. - - To compile this driver as a module, choose M here: the - module will be called comx-hw-munich. - -config COMX_PROTO_PPP - tristate "Support for HDLC and syncPPP protocols on MultiGate boards" - depends on COMX - help - Cisco-HDLC and synchronous PPP protocol driver. - - Say Y if you want to use either protocol. - - To compile this as a module, choose M here: the - module will be called comx-proto-ppp. - -config COMX_PROTO_LAPB - tristate "Support for LAPB protocol on MultiGate boards" - depends on WAN && (COMX!=n && LAPB=m && LAPB || LAPB=y && COMX) - help - LAPB protocol driver. - - Say Y if you want to use this protocol. - - To compile this as a module, choose M here: the - module will be called comx-proto-lapb. - -config COMX_PROTO_FR - tristate "Support for Frame Relay on MultiGate boards" - depends on COMX - help - Frame Relay protocol driver. - - Say Y if you want to use this protocol. - - To compile this as a module, choose M here: the - module will be called comx-proto-fr. - config DSCC4 tristate "Etinc PCISYNC serial board support" depends on WAN && PCI && m