bool
default y
-config GENERIC_HWEIGHT
- bool
- default y
-
config GENERIC_CALIBRATE_DELAY
bool
default y
select 83xx
select PPC_FPU
-config PPC_85xx
- bool "Freescale 85xx"
- select E500
- select FSL_SOC
- select 85xx
-
config 40x
bool "AMCC 40x"
config E200
bool "Freescale e200"
+config E500
+ bool "Freescale e500"
endchoice
config POWER4_ONLY
config 83xx
bool
-# this is temp to handle compat with arch=ppc
-config 85xx
- bool
-
-config E500
- bool
-
config PPC_FPU
bool
default y if PPC64
config SPE
bool "SPE Support"
depends on E200 || E500
- default y
---help---
This option enables kernel support for the Signal Processing
Extensions (SPE) to the PowerPC processor. The kernel currently
def_bool y
depends on PPC_STD_MMU && PPC32
-config VIRT_CPU_ACCOUNTING
- bool "Deterministic task and CPU time accounting"
- depends on PPC64
- default y
- help
- Select this option to enable more accurate task and CPU time
- accounting. This is done by reading a CPU counter on each
- kernel entry and exit and on transitions within the kernel
- between system, softirq and hardirq state, so there is a
- small performance impact. This also enables accounting of
- stolen time on logically-partitioned systems running on
- IBM POWER5-based machines.
-
- If in doubt, say Y here.
-
config SMP
depends on PPC_STD_MMU
bool "Symmetric multi-processing support"
select U3_DART
select MPIC_BROKEN_U3
select GENERIC_TBSYNC
- select PPC_970_NAP
default y
config PPC_PREP
select MPIC_BROKEN_U3
select GENERIC_TBSYNC
select PPC_UDBG_16550
- select PPC_970_NAP
default n
help
This option enables support for the Maple 970FX Evaluation Board.
select MMIO_NVRAM
select PPC_UDBG_16550
-# Systemsim configuration
-config MAMBO
- bool " IBM Full System Simulator (systemsim) support"
- default n
- ---help---
- Support booting resulting image under IBMs Full System Simulator.
-config MAMBO_DISK
- depends on MAMBO
- tristate " IBM Full System Simulator Bogus Disk Support"
- default y
- ---help---
- Provides quick access to disk images in the simulator without
- simulating a full IDE or SCSI device.
-config MAMBO_NET
- depends on MAMBO
- tristate " IBM Full System Simulator Bogus Network Support"
- default y
- ---help---
- Provides quick access to a raw ethernet device in the simulator
- without simulating any specific network device hardware.
-
config XICS
depends on PPC_PSERIES
bool
bool
default n
-config PPC_970_NAP
- bool
- default n
-
source "drivers/cpufreq/Kconfig"
config CPU_FREQ_PMAC
If in doubt, say Y here.
config TAU
- bool "On-chip CPU temperature sensor support"
+ bool "Thermal Management Support"
depends on 6xx
help
G3 and G4 processors have an on-chip temperature sensor called the
on-die temperature in /proc/cpuinfo if the cpu supports it.
Unfortunately, on some chip revisions, this sensor is very inaccurate
- and in many cases, does not work at all, so don't assume the cpu
+ and in some cases, does not work at all, so don't assume the cpu
temp is actually what /proc/cpuinfo says it is.
config TAU_INT
Say N if you are unsure.
+config ARCH_ENABLE_MEMORY_HOTPLUG
+ def_bool y
+
config KEXEC
bool "kexec system call (EXPERIMENTAL)"
depends on PPC_MULTIPLATFORM && EXPERIMENTAL
depends on PPC64
default y if SMP && PPC_PSERIES
-config NODES_SHIFT
- int
- default "4"
- depends on NEED_MULTIPLE_NODES
-
config ARCH_SELECT_MEMORY_MODEL
def_bool y
depends on PPC64
config PPC_I8259
bool
+ default y if 85xx
default n
config PPC_INDIRECT_PCI
bool
depends on PCI
- default y if 40x || 44x
+ default y if 40x || 44x || 85xx
default n
config EISA
bool
config PCI
- bool "PCI support" if 40x || CPM2 || PPC_83xx || PPC_85xx || PPC_MPC52xx || (EMBEDDED && PPC_ISERIES)
- default y if !40x && !CPM2 && !8xx && !APUS && !PPC_83xx && !PPC_85xx
+ bool "PCI support" if 40x || CPM2 || PPC_83xx || 85xx || PPC_MPC52xx || (EMBEDDED && PPC_ISERIES)
+ default y if !40x && !CPM2 && !8xx && !APUS && !PPC_83xx && !85xx
default PCI_PERMEDIA if !4xx && !CPM2 && !8xx && APUS
default PCI_QSPAN if !4xx && !CPM2 && 8xx
help
source "arch/powerpc/Kconfig.debug"
+source "kernel/vserver/Kconfig"
+
source "security/Kconfig"
config KEYS_COMPAT