* b: if a hw mac address already is there, eth0's hw mac address
* will then be set from bond0.
*
- * v0.1 - first working version.
- * v0.2 - changed stats to be calculated by summing slaves stats.
- *
- * Changes:
- * Arnaldo Carvalho de Melo <acme@conectiva.com.br>
- * - fix leaks on failure at bond_init
- *
- * 2000/09/30 - Willy Tarreau <willy at meta-x.org>
- * - added trivial code to release a slave device.
- * - fixed security bug (CAP_NET_ADMIN not checked)
- * - implemented MII link monitoring to disable dead links :
- * All MII capable slaves are checked every <miimon> milliseconds
- * (100 ms seems good). This value can be changed by passing it to
- * insmod. A value of zero disables the monitoring (default).
- * - fixed an infinite loop in bond_xmit_roundrobin() when there's no
- * good slave.
- * - made the code hopefully SMP safe
- *
- * 2000/10/03 - Willy Tarreau <willy at meta-x.org>
- * - optimized slave lists based on relevant suggestions from Thomas Davis
- * - implemented active-backup method to obtain HA with two switches:
- * stay as long as possible on the same active interface, while we
- * also monitor the backup one (MII link status) because we want to know
- * if we are able to switch at any time. ( pass "mode=1" to insmod )
- * - lots of stress testings because we need it to be more robust than the
- * wires ! :->
- *
- * 2000/10/09 - Willy Tarreau <willy at meta-x.org>
- * - added up and down delays after link state change.
- * - optimized the slaves chaining so that when we run forward, we never
- * repass through the bond itself, but we can find it by searching
- * backwards. Renders the deletion more difficult, but accelerates the
- * scan.
- * - smarter enslaving and releasing.
- * - finer and more robust SMP locking
- *
- * 2000/10/17 - Willy Tarreau <willy at meta-x.org>
- * - fixed two potential SMP race conditions
- *
- * 2000/10/18 - Willy Tarreau <willy at meta-x.org>
- * - small fixes to the monitoring FSM in case of zero delays
- * 2000/11/01 - Willy Tarreau <willy at meta-x.org>
- * - fixed first slave not automatically used in trunk mode.
- * 2000/11/10 : spelling of "EtherChannel" corrected.
- * 2000/11/13 : fixed a race condition in case of concurrent accesses to ioctl().
- * 2000/12/16 : fixed improper usage of rtnl_exlock_nowait().
- *
- * 2001/1/3 - Chad N. Tindel <ctindel at ieee dot org>
- * - The bonding driver now simulates MII status monitoring, just like
- * a normal network device. It will show that the link is down iff
- * every slave in the bond shows that their links are down. If at least
- * one slave is up, the bond's MII status will appear as up.
- *
- * 2001/2/7 - Chad N. Tindel <ctindel at ieee dot org>
- * - Applications can now query the bond from user space to get
- * information which may be useful. They do this by calling
- * the BOND_INFO_QUERY ioctl. Once the app knows how many slaves
- * are in the bond, it can call the BOND_SLAVE_INFO_QUERY ioctl to
- * get slave specific information (# link failures, etc). See
- * <linux/if_bonding.h> for more details. The structs of interest
- * are ifbond and ifslave.
- *
- * 2001/4/5 - Chad N. Tindel <ctindel at ieee dot org>
- * - Ported to 2.4 Kernel
- *
- * 2001/5/2 - Jeffrey E. Mast <jeff at mastfamily dot com>
- * - When a device is detached from a bond, the slave device is no longer
- * left thinking that is has a master.
- *
- * 2001/5/16 - Jeffrey E. Mast <jeff at mastfamily dot com>
- * - memset did not appropriately initialized the bond rw_locks. Used
- * rwlock_init to initialize to unlocked state to prevent deadlock when
- * first attempting a lock
- * - Called SET_MODULE_OWNER for bond device
- *
- * 2001/5/17 - Tim Anderson <tsa at mvista.com>
- * - 2 paths for releasing for slave release; 1 through ioctl
- * and 2) through close. Both paths need to release the same way.
- * - the free slave in bond release is changing slave status before
- * the free. The netdev_set_master() is intended to change slave state
- * so it should not be done as part of the release process.
- * - Simple rule for slave state at release: only the active in A/B and
- * only one in the trunked case.
- *
- * 2001/6/01 - Tim Anderson <tsa at mvista.com>
- * - Now call dev_close when releasing a slave so it doesn't screw up
- * out routing table.
- *
- * 2001/6/01 - Chad N. Tindel <ctindel at ieee dot org>
- * - Added /proc support for getting bond and slave information.
- * Information is in /proc/net/<bond device>/info.
- * - Changed the locking when calling bond_close to prevent deadlock.
- *
- * 2001/8/05 - Janice Girouard <girouard at us.ibm.com>
- * - correct problem where refcnt of slave is not incremented in bond_ioctl
- * so the system hangs when halting.
- * - correct locking problem when unable to malloc in bond_enslave.
- * - adding bond_xmit_xor logic.
- * - adding multiple bond device support.
- *
- * 2001/8/13 - Erik Habbinga <erik_habbinga at hp dot com>
- * - correct locking problem with rtnl_exlock_nowait
- *
- * 2001/8/23 - Janice Girouard <girouard at us.ibm.com>
- * - bzero initial dev_bonds, to correct oops
- * - convert SIOCDEVPRIVATE to new MII ioctl calls
- *
- * 2001/9/13 - Takao Indoh <indou dot takao at jp dot fujitsu dot com>
- * - Add the BOND_CHANGE_ACTIVE ioctl implementation
- *
- * 2001/9/14 - Mark Huth <mhuth at mvista dot com>
- * - Change MII_LINK_READY to not check for end of auto-negotiation,
- * but only for an up link.
- *
- * 2001/9/20 - Chad N. Tindel <ctindel at ieee dot org>
- * - Add the device field to bonding_t. Previously the net_device
- * corresponding to a bond wasn't available from the bonding_t
- * structure.
- *
- * 2001/9/25 - Janice Girouard <girouard at us.ibm.com>
- * - add arp_monitor for active backup mode
- *
- * 2001/10/23 - Takao Indoh <indou dot takao at jp dot fujitsu dot com>
- * - Various memory leak fixes
- *
- * 2001/11/5 - Mark Huth <mark dot huth at mvista dot com>
- * - Don't take rtnl lock in bond_mii_monitor as it deadlocks under
- * certain hotswap conditions.
- * Note: this same change may be required in bond_arp_monitor ???
- * - Remove possibility of calling bond_sethwaddr with NULL slave_dev ptr
- * - Handle hot swap ethernet interface deregistration events to remove
- * kernel oops following hot swap of enslaved interface
- *
- * 2002/1/2 - Chad N. Tindel <ctindel at ieee dot org>
- * - Restore original slave flags at release time.
- *
- * 2002/02/18 - Erik Habbinga <erik_habbinga at hp dot com>
- * - bond_release(): calling kfree on our_slave after call to
- * bond_restore_slave_flags, not before
- * - bond_enslave(): saving slave flags into original_flags before
- * call to netdev_set_master, so the IFF_SLAVE flag doesn't end
- * up in original_flags
- *
- * 2002/04/05 - Mark Smith <mark.smith at comdev dot cc> and
- * Steve Mead <steve.mead at comdev dot cc>
- * - Port Gleb Natapov's multicast support patchs from 2.4.12
- * to 2.4.18 adding support for multicast.
- *
- * 2002/06/10 - Tony Cureington <tony.cureington * hp_com>
- * - corrected uninitialized pointer (ifr.ifr_data) in bond_check_dev_link;
- * actually changed function to use MIIPHY, then MIIREG, and finally
- * ETHTOOL to determine the link status
- * - fixed bad ifr_data pointer assignments in bond_ioctl
- * - corrected mode 1 being reported as active-backup in bond_get_info;
- * also added text to distinguish type of load balancing (rr or xor)
- * - change arp_ip_target module param from "1-12s" (array of 12 ptrs)
- * to "s" (a single ptr)
- *
- * 2002/08/30 - Jay Vosburgh <fubar at us dot ibm dot com>
- * - Removed acquisition of xmit_lock in set_multicast_list; caused
- * deadlock on SMP (lock is held by caller).
- * - Revamped SIOCGMIIPHY, SIOCGMIIREG portion of bond_check_dev_link().
- *
- * 2002/09/18 - Jay Vosburgh <fubar at us dot ibm dot com>
- * - Fixed up bond_check_dev_link() (and callers): removed some magic
- * numbers, banished local MII_ defines, wrapped ioctl calls to
- * prevent EFAULT errors
- *
- * 2002/9/30 - Jay Vosburgh <fubar at us dot ibm dot com>
- * - make sure the ip target matches the arp_target before saving the
- * hw address.
- *
- * 2002/9/30 - Dan Eisner <eisner at 2robots dot com>
- * - make sure my_ip is set before taking down the link, since
- * not all switches respond if the source ip is not set.
- *
- * 2002/10/8 - Janice Girouard <girouard at us dot ibm dot com>
- * - read in the local ip address when enslaving a device
- * - add primary support
- * - make sure 2*arp_interval has passed when a new device
- * is brought on-line before taking it down.
- *
- * 2002/09/11 - Philippe De Muyter <phdm at macqel dot be>
- * - Added bond_xmit_broadcast logic.
- * - Added bond_mode() support function.
- *
- * 2002/10/26 - Laurent Deniel <laurent.deniel at free.fr>
- * - allow to register multicast addresses only on active slave
- * (useful in active-backup mode)
- * - add multicast module parameter
- * - fix deletion of multicast groups after unloading module
- *
- * 2002/11/06 - Kameshwara Rayaprolu <kameshwara.rao * wipro_com>
- * - Changes to prevent panic from closing the device twice; if we close
- * the device in bond_release, we must set the original_flags to down
- * so it won't be closed again by the network layer.
- *
- * 2002/11/07 - Tony Cureington <tony.cureington * hp_com>
- * - Fix arp_target_hw_addr memory leak
- * - Created activebackup_arp_monitor function to handle arp monitoring
- * in active backup mode - the bond_arp_monitor had several problems...
- * such as allowing slaves to tx arps sequentially without any delay
- * for a response
- * - Renamed bond_arp_monitor to loadbalance_arp_monitor and re-wrote
- * this function to just handle arp monitoring in load-balancing mode;
- * it is a lot more compact now
- * - Changes to ensure one and only one slave transmits in active-backup
- * mode
- * - Robustesize parameters; warn users about bad combinations of
- * parameters; also if miimon is specified and a network driver does
- * not support MII or ETHTOOL, inform the user of this
- * - Changes to support link_failure_count when in arp monitoring mode
- * - Fix up/down delay reported in /proc
- * - Added version; log version; make version available from "modinfo -d"
- * - Fixed problem in bond_check_dev_link - if the first IOCTL (SIOCGMIIPH)
- * failed, the ETHTOOL ioctl never got a chance
- *
- * 2002/11/16 - Laurent Deniel <laurent.deniel at free.fr>
- * - fix multicast handling in activebackup_arp_monitor
- * - remove one unnecessary and confusing curr_active_slave == slave test
- * in activebackup_arp_monitor
- *
- * 2002/11/17 - Laurent Deniel <laurent.deniel at free.fr>
- * - fix bond_slave_info_query when slave_id = num_slaves
- *
- * 2002/11/19 - Janice Girouard <girouard at us dot ibm dot com>
- * - correct ifr_data reference. Update ifr_data reference
- * to mii_ioctl_data struct values to avoid confusion.
- *
- * 2002/11/22 - Bert Barbe <bert.barbe at oracle dot com>
- * - Add support for multiple arp_ip_target
- *
- * 2002/12/13 - Jay Vosburgh <fubar at us dot ibm dot com>
- * - Changed to allow text strings for mode and multicast, e.g.,
- * insmod bonding mode=active-backup. The numbers still work.
- * One change: an invalid choice will cause module load failure,
- * rather than the previous behavior of just picking one.
- * - Minor cleanups; got rid of dup ctype stuff, atoi function
- *
- * 2003/02/07 - Jay Vosburgh <fubar at us dot ibm dot com>
- * - Added use_carrier module parameter that causes miimon to
- * use netif_carrier_ok() test instead of MII/ETHTOOL ioctls.
- * - Minor cleanups; consolidated ioctl calls to one function.
- *
- * 2003/02/07 - Tony Cureington <tony.cureington * hp_com>
- * - Fix bond_mii_monitor() logic error that could result in
- * bonding round-robin mode ignoring links after failover/recovery
- *
- * 2003/03/17 - Jay Vosburgh <fubar at us dot ibm dot com>
- * - kmalloc fix (GFP_KERNEL to GFP_ATOMIC) reported by
- * Shmulik dot Hen at intel.com.
- * - Based on discussion on mailing list, changed use of
- * update_slave_cnt(), created wrapper functions for adding/removing
- * slaves, changed bond_xmit_xor() to check slave_cnt instead of
- * checking slave and slave->dev (which only worked by accident).
- * - Misc code cleanup: get arp_send() prototype from header file,
- * add max_bonds to bonding.txt.
- *
- * 2003/03/18 - Tsippy Mendelson <tsippy.mendelson at intel dot com> and
- * Shmulik Hen <shmulik.hen at intel dot com>
- * - Make sure only bond_attach_slave() and bond_detach_slave() can
- * manipulate the slave list, including slave_cnt, even when in
- * bond_release_all().
- * - Fixed hang in bond_release() with traffic running:
- * netdev_set_master() must not be called from within the bond lock.
- *
- * 2003/03/18 - Tsippy Mendelson <tsippy.mendelson at intel dot com> and
- * Shmulik Hen <shmulik.hen at intel dot com>
- * - Fixed hang in bond_enslave() with traffic running:
- * netdev_set_master() must not be called from within the bond lock.
- *
- * 2003/03/18 - Amir Noam <amir.noam at intel dot com>
- * - Added support for getting slave's speed and duplex via ethtool.
- * Needed for 802.3ad and other future modes.
- *
- * 2003/03/18 - Tsippy Mendelson <tsippy.mendelson at intel dot com> and
- * Shmulik Hen <shmulik.hen at intel dot com>
- * - Enable support of modes that need to use the unique mac address of
- * each slave.
- * * bond_enslave(): Moved setting the slave's mac address, and
- * openning it, from the application to the driver. This breaks
- * backward comaptibility with old versions of ifenslave that open
- * the slave before enalsving it !!!.
- * * bond_release(): The driver also takes care of closing the slave
- * and restoring its original mac address.
- * - Removed the code that restores all base driver's flags.
- * Flags are automatically restored once all undo stages are done
- * properly.
- * - Block possibility of enslaving before the master is up. This
- * prevents putting the system in an unstable state.
- *
- * 2003/03/18 - Amir Noam <amir.noam at intel dot com>,
- * Tsippy Mendelson <tsippy.mendelson at intel dot com> and
- * Shmulik Hen <shmulik.hen at intel dot com>
- * - Added support for IEEE 802.3ad Dynamic link aggregation mode.
- *
- * 2003/05/01 - Amir Noam <amir.noam at intel dot com>
- * - Added ABI version control to restore compatibility between
- * new/old ifenslave and new/old bonding.
- *
- * 2003/05/01 - Shmulik Hen <shmulik.hen at intel dot com>
- * - Fixed bug in bond_release_all(): save old value of curr_active_slave
- * before setting it to NULL.
- * - Changed driver versioning scheme to include version number instead
- * of release date (that is already in another field). There are 3
- * fields X.Y.Z where:
- * X - Major version - big behavior changes
- * Y - Minor version - addition of features
- * Z - Extra version - minor changes and bug fixes
- * The current version is 1.0.0 as a base line.
- *
- * 2003/05/01 - Tsippy Mendelson <tsippy.mendelson at intel dot com> and
- * Amir Noam <amir.noam at intel dot com>
- * - Added support for lacp_rate module param.
- * - Code beautification and style changes (mainly in comments).
- * new version - 1.0.1
- *
- * 2003/05/01 - Shmulik Hen <shmulik.hen at intel dot com>
- * - Based on discussion on mailing list, changed locking scheme
- * to use lock/unlock or lock_bh/unlock_bh appropriately instead
- * of lock_irqsave/unlock_irqrestore. The new scheme helps exposing
- * hidden bugs and solves system hangs that occurred due to the fact
- * that holding lock_irqsave doesn't prevent softirqs from running.
- * This also increases total throughput since interrupts are not
- * blocked on each transmitted packets or monitor timeout.
- * new version - 2.0.0
- *
- * 2003/05/01 - Shmulik Hen <shmulik.hen at intel dot com>
- * - Added support for Transmit load balancing mode.
- * - Concentrate all assignments of curr_active_slave to a single point
- * so specific modes can take actions when the primary adapter is
- * changed.
- * - Take the updelay parameter into consideration during bond_enslave
- * since some adapters loose their link during setting the device.
- * - Renamed bond_3ad_link_status_changed() to
- * bond_3ad_handle_link_change() for compatibility with TLB.
- * new version - 2.1.0
- *
- * 2003/05/01 - Tsippy Mendelson <tsippy.mendelson at intel dot com>
- * - Added support for Adaptive load balancing mode which is
- * equivalent to Transmit load balancing + Receive load balancing.
- * new version - 2.2.0
- *
- * 2003/05/15 - Jay Vosburgh <fubar at us dot ibm dot com>
- * - Applied fix to activebackup_arp_monitor posted to bonding-devel
- * by Tony Cureington <tony.cureington * hp_com>. Fixes ARP
- * monitor endless failover bug. Version to 2.2.10
- *
- * 2003/05/20 - Amir Noam <amir.noam at intel dot com>
- * - Fixed bug in ABI version control - Don't commit to a specific
- * ABI version if receiving unsupported ioctl commands.
- *
- * 2003/05/22 - Jay Vosburgh <fubar at us dot ibm dot com>
- * - Fix ifenslave -c causing bond to loose existing routes;
- * added bond_set_mac_address() that doesn't require the
- * bond to be down.
- * - In conjunction with fix for ifenslave -c, in
- * bond_change_active(), changing to the already active slave
- * is no longer an error (it successfully does nothing).
- *
- * 2003/06/30 - Amir Noam <amir.noam at intel dot com>
- * - Fixed bond_change_active() for ALB/TLB modes.
- * Version to 2.2.14.
- *
- * 2003/07/29 - Amir Noam <amir.noam at intel dot com>
- * - Fixed ARP monitoring bug.
- * Version to 2.2.15.
- *
- * 2003/07/31 - Willy Tarreau <willy at ods dot org>
- * - Fixed kernel panic when using ARP monitoring without
- * setting bond's IP address.
- * Version to 2.2.16.
- *
- * 2003/08/06 - Amir Noam <amir.noam at intel dot com>
- * - Back port from 2.6: use alloc_netdev(); fix /proc handling;
- * made stats a part of bond struct so no need to allocate
- * and free it separately; use standard list operations instead
- * of pre-allocated array of bonds.
- * Version to 2.3.0.
- *
- * 2003/08/07 - Jay Vosburgh <fubar at us dot ibm dot com>,
- * Amir Noam <amir.noam at intel dot com> and
- * Shmulik Hen <shmulik.hen at intel dot com>
- * - Propagating master's settings: Distinguish between modes that
- * use a primary slave from those that don't, and propagate settings
- * accordingly; Consolidate change_active opeartions and add
- * reselect_active and find_best opeartions; Decouple promiscuous
- * handling from the multicast mode setting; Add support for changing
- * HW address and MTU with proper unwind; Consolidate procfs code,
- * add CHANGENAME handler; Enhance netdev notification handling.
- * Version to 2.4.0.
- *
- * 2003/09/15 - Stephen Hemminger <shemminger at osdl dot org>,
- * Amir Noam <amir.noam at intel dot com>
- * - Convert /proc to seq_file interface.
- * Change /proc/net/bondX/info to /proc/net/bonding/bondX.
- * Set version to 2.4.1.
- *
- * 2003/11/20 - Amir Noam <amir.noam at intel dot com>
- * - Fix /proc creation/destruction.
- *
- * 2003/12/01 - Shmulik Hen <shmulik.hen at intel dot com>
- * - Massive cleanup - Set version to 2.5.0
- * Code changes:
- * o Consolidate format of prints and debug prints.
- * o Remove bonding_t/slave_t typedefs and consolidate all casts.
- * o Remove dead code and unnecessary checks.
- * o Consolidate starting/stopping timers.
- * o Consolidate handling of primary module param throughout the code.
- * o Removed multicast module param support - all settings are done
- * according to mode.
- * o Slave list iteration - bond is no longer part of the list,
- * added cyclic list iteration macros.
- * o Consolidate error handling in all xmit functions.
- * Style changes:
- * o Consolidate function naming and declarations.
- * o Consolidate function params and local variables names.
- * o Consolidate return values.
- * o Consolidate curly braces.
- * o Consolidate conditionals format.
- * o Change struct member names and types.
- * o Chomp trailing spaces, remove empty lines, fix indentations.
- * o Re-organize code according to context.
- *
- * 2003/12/30 - Amir Noam <amir.noam at intel dot com>
- * - Fixed: Cannot remove and re-enslave the original active slave.
- * - Fixed: Releasing the original active slave causes mac address
- * duplication.
- * - Add support for slaves that use ethtool_ops.
- * Set version to 2.5.3.
- *
- * 2004/01/05 - Amir Noam <amir.noam at intel dot com>
- * - Save bonding parameters per bond instead of using the global values.
- * Set version to 2.5.4.
- *
- * 2004/01/14 - Shmulik Hen <shmulik.hen at intel dot com>
- * - Enhance VLAN support:
- * * Add support for VLAN hardware acceleration capable slaves.
- * * Add capability to tag self generated packets in ALB/TLB modes.
- * Set version to 2.6.0.
- * 2004/10/29 - Mitch Williams <mitch.a.williams at intel dot com>
- * - Fixed bug when unloading module while using 802.3ad. If
- * spinlock debugging is turned on, this causes a stack dump.
- * Solution is to move call to dev_remove_pack outside of the
- * spinlock.
- * Set version to 2.6.1.
- *
*/
//#define BONDING_DEBUG 1
-#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/sched.h>
#include <linux/ptrace.h>
#include <linux/ioport.h>
#include <linux/in.h>
+#include <net/ip.h>
#include <linux/ip.h>
+#include <linux/tcp.h>
+#include <linux/udp.h>
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/init.h>
#include <linux/ethtool.h>
#include <linux/if_vlan.h>
#include <linux/if_bonding.h>
+#include <net/route.h>
#include "bonding.h"
#include "bond_3ad.h"
#include "bond_alb.h"
static char *mode = NULL;
static char *primary = NULL;
static char *lacp_rate = NULL;
+static char *xmit_hash_policy = NULL;
static int arp_interval = BOND_LINK_ARP_INTERV;
static char *arp_ip_target[BOND_MAX_ARP_TARGETS] = { NULL, };
+struct bond_params bonding_defaults;
module_param(max_bonds, int, 0);
MODULE_PARM_DESC(max_bonds, "Max number of bonded devices");
module_param(updelay, int, 0);
MODULE_PARM_DESC(updelay, "Delay before considering link up, in milliseconds");
module_param(downdelay, int, 0);
-MODULE_PARM_DESC(downdelay, "Delay before considering link down, in milliseconds");
+MODULE_PARM_DESC(downdelay, "Delay before considering link down, "
+ "in milliseconds");
module_param(use_carrier, int, 0);
-MODULE_PARM_DESC(use_carrier, "Use netif_carrier_ok (vs MII ioctls) in miimon; 0 for off, 1 for on (default)");
+MODULE_PARM_DESC(use_carrier, "Use netif_carrier_ok (vs MII ioctls) in miimon; "
+ "0 for off, 1 for on (default)");
module_param(mode, charp, 0);
-MODULE_PARM_DESC(mode, "Mode of operation : 0 for round robin, 1 for active-backup, 2 for xor");
+MODULE_PARM_DESC(mode, "Mode of operation : 0 for balance-rr, "
+ "1 for active-backup, 2 for balance-xor, "
+ "3 for broadcast, 4 for 802.3ad, 5 for balance-tlb, "
+ "6 for balance-alb");
module_param(primary, charp, 0);
MODULE_PARM_DESC(primary, "Primary network device to use");
module_param(lacp_rate, charp, 0);
-MODULE_PARM_DESC(lacp_rate, "LACPDU tx rate to request from 802.3ad partner (slow/fast)");
+MODULE_PARM_DESC(lacp_rate, "LACPDU tx rate to request from 802.3ad partner "
+ "(slow/fast)");
+module_param(xmit_hash_policy, charp, 0);
+MODULE_PARM_DESC(xmit_hash_policy, "XOR hashing method: 0 for layer 2 (default)"
+ ", 1 for layer 3+4");
module_param(arp_interval, int, 0);
MODULE_PARM_DESC(arp_interval, "arp interval in milliseconds");
module_param_array(arp_ip_target, charp, NULL, 0);
/*----------------------------- Global variables ----------------------------*/
-static const char *version =
+static const char * const version =
DRV_DESCRIPTION ": v" DRV_VERSION " (" DRV_RELDATE ")\n";
-static LIST_HEAD(bond_dev_list);
+LIST_HEAD(bond_dev_list);
#ifdef CONFIG_PROC_FS
static struct proc_dir_entry *bond_proc_dir = NULL;
#endif
+extern struct rw_semaphore bonding_rwsem;
static u32 arp_target[BOND_MAX_ARP_TARGETS] = { 0, } ;
static int arp_ip_count = 0;
-static u32 my_ip = 0;
static int bond_mode = BOND_MODE_ROUNDROBIN;
+static int xmit_hashtype= BOND_XMIT_POLICY_LAYER2;
static int lacp_fast = 0;
-static int app_abi_ver = 0;
-static int orig_app_abi_ver = -1; /* This is used to save the first ABI version
- * we receive from the application. Once set,
- * it won't be changed, and the module will
- * refuse to enslave/release interfaces if the
- * command comes from an application using
- * another ABI version.
- */
-
-struct bond_parm_tbl {
- char *modename;
- int mode;
-};
-static struct bond_parm_tbl bond_lacp_tbl[] = {
+
+struct bond_parm_tbl bond_lacp_tbl[] = {
{ "slow", AD_LACP_SLOW},
{ "fast", AD_LACP_FAST},
{ NULL, -1},
};
-static struct bond_parm_tbl bond_mode_tbl[] = {
+struct bond_parm_tbl bond_mode_tbl[] = {
{ "balance-rr", BOND_MODE_ROUNDROBIN},
{ "active-backup", BOND_MODE_ACTIVEBACKUP},
{ "balance-xor", BOND_MODE_XOR},
{ NULL, -1},
};
+struct bond_parm_tbl xmit_hashtype_tbl[] = {
+{ "layer2", BOND_XMIT_POLICY_LAYER2},
+{ "layer3+4", BOND_XMIT_POLICY_LAYER34},
+{ NULL, -1},
+};
+
/*-------------------------- Forward declarations ---------------------------*/
-static inline void bond_set_mode_ops(struct net_device *bond_dev, int mode);
+static void bond_send_gratuitous_arp(struct bonding *bond);
/*---------------------------- General routines -----------------------------*/
-static const char *bond_mode_name(int mode)
+const char *bond_mode_name(int mode)
{
switch (mode) {
case BOND_MODE_ROUNDROBIN :
INIT_LIST_HEAD(&vlan->vlan_list);
vlan->vlan_id = vlan_id;
+ vlan->vlan_ip = 0;
write_lock_bh(&bond->lock);
res = bond_add_vlan(bond, vid);
if (res) {
printk(KERN_ERR DRV_NAME
- ": %s: Failed to add vlan id %d\n",
+ ": %s: Error: Failed to add vlan id %d\n",
bond_dev->name, vid);
}
}
res = bond_del_vlan(bond, vid);
if (res) {
printk(KERN_ERR DRV_NAME
- ": %s: Failed to remove vlan id %d\n",
+ ": %s: Error: Failed to remove vlan id %d\n",
bond_dev->name, vid);
}
}
/*------------------------------- Link status -------------------------------*/
+/*
+ * Set the carrier state for the master according to the state of its
+ * slaves. If any slaves are up, the master is up. In 802.3ad mode,
+ * do special 802.3ad magic.
+ *
+ * Returns zero if carrier state does not change, nonzero if it does.
+ */
+static int bond_set_carrier(struct bonding *bond)
+{
+ struct slave *slave;
+ int i;
+
+ if (bond->slave_cnt == 0)
+ goto down;
+
+ if (bond->params.mode == BOND_MODE_8023AD)
+ return bond_3ad_set_carrier(bond);
+
+ bond_for_each_slave(bond, slave, i) {
+ if (slave->link == BOND_LINK_UP) {
+ if (!netif_carrier_ok(bond->dev)) {
+ netif_carrier_on(bond->dev);
+ return 1;
+ }
+ return 0;
+ }
+ }
+
+down:
+ if (netif_carrier_ok(bond->dev)) {
+ netif_carrier_off(bond->dev);
+ return 1;
+ }
+ return 0;
+}
+
/*
* Get link speed and duplex from the slave's base driver
* using ethtool. If for some reason the call fails or the
slave->duplex = DUPLEX_FULL;
if (slave_dev->ethtool_ops) {
- u32 res;
+ int res;
if (!slave_dev->ethtool_ops->get_settings) {
return -1;
/*
* Copy all the Multicast addresses from src to the bonding device dst
*/
-static int bond_mc_list_copy(struct dev_mc_list *mc_list, struct bonding *bond, int gpf_flag)
+static int bond_mc_list_copy(struct dev_mc_list *mc_list, struct bonding *bond,
+ gfp_t gfp_flag)
{
struct dev_mc_list *dmi, *new_dmi;
for (dmi = mc_list; dmi; dmi = dmi->next) {
- new_dmi = kmalloc(sizeof(struct dev_mc_list), gpf_flag);
+ new_dmi = kmalloc(sizeof(struct dev_mc_list), gfp_flag);
if (!new_dmi) {
/* FIXME: Potential memory leak !!! */
*
* Warning: Caller must hold curr_slave_lock for writing.
*/
-static void bond_change_active_slave(struct bonding *bond, struct slave *new_active)
+void bond_change_active_slave(struct bonding *bond, struct slave *new_active)
{
struct slave *old_active = bond->curr_active_slave;
}
}
- if (bond->params.mode == BOND_MODE_ACTIVEBACKUP) {
- if (old_active) {
- bond_set_slave_inactive_flags(old_active);
- }
-
- if (new_active) {
- bond_set_slave_active_flags(new_active);
- }
- }
-
if (USES_PRIMARY(bond->params.mode)) {
bond_mc_swap(bond, new_active, old_active);
}
if ((bond->params.mode == BOND_MODE_TLB) ||
(bond->params.mode == BOND_MODE_ALB)) {
bond_alb_handle_active_change(bond, new_active);
+ if (old_active)
+ bond_set_slave_inactive_flags(old_active);
+ if (new_active)
+ bond_set_slave_active_flags(new_active);
} else {
bond->curr_active_slave = new_active;
}
+
+ if (bond->params.mode == BOND_MODE_ACTIVEBACKUP) {
+ if (old_active) {
+ bond_set_slave_inactive_flags(old_active);
+ }
+
+ if (new_active) {
+ bond_set_slave_active_flags(new_active);
+ }
+ bond_send_gratuitous_arp(bond);
+ }
}
/**
*
* Warning: Caller must hold curr_slave_lock for writing.
*/
-static void bond_select_active_slave(struct bonding *bond)
+void bond_select_active_slave(struct bonding *bond)
{
struct slave *best_slave;
+ int rv;
best_slave = bond_find_best_slave(bond);
if (best_slave != bond->curr_active_slave) {
bond_change_active_slave(bond, best_slave);
+ rv = bond_set_carrier(bond);
+ if (!rv)
+ return;
+
+ if (netif_carrier_ok(bond->dev)) {
+ printk(KERN_INFO DRV_NAME
+ ": %s: first active interface up!\n",
+ bond->dev->name);
+ } else {
+ printk(KERN_INFO DRV_NAME ": %s: "
+ "now running without any active interface !\n",
+ bond->dev->name);
+ }
}
}
/*---------------------------------- IOCTL ----------------------------------*/
-static int bond_sethwaddr(struct net_device *bond_dev, struct net_device *slave_dev)
+int bond_sethwaddr(struct net_device *bond_dev, struct net_device *slave_dev)
{
dprintk("bond_dev=%p\n", bond_dev);
dprintk("slave_dev=%p\n", slave_dev);
return 0;
}
+#define BOND_INTERSECT_FEATURES \
+ (NETIF_F_SG | NETIF_F_ALL_CSUM | NETIF_F_TSO | NETIF_F_UFO)
+
+/*
+ * Compute the common dev->feature set available to all slaves. Some
+ * feature bits are managed elsewhere, so preserve feature bits set on
+ * master device that are not part of the examined set.
+ */
+static int bond_compute_features(struct bonding *bond)
+{
+ unsigned long features = BOND_INTERSECT_FEATURES;
+ struct slave *slave;
+ struct net_device *bond_dev = bond->dev;
+ int i;
+
+ bond_for_each_slave(bond, slave, i)
+ features &= (slave->dev->features & BOND_INTERSECT_FEATURES);
+
+ if ((features & NETIF_F_SG) &&
+ !(features & NETIF_F_ALL_CSUM))
+ features &= ~NETIF_F_SG;
+
+ /*
+ * features will include NETIF_F_TSO (NETIF_F_UFO) iff all
+ * slave devices support NETIF_F_TSO (NETIF_F_UFO), which
+ * implies that all slaves also support scatter-gather
+ * (NETIF_F_SG), which implies that features also includes
+ * NETIF_F_SG. So no need to check whether we have an
+ * illegal combination of NETIF_F_{TSO,UFO} and
+ * !NETIF_F_SG
+ */
+
+ features |= (bond_dev->features & ~BOND_INTERSECT_FEATURES);
+ bond_dev->features = features;
+
+ return 0;
+}
+
/* enslave device <slave> to bond device <master> */
-static int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev)
+int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev)
{
struct bonding *bond = bond_dev->priv;
struct slave *new_slave = NULL;
int old_features = bond_dev->features;
int res = 0;
- if (slave_dev->do_ioctl == NULL) {
+ if (!bond->params.use_carrier && slave_dev->ethtool_ops == NULL &&
+ slave_dev->do_ioctl == NULL) {
printk(KERN_WARNING DRV_NAME
- ": Warning : no link monitoring support for %s\n",
- slave_dev->name);
+ ": %s: Warning: no link monitoring support for %s\n",
+ bond_dev->name, slave_dev->name);
}
/* bond must be initialized by bond_open() before enslaving */
dprintk("%s: NETIF_F_VLAN_CHALLENGED\n", slave_dev->name);
if (!list_empty(&bond->vlan_list)) {
printk(KERN_ERR DRV_NAME
- ": Error: cannot enslave VLAN "
+ ": %s: Error: cannot enslave VLAN "
"challenged slave %s on VLAN enabled "
- "bond %s\n", slave_dev->name,
+ "bond %s\n", bond_dev->name, slave_dev->name,
bond_dev->name);
return -EPERM;
} else {
printk(KERN_WARNING DRV_NAME
- ": Warning: enslaved VLAN challenged "
+ ": %s: Warning: enslaved VLAN challenged "
"slave %s. Adding VLANs will be blocked as "
"long as %s is part of bond %s\n",
- slave_dev->name, slave_dev->name,
+ bond_dev->name, slave_dev->name, slave_dev->name,
bond_dev->name);
bond_dev->features |= NETIF_F_VLAN_CHALLENGED;
}
}
}
- if (app_abi_ver >= 1) {
- /* The application is using an ABI, which requires the
- * slave interface to be closed.
- */
- if ((slave_dev->flags & IFF_UP)) {
- printk(KERN_ERR DRV_NAME
- ": Error: %s is up\n",
- slave_dev->name);
- res = -EPERM;
- goto err_undo_flags;
- }
-
- if (slave_dev->set_mac_address == NULL) {
- printk(KERN_ERR DRV_NAME
- ": Error: The slave device you specified does "
- "not support setting the MAC address.\n");
- printk(KERN_ERR
- "Your kernel likely does not support slave "
- "devices.\n");
-
- res = -EOPNOTSUPP;
- goto err_undo_flags;
- }
- } else {
- /* The application is not using an ABI, which requires the
- * slave interface to be open.
- */
- if (!(slave_dev->flags & IFF_UP)) {
- printk(KERN_ERR DRV_NAME
- ": Error: %s is not running\n",
- slave_dev->name);
- res = -EINVAL;
- goto err_undo_flags;
- }
+ /*
+ * Old ifenslave binaries are no longer supported. These can
+ * be identified with moderate accurary by the state of the slave:
+ * the current ifenslave will set the interface down prior to
+ * enslaving it; the old ifenslave will not.
+ */
+ if ((slave_dev->flags & IFF_UP)) {
+ printk(KERN_ERR DRV_NAME ": %s is up. "
+ "This may be due to an out of date ifenslave.\n",
+ slave_dev->name);
+ res = -EPERM;
+ goto err_undo_flags;
+ }
- if ((bond->params.mode == BOND_MODE_8023AD) ||
- (bond->params.mode == BOND_MODE_TLB) ||
- (bond->params.mode == BOND_MODE_ALB)) {
- printk(KERN_ERR DRV_NAME
- ": Error: to use %s mode, you must upgrade "
- "ifenslave.\n",
- bond_mode_name(bond->params.mode));
- res = -EOPNOTSUPP;
- goto err_undo_flags;
- }
+ if (slave_dev->set_mac_address == NULL) {
+ printk(KERN_ERR DRV_NAME
+ ": %s: Error: The slave device you specified does "
+ "not support setting the MAC address. "
+ "Your kernel likely does not support slave "
+ "devices.\n", bond_dev->name);
+ res = -EOPNOTSUPP;
+ goto err_undo_flags;
}
new_slave = kmalloc(sizeof(struct slave), GFP_KERNEL);
*/
new_slave->original_flags = slave_dev->flags;
- if (app_abi_ver >= 1) {
- /* save slave's original ("permanent") mac address for
- * modes that needs it, and for restoring it upon release,
- * and then set it to the master's address
- */
- memcpy(new_slave->perm_hwaddr, slave_dev->dev_addr, ETH_ALEN);
+ /*
+ * Save slave's original ("permanent") mac address for modes
+ * that need it, and for restoring it upon release, and then
+ * set it to the master's address
+ */
+ memcpy(new_slave->perm_hwaddr, slave_dev->dev_addr, ETH_ALEN);
- /* set slave to master's mac address
- * The application already set the master's
- * mac address to that of the first slave
- */
- memcpy(addr.sa_data, bond_dev->dev_addr, bond_dev->addr_len);
- addr.sa_family = slave_dev->type;
- res = dev_set_mac_address(slave_dev, &addr);
- if (res) {
- dprintk("Error %d calling set_mac_address\n", res);
- goto err_free;
- }
+ /*
+ * Set slave to master's mac address. The application already
+ * set the master's mac address to that of the first slave
+ */
+ memcpy(addr.sa_data, bond_dev->dev_addr, bond_dev->addr_len);
+ addr.sa_family = slave_dev->type;
+ res = dev_set_mac_address(slave_dev, &addr);
+ if (res) {
+ dprintk("Error %d calling set_mac_address\n", res);
+ goto err_free;
+ }
- /* open the slave since the application closed it */
- res = dev_open(slave_dev);
- if (res) {
- dprintk("Openning slave %s failed\n", slave_dev->name);
- goto err_restore_mac;
- }
+ /* open the slave since the application closed it */
+ res = dev_open(slave_dev);
+ if (res) {
+ dprintk("Openning slave %s failed\n", slave_dev->name);
+ goto err_restore_mac;
}
res = netdev_set_master(slave_dev, bond_dev);
if (res) {
dprintk("Error %d calling netdev_set_master\n", res);
- if (app_abi_ver < 1) {
- goto err_free;
- } else {
- goto err_close;
- }
+ goto err_close;
}
new_slave->dev = slave_dev;
new_slave->delay = 0;
new_slave->link_failure_count = 0;
+ bond_compute_features(bond);
+
if (bond->params.miimon && !bond->params.use_carrier) {
link_reporting = bond_check_dev_link(bond, slave_dev, 1);
* the messages for netif_carrier.
*/
printk(KERN_WARNING DRV_NAME
- ": Warning: MII and ETHTOOL support not "
+ ": %s: Warning: MII and ETHTOOL support not "
"available for interface %s, and "
"arp_interval/arp_ip_target module parameters "
"not specified, thus bonding will not detect "
"link failures! see bonding.txt for details.\n",
- slave_dev->name);
+ bond_dev->name, slave_dev->name);
} else if (link_reporting == -1) {
/* unable get link status using mii/ethtool */
printk(KERN_WARNING DRV_NAME
- ": Warning: can't get link status from "
+ ": %s: Warning: can't get link status from "
"interface %s; the network driver associated "
"with this interface does not support MII or "
"ETHTOOL link status reporting, thus miimon "
"has no effect on this interface.\n",
- slave_dev->name);
+ bond_dev->name, slave_dev->name);
}
}
if (bond_update_speed_duplex(new_slave) &&
(new_slave->link != BOND_LINK_DOWN)) {
printk(KERN_WARNING DRV_NAME
- ": Warning: failed to get speed and duplex from %s, "
+ ": %s: Warning: failed to get speed and duplex from %s, "
"assumed to be 100Mb/sec and Full.\n",
- new_slave->dev->name);
+ bond_dev->name, new_slave->dev->name);
if (bond->params.mode == BOND_MODE_8023AD) {
- printk(KERN_WARNING
- "Operation of 802.3ad mode requires ETHTOOL "
+ printk(KERN_WARNING DRV_NAME
+ ": %s: Warning: Operation of 802.3ad mode requires ETHTOOL "
"support in base driver for proper aggregator "
- "selection.\n");
+ "selection.\n", bond_dev->name);
}
}
switch (bond->params.mode) {
case BOND_MODE_ACTIVEBACKUP:
- /* if we're in active-backup mode, we need one and only one active
- * interface. The backup interfaces will have their NOARP flag set
- * because we need them to be completely deaf and not to respond to
- * any ARP request on the network to avoid fooling a switch. Thus,
- * since we guarantee that curr_active_slave always point to the last
- * usable interface, we just have to verify this interface's flag.
+ /* if we're in active-backup mode, we need one and
+ * only one active interface. The backup interfaces
+ * will have their SLAVE_INACTIVE flag set because we
+ * need them to be drop all packets. Thus, since we
+ * guarantee that curr_active_slave always point to
+ * the last usable interface, we just have to verify
+ * this interface's flag.
*/
if (((!bond->curr_active_slave) ||
- (bond->curr_active_slave->dev->flags & IFF_NOARP)) &&
+ (bond->curr_active_slave->dev->priv_flags & IFF_SLAVE_INACTIVE)) &&
(new_slave->link != BOND_LINK_DOWN)) {
- dprintk("This is the first active slave\n");
/* first slave or no active slave yet, and this link
is OK, so make this interface the active one */
bond_change_active_slave(bond, new_slave);
+ printk(KERN_INFO DRV_NAME
+ ": %s: first active interface up!\n",
+ bond->dev->name);
+ netif_carrier_on(bond->dev);
+
} else {
dprintk("This is just a backup slave\n");
bond_set_slave_inactive_flags(new_slave);
* is OK, so make this interface the active one
*/
bond_change_active_slave(bond, new_slave);
+ } else {
+ bond_set_slave_inactive_flags(new_slave);
}
break;
default:
break;
} /* switch(bond_mode) */
- write_unlock_bh(&bond->lock);
+ bond_set_carrier(bond);
- if (app_abi_ver < 1) {
- /*
- * !!! This is to support old versions of ifenslave.
- * We can remove this in 2.5 because our ifenslave takes
- * care of this for us.
- * We check to see if the master has a mac address yet.
- * If not, we'll give it the mac address of our slave device.
- */
- int ndx = 0;
-
- for (ndx = 0; ndx < bond_dev->addr_len; ndx++) {
- dprintk("Checking ndx=%d of bond_dev->dev_addr\n",
- ndx);
- if (bond_dev->dev_addr[ndx] != 0) {
- dprintk("Found non-zero byte at ndx=%d\n",
- ndx);
- break;
- }
- }
+ write_unlock_bh(&bond->lock);
- if (ndx == bond_dev->addr_len) {
- /*
- * We got all the way through the address and it was
- * all 0's.
- */
- dprintk("%s doesn't have a MAC address yet. \n",
- bond_dev->name);
- dprintk("Going to give assign it from %s.\n",
- slave_dev->name);
- bond_sethwaddr(bond_dev, slave_dev);
- }
- }
+ res = bond_create_slave_symlinks(bond_dev, slave_dev);
+ if (res)
+ goto err_unset_master;
printk(KERN_INFO DRV_NAME
": %s: enslaving %s as a%s interface with a%s link.\n",
err_undo_flags:
bond_dev->features = old_features;
-
+
return res;
}
* for Bonded connections:
* The first up interface should be left on and all others downed.
*/
-static int bond_release(struct net_device *bond_dev, struct net_device *slave_dev)
+int bond_release(struct net_device *bond_dev, struct net_device *slave_dev)
{
struct bonding *bond = bond_dev->priv;
struct slave *slave, *oldcurrent;
if (!(slave_dev->flags & IFF_SLAVE) ||
(slave_dev->master != bond_dev)) {
printk(KERN_ERR DRV_NAME
- ": Error: %s: cannot release %s.\n",
+ ": %s: Error: cannot release %s.\n",
bond_dev->name, slave_dev->name);
return -EINVAL;
}
printk(KERN_INFO DRV_NAME
": %s: %s not enslaved\n",
bond_dev->name, slave_dev->name);
+ write_unlock_bh(&bond->lock);
return -EINVAL;
}
ETH_ALEN);
if (!mac_addr_differ && (bond->slave_cnt > 1)) {
printk(KERN_WARNING DRV_NAME
- ": Warning: the permanent HWaddr of %s "
+ ": %s: Warning: the permanent HWaddr of %s "
"- %02X:%02X:%02X:%02X:%02X:%02X - is "
"still in use by %s. Set the HWaddr of "
"%s to a different address to avoid "
"conflicts.\n",
+ bond_dev->name,
slave_dev->name,
slave->perm_hwaddr[0],
slave->perm_hwaddr[1],
/* release the slave from its bond */
bond_detach_slave(bond, slave);
+ bond_compute_features(bond);
+
if (bond->primary_slave == slave) {
bond->primary_slave = NULL;
}
bond_alb_deinit_slave(bond, slave);
}
- if (oldcurrent == slave) {
+ if (oldcurrent == slave)
bond_select_active_slave(bond);
- if (!bond->curr_active_slave) {
- printk(KERN_INFO DRV_NAME
- ": %s: now running without any active "
- "interface !\n",
- bond_dev->name);
- }
- }
-
if (bond->slave_cnt == 0) {
+ bond_set_carrier(bond);
+
/* if the last slave was removed, zero the mac address
* of the master so it will be set by the application
* to the mac address of the first slave
bond_dev->features |= NETIF_F_VLAN_CHALLENGED;
} else {
printk(KERN_WARNING DRV_NAME
- ": Warning: clearing HW address of %s while it "
+ ": %s: Warning: clearing HW address of %s while it "
"still has VLANs.\n",
- bond_dev->name);
+ bond_dev->name, bond_dev->name);
printk(KERN_WARNING DRV_NAME
- ": When re-adding slaves, make sure the bond's "
- "HW address matches its VLANs'.\n");
+ ": %s: When re-adding slaves, make sure the bond's "
+ "HW address matches its VLANs'.\n",
+ bond_dev->name);
}
} else if ((bond_dev->features & NETIF_F_VLAN_CHALLENGED) &&
!bond_has_challenged_slaves(bond)) {
printk(KERN_INFO DRV_NAME
- ": last VLAN challenged slave %s "
+ ": %s: last VLAN challenged slave %s "
"left bond %s. VLAN blocking is removed\n",
- slave_dev->name, bond_dev->name);
+ bond_dev->name, slave_dev->name, bond_dev->name);
bond_dev->features &= ~NETIF_F_VLAN_CHALLENGED;
}
write_unlock_bh(&bond->lock);
+ /* must do this from outside any spinlocks */
+ bond_destroy_slave_symlinks(bond_dev, slave_dev);
+
bond_del_vlans_from_slave(bond, slave_dev);
/* If the mode USES_PRIMARY, then we should only remove its
/* close slave before restoring its mac address */
dev_close(slave_dev);
- if (app_abi_ver >= 1) {
- /* restore original ("permanent") mac address */
- memcpy(addr.sa_data, slave->perm_hwaddr, ETH_ALEN);
- addr.sa_family = slave_dev->type;
- dev_set_mac_address(slave_dev, &addr);
- }
+ /* restore original ("permanent") mac address */
+ memcpy(addr.sa_data, slave->perm_hwaddr, ETH_ALEN);
+ addr.sa_family = slave_dev->type;
+ dev_set_mac_address(slave_dev, &addr);
- /* restore the original state of the
- * IFF_NOARP flag that might have been
- * set by bond_set_slave_inactive_flags()
- */
- if ((slave->original_flags & IFF_NOARP) == 0) {
- slave_dev->flags &= ~IFF_NOARP;
- }
+ slave_dev->priv_flags &= ~(IFF_MASTER_8023AD | IFF_MASTER_ALB |
+ IFF_SLAVE_INACTIVE);
kfree(slave);
write_lock_bh(&bond->lock);
+ netif_carrier_off(bond_dev);
+
if (bond->slave_cnt == 0) {
goto out;
}
bond_alb_deinit_slave(bond, slave);
}
+ bond_compute_features(bond);
+
/* now that the slave is detached, unlock and perform
* all the undo steps that should not be called from
* within a lock.
*/
write_unlock_bh(&bond->lock);
+ bond_destroy_slave_symlinks(bond_dev, slave_dev);
bond_del_vlans_from_slave(bond, slave_dev);
/* If the mode USES_PRIMARY, then we should only remove its
/* close slave before restoring its mac address */
dev_close(slave_dev);
- if (app_abi_ver >= 1) {
- /* restore original ("permanent") mac address*/
- memcpy(addr.sa_data, slave->perm_hwaddr, ETH_ALEN);
- addr.sa_family = slave_dev->type;
- dev_set_mac_address(slave_dev, &addr);
- }
+ /* restore original ("permanent") mac address*/
+ memcpy(addr.sa_data, slave->perm_hwaddr, ETH_ALEN);
+ addr.sa_family = slave_dev->type;
+ dev_set_mac_address(slave_dev, &addr);
- /* restore the original state of the IFF_NOARP flag that might have
- * been set by bond_set_slave_inactive_flags()
- */
- if ((slave->original_flags & IFF_NOARP) == 0) {
- slave_dev->flags &= ~IFF_NOARP;
- }
+ slave_dev->priv_flags &= ~(IFF_MASTER_8023AD | IFF_MASTER_ALB |
+ IFF_SLAVE_INACTIVE);
kfree(slave);
bond_dev->features |= NETIF_F_VLAN_CHALLENGED;
} else {
printk(KERN_WARNING DRV_NAME
- ": Warning: clearing HW address of %s while it "
+ ": %s: Warning: clearing HW address of %s while it "
"still has VLANs.\n",
- bond_dev->name);
+ bond_dev->name, bond_dev->name);
printk(KERN_WARNING DRV_NAME
- ": When re-adding slaves, make sure the bond's "
- "HW address matches its VLANs'.\n");
+ ": %s: When re-adding slaves, make sure the bond's "
+ "HW address matches its VLANs'.\n",
+ bond_dev->name);
}
printk(KERN_INFO DRV_NAME
return res;
}
-static int bond_ethtool_ioctl(struct net_device *bond_dev, struct ifreq *ifr)
-{
- struct ethtool_drvinfo info;
- void __user *addr = ifr->ifr_data;
- uint32_t cmd;
-
- if (get_user(cmd, (uint32_t __user *)addr)) {
- return -EFAULT;
- }
-
- switch (cmd) {
- case ETHTOOL_GDRVINFO:
- if (copy_from_user(&info, addr, sizeof(info))) {
- return -EFAULT;
- }
-
- if (strcmp(info.driver, "ifenslave") == 0) {
- int new_abi_ver;
- char *endptr;
-
- new_abi_ver = simple_strtoul(info.fw_version,
- &endptr, 0);
- if (*endptr) {
- printk(KERN_ERR DRV_NAME
- ": Error: got invalid ABI "
- "version from application\n");
-
- return -EINVAL;
- }
-
- if (orig_app_abi_ver == -1) {
- orig_app_abi_ver = new_abi_ver;
- }
-
- app_abi_ver = new_abi_ver;
- }
-
- strncpy(info.driver, DRV_NAME, 32);
- strncpy(info.version, DRV_VERSION, 32);
- snprintf(info.fw_version, 32, "%d", BOND_ABI_VERSION);
-
- if (copy_to_user(addr, &info, sizeof(info))) {
- return -EFAULT;
- }
-
- return 0;
- default:
- return -EOPNOTSUPP;
- }
-}
-
static int bond_info_query(struct net_device *bond_dev, struct ifbond *info)
{
struct bonding *bond = bond_dev->priv;
/*-------------------------------- Monitoring -------------------------------*/
/* this function is called regularly to monitor each slave's link. */
-static void bond_mii_monitor(struct net_device *bond_dev)
+void bond_mii_monitor(struct net_device *bond_dev)
{
struct bonding *bond = bond_dev->priv;
struct slave *slave, *oldcurrent;
break;
default:
/* Should not happen */
- printk(KERN_ERR "bonding: Error: %s Illegal value (link=%d)\n",
- slave->dev->name, slave->link);
+ printk(KERN_ERR DRV_NAME
+ ": %s: Error: %s Illegal value (link=%d)\n",
+ bond_dev->name,
+ slave->dev->name,
+ slave->link);
goto out;
} /* end of switch (slave->link) */
bond_select_active_slave(bond);
- if (oldcurrent && !bond->curr_active_slave) {
- printk(KERN_INFO DRV_NAME
- ": %s: now running without any active "
- "interface !\n",
- bond_dev->name);
- }
-
write_unlock(&bond->curr_slave_lock);
- }
+ } else
+ bond_set_carrier(bond);
re_arm:
if (bond->params.miimon) {
read_unlock(&bond->lock);
}
+
+static u32 bond_glean_dev_ip(struct net_device *dev)
+{
+ struct in_device *idev;
+ struct in_ifaddr *ifa;
+ u32 addr = 0;
+
+ if (!dev)
+ return 0;
+
+ rcu_read_lock();
+ idev = __in_dev_get_rcu(dev);
+ if (!idev)
+ goto out;
+
+ ifa = idev->ifa_list;
+ if (!ifa)
+ goto out;
+
+ addr = ifa->ifa_local;
+out:
+ rcu_read_unlock();
+ return addr;
+}
+
+static int bond_has_ip(struct bonding *bond)
+{
+ struct vlan_entry *vlan, *vlan_next;
+
+ if (bond->master_ip)
+ return 1;
+
+ if (list_empty(&bond->vlan_list))
+ return 0;
+
+ list_for_each_entry_safe(vlan, vlan_next, &bond->vlan_list,
+ vlan_list) {
+ if (vlan->vlan_ip)
+ return 1;
+ }
+
+ return 0;
+}
+
+/*
+ * We go to the (large) trouble of VLAN tagging ARP frames because
+ * switches in VLAN mode (especially if ports are configured as
+ * "native" to a VLAN) might not pass non-tagged frames.
+ */
+static void bond_arp_send(struct net_device *slave_dev, int arp_op, u32 dest_ip, u32 src_ip, unsigned short vlan_id)
+{
+ struct sk_buff *skb;
+
+ dprintk("arp %d on slave %s: dst %x src %x vid %d\n", arp_op,
+ slave_dev->name, dest_ip, src_ip, vlan_id);
+
+ skb = arp_create(arp_op, ETH_P_ARP, dest_ip, slave_dev, src_ip,
+ NULL, slave_dev->dev_addr, NULL);
+
+ if (!skb) {
+ printk(KERN_ERR DRV_NAME ": ARP packet allocation failed\n");
+ return;
+ }
+ if (vlan_id) {
+ skb = vlan_put_tag(skb, vlan_id);
+ if (!skb) {
+ printk(KERN_ERR DRV_NAME ": failed to insert VLAN tag\n");
+ return;
+ }
+ }
+ arp_xmit(skb);
+}
+
+
static void bond_arp_send_all(struct bonding *bond, struct slave *slave)
{
- int i;
+ int i, vlan_id, rv;
u32 *targets = bond->params.arp_targets;
+ struct vlan_entry *vlan, *vlan_next;
+ struct net_device *vlan_dev;
+ struct flowi fl;
+ struct rtable *rt;
- for (i = 0; (i < BOND_MAX_ARP_TARGETS) && targets[i]; i++) {
- arp_send(ARPOP_REQUEST, ETH_P_ARP, targets[i], slave->dev,
- my_ip, NULL, slave->dev->dev_addr,
- NULL);
+ for (i = 0; (i < BOND_MAX_ARP_TARGETS); i++) {
+ if (!targets[i])
+ continue;
+ dprintk("basa: target %x\n", targets[i]);
+ if (list_empty(&bond->vlan_list)) {
+ dprintk("basa: empty vlan: arp_send\n");
+ bond_arp_send(slave->dev, ARPOP_REQUEST, targets[i],
+ bond->master_ip, 0);
+ continue;
+ }
+
+ /*
+ * If VLANs are configured, we do a route lookup to
+ * determine which VLAN interface would be used, so we
+ * can tag the ARP with the proper VLAN tag.
+ */
+ memset(&fl, 0, sizeof(fl));
+ fl.fl4_dst = targets[i];
+ fl.fl4_tos = RTO_ONLINK;
+
+ rv = ip_route_output_key(&rt, &fl);
+ if (rv) {
+ if (net_ratelimit()) {
+ printk(KERN_WARNING DRV_NAME
+ ": %s: no route to arp_ip_target %u.%u.%u.%u\n",
+ bond->dev->name, NIPQUAD(fl.fl4_dst));
+ }
+ continue;
+ }
+
+ /*
+ * This target is not on a VLAN
+ */
+ if (rt->u.dst.dev == bond->dev) {
+ ip_rt_put(rt);
+ dprintk("basa: rtdev == bond->dev: arp_send\n");
+ bond_arp_send(slave->dev, ARPOP_REQUEST, targets[i],
+ bond->master_ip, 0);
+ continue;
+ }
+
+ vlan_id = 0;
+ list_for_each_entry_safe(vlan, vlan_next, &bond->vlan_list,
+ vlan_list) {
+ vlan_dev = bond->vlgrp->vlan_devices[vlan->vlan_id];
+ if (vlan_dev == rt->u.dst.dev) {
+ vlan_id = vlan->vlan_id;
+ dprintk("basa: vlan match on %s %d\n",
+ vlan_dev->name, vlan_id);
+ break;
+ }
+ }
+
+ if (vlan_id) {
+ ip_rt_put(rt);
+ bond_arp_send(slave->dev, ARPOP_REQUEST, targets[i],
+ vlan->vlan_ip, vlan_id);
+ continue;
+ }
+
+ if (net_ratelimit()) {
+ printk(KERN_WARNING DRV_NAME
+ ": %s: no path to arp_ip_target %u.%u.%u.%u via rt.dev %s\n",
+ bond->dev->name, NIPQUAD(fl.fl4_dst),
+ rt->u.dst.dev ? rt->u.dst.dev->name : "NULL");
+ }
+ ip_rt_put(rt);
+ }
+}
+
+/*
+ * Kick out a gratuitous ARP for an IP on the bonding master plus one
+ * for each VLAN above us.
+ */
+static void bond_send_gratuitous_arp(struct bonding *bond)
+{
+ struct slave *slave = bond->curr_active_slave;
+ struct vlan_entry *vlan;
+ struct net_device *vlan_dev;
+
+ dprintk("bond_send_grat_arp: bond %s slave %s\n", bond->dev->name,
+ slave ? slave->dev->name : "NULL");
+ if (!slave)
+ return;
+
+ if (bond->master_ip) {
+ bond_arp_send(slave->dev, ARPOP_REPLY, bond->master_ip,
+ bond->master_ip, 0);
+ }
+
+ list_for_each_entry(vlan, &bond->vlan_list, vlan_list) {
+ vlan_dev = bond->vlgrp->vlan_devices[vlan->vlan_id];
+ if (vlan->vlan_ip) {
+ bond_arp_send(slave->dev, ARPOP_REPLY, vlan->vlan_ip,
+ vlan->vlan_ip, vlan->vlan_id);
+ }
}
}
* arp is transmitted to generate traffic. see activebackup_arp_monitor for
* arp monitoring in active backup mode.
*/
-static void bond_loadbalance_arp_mon(struct net_device *bond_dev)
+void bond_loadbalance_arp_mon(struct net_device *bond_dev)
{
struct bonding *bond = bond_dev->priv;
struct slave *slave, *oldcurrent;
*/
if (((jiffies - slave->dev->trans_start) >= (2*delta_in_ticks)) ||
(((jiffies - slave->dev->last_rx) >= (2*delta_in_ticks)) &&
- my_ip)) {
+ bond_has_ip(bond))) {
slave->link = BOND_LINK_DOWN;
slave->state = BOND_STATE_BACKUP;
bond_select_active_slave(bond);
- if (oldcurrent && !bond->curr_active_slave) {
- printk(KERN_INFO DRV_NAME
- ": %s: now running without any active "
- "interface !\n",
- bond_dev->name);
- }
-
write_unlock(&bond->curr_slave_lock);
}
* may have received.
* see loadbalance_arp_monitor for arp monitoring in load balancing mode
*/
-static void bond_activebackup_arp_mon(struct net_device *bond_dev)
+void bond_activebackup_arp_mon(struct net_device *bond_dev)
{
struct bonding *bond = bond_dev->priv;
struct slave *slave;
bond->current_arp_slave = NULL;
}
+ bond_set_carrier(bond);
+
if (slave == bond->curr_active_slave) {
printk(KERN_INFO DRV_NAME
": %s: %s is up and now the "
"active interface\n",
bond_dev->name,
slave->dev->name);
+ netif_carrier_on(bond->dev);
} else {
printk(KERN_INFO DRV_NAME
": %s: backup interface %s is "
if ((slave != bond->curr_active_slave) &&
(!bond->current_arp_slave) &&
(((jiffies - slave->dev->last_rx) >= 3*delta_in_ticks) &&
- my_ip)) {
+ bond_has_ip(bond))) {
/* a backup slave has gone down; three times
* the delta allows the current slave to be
* taken out before the backup slave.
* if it is up and needs to take over as the curr_active_slave
*/
if ((((jiffies - slave->dev->trans_start) >= (2*delta_in_ticks)) ||
- (((jiffies - slave->dev->last_rx) >= (2*delta_in_ticks)) &&
- my_ip)) &&
+ (((jiffies - slave->dev->last_rx) >= (2*delta_in_ticks)) &&
+ bond_has_ip(bond))) &&
((jiffies - slave->jiffies) >= 2*delta_in_ticks)) {
slave->link = BOND_LINK_DOWN;
/* the current slave must tx an arp to ensure backup slaves
* rx traffic
*/
- if (slave && my_ip) {
+ if (slave && bond_has_ip(bond)) {
bond_arp_send_all(bond, slave);
}
}
{
struct bonding *bond = seq->private;
struct slave *curr;
+ int i;
+ u32 target;
read_lock(&bond->curr_slave_lock);
curr = bond->curr_active_slave;
seq_printf(seq, "Bonding Mode: %s\n",
bond_mode_name(bond->params.mode));
+ if (bond->params.mode == BOND_MODE_XOR ||
+ bond->params.mode == BOND_MODE_8023AD) {
+ seq_printf(seq, "Transmit Hash Policy: %s (%d)\n",
+ xmit_hashtype_tbl[bond->params.xmit_policy].modename,
+ bond->params.xmit_policy);
+ }
+
if (USES_PRIMARY(bond->params.mode)) {
seq_printf(seq, "Primary Slave: %s\n",
- (bond->params.primary[0]) ?
- bond->params.primary : "None");
+ (bond->primary_slave) ?
+ bond->primary_slave->dev->name : "None");
seq_printf(seq, "Currently Active Slave: %s\n",
(curr) ? curr->dev->name : "None");
}
- seq_printf(seq, "MII Status: %s\n", (curr) ? "up" : "down");
+ seq_printf(seq, "MII Status: %s\n", netif_carrier_ok(bond->dev) ?
+ "up" : "down");
seq_printf(seq, "MII Polling Interval (ms): %d\n", bond->params.miimon);
seq_printf(seq, "Up Delay (ms): %d\n",
bond->params.updelay * bond->params.miimon);
seq_printf(seq, "Down Delay (ms): %d\n",
bond->params.downdelay * bond->params.miimon);
+
+ /* ARP information */
+ if(bond->params.arp_interval > 0) {
+ int printed=0;
+ seq_printf(seq, "ARP Polling Interval (ms): %d\n",
+ bond->params.arp_interval);
+
+ seq_printf(seq, "ARP IP target/s (n.n.n.n form):");
+
+ for(i = 0; (i < BOND_MAX_ARP_TARGETS) ;i++) {
+ if (!bond->params.arp_targets[i])
+ continue;
+ if (printed)
+ seq_printf(seq, ",");
+ target = ntohl(bond->params.arp_targets[i]);
+ seq_printf(seq, " %d.%d.%d.%d", HIPQUAD(target));
+ printed = 1;
+ }
+ seq_printf(seq, "\n");
+ }
+
if (bond->params.mode == BOND_MODE_8023AD) {
struct ad_info ad_info;
seq_printf(seq, "Link Failure Count: %d\n",
slave->link_failure_count);
- if (app_abi_ver >= 1) {
- seq_printf(seq,
- "Permanent HW addr: %02x:%02x:%02x:%02x:%02x:%02x\n",
- slave->perm_hwaddr[0],
- slave->perm_hwaddr[1],
- slave->perm_hwaddr[2],
- slave->perm_hwaddr[3],
- slave->perm_hwaddr[4],
- slave->perm_hwaddr[5]);
- }
+ seq_printf(seq,
+ "Permanent HW addr: %02x:%02x:%02x:%02x:%02x:%02x\n",
+ slave->perm_hwaddr[0], slave->perm_hwaddr[1],
+ slave->perm_hwaddr[2], slave->perm_hwaddr[3],
+ slave->perm_hwaddr[4], slave->perm_hwaddr[5]);
if (bond->params.mode == BOND_MODE_8023AD) {
const struct aggregator *agg
bond_remove_proc_entry(bond);
bond_create_proc_entry(bond);
#endif
-
+ down_write(&(bonding_rwsem));
+ bond_destroy_sysfs_entry(bond);
+ bond_create_sysfs_entry(bond);
+ up_write(&(bonding_rwsem));
return NOTIFY_DONE;
}
static int bond_slave_netdev_event(unsigned long event, struct net_device *slave_dev)
{
struct net_device *bond_dev = slave_dev->master;
+ struct bonding *bond = bond_dev->priv;
switch (event) {
case NETDEV_UNREGISTER:
* TODO: handle changing the primary's name
*/
break;
+ case NETDEV_FEAT_CHANGE:
+ bond_compute_features(bond);
+ break;
default:
break;
}
* bond_netdev_event: handle netdev notifier chain events.
*
* This function receives events for the netdev chain. The caller (an
- * ioctl handler calling notifier_call_chain) holds the necessary
+ * ioctl handler calling blocking_notifier_call_chain) holds the necessary
* locks for us to safely manipulate the slave devices (RTNL lock,
* dev_probe_lock).
*/
return NOTIFY_DONE;
}
+/*
+ * bond_inetaddr_event: handle inetaddr notifier chain events.
+ *
+ * We keep track of device IPs primarily to use as source addresses in
+ * ARP monitor probes (rather than spewing out broadcasts all the time).
+ *
+ * We track one IP for the main device (if it has one), plus one per VLAN.
+ */
+static int bond_inetaddr_event(struct notifier_block *this, unsigned long event, void *ptr)
+{
+ struct in_ifaddr *ifa = ptr;
+ struct net_device *vlan_dev, *event_dev = ifa->ifa_dev->dev;
+ struct bonding *bond, *bond_next;
+ struct vlan_entry *vlan, *vlan_next;
+
+ list_for_each_entry_safe(bond, bond_next, &bond_dev_list, bond_list) {
+ if (bond->dev == event_dev) {
+ switch (event) {
+ case NETDEV_UP:
+ bond->master_ip = ifa->ifa_local;
+ return NOTIFY_OK;
+ case NETDEV_DOWN:
+ bond->master_ip = bond_glean_dev_ip(bond->dev);
+ return NOTIFY_OK;
+ default:
+ return NOTIFY_DONE;
+ }
+ }
+
+ if (list_empty(&bond->vlan_list))
+ continue;
+
+ list_for_each_entry_safe(vlan, vlan_next, &bond->vlan_list,
+ vlan_list) {
+ vlan_dev = bond->vlgrp->vlan_devices[vlan->vlan_id];
+ if (vlan_dev == event_dev) {
+ switch (event) {
+ case NETDEV_UP:
+ vlan->vlan_ip = ifa->ifa_local;
+ return NOTIFY_OK;
+ case NETDEV_DOWN:
+ vlan->vlan_ip =
+ bond_glean_dev_ip(vlan_dev);
+ return NOTIFY_OK;
+ default:
+ return NOTIFY_DONE;
+ }
+ }
+ }
+ }
+ return NOTIFY_DONE;
+}
+
static struct notifier_block bond_netdev_notifier = {
.notifier_call = bond_netdev_event,
};
+static struct notifier_block bond_inetaddr_notifier = {
+ .notifier_call = bond_inetaddr_event,
+};
+
/*-------------------------- Packet type handling ---------------------------*/
/* register to receive lacpdus on a bond */
dev_remove_pack(&(BOND_AD_INFO(bond).ad_pkt_type));
}
+/*---------------------------- Hashing Policies -----------------------------*/
+
+/*
+ * Hash for the the output device based upon layer 3 and layer 4 data. If
+ * the packet is a frag or not TCP or UDP, just use layer 3 data. If it is
+ * altogether not IP, mimic bond_xmit_hash_policy_l2()
+ */
+static int bond_xmit_hash_policy_l34(struct sk_buff *skb,
+ struct net_device *bond_dev, int count)
+{
+ struct ethhdr *data = (struct ethhdr *)skb->data;
+ struct iphdr *iph = skb->nh.iph;
+ u16 *layer4hdr = (u16 *)((u32 *)iph + iph->ihl);
+ int layer4_xor = 0;
+
+ if (skb->protocol == __constant_htons(ETH_P_IP)) {
+ if (!(iph->frag_off & __constant_htons(IP_MF|IP_OFFSET)) &&
+ (iph->protocol == IPPROTO_TCP ||
+ iph->protocol == IPPROTO_UDP)) {
+ layer4_xor = htons((*layer4hdr ^ *(layer4hdr + 1)));
+ }
+ return (layer4_xor ^
+ ((ntohl(iph->saddr ^ iph->daddr)) & 0xffff)) % count;
+
+ }
+
+ return (data->h_dest[5] ^ bond_dev->dev_addr[5]) % count;
+}
+
+/*
+ * Hash for the output device based upon layer 2 data
+ */
+static int bond_xmit_hash_policy_l2(struct sk_buff *skb,
+ struct net_device *bond_dev, int count)
+{
+ struct ethhdr *data = (struct ethhdr *)skb->data;
+
+ return (data->h_dest[5] ^ bond_dev->dev_addr[5]) % count;
+}
+
/*-------------------------- Device entry points ----------------------------*/
static int bond_open(struct net_device *bond_dev)
struct ifslave k_sinfo;
struct ifslave __user *u_sinfo = NULL;
struct mii_ioctl_data *mii = NULL;
- int prev_abi_ver = orig_app_abi_ver;
int res = 0;
dprintk("bond_ioctl: master=%s, cmd=%d\n",
bond_dev->name, cmd);
switch (cmd) {
- case SIOCETHTOOL:
- return bond_ethtool_ioctl(bond_dev, ifr);
case SIOCGMIIPHY:
mii = if_mii(ifr);
if (!mii) {
mii->val_out = 0;
read_lock_bh(&bond->lock);
read_lock(&bond->curr_slave_lock);
- if (bond->curr_active_slave) {
+ if (netif_carrier_ok(bond->dev)) {
mii->val_out = BMSR_LSTATUS;
}
read_unlock(&bond->curr_slave_lock);
return -EPERM;
}
- if (orig_app_abi_ver == -1) {
- /* no orig_app_abi_ver was provided yet, so we'll use the
- * current one from now on, even if it's 0
- */
- orig_app_abi_ver = app_abi_ver;
-
- } else if (orig_app_abi_ver != app_abi_ver) {
- printk(KERN_ERR DRV_NAME
- ": Error: already using ifenslave ABI version %d; to "
- "upgrade ifenslave to version %d, you must first "
- "reload bonding.\n",
- orig_app_abi_ver, app_abi_ver);
- return -EINVAL;
- }
-
+ down_write(&(bonding_rwsem));
slave_dev = dev_get_by_name(ifr->ifr_slave);
dprintk("slave_dev=%p: \n", slave_dev);
dev_put(slave_dev);
}
- if (res < 0) {
- /* The ioctl failed, so there's no point in changing the
- * orig_app_abi_ver. We'll restore it's value just in case
- * we've changed it earlier in this function.
- */
- orig_app_abi_ver = prev_abi_ver;
- }
-
+ up_write(&(bonding_rwsem));
return res;
}
bond_for_each_slave(bond, slave, i) {
dprintk("s %p s->p %p c_m %p\n", slave,
slave->prev, slave->dev->change_mtu);
+
res = dev_set_mtu(slave->dev, new_mtu);
if (res) {
return 0;
}
+static void bond_activebackup_xmit_copy(struct sk_buff *skb,
+ struct bonding *bond,
+ struct slave *slave)
+{
+ struct sk_buff *skb2 = skb_copy(skb, GFP_ATOMIC);
+ struct ethhdr *eth_data;
+ u8 *hwaddr;
+ int res;
+
+ if (!skb2) {
+ printk(KERN_ERR DRV_NAME ": Error: "
+ "bond_activebackup_xmit_copy(): skb_copy() failed\n");
+ return;
+ }
+
+ skb2->mac.raw = (unsigned char *)skb2->data;
+ eth_data = eth_hdr(skb2);
+
+ /* Pick an appropriate source MAC address
+ * -- use slave's perm MAC addr, unless used by bond
+ * -- otherwise, borrow active slave's perm MAC addr
+ * since that will not be used
+ */
+ hwaddr = slave->perm_hwaddr;
+ if (!memcmp(eth_data->h_source, hwaddr, ETH_ALEN))
+ hwaddr = bond->curr_active_slave->perm_hwaddr;
+
+ /* Set source MAC address appropriately */
+ memcpy(eth_data->h_source, hwaddr, ETH_ALEN);
+
+ res = bond_dev_queue_xmit(bond, skb2, slave->dev);
+ if (res)
+ dev_kfree_skb(skb2);
+
+ return;
+}
+
/*
* in active-backup mode, we know that bond->curr_active_slave is always valid if
* the bond has a usable interface.
struct bonding *bond = bond_dev->priv;
int res = 1;
- /* if we are sending arp packets, try to at least
- identify our own ip address */
- if (bond->params.arp_interval && !my_ip &&
- (skb->protocol == __constant_htons(ETH_P_ARP))) {
- char *the_ip = (char *)skb->data +
- sizeof(struct ethhdr) +
- sizeof(struct arphdr) +
- ETH_ALEN;
- memcpy(&my_ip, the_ip, 4);
- }
-
read_lock(&bond->lock);
read_lock(&bond->curr_slave_lock);
goto out;
}
- if (bond->curr_active_slave) { /* one usable interface */
- res = bond_dev_queue_xmit(bond, skb, bond->curr_active_slave->dev);
+ if (!bond->curr_active_slave)
+ goto out;
+
+ /* Xmit IGMP frames on all slaves to ensure rapid fail-over
+ for multicast traffic on snooping switches */
+ if (skb->protocol == __constant_htons(ETH_P_IP) &&
+ skb->nh.iph->protocol == IPPROTO_IGMP) {
+ struct slave *slave, *active_slave;
+ int i;
+
+ active_slave = bond->curr_active_slave;
+ bond_for_each_slave_from_to(bond, slave, i, active_slave->next,
+ active_slave->prev)
+ if (IS_UP(slave->dev) &&
+ (slave->link == BOND_LINK_UP))
+ bond_activebackup_xmit_copy(skb, bond, slave);
}
+ res = bond_dev_queue_xmit(bond, skb, bond->curr_active_slave->dev);
+
out:
if (res) {
/* no suitable interface, frame not sent */
}
/*
- * in XOR mode, we determine the output device by performing xor on
- * the source and destination hw adresses. If this device is not
- * enabled, find the next slave following this xor slave.
+ * In bond_xmit_xor() , we determine the output device by using a pre-
+ * determined xmit_hash_policy(), If the selected device is not enabled,
+ * find the next active slave.
*/
static int bond_xmit_xor(struct sk_buff *skb, struct net_device *bond_dev)
{
struct bonding *bond = bond_dev->priv;
- struct ethhdr *data = (struct ethhdr *)skb->data;
struct slave *slave, *start_at;
int slave_no;
int i;
goto out;
}
- slave_no = (data->h_dest[5]^bond_dev->dev_addr[5]) % bond->slave_cnt;
+ slave_no = bond->xmit_hash_policy(skb, bond_dev, bond->slave_cnt);
bond_for_each_slave(bond, slave, i) {
slave_no--;
struct sk_buff *skb2 = skb_clone(skb, GFP_ATOMIC);
if (!skb2) {
printk(KERN_ERR DRV_NAME
- ": Error: bond_xmit_broadcast(): "
- "skb_clone() failed\n");
+ ": %s: Error: bond_xmit_broadcast(): "
+ "skb_clone() failed\n",
+ bond_dev->name);
continue;
}
/*
* set bond mode specific net device operations
*/
-static inline void bond_set_mode_ops(struct net_device *bond_dev, int mode)
+void bond_set_mode_ops(struct bonding *bond, int mode)
{
+ struct net_device *bond_dev = bond->dev;
+
switch (mode) {
case BOND_MODE_ROUNDROBIN:
bond_dev->hard_start_xmit = bond_xmit_roundrobin;
break;
case BOND_MODE_XOR:
bond_dev->hard_start_xmit = bond_xmit_xor;
+ if (bond->params.xmit_policy == BOND_XMIT_POLICY_LAYER34)
+ bond->xmit_hash_policy = bond_xmit_hash_policy_l34;
+ else
+ bond->xmit_hash_policy = bond_xmit_hash_policy_l2;
break;
case BOND_MODE_BROADCAST:
bond_dev->hard_start_xmit = bond_xmit_broadcast;
break;
case BOND_MODE_8023AD:
+ bond_set_master_3ad_flags(bond);
bond_dev->hard_start_xmit = bond_3ad_xmit_xor;
+ if (bond->params.xmit_policy == BOND_XMIT_POLICY_LAYER34)
+ bond->xmit_hash_policy = bond_xmit_hash_policy_l34;
+ else
+ bond->xmit_hash_policy = bond_xmit_hash_policy_l2;
break;
- case BOND_MODE_TLB:
case BOND_MODE_ALB:
+ bond_set_master_alb_flags(bond);
+ /* FALLTHRU */
+ case BOND_MODE_TLB:
bond_dev->hard_start_xmit = bond_alb_xmit;
bond_dev->set_mac_address = bond_alb_set_mac_address;
break;
default:
/* Should never happen, mode already checked */
printk(KERN_ERR DRV_NAME
- ": Error: Unknown bonding mode %d\n",
+ ": %s: Error: Unknown bonding mode %d\n",
+ bond_dev->name,
mode);
break;
}
}
+static void bond_ethtool_get_drvinfo(struct net_device *bond_dev,
+ struct ethtool_drvinfo *drvinfo)
+{
+ strncpy(drvinfo->driver, DRV_NAME, 32);
+ strncpy(drvinfo->version, DRV_VERSION, 32);
+ snprintf(drvinfo->fw_version, 32, "%d", BOND_ABI_VERSION);
+}
+
+static struct ethtool_ops bond_ethtool_ops = {
+ .get_tx_csum = ethtool_op_get_tx_csum,
+ .get_tso = ethtool_op_get_tso,
+ .get_ufo = ethtool_op_get_ufo,
+ .get_sg = ethtool_op_get_sg,
+ .get_drvinfo = bond_ethtool_get_drvinfo,
+};
+
/*
* Does not allocate but creates a /proc entry.
* Allowed to fail.
*/
-static int __init bond_init(struct net_device *bond_dev, struct bond_params *params)
+static int bond_init(struct net_device *bond_dev, struct bond_params *params)
{
struct bonding *bond = bond_dev->priv;
bond_dev->stop = bond_close;
bond_dev->get_stats = bond_get_stats;
bond_dev->do_ioctl = bond_do_ioctl;
+ bond_dev->ethtool_ops = &bond_ethtool_ops;
bond_dev->set_multicast_list = bond_set_multicast_list;
bond_dev->change_mtu = bond_change_mtu;
bond_dev->set_mac_address = bond_set_mac_address;
- bond_set_mode_ops(bond_dev, bond->params.mode);
+ bond_set_mode_ops(bond, bond->params.mode);
bond_dev->destructor = free_netdev;
*/
bond_dev->features |= NETIF_F_VLAN_CHALLENGED;
- /* don't acquire bond device's xmit_lock when
+ /* don't acquire bond device's netif_tx_lock when
* transmitting */
bond_dev->features |= NETIF_F_LLTX;
/* De-initialize device specific data.
* Caller must hold rtnl_lock.
*/
-static inline void bond_deinit(struct net_device *bond_dev)
+void bond_deinit(struct net_device *bond_dev)
{
struct bonding *bond = bond_dev->priv;
* Convert string input module parms. Accept either the
* number of the mode or its string name.
*/
-static inline int bond_parse_parm(char *mode_arg, struct bond_parm_tbl *tbl)
+int bond_parse_parm(char *mode_arg, struct bond_parm_tbl *tbl)
{
int i;
}
}
+ if (xmit_hash_policy) {
+ if ((bond_mode != BOND_MODE_XOR) &&
+ (bond_mode != BOND_MODE_8023AD)) {
+ printk(KERN_INFO DRV_NAME
+ ": xor_mode param is irrelevant in mode %s\n",
+ bond_mode_name(bond_mode));
+ } else {
+ xmit_hashtype = bond_parse_parm(xmit_hash_policy,
+ xmit_hashtype_tbl);
+ if (xmit_hashtype == -1) {
+ printk(KERN_ERR DRV_NAME
+ ": Error: Invalid xmit_hash_policy \"%s\"\n",
+ xmit_hash_policy == NULL ? "NULL" :
+ xmit_hash_policy);
+ return -EINVAL;
+ }
+ }
+ }
+
if (lacp_rate) {
if (bond_mode != BOND_MODE_8023AD) {
printk(KERN_INFO DRV_NAME
if (max_bonds < 1 || max_bonds > INT_MAX) {
printk(KERN_WARNING DRV_NAME
": Warning: max_bonds (%d) not in range %d-%d, so it "
- "was reset to BOND_DEFAULT_MAX_BONDS (%d)",
+ "was reset to BOND_DEFAULT_MAX_BONDS (%d)\n",
max_bonds, 1, INT_MAX, BOND_DEFAULT_MAX_BONDS);
max_bonds = BOND_DEFAULT_MAX_BONDS;
}
/* fill params struct with the proper values */
params->mode = bond_mode;
+ params->xmit_policy = xmit_hashtype;
params->miimon = miimon;
params->arp_interval = arp_interval;
params->updelay = updelay;
return 0;
}
+static struct lock_class_key bonding_netdev_xmit_lock_key;
+
+/* Create a new bond based on the specified name and bonding parameters.
+ * Caller must NOT hold rtnl_lock; we need to release it here before we
+ * set up our sysfs entries.
+ */
+int bond_create(char *name, struct bond_params *params, struct bonding **newbond)
+{
+ struct net_device *bond_dev;
+ int res;
+
+ rtnl_lock();
+ bond_dev = alloc_netdev(sizeof(struct bonding), name, ether_setup);
+ if (!bond_dev) {
+ printk(KERN_ERR DRV_NAME
+ ": %s: eek! can't alloc netdev!\n",
+ name);
+ res = -ENOMEM;
+ goto out_rtnl;
+ }
+
+ /* bond_init() must be called after dev_alloc_name() (for the
+ * /proc files), but before register_netdevice(), because we
+ * need to set function pointers.
+ */
+
+ res = bond_init(bond_dev, params);
+ if (res < 0) {
+ goto out_netdev;
+ }
+
+ SET_MODULE_OWNER(bond_dev);
+
+ res = register_netdevice(bond_dev);
+ if (res < 0) {
+ goto out_bond;
+ }
+
+ lockdep_set_class(&bond_dev->_xmit_lock, &bonding_netdev_xmit_lock_key);
+
+ if (newbond)
+ *newbond = bond_dev->priv;
+
+ netif_carrier_off(bond_dev);
+
+ rtnl_unlock(); /* allows sysfs registration of net device */
+ res = bond_create_sysfs_entry(bond_dev->priv);
+ goto done;
+out_bond:
+ bond_deinit(bond_dev);
+out_netdev:
+ free_netdev(bond_dev);
+out_rtnl:
+ rtnl_unlock();
+done:
+ return res;
+}
+
static int __init bonding_init(void)
{
- struct bond_params params;
int i;
int res;
+ char new_bond_name[8]; /* Enough room for 999 bonds at init. */
printk(KERN_INFO "%s", version);
- res = bond_check_params(¶ms);
+ res = bond_check_params(&bonding_defaults);
if (res) {
- return res;
+ goto out;
}
- rtnl_lock();
-
#ifdef CONFIG_PROC_FS
bond_create_proc_dir();
#endif
-
for (i = 0; i < max_bonds; i++) {
- struct net_device *bond_dev;
-
- bond_dev = alloc_netdev(sizeof(struct bonding), "", ether_setup);
- if (!bond_dev) {
- res = -ENOMEM;
- goto out_err;
- }
-
- res = dev_alloc_name(bond_dev, "bond%d");
- if (res < 0) {
- free_netdev(bond_dev);
- goto out_err;
- }
-
- /* bond_init() must be called after dev_alloc_name() (for the
- * /proc files), but before register_netdevice(), because we
- * need to set function pointers.
- */
- res = bond_init(bond_dev, ¶ms);
- if (res < 0) {
- free_netdev(bond_dev);
- goto out_err;
- }
-
- SET_MODULE_OWNER(bond_dev);
-
- res = register_netdevice(bond_dev);
- if (res < 0) {
- bond_deinit(bond_dev);
- free_netdev(bond_dev);
- goto out_err;
- }
+ sprintf(new_bond_name, "bond%d",i);
+ res = bond_create(new_bond_name,&bonding_defaults, NULL);
+ if (res)
+ goto err;
}
- rtnl_unlock();
- register_netdevice_notifier(&bond_netdev_notifier);
+ res = bond_create_sysfs();
+ if (res)
+ goto err;
- return 0;
+ register_netdevice_notifier(&bond_netdev_notifier);
+ register_inetaddr_notifier(&bond_inetaddr_notifier);
-out_err:
- /* free and unregister all bonds that were successfully added */
+ goto out;
+err:
+ rtnl_lock();
bond_free_all();
-
+ bond_destroy_sysfs();
rtnl_unlock();
-
+out:
return res;
+
}
static void __exit bonding_exit(void)
{
unregister_netdevice_notifier(&bond_netdev_notifier);
+ unregister_inetaddr_notifier(&bond_inetaddr_notifier);
rtnl_lock();
bond_free_all();
+ bond_destroy_sysfs();
rtnl_unlock();
}