X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=drivers%2Fusb%2Fstorage%2FKconfig;h=be9eec2257436c2152aecd9e0d20462f69902b2e;hb=43bc926fffd92024b46cafaf7350d669ba9ca884;hp=f1f1c0608c22a9f471aa88779e97f5bde4846fa2;hpb=cee37fe97739d85991964371c1f3a745c00dd236;p=linux-2.6.git

diff --git a/drivers/usb/storage/Kconfig b/drivers/usb/storage/Kconfig
index f1f1c0608..be9eec225 100644
--- a/drivers/usb/storage/Kconfig
+++ b/drivers/usb/storage/Kconfig
@@ -2,7 +2,8 @@
 # USB Storage driver configuration
 #
 
-comment "NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information"
+comment "NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'"
+comment "may also be needed; see USB_STORAGE Help for more information"
 	depends on USB
 
 config USB_STORAGE
@@ -47,7 +48,8 @@ config USB_STORAGE_FREECOM
 
 config USB_STORAGE_ISD200
 	bool "ISD-200 USB/ATA Bridge support"
-	depends on USB_STORAGE && BLK_DEV_IDE
+	depends on USB_STORAGE
+	depends on BLK_DEV_IDE=y || BLK_DEV_IDE=USB_STORAGE
 	---help---
 	  Say Y here if you want to use USB Mass Store devices based
 	  on the In-Systems Design ISD-200 USB/ATA bridge.
@@ -111,3 +113,38 @@ config USB_STORAGE_JUMPSHOT
 	  Say Y here to include additional code to support the Lexar Jumpshot
 	  USB CompactFlash reader.
 
+config USB_STORAGE_ALAUDA
+	bool "Olympus MAUSB-10/Fuji DPC-R1 support (EXPERIMENTAL)"
+	depends on USB_STORAGE && EXPERIMENTAL
+	help
+	  Say Y here to include additional code to support the Olympus MAUSB-10
+	  and Fujifilm DPC-R1 USB Card reader/writer devices.
+
+	  These devices are based on the Alauda chip and support support both
+	  XD and SmartMedia cards.
+
+config USB_STORAGE_ONETOUCH
+	bool "Support OneTouch Button on Maxtor Hard Drives (EXPERIMENTAL)"
+	depends on USB_STORAGE && INPUT_EVDEV && EXPERIMENTAL && !PM
+	help
+	  Say Y here to include additional code to support the Maxtor OneTouch
+	  USB hard drive's onetouch button.
+
+	  This code registers the button on the front of Maxtor OneTouch USB
+	  hard drive's as an input device. An action can be associated with
+	  this input in any keybinding software. (e.g. gnome's keyboard short-
+	  cuts)
+
+config USB_LIBUSUAL
+	bool "The shared table of common (or usual) storage devices"
+	depends on USB
+	help
+	  This module contains a table of common (or usual) devices
+	  for usb-storage and ub drivers, and allows to switch binding
+	  of these devices without rebuilding modules.
+
+	  Typical syntax of /etc/modprobe.conf is:
+
+		options libusual bias="ub"
+
+	  If unsure, say N.