--- /dev/null
+/*
+ * arch/arm/mach-omap/omap2/serial.c
+ *
+ * OMAP2 serial support.
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Author: Paul Mundt <paul.mundt@nokia.com>
+ *
+ * Based off of arch/arm/mach-omap/omap1/serial.c
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_reg.h>
+#include <linux/clk.h>
+
+#include <asm/io.h>
+
+#include <asm/arch/common.h>
+#include <asm/arch/board.h>
+
+static struct clk * uart1_ick = NULL;
+static struct clk * uart1_fck = NULL;
+static struct clk * uart2_ick = NULL;
+static struct clk * uart2_fck = NULL;
+static struct clk * uart3_ick = NULL;
+static struct clk * uart3_fck = NULL;
+
+static struct plat_serial8250_port serial_platform_data[] = {
+ {
+ .membase = (char *)IO_ADDRESS(OMAP_UART1_BASE),
+ .mapbase = (unsigned long)OMAP_UART1_BASE,
+ .irq = 72,
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = OMAP16XX_BASE_BAUD * 16,
+ }, {
+ .membase = (char *)IO_ADDRESS(OMAP_UART2_BASE),
+ .mapbase = (unsigned long)OMAP_UART2_BASE,
+ .irq = 73,
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = OMAP16XX_BASE_BAUD * 16,
+ }, {
+ .membase = (char *)IO_ADDRESS(OMAP_UART3_BASE),
+ .mapbase = (unsigned long)OMAP_UART3_BASE,
+ .irq = 74,
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = OMAP16XX_BASE_BAUD * 16,
+ }, {
+ .flags = 0
+ }
+};
+
+static inline unsigned int serial_read_reg(struct plat_serial8250_port *up,
+ int offset)
+{
+ offset <<= up->regshift;
+ return (unsigned int)__raw_readb(up->membase + offset);
+}
+
+static inline void serial_write_reg(struct plat_serial8250_port *p, int offset,
+ int value)
+{
+ offset <<= p->regshift;
+ __raw_writeb(value, (unsigned long)(p->membase + offset));
+}
+
+/*
+ * Internal UARTs need to be initialized for the 8250 autoconfig to work
+ * properly. Note that the TX watermark initialization may not be needed
+ * once the 8250.c watermark handling code is merged.
+ */
+static inline void __init omap_serial_reset(struct plat_serial8250_port *p)
+{
+ serial_write_reg(p, UART_OMAP_MDR1, 0x07);
+ serial_write_reg(p, UART_OMAP_SCR, 0x08);
+ serial_write_reg(p, UART_OMAP_MDR1, 0x00);
+ serial_write_reg(p, UART_OMAP_SYSC, 0x01);
+}
+
+void __init omap_serial_init()
+{
+ int i;
+ const struct omap_uart_config *info;
+
+ /*
+ * Make sure the serial ports are muxed on at this point.
+ * You have to mux them off in device drivers later on
+ * if not needed.
+ */
+
+ info = omap_get_config(OMAP_TAG_UART,
+ struct omap_uart_config);
+
+ if (info == NULL)
+ return;
+
+ for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
+ struct plat_serial8250_port *p = serial_platform_data + i;
+
+ if (!(info->enabled_uarts & (1 << i))) {
+ p->membase = 0;
+ p->mapbase = 0;
+ continue;
+ }
+
+ switch (i) {
+ case 0:
+ uart1_ick = clk_get(NULL, "uart1_ick");
+ if (IS_ERR(uart1_ick))
+ printk("Could not get uart1_ick\n");
+ else {
+ clk_enable(uart1_ick);
+ }
+
+ uart1_fck = clk_get(NULL, "uart1_fck");
+ if (IS_ERR(uart1_fck))
+ printk("Could not get uart1_fck\n");
+ else {
+ clk_enable(uart1_fck);
+ }
+ break;
+ case 1:
+ uart2_ick = clk_get(NULL, "uart2_ick");
+ if (IS_ERR(uart2_ick))
+ printk("Could not get uart2_ick\n");
+ else {
+ clk_enable(uart2_ick);
+ }
+
+ uart2_fck = clk_get(NULL, "uart2_fck");
+ if (IS_ERR(uart2_fck))
+ printk("Could not get uart2_fck\n");
+ else {
+ clk_enable(uart2_fck);
+ }
+ break;
+ case 2:
+ uart3_ick = clk_get(NULL, "uart3_ick");
+ if (IS_ERR(uart3_ick))
+ printk("Could not get uart3_ick\n");
+ else {
+ clk_enable(uart3_ick);
+ }
+
+ uart3_fck = clk_get(NULL, "uart3_fck");
+ if (IS_ERR(uart3_fck))
+ printk("Could not get uart3_fck\n");
+ else {
+ clk_enable(uart3_fck);
+ }
+ break;
+ }
+
+ omap_serial_reset(p);
+ }
+}
+
+static struct platform_device serial_device = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = serial_platform_data,
+ },
+};
+
+static int __init omap_init(void)
+{
+ return platform_device_register(&serial_device);
+}
+arch_initcall(omap_init);
git://git.onelab.eu / linux-2.6.git / blobdiff