+static inline unsigned int omap_serial_in(struct plat_serial8250_port *up,
+ int offset)
+{
+ offset <<= up->regshift;
+ return (unsigned int)__raw_readb(up->membase + offset);
+}
+
+static inline void omap_serial_outp(struct plat_serial8250_port *p, int offset,
+ int value)
+{
+ offset <<= p->regshift;
+ __raw_writeb(value, p->membase + offset);
+}
+
+/*
+ * Internal UARTs need to be initialized for the 8250 autoconfig to work
+ * properly. Note that the TX watermark initialization may not be needed
+ * once the 8250.c watermark handling code is merged.
+ */
+static void __init omap_serial_reset(struct plat_serial8250_port *p)
+{
+ omap_serial_outp(p, UART_OMAP_MDR1, 0x07); /* disable UART */
+ omap_serial_outp(p, UART_OMAP_SCR, 0x08); /* TX watermark */
+ omap_serial_outp(p, UART_OMAP_MDR1, 0x00); /* enable UART */
+
+ if (!cpu_is_omap1510()) {
+ omap_serial_outp(p, UART_OMAP_SYSC, 0x01);
+ while (!(omap_serial_in(p, UART_OMAP_SYSC) & 0x01));
+ }
+}
+
+static struct plat_serial8250_port serial_platform_data[] = {
+ {
+ .membase = (char*)IO_ADDRESS(OMAP_UART1_BASE),
+ .mapbase = (unsigned long)OMAP_UART1_BASE,
+ .irq = INT_UART1,
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = OMAP16XX_BASE_BAUD * 16,
+ },
+ {
+ .membase = (char*)IO_ADDRESS(OMAP_UART2_BASE),
+ .mapbase = (unsigned long)OMAP_UART2_BASE,
+ .irq = INT_UART2,
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = OMAP16XX_BASE_BAUD * 16,
+ },
+ {
+ .membase = (char*)IO_ADDRESS(OMAP_UART3_BASE),
+ .mapbase = (unsigned long)OMAP_UART3_BASE,
+ .irq = INT_UART3,
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = OMAP16XX_BASE_BAUD * 16,
+ },
+ { },
+};
+
+static struct platform_device serial_device = {
+ .name = "serial8250",
+ .id = 0,
+ .dev = {
+ .platform_data = serial_platform_data,
+ },
+};
+
+/*
+ * Note that on Innovator-1510 UART2 pins conflict with USB2.
+ * By default UART2 does not work on Innovator-1510 if you have
+ * USB OHCI enabled. To use UART2, you must disable USB2 first.
+ */
+void __init omap_serial_init(int ports[OMAP_MAX_NR_PORTS])
+{
+ int i;
+
+ if (cpu_is_omap730()) {
+ serial_platform_data[0].regshift = 0;
+ serial_platform_data[1].regshift = 0;
+ serial_platform_data[0].irq = INT_730_UART_MODEM_1;
+ serial_platform_data[1].irq = INT_730_UART_MODEM_IRDA_2;
+ }
+
+ if (cpu_is_omap1510()) {
+ serial_platform_data[0].uartclk = OMAP1510_BASE_BAUD * 16;
+ serial_platform_data[1].uartclk = OMAP1510_BASE_BAUD * 16;
+ serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16;
+ }
+
+ for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
+ unsigned char reg;
+
+ if (ports[i] == 0) {
+ serial_platform_data[i].membase = 0;
+ serial_platform_data[i].mapbase = 0;
+ continue;
+ }
+
+ switch (i) {
+ case 0:
+ if (cpu_is_omap1510()) {
+ omap_cfg_reg(UART1_TX);
+ omap_cfg_reg(UART1_RTS);
+ if (machine_is_omap_innovator()) {
+ reg = fpga_read(OMAP1510_FPGA_POWER);
+ reg |= OMAP1510_FPGA_PCR_COM1_EN;
+ fpga_write(reg, OMAP1510_FPGA_POWER);
+ udelay(10);
+ }
+ }
+ break;
+ case 1:
+ if (cpu_is_omap1510()) {
+ omap_cfg_reg(UART2_TX);
+ omap_cfg_reg(UART2_RTS);
+ if (machine_is_omap_innovator()) {
+ reg = fpga_read(OMAP1510_FPGA_POWER);
+ reg |= OMAP1510_FPGA_PCR_COM2_EN;
+ fpga_write(reg, OMAP1510_FPGA_POWER);
+ udelay(10);
+ }
+ }
+ break;
+ case 2:
+ if (cpu_is_omap1510()) {
+ omap_cfg_reg(UART3_TX);
+ omap_cfg_reg(UART3_RX);
+ }
+ break;
+ }
+ omap_serial_reset(&serial_platform_data[i]);
+ }
+}
+
+static int __init omap_init(void)
+{
+ return platform_device_register(&serial_device);
+}
+arch_initcall(omap_init);
+
+#define NO_LENGTH_CHECK 0xffffffff
+