National Semiconductor SCx200 support. */
-#include <linux/config.h>
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/kernel.h>
#include <linux/init.h>
+#include <linux/mutex.h>
#include <linux/pci.h>
#include <linux/scx200.h>
-#include <linux/scx200.h>
+#include <linux/scx200_gpio.h>
+
+/* Verify that the configuration block really is there */
+#define scx200_cb_probe(base) (inw((base) + SCx200_CBA) == (base))
#define NAME "scx200"
unsigned scx200_gpio_base = 0;
long scx200_gpio_shadow[2];
-spinlock_t scx200_gpio_lock = SPIN_LOCK_UNLOCKED;
-static spinlock_t scx200_gpio_config_lock = SPIN_LOCK_UNLOCKED;
+unsigned scx200_cb_base = 0;
-u32 scx200_gpio_configure(int index, u32 mask, u32 bits)
-{
- u32 config, new_config;
- unsigned long flags;
+static struct pci_device_id scx200_tbl[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SCx200_BRIDGE) },
+ { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SC1100_BRIDGE) },
+ { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SCx200_XBUS) },
+ { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SC1100_XBUS) },
+ { },
+};
+MODULE_DEVICE_TABLE(pci,scx200_tbl);
- spin_lock_irqsave(&scx200_gpio_config_lock, flags);
+static int __devinit scx200_probe(struct pci_dev *, const struct pci_device_id *);
- outl(index, scx200_gpio_base + 0x20);
- config = inl(scx200_gpio_base + 0x24);
+static struct pci_driver scx200_pci_driver = {
+ .name = "scx200",
+ .id_table = scx200_tbl,
+ .probe = scx200_probe,
+};
- new_config = (config & mask) | bits;
- outl(new_config, scx200_gpio_base + 0x24);
+static DEFINE_MUTEX(scx200_gpio_config_lock);
- spin_unlock_irqrestore(&scx200_gpio_config_lock, flags);
+static void __devinit scx200_init_shadow(void)
+{
+ int bank;
- return config;
+ /* read the current values driven on the GPIO signals */
+ for (bank = 0; bank < 2; ++bank)
+ scx200_gpio_shadow[bank] = inl(scx200_gpio_base + 0x10 * bank);
}
-void scx200_gpio_dump(unsigned index)
+static int __devinit scx200_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
{
- u32 config = scx200_gpio_configure(index, ~0, 0);
- printk(KERN_DEBUG "GPIO%02u: 0x%08lx", index, (unsigned long)config);
-
- if (config & 1)
- printk(" OE"); /* output enabled */
- else
- printk(" TS"); /* tristate */
- if (config & 2)
- printk(" PP"); /* push pull */
- else
- printk(" OD"); /* open drain */
- if (config & 4)
- printk(" PUE"); /* pull up enabled */
- else
- printk(" PUD"); /* pull up disabled */
- if (config & 8)
- printk(" LOCKED"); /* locked */
- if (config & 16)
- printk(" LEVEL"); /* level input */
- else
- printk(" EDGE"); /* edge input */
- if (config & 32)
- printk(" HI"); /* trigger on rising edge */
- else
- printk(" LO"); /* trigger on falling edge */
- if (config & 64)
- printk(" DEBOUNCE"); /* debounce */
- printk("\n");
+ unsigned base;
+
+ if (pdev->device == PCI_DEVICE_ID_NS_SCx200_BRIDGE ||
+ pdev->device == PCI_DEVICE_ID_NS_SC1100_BRIDGE) {
+ base = pci_resource_start(pdev, 0);
+ printk(KERN_INFO NAME ": GPIO base 0x%x\n", base);
+
+ if (request_region(base, SCx200_GPIO_SIZE, "NatSemi SCx200 GPIO") == 0) {
+ printk(KERN_ERR NAME ": can't allocate I/O for GPIOs\n");
+ return -EBUSY;
+ }
+
+ scx200_gpio_base = base;
+ scx200_init_shadow();
+
+ } else {
+ /* find the base of the Configuration Block */
+ if (scx200_cb_probe(SCx200_CB_BASE_FIXED)) {
+ scx200_cb_base = SCx200_CB_BASE_FIXED;
+ } else {
+ pci_read_config_dword(pdev, SCx200_CBA_SCRATCH, &base);
+ if (scx200_cb_probe(base)) {
+ scx200_cb_base = base;
+ } else {
+ printk(KERN_WARNING NAME ": Configuration Block not found\n");
+ return -ENODEV;
+ }
+ }
+ printk(KERN_INFO NAME ": Configuration Block base 0x%x\n", scx200_cb_base);
+ }
+
+ return 0;
}
-int __init scx200_init(void)
+u32 scx200_gpio_configure(unsigned index, u32 mask, u32 bits)
{
- struct pci_dev *bridge;
- int bank;
- unsigned base;
+ u32 config, new_config;
- printk(KERN_INFO NAME ": NatSemi SCx200 Driver\n");
+ mutex_lock(&scx200_gpio_config_lock);
- if ((bridge = pci_find_device(PCI_VENDOR_ID_NS,
- PCI_DEVICE_ID_NS_SCx200_BRIDGE,
- NULL)) == NULL
- && (bridge = pci_find_device(PCI_VENDOR_ID_NS,
- PCI_DEVICE_ID_NS_SC1100_BRIDGE,
- NULL)) == NULL)
- return -ENODEV;
+ outl(index, scx200_gpio_base + 0x20);
+ config = inl(scx200_gpio_base + 0x24);
- base = pci_resource_start(bridge, 0);
- printk(KERN_INFO NAME ": GPIO base 0x%x\n", base);
+ new_config = (config & mask) | bits;
+ outl(new_config, scx200_gpio_base + 0x24);
- if (request_region(base, SCx200_GPIO_SIZE, "NatSemi SCx200 GPIO") == 0) {
- printk(KERN_ERR NAME ": can't allocate I/O for GPIOs\n");
- return -EBUSY;
- }
+ mutex_unlock(&scx200_gpio_config_lock);
- scx200_gpio_base = base;
+ return config;
+}
- /* read the current values driven on the GPIO signals */
- for (bank = 0; bank < 2; ++bank)
- scx200_gpio_shadow[bank] = inl(scx200_gpio_base + 0x10 * bank);
+static int __init scx200_init(void)
+{
+ printk(KERN_INFO NAME ": NatSemi SCx200 Driver\n");
- return 0;
+ return pci_register_driver(&scx200_pci_driver);
}
-void __exit scx200_cleanup(void)
+static void __exit scx200_cleanup(void)
{
+ pci_unregister_driver(&scx200_pci_driver);
release_region(scx200_gpio_base, SCx200_GPIO_SIZE);
}
EXPORT_SYMBOL(scx200_gpio_base);
EXPORT_SYMBOL(scx200_gpio_shadow);
-EXPORT_SYMBOL(scx200_gpio_lock);
EXPORT_SYMBOL(scx200_gpio_configure);
-EXPORT_SYMBOL(scx200_gpio_dump);
-
-/*
- Local variables:
- compile-command: "make -k -C ../../.. SUBDIRS=arch/i386/kernel modules"
- c-basic-offset: 8
- End:
-*/
+EXPORT_SYMBOL(scx200_cb_base);