+
+ installfailed = """
+Once the node meets these requirements, please reinitiate the install
+by visiting:
+
+https://%(PLC_WWW_HOST)s:%(PLC_WWW_SSL_PORT)d/db/nodes/?id=%(node_id)d
+
+Click the Reinstall link, then reboot the node.
+
+If you have already performed this step and are still receiving this
+message, please reply so that we may investigate the problem.
+"""
+
+ # Load default message templates
+ message_templates = [
+ {'message_id': 'Verify account',
+ 'subject': "Verify account registration",
+ 'template': """
+Please verify that you registered for a %(PLC_NAME)s account with the
+username %(email)s by visiting:
+
+https://%(PLC_WWW_HOST)s:%(PLC_WWW_SSL_PORT)d/db/persons/register.php?id=%(person_id)d&key=%(verification_key)s
+
+If you did not register for a %(PLC_NAME)s account, please ignore this
+message, or contact %(PLC_NAME)s Support <%(PLC_MAIL_SUPPORT_ADDRESS)s>.
+"""
+ },
+
+ {'message_id': 'New PI account',
+ 'subject': "New PI account registration from %(first_name)s %(last_name)s <%(email)s> at %(site_name)s",
+ 'template': """
+%(first_name)s %(last_name)s <%(email)s> has signed up for a new
+%(PLC_NAME)s account at %(site_name)s and has requested a PI role. PIs
+are responsible for enabling user accounts, creating slices, and
+ensuring that all users abide by the %(PLC_NAME)s Acceptable Use
+Policy.
+
+Only %(PLC_NAME)s administrators may enable new PI accounts. If you
+are a PI at %(site_name)s, please respond and indicate whether this
+registration is acceptable.
+
+To view the request, visit:
+
+https://%(PLC_WWW_HOST)s:%(PLC_WWW_SSL_PORT)d/db/persons/index.php?id=%(person_id)d
+"""
+ },
+
+ {'message_id': 'New account',
+ 'subject': "New account registration from %(first_name)s %(last_name)s <%(email)s> at %(site_name)s",
+ 'template': """
+%(first_name)s %(last_name)s <%(email)s> has signed up for a new
+%(PLC_NAME)s account at %(site_name)s and has requested the following
+roles: %(roles)s.
+
+To deny the request or enable the account, visit:
+
+https://%(PLC_WWW_HOST)s:%(PLC_WWW_SSL_PORT)d/db/persons/index.php?id=%(person_id)d
+"""
+ },
+
+ {'message_id': 'Password reset requested',
+ 'subject': "Password reset requested",
+ 'template': """
+Someone has requested that the password of your %(PLC_NAME)s account
+%(email)s be reset. If this person was you, you may continue with the
+reset by visiting:
+
+https://%(PLC_WWW_HOST)s:%(PLC_WWW_SSL_PORT)d/db/persons/reset_password.php?id=%(person_id)d&key=%(verification_key)s
+
+If you did not request that your password be reset, please contact
+%(PLC_NAME)s Support <%(PLC_MAIL_SUPPORT_ADDRESS)s>. Do not quote or
+otherwise include any of this text in any correspondence.
+"""
+ },
+
+ {'message_id': 'Password reset',
+ 'subject': "Password reset",
+ 'template': """
+The password of your %(PLC_NAME)s account %(email)s has been
+temporarily reset to:
+
+%(password)s
+
+Please change it at as soon as possible by visiting:
+
+https://%(PLC_WWW_HOST)s:%(PLC_WWW_SSL_PORT)d/db/persons/index.php?id=%(person_id)d
+
+If you did not request that your password be reset, please contact
+%(PLC_NAME)s Support <%(PLC_MAIL_SUPPORT_ADDRESS)s>. Do not quote or
+otherwise include any of this text in any correspondence.
+"""
+ },
+
+ # Boot Manager messages
+ {'message_id': "installfinished",
+ 'subject': "%(hostname)s completed installation",
+ 'template': """
+%(hostname)s just completed installation.
+
+The node should be usable in a couple of minutes if installation was
+successful.
+"""
+ },
+
+ {'message_id': "insufficientdisk",
+ 'subject': "%(hostname)s does not have sufficient disk space",
+ 'template': """
+%(hostname)s failed to boot because it does not have sufficent disk
+space, or because its disk controller was not recognized.
+
+Please replace the current disk or disk controller or install
+additional disks to meet the current hardware requirements.
+""" + installfailed
+ },
+
+ {'message_id': "insufficientmemory",
+ 'subject': "%(hostname)s does not have sufficient memory",
+ 'template': """
+%(hostname)s failed to boot because it does not have sufficent
+memory.
+
+Please install additional memory to meet the current hardware
+requirements.
+""" + installfailed
+ },
+
+ {'message_id': "authfail",
+ 'subject': "%(hostname)s failed to authenticate",
+ 'template':
+"""
+%(hostname)s failed to authenticate for the following reason:
+
+%(fault)s
+
+The most common reason for authentication failure is that the
+authentication key stored in the node configuration file, does not
+match the key on record. Regenerate the node configuration file by
+visiting:
+
+https://%(PLC_WWW_HOST)s:%(PLC_WWW_SSL_PORT)d/db/nodes/?id=%(node_id)d
+
+Click the Configuration File link, and save the downloaded file as
+plnode.txt on either a floppy disk or a USB flash drive. Click the
+Boot link, then reboot the node.
+
+If you have already performed this step and are still receiving this
+message, please reply so that we may investigate the problem.
+"""
+ },
+
+ {'message_id': "notinstalled",
+ 'subject': "%(hostname)s is not installed",
+ 'template':
+"""
+%(hostname)s failed to boot because it has either never been
+installed, or the installation is corrupt.
+
+Please check if the hard drive has failed, and replace it if so. After
+doing so, visit:
+
+https://%(PLC_WWW_HOST)s:%(PLC_WWW_SSL_PORT)d/db/nodes/?id=%(node_id)d
+
+Click the Reinstall link, then reboot the node.
+
+If you have already performed this step and are still receiving this
+message, please reply so that we may investigate the problem.
+"""
+ },
+
+ {'message_id': "hostnamenotresolve",
+ 'subject': "%(hostname)s does not resolve",
+ 'template':
+"""
+%(hostname)s failed to boot because its hostname does not resolve, or
+does resolve but does not match its configured IP address.
+
+Please check the network settings for the node, especially its
+hostname, IP address, and DNS servers, by visiting:
+
+https://%(PLC_WWW_HOST)s:%(PLC_WWW_SSL_PORT)d/db/nodes/?id=%(node_id)d
+
+Correct any errors, click the Reinstall link, then reboot the node.
+
+If you have already performed this step and are still receiving this
+message, please reply so that we may investigate the problem.
+"""
+ },
+
+ # XXX N.B. I don't think these are necessary, since there's no
+ # way that the Boot Manager would even be able to contact the
+ # API to send these messages.
+
+ {'message_id': "noconfig",
+ 'subject': "%(hostname)s does not have a configuration file",
+ 'template': """
+%(hostname)s failed to boot because it could not find a PlanetLab
+configuration file. To create this file, visit:
+
+https://%(PLC_WWW_HOST)s:%(PLC_WWW_SSL_PORT)d/db/nodes/?id=%(node_id)d
+
+Click the Configuration File link, and save the downloaded file as
+plnode.txt on either a floppy disk or a USB flash drive. Click the
+Reinstall link, then reboot the node.
+
+If you have already performed this step and are still receiving this
+message, please reply so that we may investigate the problem.
+"""
+ },
+
+ {'message_id': "nodetectednetwork",
+ 'subject': "%(hostname)s has unsupported network hardware",
+ 'template':
+"""
+
+%(hostname)s failed to boot because it has network hardware that is
+unsupported by the current production kernel. If it has booted
+successfully in the past, please try re-installing it by visiting:
+
+https://%(PLC_WWW_HOST)s:%(PLC_WWW_SSL_PORT)d/db/nodes/?id=%(node_id)d
+
+Click the Reinstall link, then reboot the node.
+
+If you have already performed this step and are still receiving this
+message, please reply so that we may investigate the problem.
+"""
+ },
+ ]
+
+ for template in message_templates:
+ messages = GetMessages([template['message_id']])
+ if not messages:
+ AddMessage(template)