X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=include%2Fasm-arm%2Farch-at91rm9200%2Fboard.h;h=768e0fc6aa2f2d6b08250ec67f3346f5b5d5a4d6;hb=97bf2856c6014879bd04983a3e9dfcdac1e7fe85;hp=2e7d1139a799827d4942e0c187b56ef6c1388232;hpb=76828883507a47dae78837ab5dec5a5b4513c667;p=linux-2.6.git

diff --git a/include/asm-arm/arch-at91rm9200/board.h b/include/asm-arm/arch-at91rm9200/board.h
index 2e7d1139a..768e0fc6a 100644
--- a/include/asm-arm/arch-at91rm9200/board.h
+++ b/include/asm-arm/arch-at91rm9200/board.h
@@ -20,7 +20,7 @@
 
 /*
  * These are data structures found in platform_device.dev.platform_data,
- * and describing board-specfic data needed by drivers.  For example,
+ * and describing board-specific data needed by drivers.  For example,
  * which pin is used for a given GPIO role.
  *
  * In 2.6, drivers should strongly avoid board-specific knowledge so
@@ -31,12 +31,9 @@
 #ifndef __ASM_ARCH_BOARD_H
 #define __ASM_ARCH_BOARD_H
 
- /* Clocks */
-extern unsigned long at91_master_clock;
-
- /* Serial Port */
-extern int at91_serial_map[AT91_NR_UART];
-extern int at91_console_port;
+#include <linux/mtd/partitions.h>
+#include <linux/device.h>
+#include <linux/spi/spi.h>
 
  /* USB Device */
 struct at91_udc_data {
@@ -51,13 +48,14 @@ struct at91_cf_data {
 	u8	det_pin;		/* Card detect */
 	u8	vcc_pin;		/* power switching */
 	u8	rst_pin;		/* card reset */
+	u8	chipselect;		/* EBI Chip Select number */
 };
 extern void __init at91_add_device_cf(struct at91_cf_data *data);
 
  /* MMC / SD */
 struct at91_mmc_data {
 	u8		det_pin;	/* card detect IRQ */
-	unsigned	is_b:1;		/* uses B side (vs A) */
+	unsigned	slot_b:1;	/* uses Slot B */
 	unsigned	wire4:1;	/* (SD) supports DAT0..DAT3 */
 	u8		wp_pin;		/* (SD) writeprotect detect */
 	u8		vcc_pin;	/* power switching (high == on) */
@@ -77,4 +75,43 @@ struct at91_usbh_data {
 };
 extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
 
+ /* NAND / SmartMedia */
+struct at91_nand_data {
+	u8		enable_pin;	/* chip enable */
+	u8		det_pin;	/* card detect */
+	u8		rdy_pin;	/* ready/busy */
+	u8		ale;		/* address line number connected to ALE */
+	u8		cle;		/* address line number connected to CLE */
+	u8		bus_width_16;	/* buswidth is 16 bit */
+	struct mtd_partition* (*partition_info)(int, int*);
+};
+extern void __init at91_add_device_nand(struct at91_nand_data *data);
+
+ /* I2C*/
+extern void __init at91_add_device_i2c(void);
+
+ /* SPI */
+extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
+
+ /* Serial */
+struct at91_uart_config {
+	unsigned short	console_tty;	/* tty number of serial console */
+	unsigned short	nr_tty;		/* number of serial tty's */
+	short		tty_map[];	/* map UART to tty number */
+};
+extern struct platform_device *atmel_default_console_device;
+extern void __init at91_init_serial(struct at91_uart_config *config);
+
+struct atmel_uart_data {
+	short		use_dma_tx;	/* use transmit DMA? */
+	short		use_dma_rx;	/* use receive DMA? */
+	void __iomem	*regs;		/* virtual base address, if any */
+};
+extern void __init at91_add_device_serial(void);
+
+ /* LEDs */
+extern u8 at91_leds_cpu;
+extern u8 at91_leds_timer;
+extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
+
 #endif