X-Git-Url: http://git.onelab.eu/?a=blobdiff_plain;f=vswitchd%2Fvswitch.xml;h=18643c20e8523d92a9a863c2e9f63351d2016cd0;hb=eb857b4824d2a62e1cc1b85c30a3da007d4942c9;hp=0bc4ccdc86a6c4e56f59f12b35712596e1ea2c61;hpb=85b53b3110a1c97c4eaaf647adb8ab8afbeba0e7;p=sliver-openvswitch.git diff --git a/vswitchd/vswitch.xml b/vswitchd/vswitch.xml index 0bc4ccdc8..18643c20e 100644 --- a/vswitchd/vswitch.xml +++ b/vswitchd/vswitch.xml @@ -439,6 +439,12 @@ value. May not be all-zero. + + Human readable description of datapath. It it a maximum 256 + byte-long free-form string to describe the datapath for + debugging purposes, e.g. switch3 in room 3120. + + If set to true, disable in-band control on the bridge @@ -453,6 +459,12 @@ QoS configured, or if the port does not have a queue with the specified ID, the default queue is used instead. + + + List of OpenFlow protocols that may be used when negotiating a + connection with a controller. A default value of + OpenFlow10 will be used if this column is empty. + @@ -617,6 +629,15 @@ transmit packets.

+ + +

+ The maximum number of MAC addresses to learn. The default is + currently 2048. The value, if specified, is forced into a reasonable + range, currently 10 to 1,000,000. +

+ @@ -1158,6 +1179,20 @@ port number for the OpenFlow ``local port''). If the interface cannot be added then Open vSwitch sets this column to -1.

+

When is not set, Open vSwitch picks + an appropriate value for this column and then tries to keep the value + constant across restarts.

+ + + +

Requested OpenFlow port number for this interface. The port + number must be between 1 and 65279, inclusive. Some datapaths + cannot satisfy all requests for particular port numbers. When + this column is empty or the request cannot be fulfilled, the + system will choose a free port. The + column reports the assigned OpenFlow port number.

+

The port number must be requested in the same transaction + that creates the port.

 @@ -1189,8 +1224,7 @@
gre
An Ethernet over RFC 2890 Generic Routing Encapsulation over IPv4 - tunnel. See for information on - configuring GRE tunnels. + tunnel.
ipsec_gre
@@ -1222,6 +1256,26 @@ implemented. UDP ports 58881 and 58882 are used as the source and destination ports respectively. CAPWAP is currently supported only with the Linux kernel datapath with kernel version 2.6.26 or later. + + CAPWAP support is deprecated and will be removed no earlier than + February 2013. + + +
vxlan
+
+

+ An Ethernet tunnel over the experimental, UDP-based VXLAN + protocol described at + http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02. + VXLAN is currently supported only with the Linux kernel datapath + with kernel version 2.6.26 or later. +

+

+ As an experimental protocol, VXLAN has no officially assigned UDP + port. Open vSwitch currently uses UDP destination port 8472. + The source port used for VXLAN traffic varies on a per-flow basis + and is in the ephemeral port range. +

patch
@@ -1240,7 +1294,8 @@

These options apply to interfaces with of gre, ipsec_gre, gre64, - ipsec_gre64, and capwap. + ipsec_gre64, capwap, and + vxlan.

@@ -1283,8 +1338,9 @@ key="in_key"/> at all.

  • - A positive 32-bit (for GRE) or 64-bit (for CAPWAP) number. The - tunnel receives only packets with the specified key. + A positive 24-bit (for VXLAN), 32-bit (for GRE) or 64-bit (for + CAPWAP) number. The tunnel receives only packets with the + specified key.
  • The word flow. The tunnel accepts packets with any @@ -1309,8 +1365,9 @@ key="out_key"/> at all.
  • - A positive 32-bit (for GRE) or 64-bit (for CAPWAP) number. Packets - sent through the tunnel will have the specified key. + A positive 24-bit (for VXLAN), 32-bit (for GRE) or 64-bit (for + CAPWAP) number. Packets sent through the tunnel will have the + specified key.
  • The word flow. Packets sent through the tunnel will @@ -1343,48 +1400,13 @@ system default, typically 64). Default is the system default TTL. - - Optional. If enabled, the Don't Fragment bit will be copied from the - inner IP headers (those of the encapsulated traffic) to the outer - (tunnel) headers. Default is disabled; set to true to - enable. - - - Optional. If enabled, the Don't Fragment bit will be set by default on - tunnel headers if the df_inherit option is not set, or if - the encapsulated packet is not IP. Default is enabled; set to - false to disable. - - - - Optional. Enable tunnel path MTU discovery. If enabled ``ICMP - Destination Unreachable - Fragmentation Needed'' messages will be - generated for IPv4 packets with the DF bit set and IPv6 packets above - the minimum MTU if the packet size exceeds the path MTU minus the size - of the tunnel headers. Note that this option causes behavior that is - typically reserved for routers and therefore is not entirely in - compliance with the IEEE 802.1D specification for bridges. Default is - disabled; set to true to enable. + Optional. If enabled, the Don't Fragment bit will be set on tunnel + outer headers to allow path MTU discovery. Default is enabled; set + to false to disable. - -

    - Only gre interfaces support these options. -

    - - - Enable caching of tunnel headers and the output path. This can lead - to a significant performance increase without changing behavior. In - general it should not be necessary to adjust this setting. However, - the caching can bypass certain components of the IP stack (such as - iptables) and it may be useful to disable it if these - features are required or as a debugging measure. Default is enabled, - set to false to disable. - -     -

    Only gre and ipsec_gre interfaces support