-#define GG82563_E_PHY_ID 0x01410CA0
-
-
-/* Bits...
- * 15-5: page
- * 4-0: register offset
- */
-#define PHY_PAGE_SHIFT 5
-#define PHY_REG(page, reg) \
- (((page) << PHY_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
-
-#define IGP3_PHY_PORT_CTRL \
- PHY_REG(769, 17) /* Port General Configuration */
-#define IGP3_PHY_RATE_ADAPT_CTRL \
- PHY_REG(769, 25) /* Rate Adapter Control Register */
-
-#define IGP3_KMRN_FIFO_CTRL_STATS \
- PHY_REG(770, 16) /* KMRN FIFO's control/status register */
-#define IGP3_KMRN_POWER_MNG_CTRL \
- PHY_REG(770, 17) /* KMRN Power Management Control Register */
-#define IGP3_KMRN_INBAND_CTRL \
- PHY_REG(770, 18) /* KMRN Inband Control Register */
-#define IGP3_KMRN_DIAG \
- PHY_REG(770, 19) /* KMRN Diagnostic register */
-#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 /* RX PCS is not synced */
-#define IGP3_KMRN_ACK_TIMEOUT \
- PHY_REG(770, 20) /* KMRN Acknowledge Timeouts register */
-
-#define IGP3_VR_CTRL \
- PHY_REG(776, 18) /* Voltage regulator control register */
-#define IGP3_VR_CTRL_MODE_SHUT 0x0200 /* Enter powerdown, shutdown VRs */
-
-#define IGP3_CAPABILITY \
- PHY_REG(776, 19) /* IGP3 Capability Register */
-
-/* Capabilities for SKU Control */
-#define IGP3_CAP_INITIATE_TEAM 0x0001 /* Able to initiate a team */
-#define IGP3_CAP_WFM 0x0002 /* Support WoL and PXE */
-#define IGP3_CAP_ASF 0x0004 /* Support ASF */
-#define IGP3_CAP_LPLU 0x0008 /* Support Low Power Link Up */
-#define IGP3_CAP_DC_AUTO_SPEED 0x0010 /* Support AC/DC Auto Link Speed */
-#define IGP3_CAP_SPD 0x0020 /* Support Smart Power Down */
-#define IGP3_CAP_MULT_QUEUE 0x0040 /* Support 2 tx & 2 rx queues */
-#define IGP3_CAP_RSS 0x0080 /* Support RSS */
-#define IGP3_CAP_8021PQ 0x0100 /* Support 802.1Q & 802.1p */
-#define IGP3_CAP_AMT_CB 0x0200 /* Support active manageability and circuit breaker */
-
-#define IGP3_PPC_JORDAN_EN 0x0001
-#define IGP3_PPC_JORDAN_GIGA_SPEED 0x0002
-
-#define IGP3_KMRN_PMC_EE_IDLE_LINK_DIS 0x0001
-#define IGP3_KMRN_PMC_K0S_ENTRY_LATENCY_MASK 0x001E
-#define IGP3_KMRN_PMC_K0S_MODE1_EN_GIGA 0x0020
-#define IGP3_KMRN_PMC_K0S_MODE1_EN_100 0x0040
-
-#define IGP3E1000_PHY_MISC_CTRL 0x1B /* Misc. Ctrl register */
-#define IGP3_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Duplex Manual Set */
-
-#define IGP3_KMRN_EXT_CTRL PHY_REG(770, 18)
-#define IGP3_KMRN_EC_DIS_INBAND 0x0080
-
-#define IGP03E1000_E_PHY_ID 0x02A80390
-#define IFE_E_PHY_ID 0x02A80330 /* 10/100 PHY */
-#define IFE_PLUS_E_PHY_ID 0x02A80320
-#define IFE_C_E_PHY_ID 0x02A80310
-
-#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 /* 100BaseTx Extended Status, Control and Address */
-#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY special control register */
-#define IFE_PHY_RCV_FALSE_CARRIER 0x13 /* 100BaseTx Receive False Carrier Counter */
-#define IFE_PHY_RCV_DISCONNECT 0x14 /* 100BaseTx Receive Disconnet Counter */
-#define IFE_PHY_RCV_ERROT_FRAME 0x15 /* 100BaseTx Receive Error Frame Counter */
-#define IFE_PHY_RCV_SYMBOL_ERR 0x16 /* Receive Symbol Error Counter */
-#define IFE_PHY_PREM_EOF_ERR 0x17 /* 100BaseTx Receive Premature End Of Frame Error Counter */
-#define IFE_PHY_RCV_EOF_ERR 0x18 /* 10BaseT Receive End Of Frame Error Counter */
-#define IFE_PHY_TX_JABBER_DETECT 0x19 /* 10BaseT Transmit Jabber Detect Counter */
-#define IFE_PHY_EQUALIZER 0x1A /* PHY Equalizer Control and Status */
-#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY special control and LED configuration */
-#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control register */
-#define IFE_PHY_HWI_CONTROL 0x1D /* Hardware Integrity Control (HWI) */
-
-#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE 0x2000 /* Defaut 1 = Disable auto reduced power down */
-#define IFE_PESC_100BTX_POWER_DOWN 0x0400 /* Indicates the power state of 100BASE-TX */
-#define IFE_PESC_10BTX_POWER_DOWN 0x0200 /* Indicates the power state of 10BASE-T */
-#define IFE_PESC_POLARITY_REVERSED 0x0100 /* Indicates 10BASE-T polarity */
-#define IFE_PESC_PHY_ADDR_MASK 0x007C /* Bit 6:2 for sampled PHY address */
-#define IFE_PESC_SPEED 0x0002 /* Auto-negotiation speed result 1=100Mbs, 0=10Mbs */
-#define IFE_PESC_DUPLEX 0x0001 /* Auto-negotiation duplex result 1=Full, 0=Half */
-#define IFE_PESC_POLARITY_REVERSED_SHIFT 8
-
-#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 /* 1 = Dyanmic Power Down disabled */
-#define IFE_PSC_FORCE_POLARITY 0x0020 /* 1=Reversed Polarity, 0=Normal */
-#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 /* 1=Auto Polarity Disabled, 0=Enabled */
-#define IFE_PSC_JABBER_FUNC_DISABLE 0x0001 /* 1=Jabber Disabled, 0=Normal Jabber Operation */
-#define IFE_PSC_FORCE_POLARITY_SHIFT 5
-#define IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT 4
-
-#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable MDI/MDI-X feature, default 0=disabled */
-#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDIX-X, 0=force MDI */
-#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */
-#define IFE_PMC_AUTO_MDIX_COMPLETE 0x0010 /* Resolution algorthm is completed */
-#define IFE_PMC_MDIX_MODE_SHIFT 6
-#define IFE_PHC_MDIX_RESET_ALL_MASK 0x0000 /* Disable auto MDI-X */
-
-#define IFE_PHC_HWI_ENABLE 0x8000 /* Enable the HWI feature */
-#define IFE_PHC_ABILITY_CHECK 0x4000 /* 1= Test Passed, 0=failed */
-#define IFE_PHC_TEST_EXEC 0x2000 /* PHY launch test pulses on the wire */
-#define IFE_PHC_HIGHZ 0x0200 /* 1 = Open Circuit */
-#define IFE_PHC_LOWZ 0x0400 /* 1 = Short Circuit */
-#define IFE_PHC_LOW_HIGH_Z_MASK 0x0600 /* Mask for indication type of problem on the line */
-#define IFE_PHC_DISTANCE_MASK 0x01FF /* Mask for distance to the cable problem, in 80cm granularity */
-#define IFE_PHC_RESET_ALL_MASK 0x0000 /* Disable HWI */
-#define IFE_PSCL_PROBE_MODE 0x0020 /* LED Probe mode */
-#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */
-#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */
-
-#define ICH8_FLASH_COMMAND_TIMEOUT 500 /* 500 ms , should be adjusted */
-#define ICH8_FLASH_CYCLE_REPEAT_COUNT 10 /* 10 cycles , should be adjusted */
-#define ICH8_FLASH_SEG_SIZE_256 256
-#define ICH8_FLASH_SEG_SIZE_4K 4096
-#define ICH8_FLASH_SEG_SIZE_64K 65536
-
-#define ICH8_CYCLE_READ 0x0
-#define ICH8_CYCLE_RESERVED 0x1
-#define ICH8_CYCLE_WRITE 0x2
-#define ICH8_CYCLE_ERASE 0x3
-
-#define ICH8_FLASH_GFPREG 0x0000
-#define ICH8_FLASH_HSFSTS 0x0004
-#define ICH8_FLASH_HSFCTL 0x0006
-#define ICH8_FLASH_FADDR 0x0008
-#define ICH8_FLASH_FDATA0 0x0010
-#define ICH8_FLASH_FRACC 0x0050
-#define ICH8_FLASH_FREG0 0x0054
-#define ICH8_FLASH_FREG1 0x0058
-#define ICH8_FLASH_FREG2 0x005C
-#define ICH8_FLASH_FREG3 0x0060
-#define ICH8_FLASH_FPR0 0x0074
-#define ICH8_FLASH_FPR1 0x0078
-#define ICH8_FLASH_SSFSTS 0x0090
-#define ICH8_FLASH_SSFCTL 0x0092
-#define ICH8_FLASH_PREOP 0x0094
-#define ICH8_FLASH_OPTYPE 0x0096
-#define ICH8_FLASH_OPMENU 0x0098
-
-#define ICH8_FLASH_REG_MAPSIZE 0x00A0
-#define ICH8_FLASH_SECTOR_SIZE 4096
-#define ICH8_GFPREG_BASE_MASK 0x1FFF
-#define ICH8_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
-
-/* ICH8 GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
-/* Offset 04h HSFSTS */
-union ich8_hws_flash_status {
- struct ich8_hsfsts {
-#ifdef E1000_BIG_ENDIAN
- uint16_t reserved2 :6;
- uint16_t fldesvalid :1;
- uint16_t flockdn :1;
- uint16_t flcdone :1;
- uint16_t flcerr :1;
- uint16_t dael :1;
- uint16_t berasesz :2;
- uint16_t flcinprog :1;
- uint16_t reserved1 :2;
-#else
- uint16_t flcdone :1; /* bit 0 Flash Cycle Done */
- uint16_t flcerr :1; /* bit 1 Flash Cycle Error */
- uint16_t dael :1; /* bit 2 Direct Access error Log */
- uint16_t berasesz :2; /* bit 4:3 Block/Sector Erase Size */
- uint16_t flcinprog :1; /* bit 5 flash SPI cycle in Progress */
- uint16_t reserved1 :2; /* bit 13:6 Reserved */
- uint16_t reserved2 :6; /* bit 13:6 Reserved */
- uint16_t fldesvalid :1; /* bit 14 Flash Descriptor Valid */
- uint16_t flockdn :1; /* bit 15 Flash Configuration Lock-Down */
-#endif
- } hsf_status;
- uint16_t regval;
-};
-
-/* ICH8 GbE Flash Hardware Sequencing Flash control Register bit breakdown */
-/* Offset 06h FLCTL */
-union ich8_hws_flash_ctrl {
- struct ich8_hsflctl {
-#ifdef E1000_BIG_ENDIAN
- uint16_t fldbcount :2;
- uint16_t flockdn :6;
- uint16_t flcgo :1;
- uint16_t flcycle :2;
- uint16_t reserved :5;
-#else
- uint16_t flcgo :1; /* 0 Flash Cycle Go */
- uint16_t flcycle :2; /* 2:1 Flash Cycle */
- uint16_t reserved :5; /* 7:3 Reserved */
- uint16_t fldbcount :2; /* 9:8 Flash Data Byte Count */
- uint16_t flockdn :6; /* 15:10 Reserved */
-#endif
- } hsf_ctrl;
- uint16_t regval;
-};
-
-/* ICH8 Flash Region Access Permissions */
-union ich8_hws_flash_regacc {
- struct ich8_flracc {
-#ifdef E1000_BIG_ENDIAN
- uint32_t gmwag :8;
- uint32_t gmrag :8;
- uint32_t grwa :8;
- uint32_t grra :8;
-#else
- uint32_t grra :8; /* 0:7 GbE region Read Access */
- uint32_t grwa :8; /* 8:15 GbE region Write Access */
- uint32_t gmrag :8; /* 23:16 GbE Master Read Access Grant */
- uint32_t gmwag :8; /* 31:24 GbE Master Write Access Grant */
-#endif
- } hsf_flregacc;
- uint16_t regval;
-};