#include <linux/config.h>
#include <linux/init.h>
#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/clcd.h>
+#include <asm/system.h>
#include <asm/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/leds.h>
-#include <asm/mach-types.h>
-#include <asm/hardware/amba.h>
+#include <asm/hardware/arm_timer.h>
+#include <asm/hardware/icst307.h>
+#include <asm/hardware/vic.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/irq.h>
+#include <asm/mach/time.h>
#include <asm/mach/map.h>
-#ifdef CONFIG_MMC
#include <asm/mach/mmc.h>
-#endif
+
+#include "core.h"
+#include "clock.h"
/*
* All IO addresses are mapped onto VA 0xFFFx.xxxx, where x.xxxx
*
* Setup a VA for the Versatile Vectored Interrupt Controller.
*/
-#define VA_VIC_BASE IO_ADDRESS(VERSATILE_VIC_BASE)
-#define VA_SIC_BASE IO_ADDRESS(VERSATILE_SIC_BASE)
-
-static void vic_mask_irq(unsigned int irq)
-{
- irq -= IRQ_VIC_START;
- writel(1 << irq, VA_VIC_BASE + VIC_IRQ_ENABLE_CLEAR);
-}
-
-static void vic_unmask_irq(unsigned int irq)
-{
- irq -= IRQ_VIC_START;
- writel(1 << irq, VA_VIC_BASE + VIC_IRQ_ENABLE);
-}
-
-static struct irqchip vic_chip = {
- .ack = vic_mask_irq,
- .mask = vic_mask_irq,
- .unmask = vic_unmask_irq,
-};
+#define __io_address(n) __io(IO_ADDRESS(n))
+#define VA_VIC_BASE __io_address(VERSATILE_VIC_BASE)
+#define VA_SIC_BASE __io_address(VERSATILE_SIC_BASE)
static void sic_mask_irq(unsigned int irq)
{
irq += IRQ_SIC_START;
desc = irq_desc + irq;
- desc->handle(irq, desc, regs);
+ desc_handle_irq(irq, desc, regs);
} while (status);
}
#if 1
#define IRQ_MMCI0A IRQ_VICSOURCE22
-#define IRQ_MMCI1A IRQ_VICSOURCE23
#define IRQ_AACI IRQ_VICSOURCE24
#define IRQ_ETH IRQ_VICSOURCE25
#define PIC_MASK 0xFFD00000
#else
#define IRQ_MMCI0A IRQ_SIC_MMCI0A
-#define IRQ_MMCI1A IRQ_SIC_MMCI1A
#define IRQ_AACI IRQ_SIC_AACI
#define IRQ_ETH IRQ_SIC_ETH
#define PIC_MASK 0
#endif
-static void __init versatile_init_irq(void)
+void __init versatile_init_irq(void)
{
- unsigned int i, value;
-
- /* Disable all interrupts initially. */
+ unsigned int i;
- writel(0, VA_VIC_BASE + VIC_INT_SELECT);
- writel(0, VA_VIC_BASE + VIC_IRQ_ENABLE);
- writel(~0, VA_VIC_BASE + VIC_IRQ_ENABLE_CLEAR);
- writel(0, VA_VIC_BASE + VIC_IRQ_STATUS);
- writel(0, VA_VIC_BASE + VIC_ITCR);
- writel(~0, VA_VIC_BASE + VIC_IRQ_SOFT_CLEAR);
-
- /*
- * Make sure we clear all existing interrupts
- */
- writel(0, VA_VIC_BASE + VIC_VECT_ADDR);
- for (i = 0; i < 19; i++) {
- value = readl(VA_VIC_BASE + VIC_VECT_ADDR);
- writel(value, VA_VIC_BASE + VIC_VECT_ADDR);
- }
-
- for (i = 0; i < 16; i++) {
- value = readl(VA_VIC_BASE + VIC_VECT_CNTL0 + (i * 4));
- writel(value | VICVectCntl_Enable | i, VA_VIC_BASE + VIC_VECT_CNTL0 + (i * 4));
- }
-
- writel(32, VA_VIC_BASE + VIC_DEF_VECT_ADDR);
-
- for (i = IRQ_VIC_START; i <= IRQ_VIC_END; i++) {
- if (i != IRQ_VICSOURCE31) {
- set_irq_chip(i, &vic_chip);
- set_irq_handler(i, do_level_IRQ);
- set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
- }
- }
+ vic_init(VA_VIC_BASE, ~(1 << 31));
set_irq_handler(IRQ_VICSOURCE31, sic_handle_irq);
- vic_unmask_irq(IRQ_VICSOURCE31);
+ enable_irq(IRQ_VICSOURCE31);
/* Do second interrupt controller */
writel(~0, VA_SIC_BASE + SIC_IRQ_ENABLE_CLEAR);
}
static struct map_desc versatile_io_desc[] __initdata = {
- { IO_ADDRESS(VERSATILE_SYS_BASE), VERSATILE_SYS_BASE, SZ_4K, MT_DEVICE },
- { IO_ADDRESS(VERSATILE_SIC_BASE), VERSATILE_SIC_BASE, SZ_4K, MT_DEVICE },
- { IO_ADDRESS(VERSATILE_VIC_BASE), VERSATILE_VIC_BASE, SZ_4K, MT_DEVICE },
- { IO_ADDRESS(VERSATILE_SCTL_BASE), VERSATILE_SCTL_BASE, SZ_4K * 9, MT_DEVICE },
+ {
+ .virtual = IO_ADDRESS(VERSATILE_SYS_BASE),
+ .pfn = __phys_to_pfn(VERSATILE_SYS_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE
+ }, {
+ .virtual = IO_ADDRESS(VERSATILE_SIC_BASE),
+ .pfn = __phys_to_pfn(VERSATILE_SIC_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE
+ }, {
+ .virtual = IO_ADDRESS(VERSATILE_VIC_BASE),
+ .pfn = __phys_to_pfn(VERSATILE_VIC_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE
+ }, {
+ .virtual = IO_ADDRESS(VERSATILE_SCTL_BASE),
+ .pfn = __phys_to_pfn(VERSATILE_SCTL_BASE),
+ .length = SZ_4K * 9,
+ .type = MT_DEVICE
+ },
+#ifdef CONFIG_MACH_VERSATILE_AB
+ {
+ .virtual = IO_ADDRESS(VERSATILE_GPIO0_BASE),
+ .pfn = __phys_to_pfn(VERSATILE_GPIO0_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE
+ }, {
+ .virtual = IO_ADDRESS(VERSATILE_IB2_BASE),
+ .pfn = __phys_to_pfn(VERSATILE_IB2_BASE),
+ .length = SZ_64M,
+ .type = MT_DEVICE
+ },
+#endif
#ifdef CONFIG_DEBUG_LL
- { IO_ADDRESS(VERSATILE_UART0_BASE), VERSATILE_UART0_BASE, SZ_4K, MT_DEVICE },
+ {
+ .virtual = IO_ADDRESS(VERSATILE_UART0_BASE),
+ .pfn = __phys_to_pfn(VERSATILE_UART0_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE
+ },
+#endif
+#ifdef CONFIG_PCI
+ {
+ .virtual = IO_ADDRESS(VERSATILE_PCI_CORE_BASE),
+ .pfn = __phys_to_pfn(VERSATILE_PCI_CORE_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE
+ }, {
+ .virtual = VERSATILE_PCI_VIRT_BASE,
+ .pfn = __phys_to_pfn(VERSATILE_PCI_BASE),
+ .length = VERSATILE_PCI_BASE_SIZE,
+ .type = MT_DEVICE
+ }, {
+ .virtual = VERSATILE_PCI_CFG_VIRT_BASE,
+ .pfn = __phys_to_pfn(VERSATILE_PCI_CFG_BASE),
+ .length = VERSATILE_PCI_CFG_BASE_SIZE,
+ .type = MT_DEVICE
+ },
+#if 0
+ {
+ .virtual = VERSATILE_PCI_VIRT_MEM_BASE0,
+ .pfn = __phys_to_pfn(VERSATILE_PCI_MEM_BASE0),
+ .length = SZ_16M,
+ .type = MT_DEVICE
+ }, {
+ .virtual = VERSATILE_PCI_VIRT_MEM_BASE1,
+ .pfn = __phys_to_pfn(VERSATILE_PCI_MEM_BASE1),
+ .length = SZ_16M,
+ .type = MT_DEVICE
+ }, {
+ .virtual = VERSATILE_PCI_VIRT_MEM_BASE2,
+ .pfn = __phys_to_pfn(VERSATILE_PCI_MEM_BASE2),
+ .length = SZ_16M,
+ .type = MT_DEVICE
+ },
#endif
-#ifdef FIXME
- { PCI_MEMORY_VADDR, PHYS_PCI_MEM_BASE, SZ_16M, MT_DEVICE },
- { PCI_CONFIG_VADDR, PHYS_PCI_CONFIG_BASE, SZ_16M, MT_DEVICE },
- { PCI_V3_VADDR, PHYS_PCI_V3_BASE, SZ_512K, MT_DEVICE },
- { PCI_IO_VADDR, PHYS_PCI_IO_BASE, SZ_64K, MT_DEVICE },
#endif
};
-static void __init versatile_map_io(void)
+void __init versatile_map_io(void)
{
iotable_init(versatile_io_desc, ARRAY_SIZE(versatile_io_desc));
}
-#define VERSATILE_REFCOUNTER (IO_ADDRESS(VERSATILE_SYS_BASE) + VERSATILE_SYS_24MHz_OFFSET)
+#define VERSATILE_REFCOUNTER (__io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_24MHz_OFFSET)
/*
- * This is the VersatilePB sched_clock implementation. This has
+ * This is the Versatile sched_clock implementation. This has
* a resolution of 41.7ns, and a maximum value of about 179s.
*/
unsigned long long sched_clock(void)
}
-#define VERSATILE_FLASHCTRL (IO_ADDRESS(VERSATILE_SYS_BASE) + VERSATILE_SYS_FLASH_OFFSET)
+#define VERSATILE_FLASHCTRL (__io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_FLASH_OFFSET)
static int versatile_flash_init(void)
{
.resource = smc91x_resources,
};
-#define VERSATILE_SYSMCI (IO_ADDRESS(VERSATILE_SYS_BASE) + VERSATILE_SYS_MCI_OFFSET)
+#define VERSATILE_SYSMCI (__io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_MCI_OFFSET)
-#ifdef CONFIG_MMC
-static unsigned int mmc_status(struct device *dev)
+unsigned int mmc_status(struct device *dev)
{
struct amba_device *adev = container_of(dev, struct amba_device, dev);
u32 mask;
}
static struct mmc_platform_data mmc0_plat_data = {
- .mclk = 33000000,
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = mmc_status,
};
-static struct mmc_platform_data mmc1_plat_data = {
- .mclk = 33000000,
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .status = mmc_status,
+/*
+ * Clock handling
+ */
+static const struct icst307_params versatile_oscvco_params = {
+ .ref = 24000,
+ .vco_max = 200000,
+ .vd_min = 4 + 8,
+ .vd_max = 511 + 8,
+ .rd_min = 1 + 2,
+ .rd_max = 127 + 2,
};
+
+static void versatile_oscvco_set(struct clk *clk, struct icst307_vco vco)
+{
+ void __iomem *sys_lock = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_LOCK_OFFSET;
+#if defined(CONFIG_ARCH_VERSATILE_PB)
+ void __iomem *sys_osc = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_OSC4_OFFSET;
+#elif defined(CONFIG_MACH_VERSATILE_AB)
+ void __iomem *sys_osc = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_OSC1_OFFSET;
+#endif
+ u32 val;
+
+ val = readl(sys_osc) & ~0x7ffff;
+ val |= vco.v | (vco.r << 9) | (vco.s << 16);
+
+ writel(0xa05f, sys_lock);
+ writel(val, sys_osc);
+ writel(0, sys_lock);
+}
+
+static struct clk versatile_clcd_clk = {
+ .name = "CLCDCLK",
+ .params = &versatile_oscvco_params,
+ .setvco = versatile_oscvco_set,
+};
+
+/*
+ * CLCD support.
+ */
+#define SYS_CLCD_MODE_MASK (3 << 0)
+#define SYS_CLCD_MODE_888 (0 << 0)
+#define SYS_CLCD_MODE_5551 (1 << 0)
+#define SYS_CLCD_MODE_565_RLSB (2 << 0)
+#define SYS_CLCD_MODE_565_BLSB (3 << 0)
+#define SYS_CLCD_NLCDIOON (1 << 2)
+#define SYS_CLCD_VDDPOSSWITCH (1 << 3)
+#define SYS_CLCD_PWR3V5SWITCH (1 << 4)
+#define SYS_CLCD_ID_MASK (0x1f << 8)
+#define SYS_CLCD_ID_SANYO_3_8 (0x00 << 8)
+#define SYS_CLCD_ID_UNKNOWN_8_4 (0x01 << 8)
+#define SYS_CLCD_ID_EPSON_2_2 (0x02 << 8)
+#define SYS_CLCD_ID_SANYO_2_5 (0x07 << 8)
+#define SYS_CLCD_ID_VGA (0x1f << 8)
+
+static struct clcd_panel vga = {
+ .mode = {
+ .name = "VGA",
+ .refresh = 60,
+ .xres = 640,
+ .yres = 480,
+ .pixclock = 39721,
+ .left_margin = 40,
+ .right_margin = 24,
+ .upper_margin = 32,
+ .lower_margin = 11,
+ .hsync_len = 96,
+ .vsync_len = 2,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_BCD | TIM2_IPC,
+ .cntl = CNTL_LCDTFT | CNTL_LCDVCOMP(1),
+ .bpp = 16,
+};
+
+static struct clcd_panel sanyo_3_8_in = {
+ .mode = {
+ .name = "Sanyo QVGA",
+ .refresh = 116,
+ .xres = 320,
+ .yres = 240,
+ .pixclock = 100000,
+ .left_margin = 6,
+ .right_margin = 6,
+ .upper_margin = 5,
+ .lower_margin = 5,
+ .hsync_len = 6,
+ .vsync_len = 6,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_BCD,
+ .cntl = CNTL_LCDTFT | CNTL_LCDVCOMP(1),
+ .bpp = 16,
+};
+
+static struct clcd_panel sanyo_2_5_in = {
+ .mode = {
+ .name = "Sanyo QVGA Portrait",
+ .refresh = 116,
+ .xres = 240,
+ .yres = 320,
+ .pixclock = 100000,
+ .left_margin = 20,
+ .right_margin = 10,
+ .upper_margin = 2,
+ .lower_margin = 2,
+ .hsync_len = 10,
+ .vsync_len = 2,
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_IVS | TIM2_IHS | TIM2_IPC,
+ .cntl = CNTL_LCDTFT | CNTL_LCDVCOMP(1),
+ .bpp = 16,
+};
+
+static struct clcd_panel epson_2_2_in = {
+ .mode = {
+ .name = "Epson QCIF",
+ .refresh = 390,
+ .xres = 176,
+ .yres = 220,
+ .pixclock = 62500,
+ .left_margin = 3,
+ .right_margin = 2,
+ .upper_margin = 1,
+ .lower_margin = 0,
+ .hsync_len = 3,
+ .vsync_len = 2,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_BCD | TIM2_IPC,
+ .cntl = CNTL_LCDTFT | CNTL_LCDVCOMP(1),
+ .bpp = 16,
+};
+
+/*
+ * Detect which LCD panel is connected, and return the appropriate
+ * clcd_panel structure. Note: we do not have any information on
+ * the required timings for the 8.4in panel, so we presently assume
+ * VGA timings.
+ */
+static struct clcd_panel *versatile_clcd_panel(void)
+{
+ void __iomem *sys_clcd = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_CLCD_OFFSET;
+ struct clcd_panel *panel = &vga;
+ u32 val;
+
+ val = readl(sys_clcd) & SYS_CLCD_ID_MASK;
+ if (val == SYS_CLCD_ID_SANYO_3_8)
+ panel = &sanyo_3_8_in;
+ else if (val == SYS_CLCD_ID_SANYO_2_5)
+ panel = &sanyo_2_5_in;
+ else if (val == SYS_CLCD_ID_EPSON_2_2)
+ panel = &epson_2_2_in;
+ else if (val == SYS_CLCD_ID_VGA)
+ panel = &vga;
+ else {
+ printk(KERN_ERR "CLCD: unknown LCD panel ID 0x%08x, using VGA\n",
+ val);
+ panel = &vga;
+ }
+
+ return panel;
+}
+
+/*
+ * Disable all display connectors on the interface module.
+ */
+static void versatile_clcd_disable(struct clcd_fb *fb)
+{
+ void __iomem *sys_clcd = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_CLCD_OFFSET;
+ u32 val;
+
+ val = readl(sys_clcd);
+ val &= ~SYS_CLCD_NLCDIOON | SYS_CLCD_PWR3V5SWITCH;
+ writel(val, sys_clcd);
+
+#ifdef CONFIG_MACH_VERSATILE_AB
+ /*
+ * If the LCD is Sanyo 2x5 in on the IB2 board, turn the back-light off
+ */
+ if (fb->panel == &sanyo_2_5_in) {
+ void __iomem *versatile_ib2_ctrl = __io_address(VERSATILE_IB2_CTRL);
+ unsigned long ctrl;
+
+ ctrl = readl(versatile_ib2_ctrl);
+ ctrl &= ~0x01;
+ writel(ctrl, versatile_ib2_ctrl);
+ }
+#endif
+}
+
+/*
+ * Enable the relevant connector on the interface module.
+ */
+static void versatile_clcd_enable(struct clcd_fb *fb)
+{
+ void __iomem *sys_clcd = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_CLCD_OFFSET;
+ u32 val;
+
+ val = readl(sys_clcd);
+ val &= ~SYS_CLCD_MODE_MASK;
+
+ switch (fb->fb.var.green.length) {
+ case 5:
+ val |= SYS_CLCD_MODE_5551;
+ break;
+ case 6:
+ val |= SYS_CLCD_MODE_565_RLSB;
+ break;
+ case 8:
+ val |= SYS_CLCD_MODE_888;
+ break;
+ }
+
+ /*
+ * Set the MUX
+ */
+ writel(val, sys_clcd);
+
+ /*
+ * And now enable the PSUs
+ */
+ val |= SYS_CLCD_NLCDIOON | SYS_CLCD_PWR3V5SWITCH;
+ writel(val, sys_clcd);
+
+#ifdef CONFIG_MACH_VERSATILE_AB
+ /*
+ * If the LCD is Sanyo 2x5 in on the IB2 board, turn the back-light on
+ */
+ if (fb->panel == &sanyo_2_5_in) {
+ void __iomem *versatile_ib2_ctrl = __io_address(VERSATILE_IB2_CTRL);
+ unsigned long ctrl;
+
+ ctrl = readl(versatile_ib2_ctrl);
+ ctrl |= 0x01;
+ writel(ctrl, versatile_ib2_ctrl);
+ }
#endif
+}
+
+static unsigned long framesize = SZ_1M;
+
+static int versatile_clcd_setup(struct clcd_fb *fb)
+{
+ dma_addr_t dma;
+
+ fb->panel = versatile_clcd_panel();
+
+ fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev, framesize,
+ &dma, GFP_KERNEL);
+ if (!fb->fb.screen_base) {
+ printk(KERN_ERR "CLCD: unable to map framebuffer\n");
+ return -ENOMEM;
+ }
+
+ fb->fb.fix.smem_start = dma;
+ fb->fb.fix.smem_len = framesize;
-#define AMBA_DEVICE(name,busid,base,plat) \
-static struct amba_device name##_device = { \
- .dev = { \
- .coherent_dma_mask = ~0, \
- .bus_id = busid, \
- .platform_data = plat, \
- }, \
- .res = { \
- .start = VERSATILE_##base##_BASE, \
- .end = (VERSATILE_##base##_BASE) + SZ_4K - 1,\
- .flags = IORESOURCE_MEM, \
- }, \
- .irq = base##_IRQ, \
- /* .dma = base##_DMA,*/ \
+ return 0;
+}
+
+static int versatile_clcd_mmap(struct clcd_fb *fb, struct vm_area_struct *vma)
+{
+ return dma_mmap_writecombine(&fb->dev->dev, vma,
+ fb->fb.screen_base,
+ fb->fb.fix.smem_start,
+ fb->fb.fix.smem_len);
}
+static void versatile_clcd_remove(struct clcd_fb *fb)
+{
+ dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len,
+ fb->fb.screen_base, fb->fb.fix.smem_start);
+}
+
+static struct clcd_board clcd_plat_data = {
+ .name = "Versatile",
+ .check = clcdfb_check,
+ .decode = clcdfb_decode,
+ .disable = versatile_clcd_disable,
+ .enable = versatile_clcd_enable,
+ .setup = versatile_clcd_setup,
+ .mmap = versatile_clcd_mmap,
+ .remove = versatile_clcd_remove,
+};
+
#define AACI_IRQ { IRQ_AACI, NO_IRQ }
#define AACI_DMA { 0x80, 0x81 }
#define MMCI0_IRQ { IRQ_MMCI0A,IRQ_SIC_MMCI0B }
#define KMI0_DMA { 0, 0 }
#define KMI1_IRQ { IRQ_SIC_KMI1, NO_IRQ }
#define KMI1_DMA { 0, 0 }
-#define UART3_IRQ { IRQ_SIC_UART3, NO_IRQ }
-#define UART3_DMA { 0x86, 0x87 }
-#define SCI1_IRQ { IRQ_SIC_SCI3, NO_IRQ }
-#define SCI1_DMA { 0x88, 0x89 }
-#define MMCI1_IRQ { IRQ_MMCI1A, IRQ_SIC_MMCI1B }
-#define MMCI1_DMA { 0x85, 0 }
/*
* These devices are connected directly to the multi-layer AHB switch
#define GPIO0_DMA { 0, 0 }
#define GPIO1_IRQ { IRQ_GPIOINT1, NO_IRQ }
#define GPIO1_DMA { 0, 0 }
-#define GPIO2_IRQ { IRQ_GPIOINT2, NO_IRQ }
-#define GPIO2_DMA { 0, 0 }
-#define GPIO3_IRQ { IRQ_GPIOINT3, NO_IRQ }
-#define GPIO3_DMA { 0, 0 }
#define RTC_IRQ { IRQ_RTCINT, NO_IRQ }
#define RTC_DMA { 0, 0 }
/* FPGA Primecells */
AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-#ifdef CONFIG_MMC
AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &mmc0_plat_data);
-#endif
AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:09", UART3, NULL);
-AMBA_DEVICE(sci1, "fpga:0a", SCI1, NULL);
-#ifdef CONFIG_MMC
-AMBA_DEVICE(mmc1, "fpga:0b", MMCI1, &mmc1_plat_data);
-#endif
/* DevChip Primecells */
AMBA_DEVICE(smc, "dev:00", SMC, NULL);
AMBA_DEVICE(mpmc, "dev:10", MPMC, NULL);
-AMBA_DEVICE(clcd, "dev:20", CLCD, NULL);
+AMBA_DEVICE(clcd, "dev:20", CLCD, &clcd_plat_data);
AMBA_DEVICE(dmac, "dev:30", DMAC, NULL);
AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
AMBA_DEVICE(wdog, "dev:e1", WATCHDOG, NULL);
AMBA_DEVICE(gpio0, "dev:e4", GPIO0, NULL);
AMBA_DEVICE(gpio1, "dev:e5", GPIO1, NULL);
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, NULL);
-AMBA_DEVICE(gpio3, "dev:e7", GPIO3, NULL);
AMBA_DEVICE(rtc, "dev:e8", RTC, NULL);
AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
AMBA_DEVICE(uart0, "dev:f1", UART0, NULL);
&uart0_device,
&uart1_device,
&uart2_device,
- &uart3_device,
&smc_device,
&mpmc_device,
&clcd_device,
&wdog_device,
&gpio0_device,
&gpio1_device,
- &gpio2_device,
- &gpio3_device,
&rtc_device,
&sci0_device,
&ssp0_device,
&aaci_device,
-#ifdef CONFIG_MMC
&mmc0_device,
-#endif
&kmi0_device,
&kmi1_device,
- &sci1_device,
-#ifdef CONFIG_MMC
- &mmc1_device,
-#endif
};
-#define VA_LEDS_BASE (IO_ADDRESS(VERSATILE_SYS_BASE) + VERSATILE_SYS_LED_OFFSET)
+#ifdef CONFIG_LEDS
+#define VA_LEDS_BASE (__io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_LED_OFFSET)
static void versatile_leds_event(led_event_t ledevt)
{
writel(val, VA_LEDS_BASE);
local_irq_restore(flags);
}
+#endif /* CONFIG_LEDS */
-static void __init versatile_init(void)
+void __init versatile_init(void)
{
int i;
- platform_add_device(&versatile_flash_device);
- platform_add_device(&smc91x_device);
+ clk_register(&versatile_clcd_clk);
+
+ platform_device_register(&versatile_flash_device);
+ platform_device_register(&smc91x_device);
for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
struct amba_device *d = amba_devs[i];
amba_device_register(d, &iomem_resource);
}
+#ifdef CONFIG_LEDS
leds_event = versatile_leds_event;
+#endif
}
-MACHINE_START(VERSATILE_PB, "ARM-Versatile PB")
- MAINTAINER("ARM Ltd/Deep Blue Solutions Ltd")
- BOOT_MEM(0x00000000, 0x101f1000, 0xf11f1000)
- BOOT_PARAMS(0x00000100)
- MAPIO(versatile_map_io)
- INITIRQ(versatile_init_irq)
- INIT_MACHINE(versatile_init)
-MACHINE_END
+/*
+ * Where is the timer (VA)?
+ */
+#define TIMER0_VA_BASE __io_address(VERSATILE_TIMER0_1_BASE)
+#define TIMER1_VA_BASE (__io_address(VERSATILE_TIMER0_1_BASE) + 0x20)
+#define TIMER2_VA_BASE __io_address(VERSATILE_TIMER2_3_BASE)
+#define TIMER3_VA_BASE (__io_address(VERSATILE_TIMER2_3_BASE) + 0x20)
+#define VA_IC_BASE __io_address(VERSATILE_VIC_BASE)
+
+/*
+ * How long is the timer interval?
+ */
+#define TIMER_INTERVAL (TICKS_PER_uSEC * mSEC_10)
+#if TIMER_INTERVAL >= 0x100000
+#define TIMER_RELOAD (TIMER_INTERVAL >> 8)
+#define TIMER_DIVISOR (TIMER_CTRL_DIV256)
+#define TICKS2USECS(x) (256 * (x) / TICKS_PER_uSEC)
+#elif TIMER_INTERVAL >= 0x10000
+#define TIMER_RELOAD (TIMER_INTERVAL >> 4) /* Divide by 16 */
+#define TIMER_DIVISOR (TIMER_CTRL_DIV16)
+#define TICKS2USECS(x) (16 * (x) / TICKS_PER_uSEC)
+#else
+#define TIMER_RELOAD (TIMER_INTERVAL)
+#define TIMER_DIVISOR (TIMER_CTRL_DIV1)
+#define TICKS2USECS(x) ((x) / TICKS_PER_uSEC)
+#endif
+
+/*
+ * Returns number of ms since last clock interrupt. Note that interrupts
+ * will have been disabled by do_gettimeoffset()
+ */
+static unsigned long versatile_gettimeoffset(void)
+{
+ unsigned long ticks1, ticks2, status;
+
+ /*
+ * Get the current number of ticks. Note that there is a race
+ * condition between us reading the timer and checking for
+ * an interrupt. We get around this by ensuring that the
+ * counter has not reloaded between our two reads.
+ */
+ ticks2 = readl(TIMER0_VA_BASE + TIMER_VALUE) & 0xffff;
+ do {
+ ticks1 = ticks2;
+ status = __raw_readl(VA_IC_BASE + VIC_RAW_STATUS);
+ ticks2 = readl(TIMER0_VA_BASE + TIMER_VALUE) & 0xffff;
+ } while (ticks2 > ticks1);
+
+ /*
+ * Number of ticks since last interrupt.
+ */
+ ticks1 = TIMER_RELOAD - ticks2;
+
+ /*
+ * Interrupt pending? If so, we've reloaded once already.
+ *
+ * FIXME: Need to check this is effectively timer 0 that expires
+ */
+ if (status & IRQMASK_TIMERINT0_1)
+ ticks1 += TIMER_RELOAD;
+
+ /*
+ * Convert the ticks to usecs
+ */
+ return TICKS2USECS(ticks1);
+}
+
+/*
+ * IRQ handler for the timer
+ */
+static irqreturn_t versatile_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+ write_seqlock(&xtime_lock);
+
+ // ...clear the interrupt
+ writel(1, TIMER0_VA_BASE + TIMER_INTCLR);
+
+ timer_tick(regs);
+
+ write_sequnlock(&xtime_lock);
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction versatile_timer_irq = {
+ .name = "Versatile Timer Tick",
+ .flags = SA_INTERRUPT | SA_TIMER,
+ .handler = versatile_timer_interrupt,
+};
+
+/*
+ * Set up timer interrupt, and return the current time in seconds.
+ */
+static void __init versatile_timer_init(void)
+{
+ u32 val;
+
+ /*
+ * set clock frequency:
+ * VERSATILE_REFCLK is 32KHz
+ * VERSATILE_TIMCLK is 1MHz
+ */
+ val = readl(__io_address(VERSATILE_SCTL_BASE));
+ writel((VERSATILE_TIMCLK << VERSATILE_TIMER1_EnSel) |
+ (VERSATILE_TIMCLK << VERSATILE_TIMER2_EnSel) |
+ (VERSATILE_TIMCLK << VERSATILE_TIMER3_EnSel) |
+ (VERSATILE_TIMCLK << VERSATILE_TIMER4_EnSel) | val,
+ __io_address(VERSATILE_SCTL_BASE));
+
+ /*
+ * Initialise to a known state (all timers off)
+ */
+ writel(0, TIMER0_VA_BASE + TIMER_CTRL);
+ writel(0, TIMER1_VA_BASE + TIMER_CTRL);
+ writel(0, TIMER2_VA_BASE + TIMER_CTRL);
+ writel(0, TIMER3_VA_BASE + TIMER_CTRL);
+
+ writel(TIMER_RELOAD, TIMER0_VA_BASE + TIMER_LOAD);
+ writel(TIMER_RELOAD, TIMER0_VA_BASE + TIMER_VALUE);
+ writel(TIMER_DIVISOR | TIMER_CTRL_ENABLE | TIMER_CTRL_PERIODIC |
+ TIMER_CTRL_IE, TIMER0_VA_BASE + TIMER_CTRL);
+
+ /*
+ * Make irqs happen for the system timer
+ */
+ setup_irq(IRQ_TIMERINT0_1, &versatile_timer_irq);
+}
+
+struct sys_timer versatile_timer = {
+ .init = versatile_timer_init,
+ .offset = versatile_gettimeoffset,
+};