#include <linux/pci.h>
#include <asm/uaccess.h>
#include <asm/atomic.h>
-#include <asm/bitops.h>
+#include <linux/bitops.h>
#include <linux/spinlock.h>
#include <asm/semaphore.h>
#include <linux/init.h>
static unsigned long board3;
static unsigned long board4;
static unsigned long controller;
-static unsigned long support_low_speed;
+static int support_low_speed;
static unsigned long modem1;
static unsigned long modem2;
static unsigned long modem3;
UPCI_AIOP_INTR_BIT_3
};
+static Byte_t RData[RDATASIZE] = {
+ 0x00, 0x09, 0xf6, 0x82,
+ 0x02, 0x09, 0x86, 0xfb,
+ 0x04, 0x09, 0x00, 0x0a,
+ 0x06, 0x09, 0x01, 0x0a,
+ 0x08, 0x09, 0x8a, 0x13,
+ 0x0a, 0x09, 0xc5, 0x11,
+ 0x0c, 0x09, 0x86, 0x85,
+ 0x0e, 0x09, 0x20, 0x0a,
+ 0x10, 0x09, 0x21, 0x0a,
+ 0x12, 0x09, 0x41, 0xff,
+ 0x14, 0x09, 0x82, 0x00,
+ 0x16, 0x09, 0x82, 0x7b,
+ 0x18, 0x09, 0x8a, 0x7d,
+ 0x1a, 0x09, 0x88, 0x81,
+ 0x1c, 0x09, 0x86, 0x7a,
+ 0x1e, 0x09, 0x84, 0x81,
+ 0x20, 0x09, 0x82, 0x7c,
+ 0x22, 0x09, 0x0a, 0x0a
+};
+
+static Byte_t RRegData[RREGDATASIZE] = {
+ 0x00, 0x09, 0xf6, 0x82, /* 00: Stop Rx processor */
+ 0x08, 0x09, 0x8a, 0x13, /* 04: Tx software flow control */
+ 0x0a, 0x09, 0xc5, 0x11, /* 08: XON char */
+ 0x0c, 0x09, 0x86, 0x85, /* 0c: XANY */
+ 0x12, 0x09, 0x41, 0xff, /* 10: Rx mask char */
+ 0x14, 0x09, 0x82, 0x00, /* 14: Compare/Ignore #0 */
+ 0x16, 0x09, 0x82, 0x7b, /* 18: Compare #1 */
+ 0x18, 0x09, 0x8a, 0x7d, /* 1c: Compare #2 */
+ 0x1a, 0x09, 0x88, 0x81, /* 20: Interrupt #1 */
+ 0x1c, 0x09, 0x86, 0x7a, /* 24: Ignore/Replace #1 */
+ 0x1e, 0x09, 0x84, 0x81, /* 28: Interrupt #2 */
+ 0x20, 0x09, 0x82, 0x7c, /* 2c: Ignore/Replace #2 */
+ 0x22, 0x09, 0x0a, 0x0a /* 30: Rx FIFO Enable */
+};
+
+static CONTROLLER_T sController[CTL_SIZE] = {
+ {-1, -1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0, 0},
+ {0, 0, 0, 0}, {-1, -1, -1, -1}, {0, 0, 0, 0}},
+ {-1, -1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0, 0},
+ {0, 0, 0, 0}, {-1, -1, -1, -1}, {0, 0, 0, 0}},
+ {-1, -1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0, 0},
+ {0, 0, 0, 0}, {-1, -1, -1, -1}, {0, 0, 0, 0}},
+ {-1, -1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0, 0},
+ {0, 0, 0, 0}, {-1, -1, -1, -1}, {0, 0, 0, 0}}
+};
+
+static Byte_t sBitMapClrTbl[8] = {
+ 0xfe, 0xfd, 0xfb, 0xf7, 0xef, 0xdf, 0xbf, 0x7f
+};
+
+static Byte_t sBitMapSetTbl[8] = {
+ 0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80
+};
+
+static int sClockPrescale = 0x14;
+
/*
* Line number is the ttySIx number (x), the Minor number. We
* assign them sequentially, starting at zero. The following
static unsigned char GetLineNumber(int ctrl, int aiop, int ch);
static unsigned char SetLineNumber(int ctrl, int aiop, int ch);
static void rp_start(struct tty_struct *tty);
+static int sInitChan(CONTROLLER_T * CtlP, CHANNEL_T * ChP, int AiopNum,
+ int ChanNum);
+static void sSetInterfaceMode(CHANNEL_T * ChP, Byte_t mode);
+static void sFlushRxFIFO(CHANNEL_T * ChP);
+static void sFlushTxFIFO(CHANNEL_T * ChP);
+static void sEnInterrupts(CHANNEL_T * ChP, Word_t Flags);
+static void sDisInterrupts(CHANNEL_T * ChP, Word_t Flags);
+static void sModemReset(CONTROLLER_T * CtlP, int chan, int on);
+static void sPCIModemReset(CONTROLLER_T * CtlP, int chan, int on);
+static int sWriteTxPrioByte(CHANNEL_T * ChP, Byte_t Data);
+static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
+ ByteIO_t * AiopIOList, int AiopIOListSize,
+ WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
+ int PeriodicOnly, int altChanRingIndicator,
+ int UPCIRingInd);
+static int sInitController(CONTROLLER_T * CtlP, int CtlNum, ByteIO_t MudbacIO,
+ ByteIO_t * AiopIOList, int AiopIOListSize,
+ int IRQNum, Byte_t Frequency, int PeriodicOnly);
+static int sReadAiopID(ByteIO_t io);
+static int sReadAiopNumChan(WordIO_t io);
-#ifdef MODULE
MODULE_AUTHOR("Theodore Ts'o");
MODULE_DESCRIPTION("Comtrol RocketPort driver");
-MODULE_PARM(board1, "i");
+module_param(board1, ulong, 0);
MODULE_PARM_DESC(board1, "I/O port for (ISA) board #1");
-MODULE_PARM(board2, "i");
+module_param(board2, ulong, 0);
MODULE_PARM_DESC(board2, "I/O port for (ISA) board #2");
-MODULE_PARM(board3, "i");
+module_param(board3, ulong, 0);
MODULE_PARM_DESC(board3, "I/O port for (ISA) board #3");
-MODULE_PARM(board4, "i");
+module_param(board4, ulong, 0);
MODULE_PARM_DESC(board4, "I/O port for (ISA) board #4");
-MODULE_PARM(controller, "i");
+module_param(controller, ulong, 0);
MODULE_PARM_DESC(controller, "I/O port for (ISA) rocketport controller");
-MODULE_PARM(support_low_speed, "i");
+module_param(support_low_speed, bool, 0);
MODULE_PARM_DESC(support_low_speed, "1 means support 50 baud, 0 means support 460400 baud");
-MODULE_PARM(modem1, "i");
+module_param(modem1, ulong, 0);
MODULE_PARM_DESC(modem1, "1 means (ISA) board #1 is a RocketModem");
-MODULE_PARM(modem2, "i");
+module_param(modem2, ulong, 0);
MODULE_PARM_DESC(modem2, "1 means (ISA) board #2 is a RocketModem");
-MODULE_PARM(modem3, "i");
+module_param(modem3, ulong, 0);
MODULE_PARM_DESC(modem3, "1 means (ISA) board #3 is a RocketModem");
-MODULE_PARM(modem4, "i");
+module_param(modem4, ulong, 0);
MODULE_PARM_DESC(modem4, "1 means (ISA) board #4 is a RocketModem");
-MODULE_PARM(pc104_1, "1-8i");
+module_param_array(pc104_1, ulong, NULL, 0);
MODULE_PARM_DESC(pc104_1, "set interface types for ISA(PC104) board #1 (e.g. pc104_1=232,232,485,485,...");
-MODULE_PARM(pc104_2, "1-8i");
+module_param_array(pc104_2, ulong, NULL, 0);
MODULE_PARM_DESC(pc104_2, "set interface types for ISA(PC104) board #2 (e.g. pc104_2=232,232,485,485,...");
-MODULE_PARM(pc104_3, "1-8i");
+module_param_array(pc104_3, ulong, NULL, 0);
MODULE_PARM_DESC(pc104_3, "set interface types for ISA(PC104) board #3 (e.g. pc104_3=232,232,485,485,...");
-MODULE_PARM(pc104_4, "1-8i");
+module_param_array(pc104_4, ulong, NULL, 0);
MODULE_PARM_DESC(pc104_4, "set interface types for ISA(PC104) board #4 (e.g. pc104_4=232,232,485,485,...");
-int rp_init(void);
+static int rp_init(void);
static void rp_cleanup_module(void);
module_init(rp_init);
module_exit(rp_cleanup_module);
-#endif
-#ifdef MODULE_LICENSE
MODULE_LICENSE("Dual BSD/GPL");
-#endif
/*************************************************************************/
/* Module code starts here */
CHANNEL_t * cp, unsigned int ChanStatus)
{
unsigned int CharNStat;
- int ToRecv, wRecv, space = 0, count;
+ int ToRecv, wRecv, space;
unsigned char *cbuf;
- char *fbuf;
- struct tty_ldisc *ld;
-
- ld = tty_ldisc_ref(tty);
ToRecv = sGetRxCnt(cp);
- if (ld)
- space = ld->receive_room(tty);
- if (space > 2 * TTY_FLIPBUF_SIZE)
- space = 2 * TTY_FLIPBUF_SIZE;
- cbuf = tty->flip.char_buf;
- fbuf = tty->flip.flag_buf;
- count = 0;
#ifdef ROCKET_DEBUG_INTR
- printk(KERN_INFO "rp_do_receive(%d, %d)...", ToRecv, space);
+ printk(KERN_INFO "rp_do_receive(%d)...", ToRecv);
#endif
-
- /*
- * determine how many we can actually read in. If we can't
- * read any in then we have a software overrun condition.
- */
- if (ToRecv > space)
- ToRecv = space;
-
- if (ToRecv <= 0)
+ if (ToRecv == 0)
return;
/*
info->read_status_mask);
#endif
while (ToRecv) {
+ char flag;
+
CharNStat = sInW(sGetTxRxDataIO(cp));
#ifdef ROCKET_DEBUG_RECEIVE
printk(KERN_INFO "%x...", CharNStat);
}
CharNStat &= info->read_status_mask;
if (CharNStat & STMBREAKH)
- *fbuf++ = TTY_BREAK;
+ flag = TTY_BREAK;
else if (CharNStat & STMPARITYH)
- *fbuf++ = TTY_PARITY;
+ flag = TTY_PARITY;
else if (CharNStat & STMFRAMEH)
- *fbuf++ = TTY_FRAME;
+ flag = TTY_FRAME;
else if (CharNStat & STMRCVROVRH)
- *fbuf++ = TTY_OVERRUN;
+ flag = TTY_OVERRUN;
else
- *fbuf++ = 0;
- *cbuf++ = CharNStat & 0xff;
- count++;
+ flag = TTY_NORMAL;
+ tty_insert_flip_char(tty, CharNStat & 0xff, flag);
ToRecv--;
}
* characters at time by doing repeated word IO
* transfer.
*/
+ space = tty_prepare_flip_string(tty, &cbuf, ToRecv);
+ if (space < ToRecv) {
+#ifdef ROCKET_DEBUG_RECEIVE
+ printk(KERN_INFO "rp_do_receive:insufficient space ToRecv=%d space=%d\n", ToRecv, space);
+#endif
+ if (space <= 0)
+ return;
+ ToRecv = space;
+ }
wRecv = ToRecv >> 1;
if (wRecv)
sInStrW(sGetTxRxDataIO(cp), (unsigned short *) cbuf, wRecv);
if (ToRecv & 1)
cbuf[ToRecv - 1] = sInB(sGetTxRxDataIO(cp));
- memset(fbuf, 0, ToRecv);
- cbuf += ToRecv;
- fbuf += ToRecv;
- count += ToRecv;
}
/* Push the data up to the tty layer */
- ld->receive_buf(tty, tty->flip.char_buf, tty->flip.flag_buf, count);
- tty_ldisc_deref(ld);
+ tty_flip_buffer_push(tty);
}
/*
* user mode into the driver (exception handler). *info CD manipulation is spinlock protected.
*/
static void configure_r_port(struct r_port *info,
- struct termios *old_termios)
+ struct ktermios *old_termios)
{
unsigned cflag;
unsigned long flags;
/*
* Info->count is now 1; so it's safe to sleep now.
*/
- info->session = current->signal->session;
+ info->session = process_session(current);
info->pgrp = process_group(current);
if ((info->flags & ROCKET_INITIALIZED) == 0) {
if (info->blocked_open) {
if (info->close_delay) {
- current->state = TASK_INTERRUPTIBLE;
- schedule_timeout(info->close_delay);
+ msleep_interruptible(jiffies_to_msecs(info->close_delay));
}
wake_up_interruptible(&info->open_wait);
} else {
}
static void rp_set_termios(struct tty_struct *tty,
- struct termios *old_termios)
+ struct ktermios *old_termios)
{
struct r_port *info = (struct r_port *) tty->driver_data;
CHANNEL_t *cp;
#ifdef ROCKET_DEBUG_WAIT_UNTIL_SENT
printk(KERN_INFO "txcnt = %d (jiff=%lu,check=%d)...", txcnt, jiffies, check_time);
#endif
- current->state = TASK_INTERRUPTIBLE;
- schedule_timeout(check_time);
+ msleep_interruptible(jiffies_to_msecs(check_time));
if (signal_pending(current))
break;
}
* or get control of the CPU if the copy_from_user() blocks due to a page fault (swapped out).
* Spinlocks protect the info xmit members.
*/
-static int rp_write(struct tty_struct *tty, int from_user,
+static int rp_write(struct tty_struct *tty,
const unsigned char *buf, int count)
{
struct r_port *info = (struct r_port *) tty->driver_data;
if (!tty->stopped && !tty->hw_stopped && info->xmit_cnt == 0 && info->xmit_fifo_room > 0) {
c = min(count, info->xmit_fifo_room);
b = buf;
- if (from_user) {
- if (copy_from_user(info->xmit_buf, buf, c)) {
- retval = -EFAULT;
- goto end;
- }
- if (info->tty == 0)
- goto end;
- b = info->xmit_buf;
- c = min(c, info->xmit_fifo_room);
- }
/* Push data into FIFO, 2 bytes at a time */
sOutStrW(sGetTxRxDataIO(cp), (unsigned short *) b, c / 2);
break;
b = buf;
- if (from_user) {
- if (copy_from_user(info->xmit_buf + info->xmit_head, b, c)) {
- retval = -EFAULT;
- goto end_intr;
- } else {
- memcpy(info->xmit_buf + info->xmit_head, b, c);
- }
- }
+ memcpy(info->xmit_buf + info->xmit_head, b, c);
spin_lock_irqsave(&info->slock, flags);
info->xmit_head =
retval += c;
}
-end_intr:
if ((retval > 0) && !tty->stopped && !tty->hw_stopped)
set_bit((info->aiop * 8) + info->chan, (void *) &xmit_flags[info->board]);
* init's aiopic and serial port hardware.
* Inputs: i is the board number (0-n)
*/
-__init int register_PCI(int i, struct pci_dev *dev)
+static __init int register_PCI(int i, struct pci_dev *dev)
{
int num_aiops, aiop, max_num_aiops, num_chan, chan;
unsigned int aiopio[MAX_AIOPS_PER_BOARD];
int count = 0;
/* Work through the PCI device list, pulling out ours */
- while ((dev = pci_find_device(PCI_VENDOR_ID_RP, PCI_ANY_ID, dev))) {
+ while ((dev = pci_get_device(PCI_VENDOR_ID_RP, PCI_ANY_ID, dev))) {
if (register_PCI(count + boards_found, dev))
count++;
}
return (1);
}
-static struct tty_operations rocket_ops = {
+static const struct tty_operations rocket_ops = {
.open = rp_open,
.close = rp_close,
.write = rp_write,
/*
* The module "startup" routine; it's run when the module is loaded.
*/
-int __init rp_init(void)
+static int __init rp_init(void)
{
int retval, pci_boards_found, isa_boards_found, i;
*/
rocket_driver->owner = THIS_MODULE;
- rocket_driver->flags = TTY_DRIVER_NO_DEVFS;
- rocket_driver->devfs_name = "tts/R";
+ rocket_driver->flags = TTY_DRIVER_DYNAMIC_DEV;
rocket_driver->name = "ttyR";
rocket_driver->driver_name = "Comtrol RocketPort";
rocket_driver->major = TTY_ROCKET_MAJOR;
rocket_driver->init_termios = tty_std_termios;
rocket_driver->init_termios.c_cflag =
B9600 | CS8 | CREAD | HUPCL | CLOCAL;
+ rocket_driver->init_termios.c_ispeed = 9600;
+ rocket_driver->init_termios.c_ospeed = 9600;
#ifdef ROCKET_SOFT_FLOW
- rocket_driver->flags |= TTY_DRIVER_REAL_RAW | TTY_DRIVER_NO_DEVFS;
+ rocket_driver->flags |= TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
#endif
tty_set_operations(rocket_driver, &rocket_ops);
return 0;
}
-#ifdef MODULE
static void rp_cleanup_module(void)
{
"rocketport driver\n", -retval);
put_tty_driver(rocket_driver);
- for (i = 0; i < MAX_RP_PORTS; i++) {
- if (rp_table[i])
- kfree(rp_table[i]);
- }
+ for (i = 0; i < MAX_RP_PORTS; i++)
+ kfree(rp_table[i]);
for (i = 0; i < NUM_BOARDS; i++) {
if (rcktpt_io_addr[i] <= 0 || is_PCI[i])
if (controller)
release_region(controller, 4);
}
-#endif
-
-/***********************************************************************
- Copyright 1994 Comtrol Corporation.
- All Rights Reserved.
-
-The following source code is subject to Comtrol Corporation's
-Developer's License Agreement.
-
-This source code is protected by United States copyright law and
-international copyright treaties.
-
-This source code may only be used to develop software products that
-will operate with Comtrol brand hardware.
-
-You may not reproduce nor distribute this source code in its original
-form but must produce a derivative work which includes portions of
-this source code only.
-
-The portions of this source code which you use in your derivative
-work must bear Comtrol's copyright notice:
-
- Copyright 1994 Comtrol Corporation.
-
-***********************************************************************/
-
-#ifndef TRUE
-#define TRUE 1
-#endif
-
-#ifndef FALSE
-#define FALSE 0
-#endif
-
-static Byte_t RData[RDATASIZE] = {
- 0x00, 0x09, 0xf6, 0x82,
- 0x02, 0x09, 0x86, 0xfb,
- 0x04, 0x09, 0x00, 0x0a,
- 0x06, 0x09, 0x01, 0x0a,
- 0x08, 0x09, 0x8a, 0x13,
- 0x0a, 0x09, 0xc5, 0x11,
- 0x0c, 0x09, 0x86, 0x85,
- 0x0e, 0x09, 0x20, 0x0a,
- 0x10, 0x09, 0x21, 0x0a,
- 0x12, 0x09, 0x41, 0xff,
- 0x14, 0x09, 0x82, 0x00,
- 0x16, 0x09, 0x82, 0x7b,
- 0x18, 0x09, 0x8a, 0x7d,
- 0x1a, 0x09, 0x88, 0x81,
- 0x1c, 0x09, 0x86, 0x7a,
- 0x1e, 0x09, 0x84, 0x81,
- 0x20, 0x09, 0x82, 0x7c,
- 0x22, 0x09, 0x0a, 0x0a
-};
-
-static Byte_t RRegData[RREGDATASIZE] = {
- 0x00, 0x09, 0xf6, 0x82, /* 00: Stop Rx processor */
- 0x08, 0x09, 0x8a, 0x13, /* 04: Tx software flow control */
- 0x0a, 0x09, 0xc5, 0x11, /* 08: XON char */
- 0x0c, 0x09, 0x86, 0x85, /* 0c: XANY */
- 0x12, 0x09, 0x41, 0xff, /* 10: Rx mask char */
- 0x14, 0x09, 0x82, 0x00, /* 14: Compare/Ignore #0 */
- 0x16, 0x09, 0x82, 0x7b, /* 18: Compare #1 */
- 0x18, 0x09, 0x8a, 0x7d, /* 1c: Compare #2 */
- 0x1a, 0x09, 0x88, 0x81, /* 20: Interrupt #1 */
- 0x1c, 0x09, 0x86, 0x7a, /* 24: Ignore/Replace #1 */
- 0x1e, 0x09, 0x84, 0x81, /* 28: Interrupt #2 */
- 0x20, 0x09, 0x82, 0x7c, /* 2c: Ignore/Replace #2 */
- 0x22, 0x09, 0x0a, 0x0a /* 30: Rx FIFO Enable */
-};
-
-CONTROLLER_T sController[CTL_SIZE] = {
- {-1, -1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0, 0},
- {0, 0, 0, 0}, {-1, -1, -1, -1}, {0, 0, 0, 0}},
- {-1, -1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0, 0},
- {0, 0, 0, 0}, {-1, -1, -1, -1}, {0, 0, 0, 0}},
- {-1, -1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0, 0},
- {0, 0, 0, 0}, {-1, -1, -1, -1}, {0, 0, 0, 0}},
- {-1, -1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0, 0},
- {0, 0, 0, 0}, {-1, -1, -1, -1}, {0, 0, 0, 0}}
-};
-
-Byte_t sBitMapClrTbl[8] = {
- 0xfe, 0xfd, 0xfb, 0xf7, 0xef, 0xdf, 0xbf, 0x7f
-};
-
-Byte_t sBitMapSetTbl[8] = {
- 0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80
-};
-
-int sClockPrescale = 0x14;
/***************************************************************************
Function: sInitController
FREQ_4HZ - 4 Hertz
If IRQNum is set to 0 the Frequency parameter is
overidden, it is forced to a value of FREQ_DIS.
- int PeriodicOnly: TRUE if all interrupts except the periodic
+ int PeriodicOnly: 1 if all interrupts except the periodic
interrupt are to be blocked.
- FALSE is both the periodic interrupt and
+ 0 is both the periodic interrupt and
other channel interrupts are allowed.
If IRQNum is set to 0 the PeriodicOnly parameter is
- overidden, it is forced to a value of FALSE.
+ overidden, it is forced to a value of 0.
Return: int: Number of AIOPs on the controller, or CTLID_NULL if controller
initialization failed.
Comments:
If periodic interrupts are to be disabled but AIOP interrupts
- are allowed, set Frequency to FREQ_DIS and PeriodicOnly to FALSE.
+ are allowed, set Frequency to FREQ_DIS and PeriodicOnly to 0.
If interrupts are to be completely disabled set IRQNum to 0.
- Setting Frequency to FREQ_DIS and PeriodicOnly to TRUE is an
+ Setting Frequency to FREQ_DIS and PeriodicOnly to 1 is an
invalid combination.
This function performs initialization of global interrupt modes,
After this function all AIOPs on the controller are disabled,
they can be enabled with sEnAiop().
*/
-int sInitController(CONTROLLER_T * CtlP, int CtlNum, ByteIO_t MudbacIO,
- ByteIO_t * AiopIOList, int AiopIOListSize, int IRQNum,
- Byte_t Frequency, int PeriodicOnly)
+static int sInitController(CONTROLLER_T * CtlP, int CtlNum, ByteIO_t MudbacIO,
+ ByteIO_t * AiopIOList, int AiopIOListSize,
+ int IRQNum, Byte_t Frequency, int PeriodicOnly)
{
int i;
ByteIO_t io;
FREQ_4HZ - 4 Hertz
If IRQNum is set to 0 the Frequency parameter is
overidden, it is forced to a value of FREQ_DIS.
- int PeriodicOnly: TRUE if all interrupts except the periodic
+ int PeriodicOnly: 1 if all interrupts except the periodic
interrupt are to be blocked.
- FALSE is both the periodic interrupt and
+ 0 is both the periodic interrupt and
other channel interrupts are allowed.
If IRQNum is set to 0 the PeriodicOnly parameter is
- overidden, it is forced to a value of FALSE.
+ overidden, it is forced to a value of 0.
Return: int: Number of AIOPs on the controller, or CTLID_NULL if controller
initialization failed.
Comments:
If periodic interrupts are to be disabled but AIOP interrupts
- are allowed, set Frequency to FREQ_DIS and PeriodicOnly to FALSE.
+ are allowed, set Frequency to FREQ_DIS and PeriodicOnly to 0.
If interrupts are to be completely disabled set IRQNum to 0.
- Setting Frequency to FREQ_DIS and PeriodicOnly to TRUE is an
+ Setting Frequency to FREQ_DIS and PeriodicOnly to 1 is an
invalid combination.
This function performs initialization of global interrupt modes,
After this function all AIOPs on the controller are disabled,
they can be enabled with sEnAiop().
*/
-int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
- ByteIO_t * AiopIOList, int AiopIOListSize,
- WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
- int PeriodicOnly, int altChanRingIndicator,
- int UPCIRingInd)
+static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
+ ByteIO_t * AiopIOList, int AiopIOListSize,
+ WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
+ int PeriodicOnly, int altChanRingIndicator,
+ int UPCIRingInd)
{
int i;
ByteIO_t io;
Warnings: No context switches are allowed while executing this function.
*/
-int sReadAiopID(ByteIO_t io)
+static int sReadAiopID(ByteIO_t io)
{
Byte_t AiopID; /* ID byte from AIOP */
AIOP, otherwise it is an 8 channel.
Warnings: No context switches are allowed while executing this function.
*/
-int sReadAiopNumChan(WordIO_t io)
+static int sReadAiopNumChan(WordIO_t io)
{
Word_t x;
static Byte_t R[4] = { 0x00, 0x00, 0x34, 0x12 };
CHANNEL_T *ChP; Ptr to channel structure
int AiopNum; AIOP number within controller
int ChanNum; Channel number within AIOP
-Return: int: TRUE if initialization succeeded, FALSE if it fails because channel
+Return: int: 1 if initialization succeeded, 0 if it fails because channel
number exceeds number of channels available in AIOP.
Comments: This function must be called before a channel can be used.
Warnings: No range checking on any of the parameters is done.
No context switches are allowed while executing this function.
*/
-int sInitChan(CONTROLLER_T * CtlP, CHANNEL_T * ChP, int AiopNum,
- int ChanNum)
+static int sInitChan(CONTROLLER_T * CtlP, CHANNEL_T * ChP, int AiopNum,
+ int ChanNum)
{
int i;
WordIO_t AiopIO;
int brd9600;
if (ChanNum >= CtlP->AiopNumChan[AiopNum])
- return (FALSE); /* exceeds num chans in AIOP */
+ return 0; /* exceeds num chans in AIOP */
/* Channel, AIOP, and controller identifiers */
ChP->CtlP = CtlP;
ChP->TxPrioBuf = ChOff + _TXP_BUF;
sEnRxProcessor(ChP); /* start the Rx processor */
- return (TRUE);
+ return 1;
}
/***************************************************************************
After calling this function a delay of 4 uS is required to ensure
that the receive processor is no longer processing this channel.
*/
-void sStopRxProcessor(CHANNEL_T * ChP)
+static void sStopRxProcessor(CHANNEL_T * ChP)
{
Byte_t R[4];
this function.
Warnings: No context switches are allowed while executing this function.
*/
-void sFlushRxFIFO(CHANNEL_T * ChP)
+static void sFlushRxFIFO(CHANNEL_T * ChP)
{
int i;
Byte_t Ch; /* channel number within AIOP */
- int RxFIFOEnabled; /* TRUE if Rx FIFO enabled */
+ int RxFIFOEnabled; /* 1 if Rx FIFO enabled */
if (sGetRxCnt(ChP) == 0) /* Rx FIFO empty */
return; /* don't need to flush */
- RxFIFOEnabled = FALSE;
+ RxFIFOEnabled = 0;
if (ChP->R[0x32] == 0x08) { /* Rx FIFO is enabled */
- RxFIFOEnabled = TRUE;
+ RxFIFOEnabled = 1;
sDisRxFIFO(ChP); /* disable it */
for (i = 0; i < 2000 / 200; i++) /* delay 2 uS to allow proc to disable FIFO */
sInB(ChP->IntChan); /* depends on bus i/o timing */
this function.
Warnings: No context switches are allowed while executing this function.
*/
-void sFlushTxFIFO(CHANNEL_T * ChP)
+static void sFlushTxFIFO(CHANNEL_T * ChP)
{
int i;
Byte_t Ch; /* channel number within AIOP */
- int TxEnabled; /* TRUE if transmitter enabled */
+ int TxEnabled; /* 1 if transmitter enabled */
if (sGetTxCnt(ChP) == 0) /* Tx FIFO empty */
return; /* don't need to flush */
- TxEnabled = FALSE;
+ TxEnabled = 0;
if (ChP->TxControl[3] & TX_ENABLE) {
- TxEnabled = TRUE;
+ TxEnabled = 1;
sDisTransmit(ChP); /* disable transmitter */
}
sStopRxProcessor(ChP); /* stop Rx processor */
Warnings: No context switches are allowed while executing this function.
*/
-int sWriteTxPrioByte(CHANNEL_T * ChP, Byte_t Data)
+static int sWriteTxPrioByte(CHANNEL_T * ChP, Byte_t Data)
{
Byte_t DWBuf[4]; /* buffer for double word writes */
Word_t *WordPtr; /* must be far because Win SS != DS */
enable channel interrupts. This would allow the global interrupt
status register to be used to determine which AIOPs need service.
*/
-void sEnInterrupts(CHANNEL_T * ChP, Word_t Flags)
+static void sEnInterrupts(CHANNEL_T * ChP, Word_t Flags)
{
Byte_t Mask; /* Interrupt Mask Register */
this channel's bit from being set in the AIOP's Interrupt Channel
Register.
*/
-void sDisInterrupts(CHANNEL_T * ChP, Word_t Flags)
+static void sDisInterrupts(CHANNEL_T * ChP, Word_t Flags)
{
Byte_t Mask; /* Interrupt Mask Register */
}
}
-void sSetInterfaceMode(CHANNEL_T * ChP, Byte_t mode)
+static void sSetInterfaceMode(CHANNEL_T * ChP, Byte_t mode)
{
sOutB(ChP->CtlP->AiopIO[2], (mode & 0x18) | ChP->ChanNum);
}
* Not an official SSCI function, but how to reset RocketModems.
* ISA bus version
*/
-void sModemReset(CONTROLLER_T * CtlP, int chan, int on)
+static void sModemReset(CONTROLLER_T * CtlP, int chan, int on)
{
ByteIO_t addr;
Byte_t val;
* Not an official SSCI function, but how to reset RocketModems.
* PCI bus version
*/
-void sPCIModemReset(CONTROLLER_T * CtlP, int chan, int on)
+static void sPCIModemReset(CONTROLLER_T * CtlP, int chan, int on)
{
ByteIO_t addr;