-/*
- * Look for some specific subsystem setups that need
- * pre-configuration not properly done by the BIOS (especially laptops)
- * This code is based in part on smcinit.c, tosh1800-smcinit.c
- * and tosh2450-smcinit.c. The table lists the device entries
- * for ISA bridges with an LPC (Low Pin Count) controller which
- * handles the communication with the SMSC device. After the LPC
- * controller is initialized through PCI, the SMSC device is initialized
- * through a dedicated port in the ISA port-mapped I/O area, this latter
- * area is used to configure the SMSC device with default
- * SIR and FIR I/O ports, DMA and IRQ. Different vendors have
- * used different sets of parameters and different control port
- * addresses making a subsystem device table necessary.
- */
-#ifdef CONFIG_PCI
-#define PCIID_VENDOR_INTEL 0x8086
-#define PCIID_VENDOR_ALI 0x10b9
-static struct smsc_ircc_subsystem_configuration subsystem_configurations[] __devinitdata = {
- {
- .vendor = PCIID_VENDOR_INTEL, /* Intel 82801DBM LPC bridge */
- .device = 0x24cc,
- .subvendor = 0x103c,
- .subdevice = 0x088c,
- /* Quite certain these are the same for nc8000 as for nc6000 */
- .sir_io = 0x02f8,
- .fir_io = 0x0130,
- .fir_irq = 0x05,
- .fir_dma = 0x03,
- .cfg_base = 0x004e,
- .preconfigure = preconfigure_through_82801,
- .name = "HP nc8000",
- },
- {
- .vendor = PCIID_VENDOR_INTEL, /* Intel 82801DBM LPC bridge */
- .device = 0x24cc,
- .subvendor = 0x103c,
- .subdevice = 0x0890,
- .sir_io = 0x02f8,
- .fir_io = 0x0130,
- .fir_irq = 0x05,
- .fir_dma = 0x03,
- .cfg_base = 0x004e,
- .preconfigure = preconfigure_through_82801,
- .name = "HP nc6000",
- },
- {
- /* Intel 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge */
- .vendor = PCIID_VENDOR_INTEL,
- .device = 0x24c0,
- .subvendor = 0x1179,
- .subdevice = 0xffff, /* 0xffff is "any" */
- .sir_io = 0x03f8,
- .fir_io = 0x0130,
- .fir_irq = 0x07,
- .fir_dma = 0x01,
- .cfg_base = 0x002e,
- .preconfigure = preconfigure_through_82801,
- .name = "Toshiba laptop with Intel 82801DB/DBL LPC bridge",
- },
- {
- .vendor = PCIID_VENDOR_INTEL, /* Intel 82801CAM ISA bridge */
- .device = 0x248c,
- .subvendor = 0x1179,
- .subdevice = 0xffff, /* 0xffff is "any" */
- .sir_io = 0x03f8,
- .fir_io = 0x0130,
- .fir_irq = 0x03,
- .fir_dma = 0x03,
- .cfg_base = 0x002e,
- .preconfigure = preconfigure_through_82801,
- .name = "Toshiba laptop with Intel 82801CAM ISA bridge",
- },
- {
- /* 82801DBM (ICH4-M) LPC Interface Bridge */
- .vendor = PCIID_VENDOR_INTEL,
- .device = 0x24cc,
- .subvendor = 0x1179,
- .subdevice = 0xffff, /* 0xffff is "any" */
- .sir_io = 0x03f8,
- .fir_io = 0x0130,
- .fir_irq = 0x03,
- .fir_dma = 0x03,
- .cfg_base = 0x002e,
- .preconfigure = preconfigure_through_82801,
- .name = "Toshiba laptop with Intel 8281DBM LPC bridge",
- },
- {
- /* ALi M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+] */
- .vendor = PCIID_VENDOR_ALI,
- .device = 0x1533,
- .subvendor = 0x1179,
- .subdevice = 0xffff, /* 0xffff is "any" */
- .sir_io = 0x02e8,
- .fir_io = 0x02f8,
- .fir_irq = 0x07,
- .fir_dma = 0x03,
- .cfg_base = 0x002e,
- .preconfigure = preconfigure_through_ali,
- .name = "Toshiba laptop with ALi ISA bridge",
- },
- { } // Terminator
-};
-
-
-/*
- * This sets up the basic SMSC parameters
- * (FIR port, SIR port, FIR DMA, FIR IRQ)
- * through the chip configuration port.
- */
-static int __init preconfigure_smsc_chip(struct
- smsc_ircc_subsystem_configuration
- *conf)
-{
- unsigned short iobase = conf->cfg_base;
- unsigned char tmpbyte;
-
- outb(LPC47N227_CFGACCESSKEY, iobase); // enter configuration state
- outb(SMSCSIOFLAT_DEVICEID_REG, iobase); // set for device ID
- tmpbyte = inb(iobase +1); // Read device ID
- IRDA_DEBUG(0,
- "Detected Chip id: 0x%02x, setting up registers...\n",
- tmpbyte);
-
- /* Disable UART1 and set up SIR I/O port */
- outb(0x24, iobase); // select CR24 - UART1 base addr
- outb(0x00, iobase + 1); // disable UART1
- outb(SMSCSIOFLAT_UART2BASEADDR_REG, iobase); // select CR25 - UART2 base addr
- outb( (conf->sir_io >> 2), iobase + 1); // bits 2-9 of 0x3f8
- tmpbyte = inb(iobase + 1);
- if (tmpbyte != (conf->sir_io >> 2) ) {
- IRDA_WARNING("ERROR: could not configure SIR ioport.\n");
- IRDA_WARNING("Try to supply ircc_cfg argument.\n");
- return -ENXIO;
- }
-
- /* Set up FIR IRQ channel for UART2 */
- outb(SMSCSIOFLAT_UARTIRQSELECT_REG, iobase); // select CR28 - UART1,2 IRQ select
- tmpbyte = inb(iobase + 1);
- tmpbyte &= SMSCSIOFLAT_UART1IRQSELECT_MASK; // Do not touch the UART1 portion
- tmpbyte |= (conf->fir_irq & SMSCSIOFLAT_UART2IRQSELECT_MASK);
- outb(tmpbyte, iobase + 1);
- tmpbyte = inb(iobase + 1) & SMSCSIOFLAT_UART2IRQSELECT_MASK;
- if (tmpbyte != conf->fir_irq) {
- IRDA_WARNING("ERROR: could not configure FIR IRQ channel.\n");
- return -ENXIO;
- }
-
- /* Set up FIR I/O port */
- outb(SMSCSIOFLAT_FIRBASEADDR_REG, iobase); // CR2B - SCE (FIR) base addr
- outb((conf->fir_io >> 3), iobase + 1);
- tmpbyte = inb(iobase + 1);
- if (tmpbyte != (conf->fir_io >> 3) ) {
- IRDA_WARNING("ERROR: could not configure FIR I/O port.\n");
- return -ENXIO;
- }
-
- /* Set up FIR DMA channel */
- outb(SMSCSIOFLAT_FIRDMASELECT_REG, iobase); // CR2C - SCE (FIR) DMA select
- outb((conf->fir_dma & LPC47N227_FIRDMASELECT_MASK), iobase + 1); // DMA
- tmpbyte = inb(iobase + 1) & LPC47N227_FIRDMASELECT_MASK;
- if (tmpbyte != (conf->fir_dma & LPC47N227_FIRDMASELECT_MASK)) {
- IRDA_WARNING("ERROR: could not configure FIR DMA channel.\n");
- return -ENXIO;
- }
-
- outb(SMSCSIOFLAT_UARTMODE0C_REG, iobase); // CR0C - UART mode
- tmpbyte = inb(iobase + 1);
- tmpbyte &= ~SMSCSIOFLAT_UART2MODE_MASK |
- SMSCSIOFLAT_UART2MODE_VAL_IRDA;
- outb(tmpbyte, iobase + 1); // enable IrDA (HPSIR) mode, high speed
-
- outb(LPC47N227_APMBOOTDRIVE_REG, iobase); // CR07 - Auto Pwr Mgt/boot drive sel
- tmpbyte = inb(iobase + 1);
- outb(tmpbyte | LPC47N227_UART2AUTOPWRDOWN_MASK, iobase + 1); // enable UART2 autopower down
-
- /* This one was not part of tosh1800 */
- outb(0x0a, iobase); // CR0a - ecp fifo / ir mux
- tmpbyte = inb(iobase + 1);
- outb(tmpbyte | 0x40, iobase + 1); // send active device to ir port
-
- outb(LPC47N227_UART12POWER_REG, iobase); // CR02 - UART 1,2 power
- tmpbyte = inb(iobase + 1);
- outb(tmpbyte | LPC47N227_UART2POWERDOWN_MASK, iobase + 1); // UART2 power up mode, UART1 power down
-
- outb(LPC47N227_FDCPOWERVALIDCONF_REG, iobase); // CR00 - FDC Power/valid config cycle
- tmpbyte = inb(iobase + 1);
- outb(tmpbyte | LPC47N227_VALID_MASK, iobase + 1); // valid config cycle done
-
- outb(LPC47N227_CFGEXITKEY, iobase); // Exit configuration
-
- return 0;
-}
-
-/* 82801CAM generic registers */
-#define VID 0x00
-#define DID 0x02
-#define PIRQ_A_D_ROUT 0x60
-#define SIRQ_CNTL 0x64
-#define PIRQ_E_H_ROUT 0x68
-#define PCI_DMA_C 0x90
-/* LPC-specific registers */
-#define COM_DEC 0xe0
-#define GEN1_DEC 0xe4
-#define LPC_EN 0xe6
-#define GEN2_DEC 0xec
-/*
- * Sets up the I/O range using the 82801CAM ISA bridge, 82801DBM LPC bridge
- * or Intel 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge.
- * They all work the same way!
- */
-static int __init preconfigure_through_82801(struct pci_dev *dev,
- struct
- smsc_ircc_subsystem_configuration
- *conf)
-{
- unsigned short tmpword;
- unsigned char tmpbyte;
-
- IRDA_MESSAGE("Setting up Intel 82801 controller and SMSC device\n");
- /*
- * Select the range for the COMA COM port (SIR)
- * Register COM_DEC:
- * Bit 7: reserved
- * Bit 6-4, COMB decode range
- * Bit 3: reserved
- * Bit 2-0, COMA decode range
- *
- * Decode ranges:
- * 000 = 0x3f8-0x3ff (COM1)
- * 001 = 0x2f8-0x2ff (COM2)
- * 010 = 0x220-0x227
- * 011 = 0x228-0x22f
- * 100 = 0x238-0x23f
- * 101 = 0x2e8-0x2ef (COM4)
- * 110 = 0x338-0x33f
- * 111 = 0x3e8-0x3ef (COM3)
- */
- pci_read_config_byte(dev, COM_DEC, &tmpbyte);
- tmpbyte &= 0xf8; /* mask COMA bits */
- switch(conf->sir_io) {
- case 0x3f8:
- tmpbyte |= 0x00;
- break;
- case 0x2f8:
- tmpbyte |= 0x01;
- break;
- case 0x220:
- tmpbyte |= 0x02;
- break;
- case 0x228:
- tmpbyte |= 0x03;
- break;
- case 0x238:
- tmpbyte |= 0x04;
- break;
- case 0x2e8:
- tmpbyte |= 0x05;
- break;
- case 0x338:
- tmpbyte |= 0x06;
- break;
- case 0x3e8:
- tmpbyte |= 0x07;
- break;
- default:
- tmpbyte |= 0x01; /* COM2 default */
- }
- IRDA_DEBUG(1, "COM_DEC (write): 0x%02x\n", tmpbyte);
- pci_write_config_byte(dev, COM_DEC, tmpbyte);
-
- /* Enable Low Pin Count interface */
- pci_read_config_word(dev, LPC_EN, &tmpword);
- /* These seem to be set up at all times,
- * just make sure it is properly set.
- */
- switch(conf->cfg_base) {
- case 0x04e:
- tmpword |= 0x2000;
- break;
- case 0x02e:
- tmpword |= 0x1000;
- break;
- case 0x062:
- tmpword |= 0x0800;
- break;
- case 0x060:
- tmpword |= 0x0400;
- break;
- default:
- IRDA_WARNING("Uncommon I/O base address: 0x%04x\n",
- conf->cfg_base);
- break;
- }
- tmpword &= 0xfffd; /* disable LPC COMB */
- tmpword |= 0x0001; /* set bit 0 : enable LPC COMA addr range (GEN2) */
- IRDA_DEBUG(1, "LPC_EN (write): 0x%04x\n", tmpword);
- pci_write_config_word(dev, LPC_EN, tmpword);
-
- /*
- * Configure LPC DMA channel
- * PCI_DMA_C bits:
- * Bit 15-14: DMA channel 7 select
- * Bit 13-12: DMA channel 6 select
- * Bit 11-10: DMA channel 5 select
- * Bit 9-8: Reserved
- * Bit 7-6: DMA channel 3 select
- * Bit 5-4: DMA channel 2 select
- * Bit 3-2: DMA channel 1 select
- * Bit 1-0: DMA channel 0 select
- * 00 = Reserved value
- * 01 = PC/PCI DMA
- * 10 = Reserved value
- * 11 = LPC I/F DMA
- */
- pci_read_config_word(dev, PCI_DMA_C, &tmpword);
- switch(conf->fir_dma) {
- case 0x07:
- tmpword |= 0xc000;
- break;
- case 0x06:
- tmpword |= 0x3000;
- break;
- case 0x05:
- tmpword |= 0x0c00;
- break;
- case 0x03:
- tmpword |= 0x00c0;
- break;
- case 0x02:
- tmpword |= 0x0030;
- break;
- case 0x01:
- tmpword |= 0x000c;
- break;
- case 0x00:
- tmpword |= 0x0003;
- break;
- default:
- break; /* do not change settings */
- }
- IRDA_DEBUG(1, "PCI_DMA_C (write): 0x%04x\n", tmpword);
- pci_write_config_word(dev, PCI_DMA_C, tmpword);
-
- /*
- * GEN2_DEC bits:
- * Bit 15-4: Generic I/O range
- * Bit 3-1: reserved (read as 0)
- * Bit 0: enable GEN2 range on LPC I/F
- */
- tmpword = conf->fir_io & 0xfff8;
- tmpword |= 0x0001;
- IRDA_DEBUG(1, "GEN2_DEC (write): 0x%04x\n", tmpword);
- pci_write_config_word(dev, GEN2_DEC, tmpword);
-
- /* Pre-configure chip */
- return preconfigure_smsc_chip(conf);
-}
-
-/*
- * Pre-configure a certain port on the ALi 1533 bridge.
- * This is based on reverse-engineering since ALi does not
- * provide any data sheet for the 1533 chip.
- */
-static void __init preconfigure_ali_port(struct pci_dev *dev,
- unsigned short port)
-{
- unsigned char reg;
- /* These bits obviously control the different ports */
- unsigned char mask;
- unsigned char tmpbyte;
-
- switch(port) {
- case 0x0130:
- case 0x0178:
- reg = 0xb0;
- mask = 0x80;
- break;
- case 0x03f8:
- reg = 0xb4;
- mask = 0x80;
- break;
- case 0x02f8:
- reg = 0xb4;
- mask = 0x30;
- break;
- case 0x02e8:
- reg = 0xb4;
- mask = 0x08;
- break;
- default:
- IRDA_ERROR("Failed to configure unsupported port on ALi 1533 bridge: 0x%04x\n", port);
- return;
- }
-
- pci_read_config_byte(dev, reg, &tmpbyte);
- /* Turn on the right bits */
- tmpbyte |= mask;
- pci_write_config_byte(dev, reg, tmpbyte);
- IRDA_MESSAGE("Activated ALi 1533 ISA bridge port 0x%04x.\n", port);
- return;
-}
-
-static int __init preconfigure_through_ali(struct pci_dev *dev,
- struct
- smsc_ircc_subsystem_configuration
- *conf)
-{
- /* Configure the two ports on the ALi 1533 */
- preconfigure_ali_port(dev, conf->sir_io);
- preconfigure_ali_port(dev, conf->fir_io);
-
- /* Pre-configure chip */
- return preconfigure_smsc_chip(conf);
-}
-
-static int __init smsc_ircc_preconfigure_subsystems(unsigned short ircc_cfg,
- unsigned short ircc_fir,
- unsigned short ircc_sir,
- unsigned char ircc_dma,
- unsigned char ircc_irq)
-{
- struct pci_dev *dev = NULL;
- unsigned short ss_vendor = 0x0000;
- unsigned short ss_device = 0x0000;
- int ret = 0;
-
- dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev);
-
- while (dev != NULL) {
- struct smsc_ircc_subsystem_configuration *conf;
-
- /*
- * Cache the subsystem vendor/device:
- * some manufacturers fail to set this for all components,
- * so we save it in case there is just 0x0000 0x0000 on the
- * device we want to check.
- */
- if (dev->subsystem_vendor != 0x0000U) {
- ss_vendor = dev->subsystem_vendor;
- ss_device = dev->subsystem_device;
- }
- conf = subsystem_configurations;
- for( ; conf->subvendor; conf++) {
- if(conf->vendor == dev->vendor &&
- conf->device == dev->device &&
- conf->subvendor == ss_vendor &&
- /* Sometimes these are cached values */
- (conf->subdevice == ss_device ||
- conf->subdevice == 0xffff)) {
- struct smsc_ircc_subsystem_configuration
- tmpconf;
-
- memcpy(&tmpconf, conf,
- sizeof(struct smsc_ircc_subsystem_configuration));
-
- /*
- * Override the default values with anything
- * passed in as parameter
- */
- if (ircc_cfg != 0)
- tmpconf.cfg_base = ircc_cfg;
- if (ircc_fir != 0)
- tmpconf.fir_io = ircc_fir;
- if (ircc_sir != 0)
- tmpconf.sir_io = ircc_sir;
- if (ircc_dma != 0xff)
- tmpconf.fir_dma = ircc_dma;
- if (ircc_irq != 0xff)
- tmpconf.fir_irq = ircc_irq;
-
- IRDA_MESSAGE("Detected unconfigured %s SMSC IrDA chip, pre-configuring device.\n", conf->name);
- if (conf->preconfigure)
- ret = conf->preconfigure(dev, &tmpconf);
- else
- ret = -ENODEV;
- }
- }
- dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev);
- }
-
- return ret;
-}
-#endif // CONFIG_PCI
-