# Andre Hedrick <andre@linux-ide.org>
#
+if BLOCK
+
menu "ATA/ATAPI/MFM/RLL support"
config IDE
if IDE
-config IDE_MAX_HWIFS
+config IDE_MAX_HWIFS
int "Max IDE interfaces"
- depends on ALPHA || SUPERH
+ depends on ALPHA || SUPERH || IA64 || EMBEDDED
default 4
help
This is the maximum number of IDE hardware interfaces that will
config IDEDISK_MULTI_MODE
bool "Use multi-mode by default"
- depends on BLK_DEV_IDEDISK
help
If you get this error, try to say Y here:
tristate "PCMCIA IDE support"
depends on PCMCIA
help
- Support for outboard IDE disks, tape drives, and CD-ROM drives
- connected through a PCMCIA card.
+ Support for Compact Flash cards, outboard IDE disks, tape drives,
+ and CD-ROM drives connected through a PCMCIA card.
config BLK_DEV_IDECD
tristate "Include IDE/ATAPI CDROM support"
help
This is a direct raw access to the media. It is a complex but
elegant solution to test and validate the domain of the hardware and
- perform below the driver data recover if needed. This is the most
+ perform below the driver data recovery if needed. This is the most
basic form of media-forensics.
If you are unsure, say N here.
Linux. This may slow disk throughput by a few percent, but at least
things will operate 100% reliably.
-config BLK_DEV_SL82C105
- tristate "Winbond SL82c105 support"
- depends on PCI && (PPC || ARM) && BLK_DEV_IDEPCI
- help
- If you have a Winbond SL82c105 IDE controller, say Y here to enable
- special configuration for this chip. This is common on various CHRP
- motherboards, but could be used elsewhere. If in doubt, say Y.
-
config BLK_DEV_IDEDMA_PCI
bool "Generic PCI bus-master DMA support"
depends on PCI && BLK_DEV_IDEPCI
tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
depends on EXPERIMENTAL
help
- Include support for PIO tuning an virtual DMA on the Cyrix MediaGX
+ Include support for PIO tuning and virtual DMA on the Cyrix MediaGX
5510/5520 chipset. This will automatically be detected and
configured if found.
It is safe to say Y to this question.
+config BLK_DEV_CS5535
+ tristate "AMD CS5535 chipset support"
+ depends on X86 && !X86_64
+ help
+ Include support for UDMA on the NSC/AMD CS5535 companion chipset.
+ This will automatically be detected and configured if found.
+
+ It is safe to say Y to this question.
+
config BLK_DEV_HPT34X
tristate "HPT34X chipset support"
help
ide-probe at boot. It is reported to support DVD II drives, by the
manufacturer.
+config BLK_DEV_JMICRON
+ tristate "JMicron JMB36x support"
+ help
+ Basic support for the JMicron ATA controllers. For full support
+ use the libata drivers.
+
config BLK_DEV_SC1200
tristate "National SCx200 chipset support"
help
the kernel to change PIO, DMA and UDMA speeds and to configure
the chip to optimum performance.
-config BLK_DEV_IT8172
- bool "IT8172 IDE support"
- depends on (MIPS_ITE8172 || MIPS_IVR)
+config BLK_DEV_IT821X
+ tristate "IT821X IDE support"
help
- Say Y here to support the on-board IDE controller on the Integrated
- Technology Express, Inc. ITE8172 SBC. Vendor page at
- <http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the
- board at <http://www.mvista.com/partners/semiconductor/ite.html>.
+ This driver adds support for the ITE 8211 IDE controller and the
+ IT 8212 IDE RAID controller in both RAID and pass-through mode.
config BLK_DEV_NS87415
tristate "NS87415 chipset support"
help
This driver adds detection and support for the NS87415 chip
- (used in SPARC64, among others).
+ (used mainly on SPARC64 and PA-RISC machines).
Please read the comments at the top of <file:drivers/ide/pci/ns87415.c>.
It was originally designed for the PDC20246/Ultra33, whose BIOS will
only setup UDMA on the first two PDC20246 cards. It has also been
- used succesfully on a PDC20265/Ultra100, allowing use of UDMA modes
+ used successfully on a PDC20265/Ultra100, allowing use of UDMA modes
when the PDC20265 BIOS has been disabled (for faster boot up).
Please read the comments at the top of
config BLK_DEV_PDC202XX_NEW
tristate "PROMISE PDC202{68|69|70|71|75|76|77} support"
-# FIXME - probably wants to be one for old and for new
-config PDC202XX_FORCE
- bool "Enable controller even if disabled by BIOS"
- depends on BLK_DEV_PDC202XX_NEW
- help
- Enable the PDC202xx controller even if it has been disabled in the BIOS setup.
-
config BLK_DEV_SVWKS
tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support"
help
chipsets.
config BLK_DEV_SGIIOC4
- tristate "Silicon Graphics IOC4 chipset support"
- depends on IA64_SGI_SN2 || IA64_GENERIC
+ tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support"
+ depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4
+ select IDEPCI_SHARE_IRQ
help
This driver adds PIO & MultiMode DMA-2 support for the SGI IOC4
chipset, which has one channel and can support two devices.
Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>.
+config BLK_DEV_SL82C105
+ tristate "Winbond SL82c105 support"
+ depends on (PPC || ARM)
+ help
+ If you have a Winbond SL82c105 IDE controller, say Y here to enable
+ special configuration for this chip. This is common on various CHRP
+ motherboards, but could be used elsewhere. If in doubt, say Y.
+
config BLK_DEV_SLC90E66
tristate "SLC90E66 chipset support"
help
- This driver ensures (U)DMA support for Victroy66 SouthBridges for
+ This driver ensures (U)DMA support for Victory66 SouthBridges for
SMsC with Intel NorthBridges. This is an Ultra66 based chipset.
The nice thing about it is that you can mix Ultra/DMA/PIO devices
and it will handle timing cycles. Since this is an improved
config BLK_DEV_IDEDMA_PMAC
bool "PowerMac IDE DMA support"
depends on BLK_DEV_IDE_PMAC
+ select BLK_DEV_IDEDMA_PCI
help
This option allows the driver for the built-in IDE controller on
Power Macintoshes and PowerBooks to use DMA (direct memory access)
to transfer data to and from memory. Saying Y is safe and improves
performance.
-config BLK_DEV_IDE_PMAC_BLINK
- bool "Blink laptop LED on drive activity"
- depends on BLK_DEV_IDE_PMAC && ADB_PMU
- help
- This option enables the use of the sleep LED as a hard drive
- activity LED.
+config BLK_DEV_IDE_SWARM
+ tristate "IDE for Sibyte evaluation boards"
+ depends on SIBYTE_SB1xxx_SOC
+
+config BLK_DEV_IDE_AU1XXX
+ bool "IDE for AMD Alchemy Au1200"
+ depends on SOC_AU1200
+choice
+ prompt "IDE Mode for AMD Alchemy Au1200"
+ default CONFIG_BLK_DEV_IDE_AU1XXX_PIO_DBDMA
+ depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
+
+config BLK_DEV_IDE_AU1XXX_PIO_DBDMA
+ bool "PIO+DbDMA IDE for AMD Alchemy Au1200"
+
+config BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
+ bool "MDMA2+DbDMA IDE for AMD Alchemy Au1200"
+ depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
+endchoice
+
+config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
+ int "Maximum transfer size (KB) per request (up to 128)"
+ default "128"
+ depends on BLK_DEV_IDE_AU1XXX
config IDE_ARM
def_bool ARM && (ARCH_A5K || ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
config BLK_DEV_MPC8xx_IDE
bool "MPC8xx IDE support"
- depends on 8xx
+ depends on 8xx && IDE=y && BLK_DEV_IDE=y
help
This option provides support for IDE on Motorola MPC8xx Systems.
Please see 'Type of MPC8xx IDE interface' for details.
endif
config BLK_DEV_IDEDMA
- def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS
+ def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
config IDEDMA_IVB
bool "IGNORE word93 Validation BITS"
in that mode with an 80c ribbon.
If you are experiencing compatibility or performance problems, you
- MAY try to answering Y here. However, it does not necessarily solve
+ MAY try to answer Y here. However, it does not necessarily solve
any of your problems, it could even cause more of them.
It is normally safe to answer Y; however, the default is N.
endif
endmenu
+
+endif
git://git.onelab.eu / linux-2.6.git / blobdiff