+config CPU_S3C2410
+ bool
+ depends on ARCH_S3C2410
+ help
+ Support for S3C2410 and S3C2410A family from the S3C24XX line
+ of Samsung Mobile CPUs.
+
+config CPU_S3C2440
+ bool
+ depends on ARCH_S3C2410
+ help
+ Support for S3C2440 Samsung Mobile CPU based systems.
+
+comment "S3C2410 Boot"
+
+config S3C2410_BOOT_WATCHDOG
+ bool "S3C2410 Initialisation watchdog"
+ depends on ARCH_S3C2410 && S3C2410_WATCHDOG
+ help
+ Say y to enable the watchdog during the kernel decompression
+ stage. If the kernel fails to uncompress, then the watchdog
+ will trigger a reset and the system should restart.
+
+ Although this uses the same hardware unit as the kernel watchdog
+ driver, it is not a replacement for it. If you use this option,
+ you will have to use the watchdg driver to either stop the timeout
+ or restart it. If you do not, then your kernel will reboot after
+ startup.
+
+ The driver uses a fixed timeout value, so the exact time till the
+ system resets depends on the value of PCLK. The timeout on an
+ 200MHz s3c2410 should be about 30 seconds.
+
+config S3C2410_BOOT_ERROR_RESET
+ bool "S3C2410 Reboot on decompression error"
+ depends on ARCH_S3C2410
+ help
+ Say y here to use the watchdog to reset the system if the
+ kernel decompressor detects an error during decompression.
+
+
+comment "S3C2410 Setup"
+
+config S3C2410_DMA
+ bool "S3C2410 DMA support"
+ depends on ARCH_S3C2410
+ help
+ S3C2410 DMA support. This is needed for drivers like sound which
+ use the S3C2410's DMA system to move data to and from the
+ peripheral blocks.
+
+config S3C2410_DMA_DEBUG
+ bool "S3C2410 DMA support debug"
+ depends on ARCH_S3C2410 && S3C2410_DMA
+ help
+ Enable debugging output for the DMA code. This option sends info
+ to the kernel log, at priority KERN_DEBUG.
+
+ Note, it is easy to create and fill the log buffer in a small
+ amount of time, as well as using an significant percentage of
+ the CPU time doing so.
+
+
+config S3C2410_PM_DEBUG
+ bool "S3C2410 PM Suspend debug"
+ depends on ARCH_S3C2410 && PM
+ help
+ Say Y here if you want verbose debugging from the PM Suspend and
+ Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
+ for more information.
+
+config S3C2410_PM_CHECK
+ bool "S3C2410 PM Suspend Memory CRC"
+ depends on ARCH_S3C2410 && PM && CRC32
+ help
+ Enable the PM code's memory area checksum over sleep. This option
+ will generate CRCs of all blocks of memory, and store them before
+ going to sleep. The blocks are then checked on resume for any
+ errors.
+
+config S3C2410_PM_CHECK_CHUNKSIZE
+ int "S3C2410 PM Suspend CRC Chunksize (KiB)"
+ depends on ARCH_S3C2410 && PM && S3C2410_PM_CHECK
+ default 64
+ help
+ Set the chunksize in Kilobytes of the CRC for checking memory
+ corruption over suspend and resume. A smaller value will mean that
+ the CRC data block will take more memory, but wil identify any
+ faults with better precision.
+
+config PM_SIMTEC
+ bool
+ depends on PM && (ARCH_BAST || MACH_VR1000)
+ default y
+
+config S3C2410_LOWLEVEL_UART_PORT
+ int "S3C2410 UART to use for low-level messages"
+ default 0
+ help
+ Choice of which UART port to use for the low-level messages,
+ such as the `Uncompressing...` at start time. The value of
+ this configuration should be between zero and two. The port
+ must have been initialised by the boot-loader before use.
+
+ Note, this does not affect the port used by the debug messages,
+ which is a separate configuration.
+