+Kernel driver abituguru
+=======================
+
+Supported chips:
+ * Abit uGuru revision 1-3 (Hardware Monitor part only)
+ Prefix: 'abituguru'
+ Addresses scanned: ISA 0x0E0
+ Datasheet: Not available, this driver is based on reverse engineering.
+ A "Datasheet" has been written based on the reverse engineering it
+ should be available in the same dir as this file under the name
+ abituguru-datasheet.
+ Note:
+ The uGuru is a microcontroller with onboard firmware which programs
+ it to behave as a hwmon IC. There are many different revisions of the
+ firmware and thus effectivly many different revisions of the uGuru.
+ Below is an incomplete list with which revisions are used for which
+ Motherboards:
+ uGuru 1.00 ~ 1.24 (AI7, KV8-MAX3, AN7) (1)
+ uGuru 2.0.0.0 ~ 2.0.4.2 (KV8-PRO)
+ uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8)
+ uGuru 2.2.0.0 ~ 2.2.0.6 (AA8 Fatal1ty)
+ uGuru 2.3.0.0 ~ 2.3.0.9 (AN8)
+ uGuru 3.0.0.0 ~ 3.0.1.2 (AW8, AL8, NI8)
+ uGuru 4.xxxxx? (AT8 32X) (2)
+ 1) For revisions 2 and 3 uGuru's the driver can autodetect the
+ sensortype (Volt or Temp) for bank1 sensors, for revision 1 uGuru's
+ this doesnot always work. For these uGuru's the autodection can
+ be overriden with the bank1_types module param. For all 3 known
+ revison 1 motherboards the correct use of this param is:
+ bank1_types=1,1,0,0,0,0,0,2,0,0,0,0,2,0,0,1
+ You may also need to specify the fan_sensors option for these boards
+ fan_sensors=5
+ 2) The current version of the abituguru driver is known to NOT work
+ on these Motherboards
+
+Authors:
+ Hans de Goede <j.w.r.degoede@hhs.nl>,
+ (Initial reverse engineering done by Olle Sandberg
+ <ollebull@gmail.com>)
+
+
+Module Parameters
+-----------------
+
+* force: bool Force detection. Note this parameter only causes the
+ detection to be skipped, if the uGuru can't be read
+ the module initialization (insmod) will still fail.
+* bank1_types: int[] Bank1 sensortype autodetection override:
+ -1 autodetect (default)
+ 0 volt sensor
+ 1 temp sensor
+ 2 not connected
+* fan_sensors: int Tell the driver how many fan speed sensors there are
+ on your motherboard. Default: 0 (autodetect).
+* pwms: int Tell the driver how many fan speed controls (fan
+ pwms) your motherboard has. Default: 0 (autodetect).
+* verbose: int How verbose should the driver be? (0-3):
+ 0 normal output
+ 1 + verbose error reporting
+ 2 + sensors type probing info (default)
+ 3 + retryable error reporting
+ Default: 2 (the driver is still in the testing phase)
+
+Notice if you need any of the first three options above please insmod the
+driver with verbose set to 3 and mail me <j.w.r.degoede@hhs.nl> the output of:
+dmesg | grep abituguru
+
+
+Description
+-----------
+
+This driver supports the hardware monitoring features of the Abit uGuru chip
+found on Abit uGuru featuring motherboards (most modern Abit motherboards).
+
+The uGuru chip in reality is a Winbond W83L950D in disguise (despite Abit
+claiming it is "a new microprocessor designed by the ABIT Engineers").
+Unfortunatly this doesn't help since the W83L950D is a generic
+microcontroller with a custom Abit application running on it.
+
+Despite Abit not releasing any information regarding the uGuru, Olle
+Sandberg <ollebull@gmail.com> has managed to reverse engineer the sensor part
+of the uGuru. Without his work this driver would not have been possible.
+
+Known Issues
+------------
+
+The voltage and frequency control parts of the Abit uGuru are not supported.