-/* structure for MTIOCGETCONFIG/MTIOCSETCONFIG primarily intended
- * as an interim solution for QIC-02 until DDI is fully implemented.
- */
-struct mtconfiginfo {
- long mt_type; /* drive type */
- long ifc_type; /* interface card type */
- unsigned short irqnr; /* IRQ number to use */
- unsigned short dmanr; /* DMA channel to use */
- unsigned short port; /* IO port base address */
-
- unsigned long debug; /* debugging flags */
-
- unsigned have_dens:1;
- unsigned have_bsf:1;
- unsigned have_fsr:1;
- unsigned have_bsr:1;
- unsigned have_eod:1;
- unsigned have_seek:1;
- unsigned have_tell:1;
- unsigned have_ras1:1;
- unsigned have_ras2:1;
- unsigned have_ras3:1;
- unsigned have_qfa:1;
-
- unsigned pad1:5;
- char reserved[10];
-};
-
-/* structure for MTIOCVOLINFO, query information about the volume
- * currently positioned at (zftape)
- */
-struct mtvolinfo {
- unsigned int mt_volno; /* vol-number */
- unsigned int mt_blksz; /* blocksize used when recording */
- unsigned int mt_rawsize; /* raw tape space consumed, in kb */
- unsigned int mt_size; /* volume size after decompression, in kb */
- unsigned int mt_cmpr:1; /* this volume has been compressed */
-};
-
-/* raw access to a floppy drive, read and write an arbitrary segment.
- * For ftape/zftape to support formatting etc.
- */
-#define MT_FT_RD_SINGLE 0
-#define MT_FT_RD_AHEAD 1
-#define MT_FT_WR_ASYNC 0 /* start tape only when all buffers are full */
-#define MT_FT_WR_MULTI 1 /* start tape, continue until buffers are empty */
-#define MT_FT_WR_SINGLE 2 /* write a single segment and stop afterwards */
-#define MT_FT_WR_DELETE 3 /* write deleted data marks, one segment at time */
-
-struct mtftseg
-{
- unsigned mt_segno; /* the segment to read or write */
- unsigned mt_mode; /* modes for read/write (sync/async etc.) */
- int mt_result; /* result of r/w request, not of the ioctl */
- void __user *mt_data; /* User space buffer: must be 29kb */
-};
-
-/* get tape capacity (ftape/zftape)
- */
-struct mttapesize {
- unsigned long mt_capacity; /* entire, uncompressed capacity
- * of a cartridge
- */
- unsigned long mt_used; /* what has been used so far, raw
- * uncompressed amount
- */
-};
-
-/* possible values of the ftfmt_op field
- */
-#define FTFMT_SET_PARMS 1 /* set software parms */
-#define FTFMT_GET_PARMS 2 /* get software parms */
-#define FTFMT_FORMAT_TRACK 3 /* start formatting a tape track */
-#define FTFMT_STATUS 4 /* monitor formatting a tape track */
-#define FTFMT_VERIFY 5 /* verify the given segment */
-
-struct ftfmtparms {
- unsigned char ft_qicstd; /* QIC-40/QIC-80/QIC-3010/QIC-3020 */
- unsigned char ft_fmtcode; /* Refer to the QIC specs */
- unsigned char ft_fhm; /* floppy head max */
- unsigned char ft_ftm; /* floppy track max */
- unsigned short ft_spt; /* segments per track */
- unsigned short ft_tpc; /* tracks per cartridge */
-};
-
-struct ftfmttrack {
- unsigned int ft_track; /* track to format */
- unsigned char ft_gap3; /* size of gap3, for FORMAT_TRK */
-};
-
-struct ftfmtstatus {
- unsigned int ft_segment; /* segment currently being formatted */
-};
-
-struct ftfmtverify {
- unsigned int ft_segment; /* segment to verify */
- unsigned long ft_bsm; /* bsm as result of VERIFY cmd */
-};
-
-struct mtftformat {
- unsigned int fmt_op; /* operation to perform */
- union fmt_arg {
- struct ftfmtparms fmt_parms; /* format parameters */
- struct ftfmttrack fmt_track; /* ctrl while formatting */
- struct ftfmtstatus fmt_status;
- struct ftfmtverify fmt_verify; /* for verifying */
- } fmt_arg;
-};
-
-struct mtftcmd {
- unsigned int ft_wait_before; /* timeout to wait for drive to get ready
- * before command is sent. Milliseconds
- */
- qic117_cmd_t ft_cmd; /* command to send */
- unsigned char ft_parm_cnt; /* zero: no parm is sent. */
- unsigned char ft_parms[3]; /* parameter(s) to send to
- * the drive. The parms are nibbles
- * driver sends cmd + 2 step pulses */
- unsigned int ft_result_bits; /* if non zero, number of bits
- * returned by the tape drive
- */
- unsigned int ft_result; /* the result returned by the tape drive*/
- unsigned int ft_wait_after; /* timeout to wait for drive to get ready
- * after command is sent. 0: don't wait */
- int ft_status; /* status returned by ready wait
- * undefined if timeout was 0.
- */
- int ft_error; /* error code if error status was set by
- * command
- */
-};
-