#include <asm/arch/cpu.h>
#endif
#include <asm/arch/io.h>
+#include <asm/arch/serial.h>
/*
* ---------------------------------------------------------------------------
* ---------------------------------------------------------------------------
*/
+/*
+ * ----------------------------------------------------------------------------
+ * Timers
+ * ----------------------------------------------------------------------------
+ */
+#define OMAP_MPU_TIMER1_BASE (0xfffec500)
+#define OMAP_MPU_TIMER2_BASE (0xfffec600)
+#define OMAP_MPU_TIMER3_BASE (0xfffec700)
+#define MPU_TIMER_FREE (1 << 6)
+#define MPU_TIMER_CLOCK_ENABLE (1 << 5)
+#define MPU_TIMER_AR (1 << 1)
+#define MPU_TIMER_ST (1 << 0)
+
/*
* ----------------------------------------------------------------------------
* Clocks
/* DPLL control registers */
#define DPLL_CTL (0xfffecf00)
-/* DSP clock control */
+/* DSP clock control. Must use __raw_readw() and __raw_writew() with these */
#define DSP_CONFIG_REG_BASE (0xe1008000)
+#define DSP_CKCTL (DSP_CONFIG_REG_BASE + 0x0)
#define DSP_IDLECT1 (DSP_CONFIG_REG_BASE + 0x4)
#define DSP_IDLECT2 (DSP_CONFIG_REG_BASE + 0x8)
+#define DSP_RSTCT2 (DSP_CONFIG_REG_BASE + 0x14)
/*
* ---------------------------------------------------------------------------
*/
#define ULPD_REG_BASE (0xfffe0800)
#define ULPD_IT_STATUS (ULPD_REG_BASE + 0x14)
+#define ULPD_SETUP_ANALOG_CELL_3 (ULPD_REG_BASE + 0x24)
#define ULPD_CLOCK_CTRL (ULPD_REG_BASE + 0x30)
# define DIS_USB_PVCI_CLK (1 << 5) /* no USB/FAC synch */
# define USB_MCLK_EN (1 << 4) /* enable W4_USB_CLKO */
* Interrupts
* ---------------------------------------------------------------------------
*/
+#ifdef CONFIG_ARCH_OMAP1
+
+/*
+ * XXX: These probably want to be moved to arch/arm/mach-omap/omap1/irq.c
+ * or something similar.. -- PFM.
+ */
+
#define OMAP_IH1_BASE 0xfffecb00
#define OMAP_IH2_BASE 0xfffe0000
#define IRQ_ILR0_REG_OFFSET 0x1c
#define IRQ_GMR_REG_OFFSET 0xa0
+#endif
+
/*
* ----------------------------------------------------------------------------
* System control registers
#define OMAP_LPG2_LCR (OMAP_LPG2_BASE + 0x00)
#define OMAP_LPG2_PMR (OMAP_LPG2_BASE + 0x04)
-#ifndef __ASSEMBLER__
-
-/*
- * ---------------------------------------------------------------------------
- * Serial ports
- * ---------------------------------------------------------------------------
- */
-#define OMAP_UART1_BASE (unsigned char *)0xfffb0000
-#define OMAP_UART2_BASE (unsigned char *)0xfffb0800
-#define OMAP_UART3_BASE (unsigned char *)0xfffb9800
-#define OMAP_MAX_NR_PORTS 3
-#define OMAP1510_BASE_BAUD (12000000/16)
-#define OMAP16XX_BASE_BAUD (48000000/16)
-
-#define is_omap_port(p) ({int __ret = 0; \
- if (p == IO_ADDRESS(OMAP_UART1_BASE) || \
- p == IO_ADDRESS(OMAP_UART2_BASE) || \
- p == IO_ADDRESS(OMAP_UART3_BASE)) \
- __ret = 1; \
- __ret; \
- })
-
/*
* ---------------------------------------------------------------------------
* Processor specific defines
* ---------------------------------------------------------------------------
*/
-#ifdef CONFIG_ARCH_OMAP730
-#include "omap730.h"
-#endif
-#ifdef CONFIG_ARCH_OMAP1510
+#include "omap730.h"
#include "omap1510.h"
-#endif
-
-#ifdef CONFIG_ARCH_OMAP16XX
+#include "omap24xx.h"
#include "omap16xx.h"
-#endif
+
+#ifndef __ASSEMBLER__
/*
* ---------------------------------------------------------------------------
#ifdef CONFIG_MACH_OMAP_H4
#include "board-h4.h"
-#error "Support for H4 board not yet implemented."
+#endif
+
+#ifdef CONFIG_MACH_OMAP_APOLLON
+#include "board-apollon.h"
#endif
#ifdef CONFIG_MACH_OMAP_OSK
#include "board-voiceblue.h"
#endif
-#ifdef CONFIG_MACH_NETSTAR
-#include "board-netstar.h"
-#endif
-
#endif /* !__ASSEMBLER__ */
#endif /* __ASM_ARCH_OMAP_HARDWARE_H */