* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-#include <linux/config.h>
#include <linux/types.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/mtd/physmap.h>
#include <asm/hardware.h>
#include <asm/setup.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/hardware.h>
-#include <asm/mach/serial_at91rm9200.h>
#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91rm9200_mc.h>
#include "generic.h"
-static void __init dk_init_irq(void)
-{
- /* Initialize AIC controller */
- at91rm9200_init_irq(NULL);
-
- /* Set up the GPIO interrupts */
- at91_gpio_irq_setup(BGA_GPIO_BANKS);
-}
/*
* Serial port configuration.
* 0 .. 3 = USART0 .. USART3
* 4 = DBGU
*/
-#define DK_UART_MAP { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */
-#define DK_SERIAL_CONSOLE 0 /* ttyS0 */
+static struct at91_uart_config __initdata dk_uart_config = {
+ .console_tty = 0, /* ttyS0 */
+ .nr_tty = 2,
+ .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */
+};
static void __init dk_map_io(void)
{
- int serial[AT91_NR_UART] = DK_UART_MAP;
- int i;
-
- at91rm9200_map_io();
+ /* Initialize processor: 18.432 MHz crystal */
+ at91rm9200_initialize(18432000, AT91RM9200_BGA);
- /* Initialize clocks: 18.432 MHz crystal */
- at91_clock_init(18432000);
+ /* Setup the LEDs */
+ at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
-#ifdef CONFIG_SERIAL_AT91
- at91_console_port = DK_SERIAL_CONSOLE;
- memcpy(at91_serial_map, serial, sizeof(serial));
+ /* Setup the serial ports and console */
+ at91_init_serial(&dk_uart_config);
+}
- /* Register UARTs */
- for (i = 0; i < AT91_NR_UART; i++) {
- if (at91_serial_map[i] >= 0)
- at91_register_uart(i, at91_serial_map[i]);
- }
-#endif
+static void __init dk_init_irq(void)
+{
+ at91rm9200_init_interrupts(NULL);
}
static struct at91_eth_data __initdata dk_eth_data = {
};
static struct at91_mmc_data __initdata dk_mmc_data = {
- .is_b = 0,
+ .slot_b = 0,
.wire4 = 1,
};
+static struct spi_board_info dk_spi_devices[] = {
+ { /* DataFlash chip */
+ .modalias = "mtd_dataflash",
+ .chip_select = 0,
+ .max_speed_hz = 15 * 1000 * 1000,
+ },
+ { /* UR6HCPS2-SP40 PS2-to-SPI adapter */
+ .modalias = "ur6hcps2",
+ .chip_select = 1,
+ .max_speed_hz = 250 * 1000,
+ },
+ { /* TLV1504 ADC, 4 channels, 10 bits; one is a temp sensor */
+ .modalias = "tlv1504",
+ .chip_select = 2,
+ .max_speed_hz = 20 * 1000 * 1000,
+ },
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+ { /* DataFlash card */
+ .modalias = "mtd_dataflash",
+ .chip_select = 3,
+ .max_speed_hz = 15 * 1000 * 1000,
+ }
+#endif
+};
+
+static struct mtd_partition __initdata dk_nand_partition[] = {
+ {
+ .name = "NAND Partition 1",
+ .offset = 0,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct mtd_partition *nand_partitions(int size, int *num_partitions)
+{
+ *num_partitions = ARRAY_SIZE(dk_nand_partition);
+ return dk_nand_partition;
+}
+
+static struct at91_nand_data __initdata dk_nand_data = {
+ .ale = 22,
+ .cle = 21,
+ .det_pin = AT91_PIN_PB1,
+ .rdy_pin = AT91_PIN_PC2,
+ // .enable_pin = ... not there
+ .partition_info = nand_partitions,
+};
+
+#define DK_FLASH_BASE AT91_CHIPSELECT_0
+#define DK_FLASH_SIZE 0x200000
+
+static struct physmap_flash_data dk_flash_data = {
+ .width = 2,
+};
+
+static struct resource dk_flash_resource = {
+ .start = DK_FLASH_BASE,
+ .end = DK_FLASH_BASE + DK_FLASH_SIZE - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device dk_flash = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &dk_flash_data,
+ },
+ .resource = &dk_flash_resource,
+ .num_resources = 1,
+};
+
+
static void __init dk_board_init(void)
{
+ /* Serial */
+ at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&dk_eth_data);
/* USB Host */
at91_add_device_usbh(&dk_usbh_data);
/* USB Device */
at91_add_device_udc(&dk_udc_data);
+ at91_set_multi_drive(dk_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
/* Compact Flash */
at91_add_device_cf(&dk_cf_data);
+ /* I2C */
+ at91_add_device_i2c();
+ /* SPI */
+ at91_add_device_spi(dk_spi_devices, ARRAY_SIZE(dk_spi_devices));
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+ /* DataFlash card */
+ at91_set_gpio_output(AT91_PIN_PB7, 0);
+#else
/* MMC */
- at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). default: MMC */
+ at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
at91_add_device_mmc(&dk_mmc_data);
+#endif
+ /* NAND */
+ at91_add_device_nand(&dk_nand_data);
+ /* NOR Flash */
+ platform_device_register(&dk_flash);
/* VGA */
// dk_add_device_video();
}