datapath: omit _mod from module names

[sliver-openvswitch.git] / INSTALL.Linux

diff --git a/INSTALL.Linux b/INSTALL.Linux
index 8ef2315..c0b07d5 100644 (file)
--- a/INSTALL.Linux
+++ b/INSTALL.Linux
@@ -120,7 +120,7 @@ following software:
 You should ensure that /dev/urandom exists.  To support TAP devices,
 you must also ensure that /dev/net/tun exists.
 
 You should ensure that /dev/urandom exists.  To support TAP devices,
 you must also ensure that /dev/net/tun exists.
 

-To run the ovsdmonitor tool, the machine must also have the following
+To run the ovsdbmonitor tool, the machine must also have the following

 software:
 
     - Python 2.x, for x >= 4.
 software:
 
     - Python 2.x, for x >= 4.


@@ -194,16 +194,16 @@ Prerequisites section, follow the procedure below to build.
 
 6. If you built kernel modules, you may load them with "insmod", e.g.:
 
 
 6. If you built kernel modules, you may load them with "insmod", e.g.:
 

-      % insmod datapath/linux/openvswitch_mod.ko
+      % insmod datapath/linux/openvswitch.ko

 
    You may need to specify a full path to insmod, e.g. /sbin/insmod.
    To verify that the modules have been loaded, run "/sbin/lsmod" and
 
    You may need to specify a full path to insmod, e.g. /sbin/insmod.
    To verify that the modules have been loaded, run "/sbin/lsmod" and

-   check that openvswitch_mod is listed.
+   check that openvswitch is listed.

 
    If the "insmod" operation fails, look at the last few kernel log
    messages (e.g. with "dmesg | tail"):
 
 
    If the "insmod" operation fails, look at the last few kernel log
    messages (e.g. with "dmesg | tail"):
 

-      - The message "openvswitch_mod: exports duplicate symbol
+      - The message "openvswitch: exports duplicate symbol

         br_should_route_hook (owned by bridge)" means that the bridge
         module is loaded.  Run "/sbin/rmmod bridge" to remove it.
 
         br_should_route_hook (owned by bridge)" means that the bridge
         module is loaded.  Run "/sbin/rmmod bridge" to remove it.
 


@@ -212,7 +212,7 @@ Prerequisites section, follow the procedure below to build.
         the kernel, rather than as a module.  Open vSwitch does not
         support this configuration (see "Build Requirements", above).
 
         the kernel, rather than as a module.  Open vSwitch does not
         support this configuration (see "Build Requirements", above).
 

-      - The message "openvswitch_mod: exports duplicate symbol
+      - The message "openvswitch: exports duplicate symbol

         dp_ioctl_hook (owned by ofdatapath)" means that the ofdatapath
         module from the OpenFlow reference implementation is loaded.
         Run "/sbin/rmmod ofdatapath" to remove it.  (You might have to
         dp_ioctl_hook (owned by ofdatapath)" means that the ofdatapath
         module from the OpenFlow reference implementation is loaded.
         Run "/sbin/rmmod ofdatapath" to remove it.  (You might have to


@@ -222,10 +222,10 @@ Prerequisites section, follow the procedure below to build.
 
       - Otherwise, the most likely problem is that Open vSwitch was
         built for a kernel different from the one into which you are
 
       - Otherwise, the most likely problem is that Open vSwitch was
         built for a kernel different from the one into which you are

-        trying to load it.  Run "modinfo" on openvswitch_mod.ko and on
+        trying to load it.  Run "modinfo" on openvswitch.ko and on

         a module built for the running kernel, e.g.:
 
         a module built for the running kernel, e.g.:
 

-           % /sbin/modinfo openvswitch_mod.ko
+           % /sbin/modinfo openvswitch.ko

            % /sbin/modinfo /lib/modules/`uname -r`/kernel/net/bridge/bridge.ko
 
         Compare the "vermagic" lines output by the two commands.  If
            % /sbin/modinfo /lib/modules/`uname -r`/kernel/net/bridge/bridge.ko
 
         Compare the "vermagic" lines output by the two commands.  If


@@ -235,7 +235,7 @@ Prerequisites section, follow the procedure below to build.
         module loading, please include the output from the "dmesg" and
         "modinfo" commands mentioned above.
 
         module loading, please include the output from the "dmesg" and
         "modinfo" commands mentioned above.
 

-   There is an optional module parameter to openvswitch_mod.ko called
+   There is an optional module parameter to openvswitch.ko called

    vlan_tso that enables TCP segmentation offload over VLANs on NICs
    that support it. Many drivers do not expose support for TSO on VLANs
    in a way that Open vSwitch can use but there is no way to detect
    vlan_tso that enables TCP segmentation offload over VLANs on NICs
    that support it. Many drivers do not expose support for TSO on VLANs
    in a way that Open vSwitch can use but there is no way to detect