/*******************************************************************************
- Copyright(c) 1999 - 2004 Intel Corporation. All rights reserved.
+ Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
static int32_t e1000_acquire_eeprom(struct e1000_hw *hw);
static void e1000_release_eeprom(struct e1000_hw *hw);
static void e1000_standby_eeprom(struct e1000_hw *hw);
-static int32_t e1000_id_led_init(struct e1000_hw * hw);
static int32_t e1000_set_vco_speed(struct e1000_hw *hw);
+static int32_t e1000_polarity_reversal_workaround(struct e1000_hw *hw);
static int32_t e1000_set_phy_mode(struct e1000_hw *hw);
+static int32_t e1000_host_if_read_cookie(struct e1000_hw *hw, uint8_t *buffer);
+static uint8_t e1000_calculate_mng_checksum(char *buffer, uint32_t length);
+static uint8_t e1000_arc_subsystem_valid(struct e1000_hw *hw);
+static int32_t e1000_check_downshift(struct e1000_hw *hw);
+static int32_t e1000_check_polarity(struct e1000_hw *hw, uint16_t *polarity);
+static void e1000_clear_hw_cntrs(struct e1000_hw *hw);
+static void e1000_clear_vfta(struct e1000_hw *hw);
+static int32_t e1000_commit_shadow_ram(struct e1000_hw *hw);
+static int32_t e1000_config_dsp_after_link_change(struct e1000_hw *hw,
+ boolean_t link_up);
+static int32_t e1000_config_fc_after_link_up(struct e1000_hw *hw);
+static int32_t e1000_detect_gig_phy(struct e1000_hw *hw);
+static int32_t e1000_get_auto_rd_done(struct e1000_hw *hw);
+static int32_t e1000_get_cable_length(struct e1000_hw *hw,
+ uint16_t *min_length,
+ uint16_t *max_length);
+static int32_t e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw);
+static int32_t e1000_get_phy_cfg_done(struct e1000_hw *hw);
+static int32_t e1000_id_led_init(struct e1000_hw * hw);
+static void e1000_init_rx_addrs(struct e1000_hw *hw);
+static boolean_t e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw);
+static int32_t e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd);
+static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw);
+static int32_t e1000_read_eeprom_eerd(struct e1000_hw *hw, uint16_t offset,
+ uint16_t words, uint16_t *data);
+static int32_t e1000_set_d0_lplu_state(struct e1000_hw *hw, boolean_t active);
+static int32_t e1000_set_d3_lplu_state(struct e1000_hw *hw, boolean_t active);
+static int32_t e1000_wait_autoneg(struct e1000_hw *hw);
+
+static void e1000_write_reg_io(struct e1000_hw *hw, uint32_t offset,
+ uint32_t value);
+
+#define E1000_WRITE_REG_IO(a, reg, val) \
+ e1000_write_reg_io((a), E1000_##reg, val)
+static int32_t e1000_configure_kmrn_for_10_100(struct e1000_hw *hw);
+static int32_t e1000_configure_kmrn_for_1000(struct e1000_hw *hw);
/* IGP cable length table */
static const
100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110,
110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120, 120, 120};
+static const
+uint16_t e1000_igp_2_cable_length_table[IGP02E1000_AGC_LENGTH_TABLE_SIZE] =
+ { 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21,
+ 0, 0, 0, 3, 6, 10, 13, 16, 19, 23, 26, 29, 32, 35, 38, 41,
+ 6, 10, 14, 18, 22, 26, 30, 33, 37, 41, 44, 48, 51, 54, 58, 61,
+ 21, 26, 31, 35, 40, 44, 49, 53, 57, 61, 65, 68, 72, 75, 79, 82,
+ 40, 45, 51, 56, 61, 66, 70, 75, 79, 83, 87, 91, 94, 98, 101, 104,
+ 60, 66, 72, 77, 82, 87, 92, 96, 100, 104, 108, 111, 114, 117, 119, 121,
+ 83, 89, 95, 100, 105, 109, 113, 116, 119, 122, 124,
+ 104, 109, 114, 118, 121, 124};
+
/******************************************************************************
* Set the phy type member in the hw struct.
{
DEBUGFUNC("e1000_set_phy_type");
+ if(hw->mac_type == e1000_undefined)
+ return -E1000_ERR_PHY_TYPE;
+
switch(hw->phy_id) {
case M88E1000_E_PHY_ID:
case M88E1000_I_PHY_ID:
case M88E1011_I_PHY_ID:
+ case M88E1111_I_PHY_ID:
hw->phy_type = e1000_phy_m88;
break;
case IGP01E1000_I_PHY_ID:
hw->phy_type = e1000_phy_igp;
break;
}
+ case GG82563_E_PHY_ID:
+ if (hw->mac_type == e1000_80003es2lan) {
+ hw->phy_type = e1000_phy_gg82563;
+ break;
+ }
/* Fall Through */
default:
/* Should never have loaded on this device */
static void
e1000_phy_init_script(struct e1000_hw *hw)
{
+ uint32_t ret_val;
+ uint16_t phy_saved_data;
+
DEBUGFUNC("e1000_phy_init_script");
if(hw->phy_init_script) {
msec_delay(20);
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of this routine. */
+ ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
+
+ /* Disabled the PHY transmitter */
+ e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
+
+ msec_delay(20);
+
e1000_write_phy_reg(hw,0x0000,0x0140);
msec_delay(5);
- if(hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547) {
+ switch(hw->mac_type) {
+ case e1000_82541:
+ case e1000_82547:
e1000_write_phy_reg(hw, 0x1F95, 0x0001);
e1000_write_phy_reg(hw, 0x1F71, 0xBD21);
e1000_write_phy_reg(hw, 0x1F96, 0x003F);
e1000_write_phy_reg(hw, 0x2010, 0x0008);
- } else {
+ break;
+
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
e1000_write_phy_reg(hw, 0x1F73, 0x0099);
+ break;
+ default:
+ break;
}
e1000_write_phy_reg(hw, 0x0000, 0x3300);
+ msec_delay(20);
+
+ /* Now enable the transmitter */
+ e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
+
if(hw->mac_type == e1000_82547) {
uint16_t fused, fine, coarse;
case E1000_DEV_ID_82546GB_COPPER:
case E1000_DEV_ID_82546GB_FIBER:
case E1000_DEV_ID_82546GB_SERDES:
+ case E1000_DEV_ID_82546GB_PCIE:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
hw->mac_type = e1000_82546_rev_3;
break;
case E1000_DEV_ID_82541EI:
break;
case E1000_DEV_ID_82541ER:
case E1000_DEV_ID_82541GI:
+ case E1000_DEV_ID_82541GI_LF:
case E1000_DEV_ID_82541GI_MOBILE:
hw->mac_type = e1000_82541_rev_2;
break;
case E1000_DEV_ID_82547GI:
hw->mac_type = e1000_82547_rev_2;
break;
+ case E1000_DEV_ID_82571EB_COPPER:
+ case E1000_DEV_ID_82571EB_FIBER:
+ case E1000_DEV_ID_82571EB_SERDES:
+ hw->mac_type = e1000_82571;
+ break;
+ case E1000_DEV_ID_82572EI_COPPER:
+ case E1000_DEV_ID_82572EI_FIBER:
+ case E1000_DEV_ID_82572EI_SERDES:
+ hw->mac_type = e1000_82572;
+ break;
+ case E1000_DEV_ID_82573E:
+ case E1000_DEV_ID_82573E_IAMT:
+ case E1000_DEV_ID_82573L:
+ hw->mac_type = e1000_82573;
+ break;
+ case E1000_DEV_ID_80003ES2LAN_COPPER_DPT:
+ case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
+ hw->mac_type = e1000_80003es2lan;
+ break;
default:
/* Should never have loaded on this device */
return -E1000_ERR_MAC_TYPE;
}
+ switch(hw->mac_type) {
+ case e1000_80003es2lan:
+ hw->swfw_sync_present = TRUE;
+ /* fall through */
+ case e1000_82571:
+ case e1000_82572:
+ case e1000_82573:
+ hw->eeprom_semaphore_present = TRUE;
+ /* fall through */
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ hw->asf_firmware_present = TRUE;
+ break;
+ default:
+ break;
+ }
+
return E1000_SUCCESS;
}
switch (hw->device_id) {
case E1000_DEV_ID_82545GM_SERDES:
case E1000_DEV_ID_82546GB_SERDES:
+ case E1000_DEV_ID_82571EB_SERDES:
+ case E1000_DEV_ID_82572EI_SERDES:
+ case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
hw->media_type = e1000_media_type_internal_serdes;
break;
default:
- if(hw->mac_type >= e1000_82543) {
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ hw->media_type = e1000_media_type_fiber;
+ break;
+ case e1000_82573:
+ /* The STATUS_TBIMODE bit is reserved or reused for the this
+ * device.
+ */
+ hw->media_type = e1000_media_type_copper;
+ break;
+ default:
status = E1000_READ_REG(hw, STATUS);
- if(status & E1000_STATUS_TBIMODE) {
+ if (status & E1000_STATUS_TBIMODE) {
hw->media_type = e1000_media_type_fiber;
/* tbi_compatibility not valid on fiber */
hw->tbi_compatibility_en = FALSE;
} else {
hw->media_type = e1000_media_type_copper;
}
- } else {
- /* This is an 82542 (fiber only) */
- hw->media_type = e1000_media_type_fiber;
+ break;
}
}
}
uint32_t icr;
uint32_t manc;
uint32_t led_ctrl;
+ uint32_t timeout;
+ uint32_t extcnf_ctrl;
+ int32_t ret_val;
DEBUGFUNC("e1000_reset_hw");
e1000_pci_clear_mwi(hw);
}
+ if(hw->bus_type == e1000_bus_type_pci_express) {
+ /* Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ if(e1000_disable_pciex_master(hw) != E1000_SUCCESS) {
+ DEBUGOUT("PCI-E Master disable polling has failed.\n");
+ }
+ }
+
/* Clear interrupt mask to stop board from generating interrupts */
DEBUGOUT("Masking off all interrupts\n");
E1000_WRITE_REG(hw, IMC, 0xffffffff);
/* Must reset the PHY before resetting the MAC */
if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
- E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_PHY_RST));
+ E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_PHY_RST));
msec_delay(5);
}
+ /* Must acquire the MDIO ownership before MAC reset.
+ * Ownership defaults to firmware after a reset. */
+ if(hw->mac_type == e1000_82573) {
+ timeout = 10;
+
+ extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL);
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+ do {
+ E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl);
+ extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL);
+
+ if(extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
+ break;
+ else
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+ msec_delay(2);
+ timeout--;
+ } while(timeout);
+ }
+
/* Issue a global reset to the MAC. This will reset the chip's
* transmit, receive, DMA, and link units. It will not effect
* the current PCI configuration. The global reset bit is self-
/* Wait for EEPROM reload */
msec_delay(20);
break;
+ case e1000_82573:
+ if (e1000_is_onboard_nvm_eeprom(hw) == FALSE) {
+ udelay(10);
+ ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+ E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH(hw);
+ }
+ /* fall through */
+ case e1000_82571:
+ case e1000_82572:
+ case e1000_80003es2lan:
+ ret_val = e1000_get_auto_rd_done(hw);
+ if(ret_val)
+ /* We don't want to continue accessing MAC registers. */
+ return ret_val;
+ break;
default:
/* Wait for EEPROM reload (it happens automatically) */
msec_delay(5);
}
/* Disable HW ARPs on ASF enabled adapters */
- if(hw->mac_type >= e1000_82540) {
+ if(hw->mac_type >= e1000_82540 && hw->mac_type <= e1000_82547_rev_2) {
manc = E1000_READ_REG(hw, MANC);
manc &= ~(E1000_MANC_ARP_EN);
E1000_WRITE_REG(hw, MANC, manc);
uint16_t pcix_stat_hi_word;
uint16_t cmd_mmrbc;
uint16_t stat_mmrbc;
+ uint32_t mta_size;
+ uint32_t reg_data;
+ uint32_t ctrl_ext;
DEBUGFUNC("e1000_init_hw");
/* Disabling VLAN filtering. */
DEBUGOUT("Initializing the IEEE VLAN\n");
- E1000_WRITE_REG(hw, VET, 0);
-
+ if (hw->mac_type < e1000_82545_rev_3)
+ E1000_WRITE_REG(hw, VET, 0);
e1000_clear_vfta(hw);
/* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
/* Zero out the Multicast HASH table */
DEBUGOUT("Zeroing the MTA\n");
- for(i = 0; i < E1000_MC_TBL_SIZE; i++)
+ mta_size = E1000_MC_TBL_SIZE;
+ for(i = 0; i < mta_size; i++)
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
/* Set the PCI priority bit correctly in the CTRL register. This
* determines if the adapter gives priority to receives, or if it
- * gives equal priority to transmits and receives.
+ * gives equal priority to transmits and receives. Valid only on
+ * 82542 and 82543 silicon.
*/
- if(hw->dma_fairness) {
+ if(hw->dma_fairness && hw->mac_type <= e1000_82543) {
ctrl = E1000_READ_REG(hw, CTRL);
E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR);
}
if(hw->mac_type > e1000_82544) {
ctrl = E1000_READ_REG(hw, TXDCTL);
ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_82571:
+ case e1000_82572:
+ case e1000_82573:
+ case e1000_80003es2lan:
+ ctrl |= E1000_TXDCTL_COUNT_DESC;
+ break;
+ }
E1000_WRITE_REG(hw, TXDCTL, ctrl);
}
+ if (hw->mac_type == e1000_82573) {
+ e1000_enable_tx_pkt_filtering(hw);
+ }
+
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_80003es2lan:
+ /* Enable retransmit on late collisions */
+ reg_data = E1000_READ_REG(hw, TCTL);
+ reg_data |= E1000_TCTL_RTLC;
+ E1000_WRITE_REG(hw, TCTL, reg_data);
+
+ /* Configure Gigabit Carry Extend Padding */
+ reg_data = E1000_READ_REG(hw, TCTL_EXT);
+ reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
+ reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX;
+ E1000_WRITE_REG(hw, TCTL_EXT, reg_data);
+
+ /* Configure Transmit Inter-Packet Gap */
+ reg_data = E1000_READ_REG(hw, TIPG);
+ reg_data &= ~E1000_TIPG_IPGT_MASK;
+ reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
+ E1000_WRITE_REG(hw, TIPG, reg_data);
+
+ reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001);
+ reg_data &= ~0x00100000;
+ E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data);
+ /* Fall through */
+ case e1000_82571:
+ case e1000_82572:
+ ctrl = E1000_READ_REG(hw, TXDCTL1);
+ ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
+ if(hw->mac_type >= e1000_82571)
+ ctrl |= E1000_TXDCTL_COUNT_DESC;
+ E1000_WRITE_REG(hw, TXDCTL1, ctrl);
+ break;
+ }
+
+
+
+ if (hw->mac_type == e1000_82573) {
+ uint32_t gcr = E1000_READ_REG(hw, GCR);
+ gcr |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
+ E1000_WRITE_REG(hw, GCR, gcr);
+ }
+
/* Clear all of the statistics registers (clear on read). It is
* important that we do this after we have tried to establish link
* because the symbol error count will increment wildly if there
*/
e1000_clear_hw_cntrs(hw);
+ if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
+ hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
+ ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ /* Relaxed ordering must be disabled to avoid a parity
+ * error crash in a PCI slot. */
+ ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
+ E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+ }
+
return ret_val;
}
DEBUGFUNC("e1000_setup_link");
+ /* In the case of the phy reset being blocked, we already have a link.
+ * We do not have to set it up again. */
+ if (e1000_check_phy_reset_block(hw))
+ return E1000_SUCCESS;
+
/* Read and store word 0x0F of the EEPROM. This word contains bits
* that determine the hardware's default PAUSE (flow control) mode,
* a bit that determines whether the HW defaults to enabling or
* control setting, then the variable hw->fc will
* be initialized based on a value in the EEPROM.
*/
- if(e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
-
- if(hw->fc == e1000_fc_default) {
- if((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
- hw->fc = e1000_fc_none;
- else if((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
- EEPROM_WORD0F_ASM_DIR)
- hw->fc = e1000_fc_tx_pause;
- else
+ if (hw->fc == e1000_fc_default) {
+ switch (hw->mac_type) {
+ case e1000_82573:
hw->fc = e1000_fc_full;
+ break;
+ default:
+ ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+ 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
+ hw->fc = e1000_fc_none;
+ else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
+ EEPROM_WORD0F_ASM_DIR)
+ hw->fc = e1000_fc_tx_pause;
+ else
+ hw->fc = e1000_fc_full;
+ break;
+ }
}
/* We want to save off the original Flow Control configuration just
* signal detection. So this should be done before e1000_setup_pcs_link()
* or e1000_phy_setup() is called.
*/
- if(hw->mac_type == e1000_82543) {
+ if (hw->mac_type == e1000_82543) {
+ ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+ 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) <<
SWDPIO__EXT_SHIFT);
E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
+
E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time);
/* Set the flow control receive threshold registers. Normally,
DEBUGFUNC("e1000_setup_fiber_serdes_link");
+ /* On 82571 and 82572 Fiber connections, SerDes loopback mode persists
+ * until explicitly turned off or a power cycle is performed. A read to
+ * the register does not indicate its status. Therefore, we ensure
+ * loopback mode is disabled during initialization.
+ */
+ if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572)
+ E1000_WRITE_REG(hw, SCTL, E1000_DISABLE_SERDES_LOOPBACK);
+
/* On adapters with a MAC newer than 82544, SW Defineable pin 1 will be
* set when the optics detect a signal. On older adapters, it will be
* cleared when there is a signal. This applies to fiber media only.
}
/******************************************************************************
-* Detects which PHY is present and the speed and duplex
+* Make sure we have a valid PHY and change PHY mode before link setup.
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
static int32_t
-e1000_setup_copper_link(struct e1000_hw *hw)
+e1000_copper_link_preconfig(struct e1000_hw *hw)
{
uint32_t ctrl;
- uint32_t led_ctrl;
int32_t ret_val;
- uint16_t i;
uint16_t phy_data;
- DEBUGFUNC("e1000_setup_copper_link");
+ DEBUGFUNC("e1000_copper_link_preconfig");
ctrl = E1000_READ_REG(hw, CTRL);
/* With 82543, we need to force speed and duplex on the MAC equal to what
} else {
ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
E1000_WRITE_REG(hw, CTRL, ctrl);
- e1000_phy_hw_reset(hw);
+ ret_val = e1000_phy_hw_reset(hw);
+ if(ret_val)
+ return ret_val;
}
/* Make sure we have a valid PHY */
if(ret_val)
return ret_val;
+ if((hw->mac_type == e1000_82545_rev_3) ||
+ (hw->mac_type == e1000_82546_rev_3)) {
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ phy_data |= 0x00000008;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ }
+
if(hw->mac_type <= e1000_82543 ||
hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2)
hw->phy_reset_disable = FALSE;
- if(!hw->phy_reset_disable) {
- if (hw->phy_type == e1000_phy_igp) {
-
- ret_val = e1000_phy_reset(hw);
- if(ret_val) {
- DEBUGOUT("Error Resetting the PHY\n");
- return ret_val;
- }
-
- /* Wait 10ms for MAC to configure PHY from eeprom settings */
- msec_delay(15);
+ return E1000_SUCCESS;
+}
- /* Configure activity LED after PHY reset */
- led_ctrl = E1000_READ_REG(hw, LEDCTL);
- led_ctrl &= IGP_ACTIVITY_LED_MASK;
- led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
- E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
- /* disable lplu d3 during driver init */
- ret_val = e1000_set_d3_lplu_state(hw, FALSE);
- if(ret_val) {
- DEBUGOUT("Error Disabling LPLU D3\n");
- return ret_val;
- }
+/********************************************************************
+* Copper link setup for e1000_phy_igp series.
+*
+* hw - Struct containing variables accessed by shared code
+*********************************************************************/
+static int32_t
+e1000_copper_link_igp_setup(struct e1000_hw *hw)
+{
+ uint32_t led_ctrl;
+ int32_t ret_val;
+ uint16_t phy_data;
- /* Configure mdi-mdix settings */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL,
- &phy_data);
- if(ret_val)
- return ret_val;
+ DEBUGFUNC("e1000_copper_link_igp_setup");
- if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
- hw->dsp_config_state = e1000_dsp_config_disabled;
- /* Force MDI for IGP B-0 PHY */
- phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX |
- IGP01E1000_PSCR_FORCE_MDI_MDIX);
- hw->mdix = 1;
+ if (hw->phy_reset_disable)
+ return E1000_SUCCESS;
+
+ ret_val = e1000_phy_reset(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
- } else {
- hw->dsp_config_state = e1000_dsp_config_enabled;
- phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
-
- switch (hw->mdix) {
- case 1:
- phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
- break;
- case 2:
- phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
- break;
- case 0:
- default:
- phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
- break;
- }
- }
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL,
- phy_data);
- if(ret_val)
- return ret_val;
+ /* Wait 10ms for MAC to configure PHY from eeprom settings */
+ msec_delay(15);
- /* set auto-master slave resolution settings */
- if(hw->autoneg) {
- e1000_ms_type phy_ms_setting = hw->master_slave;
+ /* Configure activity LED after PHY reset */
+ led_ctrl = E1000_READ_REG(hw, LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
- if(hw->ffe_config_state == e1000_ffe_config_active)
- hw->ffe_config_state = e1000_ffe_config_enabled;
+ /* disable lplu d3 during driver init */
+ ret_val = e1000_set_d3_lplu_state(hw, FALSE);
+ if (ret_val) {
+ DEBUGOUT("Error Disabling LPLU D3\n");
+ return ret_val;
+ }
- if(hw->dsp_config_state == e1000_dsp_config_activated)
- hw->dsp_config_state = e1000_dsp_config_enabled;
+ /* disable lplu d0 during driver init */
+ ret_val = e1000_set_d0_lplu_state(hw, FALSE);
+ if (ret_val) {
+ DEBUGOUT("Error Disabling LPLU D0\n");
+ return ret_val;
+ }
+ /* Configure mdi-mdix settings */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
- /* when autonegotiation advertisment is only 1000Mbps then we
- * should disable SmartSpeed and enable Auto MasterSlave
- * resolution as hardware default. */
- if(hw->autoneg_advertised == ADVERTISE_1000_FULL) {
- /* Disable SmartSpeed */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- &phy_data);
- if(ret_val)
- return ret_val;
- phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw,
- IGP01E1000_PHY_PORT_CONFIG,
- phy_data);
- if(ret_val)
- return ret_val;
- /* Set auto Master/Slave resolution process */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
- if(ret_val)
- return ret_val;
- phy_data &= ~CR_1000T_MS_ENABLE;
- ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
- if(ret_val)
- return ret_val;
- }
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ hw->dsp_config_state = e1000_dsp_config_disabled;
+ /* Force MDI for earlier revs of the IGP PHY */
+ phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX | IGP01E1000_PSCR_FORCE_MDI_MDIX);
+ hw->mdix = 1;
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
- if(ret_val)
- return ret_val;
+ } else {
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
- /* load defaults for future use */
- hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
- ((phy_data & CR_1000T_MS_VALUE) ?
- e1000_ms_force_master :
- e1000_ms_force_slave) :
- e1000_ms_auto;
-
- switch (phy_ms_setting) {
- case e1000_ms_force_master:
- phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
- break;
- case e1000_ms_force_slave:
- phy_data |= CR_1000T_MS_ENABLE;
- phy_data &= ~(CR_1000T_MS_VALUE);
- break;
- case e1000_ms_auto:
- phy_data &= ~CR_1000T_MS_ENABLE;
- default:
- break;
- }
- ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
- if(ret_val)
- return ret_val;
- }
- } else {
- /* Enable CRS on TX. This must be set for half-duplex operation. */
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
- &phy_data);
- if(ret_val)
- return ret_val;
+ switch (hw->mdix) {
+ case 1:
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 2:
+ phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 0:
+ default:
+ phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
+ break;
+ }
+ }
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
- phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+ /* set auto-master slave resolution settings */
+ if(hw->autoneg) {
+ e1000_ms_type phy_ms_setting = hw->master_slave;
- /* Options:
- * MDI/MDI-X = 0 (default)
- * 0 - Auto for all speeds
- * 1 - MDI mode
- * 2 - MDI-X mode
- * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
- */
- phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+ if(hw->ffe_config_state == e1000_ffe_config_active)
+ hw->ffe_config_state = e1000_ffe_config_enabled;
- switch (hw->mdix) {
- case 1:
- phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
- break;
- case 2:
- phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
- break;
- case 3:
- phy_data |= M88E1000_PSCR_AUTO_X_1000T;
- break;
- case 0:
- default:
- phy_data |= M88E1000_PSCR_AUTO_X_MODE;
- break;
- }
+ if(hw->dsp_config_state == e1000_dsp_config_activated)
+ hw->dsp_config_state = e1000_dsp_config_enabled;
- /* Options:
- * disable_polarity_correction = 0 (default)
- * Automatic Correction for Reversed Cable Polarity
- * 0 - Disabled
- * 1 - Enabled
- */
- phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
- if(hw->disable_polarity_correction == 1)
- phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
- phy_data);
+ /* when autonegotiation advertisment is only 1000Mbps then we
+ * should disable SmartSpeed and enable Auto MasterSlave
+ * resolution as hardware default. */
+ if(hw->autoneg_advertised == ADVERTISE_1000_FULL) {
+ /* Disable SmartSpeed */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
if(ret_val)
return ret_val;
-
- /* Force TX_CLK in the Extended PHY Specific Control Register
- * to 25MHz clock.
- */
- ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
- &phy_data);
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
if(ret_val)
return ret_val;
-
- phy_data |= M88E1000_EPSCR_TX_CLK_25;
-
- if (hw->phy_revision < M88E1011_I_REV_4) {
- /* Configure Master and Slave downshift values */
- phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
- M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
- phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
- M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
- ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
- phy_data);
- if(ret_val)
- return ret_val;
- }
-
- /* SW Reset the PHY so all changes take effect */
- ret_val = e1000_phy_reset(hw);
- if(ret_val) {
- DEBUGOUT("Error Resetting the PHY\n");
- return ret_val;
- }
- }
-
- /* Options:
- * autoneg = 1 (default)
- * PHY will advertise value(s) parsed from
- * autoneg_advertised and fc
- * autoneg = 0
- * PHY will be set to 10H, 10F, 100H, or 100F
- * depending on value parsed from forced_speed_duplex.
- */
-
- /* Is autoneg enabled? This is enabled by default or by software
- * override. If so, call e1000_phy_setup_autoneg routine to parse the
- * autoneg_advertised and fc options. If autoneg is NOT enabled, then
- * the user should have provided a speed/duplex override. If so, then
- * call e1000_phy_force_speed_duplex to parse and set this up.
- */
- if(hw->autoneg) {
- /* Perform some bounds checking on the hw->autoneg_advertised
- * parameter. If this variable is zero, then set it to the default.
- */
- hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;
-
- /* If autoneg_advertised is zero, we assume it was not defaulted
- * by the calling code so we set to advertise full capability.
- */
- if(hw->autoneg_advertised == 0)
- hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
-
- DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
- ret_val = e1000_phy_setup_autoneg(hw);
- if(ret_val) {
- DEBUGOUT("Error Setting up Auto-Negotiation\n");
- return ret_val;
- }
- DEBUGOUT("Restarting Auto-Neg\n");
-
- /* Restart auto-negotiation by setting the Auto Neg Enable bit and
- * the Auto Neg Restart bit in the PHY control register.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ /* Set auto Master/Slave resolution process */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
if(ret_val)
return ret_val;
-
- phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
- ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ phy_data &= ~CR_1000T_MS_ENABLE;
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
if(ret_val)
return ret_val;
-
- /* Does the user want to wait for Auto-Neg to complete here, or
- * check at a later time (for example, callback routine).
- */
- if(hw->wait_autoneg_complete) {
- ret_val = e1000_wait_autoneg(hw);
- if(ret_val) {
- DEBUGOUT("Error while waiting for autoneg to complete\n");
- return ret_val;
- }
- }
- hw->get_link_status = TRUE;
- } else {
- DEBUGOUT("Forcing speed and duplex\n");
- ret_val = e1000_phy_force_speed_duplex(hw);
- if(ret_val) {
- DEBUGOUT("Error Forcing Speed and Duplex\n");
- return ret_val;
- }
}
- } /* !hw->phy_reset_disable */
- /* Check link status. Wait up to 100 microseconds for link to become
- * valid.
- */
- for(i = 0; i < 10; i++) {
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
if(ret_val)
return ret_val;
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+
+ /* load defaults for future use */
+ hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
+ ((phy_data & CR_1000T_MS_VALUE) ?
+ e1000_ms_force_master :
+ e1000_ms_force_slave) :
+ e1000_ms_auto;
+
+ switch (phy_ms_setting) {
+ case e1000_ms_force_master:
+ phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_force_slave:
+ phy_data |= CR_1000T_MS_ENABLE;
+ phy_data &= ~(CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_auto:
+ phy_data &= ~CR_1000T_MS_ENABLE;
+ default:
+ break;
+ }
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
if(ret_val)
return ret_val;
+ }
- if(phy_data & MII_SR_LINK_STATUS) {
- /* We have link, so we need to finish the config process:
- * 1) Set up the MAC to the current PHY speed/duplex
- * if we are on 82543. If we
- * are on newer silicon, we only need to configure
- * collision distance in the Transmit Control Register.
- * 2) Set up flow control on the MAC to that established with
- * the link partner.
- */
- if(hw->mac_type >= e1000_82544) {
- e1000_config_collision_dist(hw);
- } else {
- ret_val = e1000_config_mac_to_phy(hw);
- if(ret_val) {
- DEBUGOUT("Error configuring MAC to PHY settings\n");
- return ret_val;
- }
- }
- ret_val = e1000_config_fc_after_link_up(hw);
- if(ret_val) {
- DEBUGOUT("Error Configuring Flow Control\n");
- return ret_val;
- }
- DEBUGOUT("Valid link established!!!\n");
-
- if(hw->phy_type == e1000_phy_igp) {
- ret_val = e1000_config_dsp_after_link_change(hw, TRUE);
- if(ret_val) {
- DEBUGOUT("Error Configuring DSP after link up\n");
- return ret_val;
- }
- }
- DEBUGOUT("Valid link established!!!\n");
- return E1000_SUCCESS;
- }
- udelay(10);
- }
-
- DEBUGOUT("Unable to establish link!!!\n");
return E1000_SUCCESS;
}
-/******************************************************************************
-* Configures PHY autoneg and flow control advertisement settings
+/********************************************************************
+* Copper link setup for e1000_phy_gg82563 series.
*
* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-int32_t
-e1000_phy_setup_autoneg(struct e1000_hw *hw)
+*********************************************************************/
+static int32_t
+e1000_copper_link_ggp_setup(struct e1000_hw *hw)
{
int32_t ret_val;
- uint16_t mii_autoneg_adv_reg;
- uint16_t mii_1000t_ctrl_reg;
+ uint16_t phy_data;
+ uint32_t reg_data;
- DEBUGFUNC("e1000_phy_setup_autoneg");
+ DEBUGFUNC("e1000_copper_link_ggp_setup");
- /* Read the MII Auto-Neg Advertisement Register (Address 4). */
- ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
- if(ret_val)
- return ret_val;
+ if(!hw->phy_reset_disable) {
+
+ /* Enable CRS on TX for half-duplex operation. */
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
- /* Read the MII 1000Base-T Control Register (Address 9). */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
- if(ret_val)
- return ret_val;
+ phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
+ /* Use 25MHz for both link down and 1000BASE-T for Tx clock */
+ phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ;
- /* Need to parse both autoneg_advertised and fc and set up
- * the appropriate PHY registers. First we will parse for
- * autoneg_advertised software override. Since we can advertise
- * a plethora of combinations, we need to check each bit
- * individually.
- */
+ ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL,
+ phy_data);
+ if(ret_val)
+ return ret_val;
- /* First we clear all the 10/100 mb speed bits in the Auto-Neg
- * Advertisement Register (Address 4) and the 1000 mb speed bits in
- * the 1000Base-T Control Register (Address 9).
- */
- mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
- mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
+ /* Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
- DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
+ phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;
- /* Do we want to advertise 10 Mb Half Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_10_HALF) {
- DEBUGOUT("Advertise 10mb Half duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
- }
+ switch (hw->mdix) {
+ case 1:
+ phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
+ break;
+ case 2:
+ phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
+ break;
+ case 0:
+ default:
+ phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
+ break;
+ }
- /* Do we want to advertise 10 Mb Full Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_10_FULL) {
- DEBUGOUT("Advertise 10mb Full duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
- }
+ /* Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
+ if(hw->disable_polarity_correction == 1)
+ phy_data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
+ ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL, phy_data);
- /* Do we want to advertise 100 Mb Half Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_100_HALF) {
- DEBUGOUT("Advertise 100mb Half duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
- }
+ if(ret_val)
+ return ret_val;
- /* Do we want to advertise 100 Mb Full Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_100_FULL) {
- DEBUGOUT("Advertise 100mb Full duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
- }
+ /* SW Reset the PHY so all changes take effect */
+ ret_val = e1000_phy_reset(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
+ } /* phy_reset_disable */
+
+ if (hw->mac_type == e1000_80003es2lan) {
+ /* Bypass RX and TX FIFO's */
+ ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL,
+ E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS |
+ E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS);
+ if (ret_val)
+ return ret_val;
- /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
- if(hw->autoneg_advertised & ADVERTISE_1000_HALF) {
- DEBUGOUT("Advertise 1000mb Half duplex requested, request denied!\n");
- }
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, &phy_data);
+ if (ret_val)
+ return ret_val;
- /* Do we want to advertise 1000 Mb Full Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_1000_FULL) {
- DEBUGOUT("Advertise 1000mb Full duplex\n");
- mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
- }
+ phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
+ ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, phy_data);
- /* Check for a software override of the flow control settings, and
- * setup the PHY advertisement registers accordingly. If
- * auto-negotiation is enabled, then software will have to set the
- * "PAUSE" bits to the correct value in the Auto-Negotiation
- * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
- *
- * The possible values of the "fc" parameter are:
- * 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause frames
- * but not send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames
- * but we do not support receiving pause frames).
- * 3: Both Rx and TX flow control (symmetric) are enabled.
- * other: No software override. The flow control configuration
- * in the EEPROM is used.
- */
- switch (hw->fc) {
- case e1000_fc_none: /* 0 */
- /* Flow control (RX & TX) is completely disabled by a
- * software over-ride.
- */
- mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
- break;
- case e1000_fc_rx_pause: /* 1 */
- /* RX Flow control is enabled, and TX Flow control is
- * disabled, by a software over-ride.
+ if (ret_val)
+ return ret_val;
+
+ reg_data = E1000_READ_REG(hw, CTRL_EXT);
+ reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK);
+ E1000_WRITE_REG(hw, CTRL_EXT, reg_data);
+
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Do not init these registers when the HW is in IAMT mode, since the
+ * firmware will have already initialized them. We only initialize
+ * them if the HW is not in IAMT mode.
*/
- /* Since there really isn't a way to advertise that we are
- * capable of RX Pause ONLY, we will advertise that we
- * support both symmetric and asymmetric RX PAUSE. Later
- * (in e1000_config_fc_after_link_up) we will disable the
- *hw's ability to send PAUSE frames.
+ if (e1000_check_mng_mode(hw) == FALSE) {
+ /* Enable Electrical Idle on the PHY */
+ phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
+ ret_val = e1000_write_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Enable Pass False Carrier on the PHY */
+ phy_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
+
+ ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Workaround: Disable padding in Kumeran interface in the MAC
+ * and in the PHY to avoid CRC errors.
*/
- mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_INBAND_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_data |= GG82563_ICR_DIS_PADDING;
+ ret_val = e1000_write_phy_reg(hw, GG82563_PHY_INBAND_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/********************************************************************
+* Copper link setup for e1000_phy_m88 series.
+*
+* hw - Struct containing variables accessed by shared code
+*********************************************************************/
+static int32_t
+e1000_copper_link_mgp_setup(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ DEBUGFUNC("e1000_copper_link_mgp_setup");
+
+ if(hw->phy_reset_disable)
+ return E1000_SUCCESS;
+
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+
+ /* Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+
+ switch (hw->mdix) {
+ case 1:
+ phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
break;
- case e1000_fc_tx_pause: /* 2 */
- /* TX Flow control is enabled, and RX Flow control is
- * disabled, by a software over-ride.
- */
- mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
- mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+ case 2:
+ phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
break;
- case e1000_fc_full: /* 3 */
- /* Flow control (both RX and TX) is enabled by a software
- * over-ride.
- */
- mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ case 3:
+ phy_data |= M88E1000_PSCR_AUTO_X_1000T;
break;
+ case 0:
default:
- DEBUGOUT("Flow control param set incorrectly\n");
- return -E1000_ERR_CONFIG;
+ phy_data |= M88E1000_PSCR_AUTO_X_MODE;
+ break;
}
- ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+ /* Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
+ if(hw->disable_polarity_correction == 1)
+ phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
+
+ /* Force TX_CLK in the Extended PHY Specific Control Register
+ * to 25MHz clock.
+ */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
if(ret_val)
return ret_val;
- DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
- ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
- if(ret_val)
+ if (hw->phy_revision < M88E1011_I_REV_4) {
+ /* Configure Master and Slave downshift values */
+ phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
+ phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
+ }
+
+ /* SW Reset the PHY so all changes take effect */
+ ret_val = e1000_phy_reset(hw);
+ if(ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
return ret_val;
+ }
- return E1000_SUCCESS;
+ return E1000_SUCCESS;
}
-/******************************************************************************
-* Force PHY speed and duplex settings to hw->forced_speed_duplex
+/********************************************************************
+* Setup auto-negotiation and flow control advertisements,
+* and then perform auto-negotiation.
*
* hw - Struct containing variables accessed by shared code
-******************************************************************************/
+*********************************************************************/
static int32_t
-e1000_phy_force_speed_duplex(struct e1000_hw *hw)
+e1000_copper_link_autoneg(struct e1000_hw *hw)
{
- uint32_t ctrl;
int32_t ret_val;
- uint16_t mii_ctrl_reg;
- uint16_t mii_status_reg;
uint16_t phy_data;
- uint16_t i;
- DEBUGFUNC("e1000_phy_force_speed_duplex");
-
- /* Turn off Flow control if we are forcing speed and duplex. */
- hw->fc = e1000_fc_none;
+ DEBUGFUNC("e1000_copper_link_autoneg");
- DEBUGOUT1("hw->fc = %d\n", hw->fc);
+ /* Perform some bounds checking on the hw->autoneg_advertised
+ * parameter. If this variable is zero, then set it to the default.
+ */
+ hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;
- /* Read the Device Control Register. */
- ctrl = E1000_READ_REG(hw, CTRL);
+ /* If autoneg_advertised is zero, we assume it was not defaulted
+ * by the calling code so we set to advertise full capability.
+ */
+ if(hw->autoneg_advertised == 0)
+ hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
- /* Set the bits to Force Speed and Duplex in the Device Ctrl Reg. */
- ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
- ctrl &= ~(DEVICE_SPEED_MASK);
+ DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
+ ret_val = e1000_phy_setup_autoneg(hw);
+ if(ret_val) {
+ DEBUGOUT("Error Setting up Auto-Negotiation\n");
+ return ret_val;
+ }
+ DEBUGOUT("Restarting Auto-Neg\n");
- /* Clear the Auto Speed Detect Enable bit. */
- ctrl &= ~E1000_CTRL_ASDE;
+ /* Restart auto-negotiation by setting the Auto Neg Enable bit and
+ * the Auto Neg Restart bit in the PHY control register.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
- /* Read the MII Control Register. */
- ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg);
+ phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
if(ret_val)
return ret_val;
- /* We need to disable autoneg in order to force link and duplex. */
+ /* Does the user want to wait for Auto-Neg to complete here, or
+ * check at a later time (for example, callback routine).
+ */
+ if(hw->wait_autoneg_complete) {
+ ret_val = e1000_wait_autoneg(hw);
+ if(ret_val) {
+ DEBUGOUT("Error while waiting for autoneg to complete\n");
+ return ret_val;
+ }
+ }
- mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN;
+ hw->get_link_status = TRUE;
- /* Are we forcing Full or Half Duplex? */
- if(hw->forced_speed_duplex == e1000_100_full ||
- hw->forced_speed_duplex == e1000_10_full) {
- /* We want to force full duplex so we SET the full duplex bits in the
- * Device and MII Control Registers.
- */
- ctrl |= E1000_CTRL_FD;
- mii_ctrl_reg |= MII_CR_FULL_DUPLEX;
- DEBUGOUT("Full Duplex\n");
+ return E1000_SUCCESS;
+}
+
+
+/******************************************************************************
+* Config the MAC and the PHY after link is up.
+* 1) Set up the MAC to the current PHY speed/duplex
+* if we are on 82543. If we
+* are on newer silicon, we only need to configure
+* collision distance in the Transmit Control Register.
+* 2) Set up flow control on the MAC to that established with
+* the link partner.
+* 3) Config DSP to improve Gigabit link quality for some PHY revisions.
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int32_t
+e1000_copper_link_postconfig(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ DEBUGFUNC("e1000_copper_link_postconfig");
+
+ if(hw->mac_type >= e1000_82544) {
+ e1000_config_collision_dist(hw);
} else {
- /* We want to force half duplex so we CLEAR the full duplex bits in
- * the Device and MII Control Registers.
- */
- ctrl &= ~E1000_CTRL_FD;
- mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX;
- DEBUGOUT("Half Duplex\n");
+ ret_val = e1000_config_mac_to_phy(hw);
+ if(ret_val) {
+ DEBUGOUT("Error configuring MAC to PHY settings\n");
+ return ret_val;
+ }
+ }
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if(ret_val) {
+ DEBUGOUT("Error Configuring Flow Control\n");
+ return ret_val;
}
- /* Are we forcing 100Mbps??? */
- if(hw->forced_speed_duplex == e1000_100_full ||
- hw->forced_speed_duplex == e1000_100_half) {
- /* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */
- ctrl |= E1000_CTRL_SPD_100;
- mii_ctrl_reg |= MII_CR_SPEED_100;
- mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
- DEBUGOUT("Forcing 100mb ");
- } else {
- /* Set the 10Mb bit and turn off the 1000Mb and 100Mb bits. */
- ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
- mii_ctrl_reg |= MII_CR_SPEED_10;
- mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
- DEBUGOUT("Forcing 10mb ");
+ /* Config DSP to improve Giga link quality */
+ if(hw->phy_type == e1000_phy_igp) {
+ ret_val = e1000_config_dsp_after_link_change(hw, TRUE);
+ if(ret_val) {
+ DEBUGOUT("Error Configuring DSP after link up\n");
+ return ret_val;
+ }
}
+
+ return E1000_SUCCESS;
+}
- e1000_config_collision_dist(hw);
+/******************************************************************************
+* Detects which PHY is present and setup the speed and duplex
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int32_t
+e1000_setup_copper_link(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t i;
+ uint16_t phy_data;
+ uint16_t reg_data;
- /* Write the configured values back to the Device Control Reg. */
- E1000_WRITE_REG(hw, CTRL, ctrl);
+ DEBUGFUNC("e1000_setup_copper_link");
- if (hw->phy_type == e1000_phy_m88) {
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
- if(ret_val)
+ /* Check if it is a valid PHY and set PHY mode if necessary. */
+ ret_val = e1000_copper_link_preconfig(hw);
+ if(ret_val)
+ return ret_val;
+
+ switch (hw->mac_type) {
+ case e1000_80003es2lan:
+ ret_val = e1000_read_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL,
+ ®_data);
+ if (ret_val)
return ret_val;
+ reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING;
+ ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL,
+ reg_data);
+ if (ret_val)
+ return ret_val;
+ break;
+ default:
+ break;
+ }
- /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
- * forced whenever speed are duplex are forced.
- */
- phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2) {
+ ret_val = e1000_copper_link_igp_setup(hw);
if(ret_val)
return ret_val;
-
- DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data);
-
- /* Need to reset the PHY or these changes will be ignored */
- mii_ctrl_reg |= MII_CR_RESET;
- } else {
- /* Clear Auto-Crossover to force MDI manually. IGP requires MDI
- * forced whenever speed or duplex are forced.
- */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ } else if (hw->phy_type == e1000_phy_m88) {
+ ret_val = e1000_copper_link_mgp_setup(hw);
if(ret_val)
return ret_val;
-
- phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
- phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
-
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ } else if (hw->phy_type == e1000_phy_gg82563) {
+ ret_val = e1000_copper_link_ggp_setup(hw);
if(ret_val)
return ret_val;
}
- /* Write back the modified PHY MII control register. */
- ret_val = e1000_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg);
- if(ret_val)
- return ret_val;
-
- udelay(1);
-
- /* The wait_autoneg_complete flag may be a little misleading here.
- * Since we are forcing speed and duplex, Auto-Neg is not enabled.
- * But we do want to delay for a period while forcing only so we
- * don't generate false No Link messages. So we will wait here
- * only if the user has set wait_autoneg_complete to 1, which is
- * the default.
- */
- if(hw->wait_autoneg_complete) {
- /* We will wait for autoneg to complete. */
- DEBUGOUT("Waiting for forced speed/duplex link.\n");
- mii_status_reg = 0;
-
- /* We will wait for autoneg to complete or 4.5 seconds to expire. */
- for(i = PHY_FORCE_TIME; i > 0; i--) {
- /* Read the MII Status Register and wait for Auto-Neg Complete bit
- * to be set.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
- return ret_val;
-
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
- return ret_val;
-
- if(mii_status_reg & MII_SR_LINK_STATUS) break;
- msec_delay(100);
- }
- if((i == 0) && (hw->phy_type == e1000_phy_m88)) {
- /* We didn't get link. Reset the DSP and wait again for link. */
- ret_val = e1000_phy_reset_dsp(hw);
- if(ret_val) {
- DEBUGOUT("Error Resetting PHY DSP\n");
- return ret_val;
- }
- }
- /* This loop will early-out if the link condition has been met. */
- for(i = PHY_FORCE_TIME; i > 0; i--) {
- if(mii_status_reg & MII_SR_LINK_STATUS) break;
- msec_delay(100);
- /* Read the MII Status Register and wait for Auto-Neg Complete bit
- * to be set.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
- return ret_val;
-
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
- return ret_val;
- }
- }
-
- if (hw->phy_type == e1000_phy_m88) {
- /* Because we reset the PHY above, we need to re-force TX_CLK in the
- * Extended PHY Specific Control Register to 25MHz clock. This value
- * defaults back to a 2.5MHz clock when the PHY is reset.
- */
- ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
+ if(hw->autoneg) {
+ /* Setup autoneg and flow control advertisement
+ * and perform autonegotiation */
+ ret_val = e1000_copper_link_autoneg(hw);
if(ret_val)
+ return ret_val;
+ } else {
+ /* PHY will be set to 10H, 10F, 100H,or 100F
+ * depending on value from forced_speed_duplex. */
+ DEBUGOUT("Forcing speed and duplex\n");
+ ret_val = e1000_phy_force_speed_duplex(hw);
+ if(ret_val) {
+ DEBUGOUT("Error Forcing Speed and Duplex\n");
return ret_val;
+ }
+ }
- phy_data |= M88E1000_EPSCR_TX_CLK_25;
- ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
+ /* Check link status. Wait up to 100 microseconds for link to become
+ * valid.
+ */
+ for(i = 0; i < 10; i++) {
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
if(ret_val)
return ret_val;
-
- /* In addition, because of the s/w reset above, we need to enable CRS on
- * TX. This must be set for both full and half duplex operation.
- */
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
if(ret_val)
return ret_val;
- phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
- if(ret_val)
- return ret_val;
+ if(phy_data & MII_SR_LINK_STATUS) {
+ /* Config the MAC and PHY after link is up */
+ ret_val = e1000_copper_link_postconfig(hw);
+ if(ret_val)
+ return ret_val;
+
+ DEBUGOUT("Valid link established!!!\n");
+ return E1000_SUCCESS;
+ }
+ udelay(10);
}
+
+ DEBUGOUT("Unable to establish link!!!\n");
return E1000_SUCCESS;
}
/******************************************************************************
-* Sets the collision distance in the Transmit Control register
+* Configure the MAC-to-PHY interface for 10/100Mbps
*
* hw - Struct containing variables accessed by shared code
-*
-* Link should have been established previously. Reads the speed and duplex
-* information from the Device Status register.
******************************************************************************/
-void
-e1000_config_collision_dist(struct e1000_hw *hw)
+static int32_t
+e1000_configure_kmrn_for_10_100(struct e1000_hw *hw)
{
- uint32_t tctl;
+ int32_t ret_val = E1000_SUCCESS;
+ uint32_t tipg;
+ uint16_t reg_data;
- DEBUGFUNC("e1000_config_collision_dist");
+ DEBUGFUNC("e1000_configure_kmrn_for_10_100");
- tctl = E1000_READ_REG(hw, TCTL);
+ reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT;
+ ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
+ if (ret_val)
+ return ret_val;
- tctl &= ~E1000_TCTL_COLD;
- tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT;
+ /* Configure Transmit Inter-Packet Gap */
+ tipg = E1000_READ_REG(hw, TIPG);
+ tipg &= ~E1000_TIPG_IPGT_MASK;
+ tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100;
+ E1000_WRITE_REG(hw, TIPG, tipg);
- E1000_WRITE_REG(hw, TCTL, tctl);
- E1000_WRITE_FLUSH(hw);
+ return ret_val;
+}
+
+static int32_t
+e1000_configure_kmrn_for_1000(struct e1000_hw *hw)
+{
+ int32_t ret_val = E1000_SUCCESS;
+ uint16_t reg_data;
+ uint32_t tipg;
+
+ DEBUGFUNC("e1000_configure_kmrn_for_1000");
+
+ reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT;
+ ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Configure Transmit Inter-Packet Gap */
+ tipg = E1000_READ_REG(hw, TIPG);
+ tipg &= ~E1000_TIPG_IPGT_MASK;
+ tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
+ E1000_WRITE_REG(hw, TIPG, tipg);
+
+ return ret_val;
}
/******************************************************************************
-* Sets MAC speed and duplex settings to reflect the those in the PHY
+* Configures PHY autoneg and flow control advertisement settings
*
* hw - Struct containing variables accessed by shared code
-* mii_reg - data to write to the MII control register
-*
-* The contents of the PHY register containing the needed information need to
-* be passed in.
******************************************************************************/
-static int32_t
-e1000_config_mac_to_phy(struct e1000_hw *hw)
+int32_t
+e1000_phy_setup_autoneg(struct e1000_hw *hw)
{
- uint32_t ctrl;
int32_t ret_val;
- uint16_t phy_data;
+ uint16_t mii_autoneg_adv_reg;
+ uint16_t mii_1000t_ctrl_reg;
- DEBUGFUNC("e1000_config_mac_to_phy");
+ DEBUGFUNC("e1000_phy_setup_autoneg");
- /* Read the Device Control Register and set the bits to Force Speed
- * and Duplex.
- */
- ctrl = E1000_READ_REG(hw, CTRL);
- ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
- ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS);
+ /* Read the MII Auto-Neg Advertisement Register (Address 4). */
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+ if(ret_val)
+ return ret_val;
- /* Set up duplex in the Device Control and Transmit Control
- * registers depending on negotiated values.
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+ if(ret_val)
+ return ret_val;
+
+ /* Need to parse both autoneg_advertised and fc and set up
+ * the appropriate PHY registers. First we will parse for
+ * autoneg_advertised software override. Since we can advertise
+ * a plethora of combinations, we need to check each bit
+ * individually.
*/
- if (hw->phy_type == e1000_phy_igp) {
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
- &phy_data);
- if(ret_val)
- return ret_val;
- if(phy_data & IGP01E1000_PSSR_FULL_DUPLEX) ctrl |= E1000_CTRL_FD;
- else ctrl &= ~E1000_CTRL_FD;
-
- e1000_config_collision_dist(hw);
+ /* First we clear all the 10/100 mb speed bits in the Auto-Neg
+ * Advertisement Register (Address 4) and the 1000 mb speed bits in
+ * the 1000Base-T Control Register (Address 9).
+ */
+ mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
+ mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
- /* Set up speed in the Device Control register depending on
- * negotiated values.
- */
- if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
- IGP01E1000_PSSR_SPEED_1000MBPS)
- ctrl |= E1000_CTRL_SPD_1000;
- else if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
- IGP01E1000_PSSR_SPEED_100MBPS)
- ctrl |= E1000_CTRL_SPD_100;
- } else {
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
- &phy_data);
- if(ret_val)
- return ret_val;
+ DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
- if(phy_data & M88E1000_PSSR_DPLX) ctrl |= E1000_CTRL_FD;
- else ctrl &= ~E1000_CTRL_FD;
+ /* Do we want to advertise 10 Mb Half Duplex? */
+ if(hw->autoneg_advertised & ADVERTISE_10_HALF) {
+ DEBUGOUT("Advertise 10mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+ }
- e1000_config_collision_dist(hw);
+ /* Do we want to advertise 10 Mb Full Duplex? */
+ if(hw->autoneg_advertised & ADVERTISE_10_FULL) {
+ DEBUGOUT("Advertise 10mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+ }
- /* Set up speed in the Device Control register depending on
- * negotiated values.
- */
- if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
- ctrl |= E1000_CTRL_SPD_1000;
- else if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
- ctrl |= E1000_CTRL_SPD_100;
+ /* Do we want to advertise 100 Mb Half Duplex? */
+ if(hw->autoneg_advertised & ADVERTISE_100_HALF) {
+ DEBUGOUT("Advertise 100mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
}
- /* Write the configured values back to the Device Control Reg. */
- E1000_WRITE_REG(hw, CTRL, ctrl);
- return E1000_SUCCESS;
-}
-/******************************************************************************
- * Forces the MAC's flow control settings.
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Sets the TFCE and RFCE bits in the device control register to reflect
- * the adapter settings. TFCE and RFCE need to be explicitly set by
- * software when a Copper PHY is used because autonegotiation is managed
- * by the PHY rather than the MAC. Software must also configure these
- * bits when link is forced on a fiber connection.
- *****************************************************************************/
-int32_t
-e1000_force_mac_fc(struct e1000_hw *hw)
-{
- uint32_t ctrl;
+ /* Do we want to advertise 100 Mb Full Duplex? */
+ if(hw->autoneg_advertised & ADVERTISE_100_FULL) {
+ DEBUGOUT("Advertise 100mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+ }
- DEBUGFUNC("e1000_force_mac_fc");
+ /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
+ if(hw->autoneg_advertised & ADVERTISE_1000_HALF) {
+ DEBUGOUT("Advertise 1000mb Half duplex requested, request denied!\n");
+ }
- /* Get the current configuration of the Device Control Register */
- ctrl = E1000_READ_REG(hw, CTRL);
+ /* Do we want to advertise 1000 Mb Full Duplex? */
+ if(hw->autoneg_advertised & ADVERTISE_1000_FULL) {
+ DEBUGOUT("Advertise 1000mb Full duplex\n");
+ mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+ }
- /* Because we didn't get link via the internal auto-negotiation
- * mechanism (we either forced link or we got link via PHY
- * auto-neg), we have to manually enable/disable transmit an
- * receive flow control.
- *
- * The "Case" statement below enables/disable flow control
- * according to the "hw->fc" parameter.
+ /* Check for a software override of the flow control settings, and
+ * setup the PHY advertisement registers accordingly. If
+ * auto-negotiation is enabled, then software will have to set the
+ * "PAUSE" bits to the correct value in the Auto-Negotiation
+ * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
*
* The possible values of the "fc" parameter are:
* 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause
- * frames but not send pause frames).
+ * 1: Rx flow control is enabled (we can receive pause frames
+ * but not send pause frames).
* 2: Tx flow control is enabled (we can send pause frames
- * frames but we do not receive pause frames).
- * 3: Both Rx and TX flow control (symmetric) is enabled.
- * other: No other values should be possible at this point.
+ * but we do not support receiving pause frames).
+ * 3: Both Rx and TX flow control (symmetric) are enabled.
+ * other: No software override. The flow control configuration
+ * in the EEPROM is used.
*/
-
switch (hw->fc) {
- case e1000_fc_none:
- ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
+ case e1000_fc_none: /* 0 */
+ /* Flow control (RX & TX) is completely disabled by a
+ * software over-ride.
+ */
+ mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
break;
- case e1000_fc_rx_pause:
- ctrl &= (~E1000_CTRL_TFCE);
- ctrl |= E1000_CTRL_RFCE;
+ case e1000_fc_rx_pause: /* 1 */
+ /* RX Flow control is enabled, and TX Flow control is
+ * disabled, by a software over-ride.
+ */
+ /* Since there really isn't a way to advertise that we are
+ * capable of RX Pause ONLY, we will advertise that we
+ * support both symmetric and asymmetric RX PAUSE. Later
+ * (in e1000_config_fc_after_link_up) we will disable the
+ *hw's ability to send PAUSE frames.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
break;
- case e1000_fc_tx_pause:
- ctrl &= (~E1000_CTRL_RFCE);
- ctrl |= E1000_CTRL_TFCE;
+ case e1000_fc_tx_pause: /* 2 */
+ /* TX Flow control is enabled, and RX Flow control is
+ * disabled, by a software over-ride.
+ */
+ mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
+ mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
break;
- case e1000_fc_full:
- ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
+ case e1000_fc_full: /* 3 */
+ /* Flow control (both RX and TX) is enabled by a software
+ * over-ride.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
break;
default:
DEBUGOUT("Flow control param set incorrectly\n");
return -E1000_ERR_CONFIG;
}
- /* Disable TX Flow Control for 82542 (rev 2.0) */
- if(hw->mac_type == e1000_82542_rev2_0)
- ctrl &= (~E1000_CTRL_TFCE);
+ ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+ if(ret_val)
+ return ret_val;
+
+ DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
+
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+ if(ret_val)
+ return ret_val;
- E1000_WRITE_REG(hw, CTRL, ctrl);
return E1000_SUCCESS;
}
/******************************************************************************
- * Configures flow control settings after link is established
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Should be called immediately after a valid link has been established.
- * Forces MAC flow control settings if link was forced. When in MII/GMII mode
- * and autonegotiation is enabled, the MAC flow control settings will be set
- * based on the flow control negotiated by the PHY. In TBI mode, the TFCE
- * and RFCE bits will be automaticaly set to the negotiated flow control mode.
- *****************************************************************************/
-int32_t
-e1000_config_fc_after_link_up(struct e1000_hw *hw)
+* Force PHY speed and duplex settings to hw->forced_speed_duplex
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int32_t
+e1000_phy_force_speed_duplex(struct e1000_hw *hw)
{
+ uint32_t ctrl;
int32_t ret_val;
+ uint16_t mii_ctrl_reg;
uint16_t mii_status_reg;
- uint16_t mii_nway_adv_reg;
- uint16_t mii_nway_lp_ability_reg;
- uint16_t speed;
- uint16_t duplex;
+ uint16_t phy_data;
+ uint16_t i;
- DEBUGFUNC("e1000_config_fc_after_link_up");
+ DEBUGFUNC("e1000_phy_force_speed_duplex");
- /* Check for the case where we have fiber media and auto-neg failed
- * so we had to force link. In this case, we need to force the
- * configuration of the MAC to match the "fc" parameter.
- */
- if(((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) ||
- ((hw->media_type == e1000_media_type_internal_serdes) && (hw->autoneg_failed)) ||
- ((hw->media_type == e1000_media_type_copper) && (!hw->autoneg))) {
- ret_val = e1000_force_mac_fc(hw);
- if(ret_val) {
- DEBUGOUT("Error forcing flow control settings\n");
- return ret_val;
- }
- }
+ /* Turn off Flow control if we are forcing speed and duplex. */
+ hw->fc = e1000_fc_none;
- /* Check for the case where we have copper media and auto-neg is
- * enabled. In this case, we need to check and see if Auto-Neg
- * has completed, and if so, how the PHY and link partner has
- * flow control configured.
- */
- if((hw->media_type == e1000_media_type_copper) && hw->autoneg) {
- /* Read the MII Status Register and check to see if AutoNeg
- * has completed. We read this twice because this reg has
- * some "sticky" (latched) bits.
+ DEBUGOUT1("hw->fc = %d\n", hw->fc);
+
+ /* Read the Device Control Register. */
+ ctrl = E1000_READ_REG(hw, CTRL);
+
+ /* Set the bits to Force Speed and Duplex in the Device Ctrl Reg. */
+ ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ctrl &= ~(DEVICE_SPEED_MASK);
+
+ /* Clear the Auto Speed Detect Enable bit. */
+ ctrl &= ~E1000_CTRL_ASDE;
+
+ /* Read the MII Control Register. */
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg);
+ if(ret_val)
+ return ret_val;
+
+ /* We need to disable autoneg in order to force link and duplex. */
+
+ mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN;
+
+ /* Are we forcing Full or Half Duplex? */
+ if(hw->forced_speed_duplex == e1000_100_full ||
+ hw->forced_speed_duplex == e1000_10_full) {
+ /* We want to force full duplex so we SET the full duplex bits in the
+ * Device and MII Control Registers.
*/
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ ctrl |= E1000_CTRL_FD;
+ mii_ctrl_reg |= MII_CR_FULL_DUPLEX;
+ DEBUGOUT("Full Duplex\n");
+ } else {
+ /* We want to force half duplex so we CLEAR the full duplex bits in
+ * the Device and MII Control Registers.
+ */
+ ctrl &= ~E1000_CTRL_FD;
+ mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX;
+ DEBUGOUT("Half Duplex\n");
+ }
+
+ /* Are we forcing 100Mbps??? */
+ if(hw->forced_speed_duplex == e1000_100_full ||
+ hw->forced_speed_duplex == e1000_100_half) {
+ /* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */
+ ctrl |= E1000_CTRL_SPD_100;
+ mii_ctrl_reg |= MII_CR_SPEED_100;
+ mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
+ DEBUGOUT("Forcing 100mb ");
+ } else {
+ /* Set the 10Mb bit and turn off the 1000Mb and 100Mb bits. */
+ ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+ mii_ctrl_reg |= MII_CR_SPEED_10;
+ mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
+ DEBUGOUT("Forcing 10mb ");
+ }
+
+ e1000_config_collision_dist(hw);
+
+ /* Write the configured values back to the Device Control Reg. */
+ E1000_WRITE_REG(hw, CTRL, ctrl);
+
+ if ((hw->phy_type == e1000_phy_m88) ||
+ (hw->phy_type == e1000_phy_gg82563)) {
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
if(ret_val)
return ret_val;
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
+
+ /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ * forced whenever speed are duplex are forced.
+ */
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if(ret_val)
return ret_val;
- if(mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
- /* The AutoNeg process has completed, so we now need to
- * read both the Auto Negotiation Advertisement Register
- * (Address 4) and the Auto_Negotiation Base Page Ability
- * Register (Address 5) to determine how flow control was
- * negotiated.
+ DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data);
+
+ /* Need to reset the PHY or these changes will be ignored */
+ mii_ctrl_reg |= MII_CR_RESET;
+ } else {
+ /* Clear Auto-Crossover to force MDI manually. IGP requires MDI
+ * forced whenever speed or duplex are forced.
+ */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
+ }
+
+ /* Write back the modified PHY MII control register. */
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg);
+ if(ret_val)
+ return ret_val;
+
+ udelay(1);
+
+ /* The wait_autoneg_complete flag may be a little misleading here.
+ * Since we are forcing speed and duplex, Auto-Neg is not enabled.
+ * But we do want to delay for a period while forcing only so we
+ * don't generate false No Link messages. So we will wait here
+ * only if the user has set wait_autoneg_complete to 1, which is
+ * the default.
+ */
+ if(hw->wait_autoneg_complete) {
+ /* We will wait for autoneg to complete. */
+ DEBUGOUT("Waiting for forced speed/duplex link.\n");
+ mii_status_reg = 0;
+
+ /* We will wait for autoneg to complete or 4.5 seconds to expire. */
+ for(i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Auto-Neg Complete bit
+ * to be set.
*/
- ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV,
- &mii_nway_adv_reg);
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
if(ret_val)
return ret_val;
- ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY,
- &mii_nway_lp_ability_reg);
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
if(ret_val)
return ret_val;
- /* Two bits in the Auto Negotiation Advertisement Register
- * (Address 4) and two bits in the Auto Negotiation Base
- * Page Ability Register (Address 5) determine flow control
- * for both the PHY and the link partner. The following
- * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
- * 1999, describes these PAUSE resolution bits and how flow
- * control is determined based upon these settings.
- * NOTE: DC = Don't Care
- *
- * LOCAL DEVICE | LINK PARTNER
- * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
- *-------|---------|-------|---------|--------------------
- * 0 | 0 | DC | DC | e1000_fc_none
- * 0 | 1 | 0 | DC | e1000_fc_none
- * 0 | 1 | 1 | 0 | e1000_fc_none
- * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
- * 1 | 0 | 0 | DC | e1000_fc_none
- * 1 | DC | 1 | DC | e1000_fc_full
- * 1 | 1 | 0 | 0 | e1000_fc_none
- * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
- *
- */
- /* Are both PAUSE bits set to 1? If so, this implies
- * Symmetric Flow Control is enabled at both ends. The
- * ASM_DIR bits are irrelevant per the spec.
- *
- * For Symmetric Flow Control:
- *
- * LOCAL DEVICE | LINK PARTNER
- * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
- *-------|---------|-------|---------|--------------------
- * 1 | DC | 1 | DC | e1000_fc_full
- *
- */
- if((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
- /* Now we need to check if the user selected RX ONLY
- * of pause frames. In this case, we had to advertise
- * FULL flow control because we could not advertise RX
- * ONLY. Hence, we must now check to see if we need to
- * turn OFF the TRANSMISSION of PAUSE frames.
- */
- if(hw->original_fc == e1000_fc_full) {
- hw->fc = e1000_fc_full;
- DEBUGOUT("Flow Control = FULL.\r\n");
- } else {
- hw->fc = e1000_fc_rx_pause;
- DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
- }
- }
- /* For receiving PAUSE frames ONLY.
- *
- * LOCAL DEVICE | LINK PARTNER
- * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
- *-------|---------|-------|---------|--------------------
- * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
- *
- */
- else if(!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
- (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
- hw->fc = e1000_fc_tx_pause;
- DEBUGOUT("Flow Control = TX PAUSE frames only.\r\n");
- }
- /* For transmitting PAUSE frames ONLY.
- *
- * LOCAL DEVICE | LINK PARTNER
- * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
- *-------|---------|-------|---------|--------------------
- * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
- *
- */
- else if((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
- (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
- !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
- hw->fc = e1000_fc_rx_pause;
- DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
+ if(mii_status_reg & MII_SR_LINK_STATUS) break;
+ msec_delay(100);
+ }
+ if((i == 0) &&
+ ((hw->phy_type == e1000_phy_m88) ||
+ (hw->phy_type == e1000_phy_gg82563))) {
+ /* We didn't get link. Reset the DSP and wait again for link. */
+ ret_val = e1000_phy_reset_dsp(hw);
+ if(ret_val) {
+ DEBUGOUT("Error Resetting PHY DSP\n");
+ return ret_val;
}
- /* Per the IEEE spec, at this point flow control should be
- * disabled. However, we want to consider that we could
- * be connected to a legacy switch that doesn't advertise
- * desired flow control, but can be forced on the link
- * partner. So if we advertised no flow control, that is
- * what we will resolve to. If we advertised some kind of
- * receive capability (Rx Pause Only or Full Flow Control)
- * and the link partner advertised none, we will configure
- * ourselves to enable Rx Flow Control only. We can do
- * this safely for two reasons: If the link partner really
- * didn't want flow control enabled, and we enable Rx, no
- * harm done since we won't be receiving any PAUSE frames
- * anyway. If the intent on the link partner was to have
- * flow control enabled, then by us enabling RX only, we
- * can at least receive pause frames and process them.
- * This is a good idea because in most cases, since we are
- * predominantly a server NIC, more times than not we will
- * be asked to delay transmission of packets than asking
- * our link partner to pause transmission of frames.
+ }
+ /* This loop will early-out if the link condition has been met. */
+ for(i = PHY_FORCE_TIME; i > 0; i--) {
+ if(mii_status_reg & MII_SR_LINK_STATUS) break;
+ msec_delay(100);
+ /* Read the MII Status Register and wait for Auto-Neg Complete bit
+ * to be set.
*/
- else if((hw->original_fc == e1000_fc_none ||
- hw->original_fc == e1000_fc_tx_pause) ||
- hw->fc_strict_ieee) {
- hw->fc = e1000_fc_none;
- DEBUGOUT("Flow Control = NONE.\r\n");
- } else {
- hw->fc = e1000_fc_rx_pause;
- DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if(ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if(ret_val)
+ return ret_val;
+ }
+ }
+
+ if (hw->phy_type == e1000_phy_m88) {
+ /* Because we reset the PHY above, we need to re-force TX_CLK in the
+ * Extended PHY Specific Control Register to 25MHz clock. This value
+ * defaults back to a 2.5MHz clock when the PHY is reset.
+ */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
+
+ /* In addition, because of the s/w reset above, we need to enable CRS on
+ * TX. This must be set for both full and half duplex operation.
+ */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
+
+ if((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) &&
+ (!hw->autoneg) &&
+ (hw->forced_speed_duplex == e1000_10_full ||
+ hw->forced_speed_duplex == e1000_10_half)) {
+ ret_val = e1000_polarity_reversal_workaround(hw);
+ if(ret_val)
+ return ret_val;
+ }
+ } else if (hw->phy_type == e1000_phy_gg82563) {
+ /* The TX_CLK of the Extended PHY Specific Control Register defaults
+ * to 2.5MHz on a reset. We need to re-force it back to 25MHz, if
+ * we're not in a forced 10/duplex configuration. */
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
+ if ((hw->forced_speed_duplex == e1000_10_full) ||
+ (hw->forced_speed_duplex == e1000_10_half))
+ phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ;
+ else
+ phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25MHZ;
+
+ /* Also due to the reset, we need to enable CRS on Tx. */
+ phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
+
+ ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Sets the collision distance in the Transmit Control register
+*
+* hw - Struct containing variables accessed by shared code
+*
+* Link should have been established previously. Reads the speed and duplex
+* information from the Device Status register.
+******************************************************************************/
+void
+e1000_config_collision_dist(struct e1000_hw *hw)
+{
+ uint32_t tctl, coll_dist;
+
+ DEBUGFUNC("e1000_config_collision_dist");
+
+ if (hw->mac_type < e1000_82543)
+ coll_dist = E1000_COLLISION_DISTANCE_82542;
+ else
+ coll_dist = E1000_COLLISION_DISTANCE;
+
+ tctl = E1000_READ_REG(hw, TCTL);
+
+ tctl &= ~E1000_TCTL_COLD;
+ tctl |= coll_dist << E1000_COLD_SHIFT;
+
+ E1000_WRITE_REG(hw, TCTL, tctl);
+ E1000_WRITE_FLUSH(hw);
+}
+
+/******************************************************************************
+* Sets MAC speed and duplex settings to reflect the those in the PHY
+*
+* hw - Struct containing variables accessed by shared code
+* mii_reg - data to write to the MII control register
+*
+* The contents of the PHY register containing the needed information need to
+* be passed in.
+******************************************************************************/
+static int32_t
+e1000_config_mac_to_phy(struct e1000_hw *hw)
+{
+ uint32_t ctrl;
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ DEBUGFUNC("e1000_config_mac_to_phy");
+
+ /* 82544 or newer MAC, Auto Speed Detection takes care of
+ * MAC speed/duplex configuration.*/
+ if (hw->mac_type >= e1000_82544)
+ return E1000_SUCCESS;
+
+ /* Read the Device Control Register and set the bits to Force Speed
+ * and Duplex.
+ */
+ ctrl = E1000_READ_REG(hw, CTRL);
+ ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS);
+
+ /* Set up duplex in the Device Control and Transmit Control
+ * registers depending on negotiated values.
+ */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ if(phy_data & M88E1000_PSSR_DPLX)
+ ctrl |= E1000_CTRL_FD;
+ else
+ ctrl &= ~E1000_CTRL_FD;
+
+ e1000_config_collision_dist(hw);
+
+ /* Set up speed in the Device Control register depending on
+ * negotiated values.
+ */
+ if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
+ ctrl |= E1000_CTRL_SPD_1000;
+ else if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
+ ctrl |= E1000_CTRL_SPD_100;
+
+ /* Write the configured values back to the Device Control Reg. */
+ E1000_WRITE_REG(hw, CTRL, ctrl);
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Forces the MAC's flow control settings.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Sets the TFCE and RFCE bits in the device control register to reflect
+ * the adapter settings. TFCE and RFCE need to be explicitly set by
+ * software when a Copper PHY is used because autonegotiation is managed
+ * by the PHY rather than the MAC. Software must also configure these
+ * bits when link is forced on a fiber connection.
+ *****************************************************************************/
+int32_t
+e1000_force_mac_fc(struct e1000_hw *hw)
+{
+ uint32_t ctrl;
+
+ DEBUGFUNC("e1000_force_mac_fc");
+
+ /* Get the current configuration of the Device Control Register */
+ ctrl = E1000_READ_REG(hw, CTRL);
+
+ /* Because we didn't get link via the internal auto-negotiation
+ * mechanism (we either forced link or we got link via PHY
+ * auto-neg), we have to manually enable/disable transmit an
+ * receive flow control.
+ *
+ * The "Case" statement below enables/disable flow control
+ * according to the "hw->fc" parameter.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause
+ * frames but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * frames but we do not receive pause frames).
+ * 3: Both Rx and TX flow control (symmetric) is enabled.
+ * other: No other values should be possible at this point.
+ */
+
+ switch (hw->fc) {
+ case e1000_fc_none:
+ ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
+ break;
+ case e1000_fc_rx_pause:
+ ctrl &= (~E1000_CTRL_TFCE);
+ ctrl |= E1000_CTRL_RFCE;
+ break;
+ case e1000_fc_tx_pause:
+ ctrl &= (~E1000_CTRL_RFCE);
+ ctrl |= E1000_CTRL_TFCE;
+ break;
+ case e1000_fc_full:
+ ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
+ break;
+ default:
+ DEBUGOUT("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ /* Disable TX Flow Control for 82542 (rev 2.0) */
+ if(hw->mac_type == e1000_82542_rev2_0)
+ ctrl &= (~E1000_CTRL_TFCE);
+
+ E1000_WRITE_REG(hw, CTRL, ctrl);
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Configures flow control settings after link is established
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Should be called immediately after a valid link has been established.
+ * Forces MAC flow control settings if link was forced. When in MII/GMII mode
+ * and autonegotiation is enabled, the MAC flow control settings will be set
+ * based on the flow control negotiated by the PHY. In TBI mode, the TFCE
+ * and RFCE bits will be automaticaly set to the negotiated flow control mode.
+ *****************************************************************************/
+static int32_t
+e1000_config_fc_after_link_up(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t mii_status_reg;
+ uint16_t mii_nway_adv_reg;
+ uint16_t mii_nway_lp_ability_reg;
+ uint16_t speed;
+ uint16_t duplex;
+
+ DEBUGFUNC("e1000_config_fc_after_link_up");
+
+ /* Check for the case where we have fiber media and auto-neg failed
+ * so we had to force link. In this case, we need to force the
+ * configuration of the MAC to match the "fc" parameter.
+ */
+ if(((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) ||
+ ((hw->media_type == e1000_media_type_internal_serdes) && (hw->autoneg_failed)) ||
+ ((hw->media_type == e1000_media_type_copper) && (!hw->autoneg))) {
+ ret_val = e1000_force_mac_fc(hw);
+ if(ret_val) {
+ DEBUGOUT("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ }
+
+ /* Check for the case where we have copper media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if((hw->media_type == e1000_media_type_copper) && hw->autoneg) {
+ /* Read the MII Status Register and check to see if AutoNeg
+ * has completed. We read this twice because this reg has
+ * some "sticky" (latched) bits.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if(ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if(ret_val)
+ return ret_val;
+
+ if(mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
+ /* The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement Register
+ * (Address 4) and the Auto_Negotiation Base Page Ability
+ * Register (Address 5) to determine how flow control was
+ * negotiated.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV,
+ &mii_nway_adv_reg);
+ if(ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY,
+ &mii_nway_lp_ability_reg);
+ if(ret_val)
+ return ret_val;
+
+ /* Two bits in the Auto Negotiation Advertisement Register
+ * (Address 4) and two bits in the Auto Negotiation Base
+ * Page Ability Register (Address 5) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | e1000_fc_none
+ * 0 | 1 | 0 | DC | e1000_fc_none
+ * 0 | 1 | 1 | 0 | e1000_fc_none
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ * 1 | 0 | 0 | DC | e1000_fc_none
+ * 1 | DC | 1 | DC | e1000_fc_full
+ * 1 | 1 | 0 | 0 | e1000_fc_none
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ *
+ */
+ /* Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | e1000_fc_full
+ *
+ */
+ if((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+ /* Now we need to check if the user selected RX ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if(hw->original_fc == e1000_fc_full) {
+ hw->fc = e1000_fc_full;
+ DEBUGOUT("Flow Control = FULL.\r\n");
+ } else {
+ hw->fc = e1000_fc_rx_pause;
+ DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
+ }
+ }
+ /* For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ *
+ */
+ else if(!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc = e1000_fc_tx_pause;
+ DEBUGOUT("Flow Control = TX PAUSE frames only.\r\n");
+ }
+ /* For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ *
+ */
+ else if((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc = e1000_fc_rx_pause;
+ DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
+ }
+ /* Per the IEEE spec, at this point flow control should be
+ * disabled. However, we want to consider that we could
+ * be connected to a legacy switch that doesn't advertise
+ * desired flow control, but can be forced on the link
+ * partner. So if we advertised no flow control, that is
+ * what we will resolve to. If we advertised some kind of
+ * receive capability (Rx Pause Only or Full Flow Control)
+ * and the link partner advertised none, we will configure
+ * ourselves to enable Rx Flow Control only. We can do
+ * this safely for two reasons: If the link partner really
+ * didn't want flow control enabled, and we enable Rx, no
+ * harm done since we won't be receiving any PAUSE frames
+ * anyway. If the intent on the link partner was to have
+ * flow control enabled, then by us enabling RX only, we
+ * can at least receive pause frames and process them.
+ * This is a good idea because in most cases, since we are
+ * predominantly a server NIC, more times than not we will
+ * be asked to delay transmission of packets than asking
+ * our link partner to pause transmission of frames.
+ */
+ else if((hw->original_fc == e1000_fc_none ||
+ hw->original_fc == e1000_fc_tx_pause) ||
+ hw->fc_strict_ieee) {
+ hw->fc = e1000_fc_none;
+ DEBUGOUT("Flow Control = NONE.\r\n");
+ } else {
+ hw->fc = e1000_fc_rx_pause;
+ DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
+ }
+
+ /* Now we need to do one last check... If we auto-
+ * negotiated to HALF DUPLEX, flow control should not be
+ * enabled per IEEE 802.3 spec.
+ */
+ ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if(ret_val) {
+ DEBUGOUT("Error getting link speed and duplex\n");
+ return ret_val;
+ }
+
+ if(duplex == HALF_DUPLEX)
+ hw->fc = e1000_fc_none;
+
+ /* Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ ret_val = e1000_force_mac_fc(hw);
+ if(ret_val) {
+ DEBUGOUT("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ } else {
+ DEBUGOUT("Copper PHY and Auto Neg has not completed.\r\n");
+ }
+ }
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Checks to see if the link status of the hardware has changed.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Called by any function that needs to check the link status of the adapter.
+ *****************************************************************************/
+int32_t
+e1000_check_for_link(struct e1000_hw *hw)
+{
+ uint32_t rxcw = 0;
+ uint32_t ctrl;
+ uint32_t status;
+ uint32_t rctl;
+ uint32_t icr;
+ uint32_t signal = 0;
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ DEBUGFUNC("e1000_check_for_link");
+
+ ctrl = E1000_READ_REG(hw, CTRL);
+ status = E1000_READ_REG(hw, STATUS);
+
+ /* On adapters with a MAC newer than 82544, SW Defineable pin 1 will be
+ * set when the optics detect a signal. On older adapters, it will be
+ * cleared when there is a signal. This applies to fiber media only.
+ */
+ if((hw->media_type == e1000_media_type_fiber) ||
+ (hw->media_type == e1000_media_type_internal_serdes)) {
+ rxcw = E1000_READ_REG(hw, RXCW);
+
+ if(hw->media_type == e1000_media_type_fiber) {
+ signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
+ if(status & E1000_STATUS_LU)
+ hw->get_link_status = FALSE;
+ }
+ }
+
+ /* If we have a copper PHY then we only want to go out to the PHY
+ * registers to see if Auto-Neg has completed and/or if our link
+ * status has changed. The get_link_status flag will be set if we
+ * receive a Link Status Change interrupt or we have Rx Sequence
+ * Errors.
+ */
+ if((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
+ /* First we want to see if the MII Status Register reports
+ * link. If so, then we want to get the current speed/duplex
+ * of the PHY.
+ * Read the register twice since the link bit is sticky.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ if(phy_data & MII_SR_LINK_STATUS) {
+ hw->get_link_status = FALSE;
+ /* Check if there was DownShift, must be checked immediately after
+ * link-up */
+ e1000_check_downshift(hw);
+
+ /* If we are on 82544 or 82543 silicon and speed/duplex
+ * are forced to 10H or 10F, then we will implement the polarity
+ * reversal workaround. We disable interrupts first, and upon
+ * returning, place the devices interrupt state to its previous
+ * value except for the link status change interrupt which will
+ * happen due to the execution of this workaround.
+ */
+
+ if((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) &&
+ (!hw->autoneg) &&
+ (hw->forced_speed_duplex == e1000_10_full ||
+ hw->forced_speed_duplex == e1000_10_half)) {
+ E1000_WRITE_REG(hw, IMC, 0xffffffff);
+ ret_val = e1000_polarity_reversal_workaround(hw);
+ icr = E1000_READ_REG(hw, ICR);
+ E1000_WRITE_REG(hw, ICS, (icr & ~E1000_ICS_LSC));
+ E1000_WRITE_REG(hw, IMS, IMS_ENABLE_MASK);
+ }
+
+ } else {
+ /* No link detected */
+ e1000_config_dsp_after_link_change(hw, FALSE);
+ return 0;
+ }
+
+ /* If we are forcing speed/duplex, then we simply return since
+ * we have already determined whether we have link or not.
+ */
+ if(!hw->autoneg) return -E1000_ERR_CONFIG;
+
+ /* optimize the dsp settings for the igp phy */
+ e1000_config_dsp_after_link_change(hw, TRUE);
+
+ /* We have a M88E1000 PHY and Auto-Neg is enabled. If we
+ * have Si on board that is 82544 or newer, Auto
+ * Speed Detection takes care of MAC speed/duplex
+ * configuration. So we only need to configure Collision
+ * Distance in the MAC. Otherwise, we need to force
+ * speed/duplex on the MAC to the current PHY speed/duplex
+ * settings.
+ */
+ if(hw->mac_type >= e1000_82544)
+ e1000_config_collision_dist(hw);
+ else {
+ ret_val = e1000_config_mac_to_phy(hw);
+ if(ret_val) {
+ DEBUGOUT("Error configuring MAC to PHY settings\n");
+ return ret_val;
+ }
+ }
+
+ /* Configure Flow Control now that Auto-Neg has completed. First, we
+ * need to restore the desired flow control settings because we may
+ * have had to re-autoneg with a different link partner.
+ */
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if(ret_val) {
+ DEBUGOUT("Error configuring flow control\n");
+ return ret_val;
+ }
+
+ /* At this point we know that we are on copper and we have
+ * auto-negotiated link. These are conditions for checking the link
+ * partner capability register. We use the link speed to determine if
+ * TBI compatibility needs to be turned on or off. If the link is not
+ * at gigabit speed, then TBI compatibility is not needed. If we are
+ * at gigabit speed, we turn on TBI compatibility.
+ */
+ if(hw->tbi_compatibility_en) {
+ uint16_t speed, duplex;
+ e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if(speed != SPEED_1000) {
+ /* If link speed is not set to gigabit speed, we do not need
+ * to enable TBI compatibility.
+ */
+ if(hw->tbi_compatibility_on) {
+ /* If we previously were in the mode, turn it off. */
+ rctl = E1000_READ_REG(hw, RCTL);
+ rctl &= ~E1000_RCTL_SBP;
+ E1000_WRITE_REG(hw, RCTL, rctl);
+ hw->tbi_compatibility_on = FALSE;
+ }
+ } else {
+ /* If TBI compatibility is was previously off, turn it on. For
+ * compatibility with a TBI link partner, we will store bad
+ * packets. Some frames have an additional byte on the end and
+ * will look like CRC errors to to the hardware.
+ */
+ if(!hw->tbi_compatibility_on) {
+ hw->tbi_compatibility_on = TRUE;
+ rctl = E1000_READ_REG(hw, RCTL);
+ rctl |= E1000_RCTL_SBP;
+ E1000_WRITE_REG(hw, RCTL, rctl);
+ }
+ }
+ }
+ }
+ /* If we don't have link (auto-negotiation failed or link partner cannot
+ * auto-negotiate), the cable is plugged in (we have signal), and our
+ * link partner is not trying to auto-negotiate with us (we are receiving
+ * idles or data), we need to force link up. We also need to give
+ * auto-negotiation time to complete, in case the cable was just plugged
+ * in. The autoneg_failed flag does this.
+ */
+ else if((((hw->media_type == e1000_media_type_fiber) &&
+ ((ctrl & E1000_CTRL_SWDPIN1) == signal)) ||
+ (hw->media_type == e1000_media_type_internal_serdes)) &&
+ (!(status & E1000_STATUS_LU)) &&
+ (!(rxcw & E1000_RXCW_C))) {
+ if(hw->autoneg_failed == 0) {
+ hw->autoneg_failed = 1;
+ return 0;
+ }
+ DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\r\n");
+
+ /* Disable auto-negotiation in the TXCW register */
+ E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE));
+
+ /* Force link-up and also force full-duplex. */
+ ctrl = E1000_READ_REG(hw, CTRL);
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ E1000_WRITE_REG(hw, CTRL, ctrl);
+
+ /* Configure Flow Control after forcing link up. */
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if(ret_val) {
+ DEBUGOUT("Error configuring flow control\n");
+ return ret_val;
+ }
+ }
+ /* If we are forcing link and we are receiving /C/ ordered sets, re-enable
+ * auto-negotiation in the TXCW register and disable forced link in the
+ * Device Control register in an attempt to auto-negotiate with our link
+ * partner.
+ */
+ else if(((hw->media_type == e1000_media_type_fiber) ||
+ (hw->media_type == e1000_media_type_internal_serdes)) &&
+ (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
+ DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\r\n");
+ E1000_WRITE_REG(hw, TXCW, hw->txcw);
+ E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU));
+
+ hw->serdes_link_down = FALSE;
+ }
+ /* If we force link for non-auto-negotiation switch, check link status
+ * based on MAC synchronization for internal serdes media type.
+ */
+ else if((hw->media_type == e1000_media_type_internal_serdes) &&
+ !(E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) {
+ /* SYNCH bit and IV bit are sticky. */
+ udelay(10);
+ if(E1000_RXCW_SYNCH & E1000_READ_REG(hw, RXCW)) {
+ if(!(rxcw & E1000_RXCW_IV)) {
+ hw->serdes_link_down = FALSE;
+ DEBUGOUT("SERDES: Link is up.\n");
+ }
+ } else {
+ hw->serdes_link_down = TRUE;
+ DEBUGOUT("SERDES: Link is down.\n");
+ }
+ }
+ if((hw->media_type == e1000_media_type_internal_serdes) &&
+ (E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) {
+ hw->serdes_link_down = !(E1000_STATUS_LU & E1000_READ_REG(hw, STATUS));
+ }
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Detects the current speed and duplex settings of the hardware.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * speed - Speed of the connection
+ * duplex - Duplex setting of the connection
+ *****************************************************************************/
+int32_t
+e1000_get_speed_and_duplex(struct e1000_hw *hw,
+ uint16_t *speed,
+ uint16_t *duplex)
+{
+ uint32_t status;
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ DEBUGFUNC("e1000_get_speed_and_duplex");
+
+ if(hw->mac_type >= e1000_82543) {
+ status = E1000_READ_REG(hw, STATUS);
+ if(status & E1000_STATUS_SPEED_1000) {
+ *speed = SPEED_1000;
+ DEBUGOUT("1000 Mbs, ");
+ } else if(status & E1000_STATUS_SPEED_100) {
+ *speed = SPEED_100;
+ DEBUGOUT("100 Mbs, ");
+ } else {
+ *speed = SPEED_10;
+ DEBUGOUT("10 Mbs, ");
+ }
+
+ if(status & E1000_STATUS_FD) {
+ *duplex = FULL_DUPLEX;
+ DEBUGOUT("Full Duplex\r\n");
+ } else {
+ *duplex = HALF_DUPLEX;
+ DEBUGOUT(" Half Duplex\r\n");
+ }
+ } else {
+ DEBUGOUT("1000 Mbs, Full Duplex\r\n");
+ *speed = SPEED_1000;
+ *duplex = FULL_DUPLEX;
+ }
+
+ /* IGP01 PHY may advertise full duplex operation after speed downgrade even
+ * if it is operating at half duplex. Here we set the duplex settings to
+ * match the duplex in the link partner's capabilities.
+ */
+ if(hw->phy_type == e1000_phy_igp && hw->speed_downgraded) {
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ if(!(phy_data & NWAY_ER_LP_NWAY_CAPS))
+ *duplex = HALF_DUPLEX;
+ else {
+ ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY, &phy_data);
+ if(ret_val)
+ return ret_val;
+ if((*speed == SPEED_100 && !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) ||
+ (*speed == SPEED_10 && !(phy_data & NWAY_LPAR_10T_FD_CAPS)))
+ *duplex = HALF_DUPLEX;
+ }
+ }
+
+ if ((hw->mac_type == e1000_80003es2lan) &&
+ (hw->media_type == e1000_media_type_copper)) {
+ if (*speed == SPEED_1000)
+ ret_val = e1000_configure_kmrn_for_1000(hw);
+ else
+ ret_val = e1000_configure_kmrn_for_10_100(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Blocks until autoneg completes or times out (~4.5 seconds)
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int32_t
+e1000_wait_autoneg(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t i;
+ uint16_t phy_data;
+
+ DEBUGFUNC("e1000_wait_autoneg");
+ DEBUGOUT("Waiting for Auto-Neg to complete.\n");
+
+ /* We will wait for autoneg to complete or 4.5 seconds to expire. */
+ for(i = PHY_AUTO_NEG_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Auto-Neg
+ * Complete bit to be set.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
+ if(phy_data & MII_SR_AUTONEG_COMPLETE) {
+ return E1000_SUCCESS;
+ }
+ msec_delay(100);
+ }
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Raises the Management Data Clock
+*
+* hw - Struct containing variables accessed by shared code
+* ctrl - Device control register's current value
+******************************************************************************/
+static void
+e1000_raise_mdi_clk(struct e1000_hw *hw,
+ uint32_t *ctrl)
+{
+ /* Raise the clock input to the Management Data Clock (by setting the MDC
+ * bit), and then delay 10 microseconds.
+ */
+ E1000_WRITE_REG(hw, CTRL, (*ctrl | E1000_CTRL_MDC));
+ E1000_WRITE_FLUSH(hw);
+ udelay(10);
+}
+
+/******************************************************************************
+* Lowers the Management Data Clock
+*
+* hw - Struct containing variables accessed by shared code
+* ctrl - Device control register's current value
+******************************************************************************/
+static void
+e1000_lower_mdi_clk(struct e1000_hw *hw,
+ uint32_t *ctrl)
+{
+ /* Lower the clock input to the Management Data Clock (by clearing the MDC
+ * bit), and then delay 10 microseconds.
+ */
+ E1000_WRITE_REG(hw, CTRL, (*ctrl & ~E1000_CTRL_MDC));
+ E1000_WRITE_FLUSH(hw);
+ udelay(10);
+}
+
+/******************************************************************************
+* Shifts data bits out to the PHY
+*
+* hw - Struct containing variables accessed by shared code
+* data - Data to send out to the PHY
+* count - Number of bits to shift out
+*
+* Bits are shifted out in MSB to LSB order.
+******************************************************************************/
+static void
+e1000_shift_out_mdi_bits(struct e1000_hw *hw,
+ uint32_t data,
+ uint16_t count)
+{
+ uint32_t ctrl;
+ uint32_t mask;
+
+ /* We need to shift "count" number of bits out to the PHY. So, the value
+ * in the "data" parameter will be shifted out to the PHY one bit at a
+ * time. In order to do this, "data" must be broken down into bits.
+ */
+ mask = 0x01;
+ mask <<= (count - 1);
+
+ ctrl = E1000_READ_REG(hw, CTRL);
+
+ /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */
+ ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR);
+
+ while(mask) {
+ /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and
+ * then raising and lowering the Management Data Clock. A "0" is
+ * shifted out to the PHY by setting the MDIO bit to "0" and then
+ * raising and lowering the clock.
+ */
+ if(data & mask) ctrl |= E1000_CTRL_MDIO;
+ else ctrl &= ~E1000_CTRL_MDIO;
+
+ E1000_WRITE_REG(hw, CTRL, ctrl);
+ E1000_WRITE_FLUSH(hw);
+
+ udelay(10);
+
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
+
+ mask = mask >> 1;
+ }
+}
+
+/******************************************************************************
+* Shifts data bits in from the PHY
+*
+* hw - Struct containing variables accessed by shared code
+*
+* Bits are shifted in in MSB to LSB order.
+******************************************************************************/
+static uint16_t
+e1000_shift_in_mdi_bits(struct e1000_hw *hw)
+{
+ uint32_t ctrl;
+ uint16_t data = 0;
+ uint8_t i;
+
+ /* In order to read a register from the PHY, we need to shift in a total
+ * of 18 bits from the PHY. The first two bit (turnaround) times are used
+ * to avoid contention on the MDIO pin when a read operation is performed.
+ * These two bits are ignored by us and thrown away. Bits are "shifted in"
+ * by raising the input to the Management Data Clock (setting the MDC bit),
+ * and then reading the value of the MDIO bit.
+ */
+ ctrl = E1000_READ_REG(hw, CTRL);
+
+ /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */
+ ctrl &= ~E1000_CTRL_MDIO_DIR;
+ ctrl &= ~E1000_CTRL_MDIO;
+
+ E1000_WRITE_REG(hw, CTRL, ctrl);
+ E1000_WRITE_FLUSH(hw);
+
+ /* Raise and Lower the clock before reading in the data. This accounts for
+ * the turnaround bits. The first clock occurred when we clocked out the
+ * last bit of the Register Address.
+ */
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
+
+ for(data = 0, i = 0; i < 16; i++) {
+ data = data << 1;
+ e1000_raise_mdi_clk(hw, &ctrl);
+ ctrl = E1000_READ_REG(hw, CTRL);
+ /* Check to see if we shifted in a "1". */
+ if(ctrl & E1000_CTRL_MDIO) data |= 1;
+ e1000_lower_mdi_clk(hw, &ctrl);
+ }
+
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
+
+ return data;
+}
+
+int32_t
+e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask)
+{
+ uint32_t swfw_sync = 0;
+ uint32_t swmask = mask;
+ uint32_t fwmask = mask << 16;
+ int32_t timeout = 200;
+
+ DEBUGFUNC("e1000_swfw_sync_acquire");
+
+ if (!hw->swfw_sync_present)
+ return e1000_get_hw_eeprom_semaphore(hw);
+
+ while(timeout) {
+ if (e1000_get_hw_eeprom_semaphore(hw))
+ return -E1000_ERR_SWFW_SYNC;
+
+ swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
+ if (!(swfw_sync & (fwmask | swmask))) {
+ break;
+ }
+
+ /* firmware currently using resource (fwmask) */
+ /* or other software thread currently using resource (swmask) */
+ e1000_put_hw_eeprom_semaphore(hw);
+ msec_delay_irq(5);
+ timeout--;
+ }
+
+ if (!timeout) {
+ DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n");
+ return -E1000_ERR_SWFW_SYNC;
+ }
+
+ swfw_sync |= swmask;
+ E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync);
+
+ e1000_put_hw_eeprom_semaphore(hw);
+ return E1000_SUCCESS;
+}
+
+void
+e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask)
+{
+ uint32_t swfw_sync;
+ uint32_t swmask = mask;
+
+ DEBUGFUNC("e1000_swfw_sync_release");
+
+ if (!hw->swfw_sync_present) {
+ e1000_put_hw_eeprom_semaphore(hw);
+ return;
+ }
+
+ /* if (e1000_get_hw_eeprom_semaphore(hw))
+ * return -E1000_ERR_SWFW_SYNC; */
+ while (e1000_get_hw_eeprom_semaphore(hw) != E1000_SUCCESS);
+ /* empty */
+
+ swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
+ swfw_sync &= ~swmask;
+ E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync);
+
+ e1000_put_hw_eeprom_semaphore(hw);
+}
+
+/*****************************************************************************
+* Reads the value from a PHY register, if the value is on a specific non zero
+* page, sets the page first.
+* hw - Struct containing variables accessed by shared code
+* reg_addr - address of the PHY register to read
+******************************************************************************/
+int32_t
+e1000_read_phy_reg(struct e1000_hw *hw,
+ uint32_t reg_addr,
+ uint16_t *phy_data)
+{
+ uint32_t ret_val;
+ uint16_t swfw;
+
+ DEBUGFUNC("e1000_read_phy_reg");
+
+ if ((hw->mac_type == e1000_80003es2lan) &&
+ (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) {
+ swfw = E1000_SWFW_PHY1_SM;
+ } else {
+ swfw = E1000_SWFW_PHY0_SM;
+ }
+ if (e1000_swfw_sync_acquire(hw, swfw))
+ return -E1000_ERR_SWFW_SYNC;
+
+ if((hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2) &&
+ (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+ ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (uint16_t)reg_addr);
+ if(ret_val) {
+ e1000_swfw_sync_release(hw, swfw);
+ return ret_val;
+ }
+ } else if (hw->phy_type == e1000_phy_gg82563) {
+ if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) ||
+ (hw->mac_type == e1000_80003es2lan)) {
+ /* Select Configuration Page */
+ if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
+ ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT,
+ (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT));
+ } else {
+ /* Use Alternative Page Select register to access
+ * registers 30 and 31
+ */
+ ret_val = e1000_write_phy_reg_ex(hw,
+ GG82563_PHY_PAGE_SELECT_ALT,
+ (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT));
+ }
+
+ if (ret_val) {
+ e1000_swfw_sync_release(hw, swfw);
+ return ret_val;
+ }
+ }
+ }
+
+ ret_val = e1000_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
+ phy_data);
+
+ e1000_swfw_sync_release(hw, swfw);
+ return ret_val;
+}
+
+int32_t
+e1000_read_phy_reg_ex(struct e1000_hw *hw,
+ uint32_t reg_addr,
+ uint16_t *phy_data)
+{
+ uint32_t i;
+ uint32_t mdic = 0;
+ const uint32_t phy_addr = 1;
+
+ DEBUGFUNC("e1000_read_phy_reg_ex");
+
+ if(reg_addr > MAX_PHY_REG_ADDRESS) {
+ DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
+ return -E1000_ERR_PARAM;
+ }
+
+ if(hw->mac_type > e1000_82543) {
+ /* Set up Op-code, Phy Address, and register address in the MDI
+ * Control register. The MAC will take care of interfacing with the
+ * PHY to retrieve the desired data.
+ */
+ mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
+ (phy_addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_READ));
+
+ E1000_WRITE_REG(hw, MDIC, mdic);
+
+ /* Poll the ready bit to see if the MDI read completed */
+ for(i = 0; i < 64; i++) {
+ udelay(50);
+ mdic = E1000_READ_REG(hw, MDIC);
+ if(mdic & E1000_MDIC_READY) break;
+ }
+ if(!(mdic & E1000_MDIC_READY)) {
+ DEBUGOUT("MDI Read did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ if(mdic & E1000_MDIC_ERROR) {
+ DEBUGOUT("MDI Error\n");
+ return -E1000_ERR_PHY;
+ }
+ *phy_data = (uint16_t) mdic;
+ } else {
+ /* We must first send a preamble through the MDIO pin to signal the
+ * beginning of an MII instruction. This is done by sending 32
+ * consecutive "1" bits.
+ */
+ e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
+
+ /* Now combine the next few fields that are required for a read
+ * operation. We use this method instead of calling the
+ * e1000_shift_out_mdi_bits routine five different times. The format of
+ * a MII read instruction consists of a shift out of 14 bits and is
+ * defined as follows:
+ * <Preamble><SOF><Op Code><Phy Addr><Reg Addr>
+ * followed by a shift in of 18 bits. This first two bits shifted in
+ * are TurnAround bits used to avoid contention on the MDIO pin when a
+ * READ operation is performed. These two bits are thrown away
+ * followed by a shift in of 16 bits which contains the desired data.
+ */
+ mdic = ((reg_addr) | (phy_addr << 5) |
+ (PHY_OP_READ << 10) | (PHY_SOF << 12));
+
+ e1000_shift_out_mdi_bits(hw, mdic, 14);
+
+ /* Now that we've shifted out the read command to the MII, we need to
+ * "shift in" the 16-bit value (18 total bits) of the requested PHY
+ * register address.
+ */
+ *phy_data = e1000_shift_in_mdi_bits(hw);
+ }
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Writes a value to a PHY register
+*
+* hw - Struct containing variables accessed by shared code
+* reg_addr - address of the PHY register to write
+* data - data to write to the PHY
+******************************************************************************/
+int32_t
+e1000_write_phy_reg(struct e1000_hw *hw,
+ uint32_t reg_addr,
+ uint16_t phy_data)
+{
+ uint32_t ret_val;
+ uint16_t swfw;
+
+ DEBUGFUNC("e1000_write_phy_reg");
+
+ if ((hw->mac_type == e1000_80003es2lan) &&
+ (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) {
+ swfw = E1000_SWFW_PHY1_SM;
+ } else {
+ swfw = E1000_SWFW_PHY0_SM;
+ }
+ if (e1000_swfw_sync_acquire(hw, swfw))
+ return -E1000_ERR_SWFW_SYNC;
+
+ if((hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2) &&
+ (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+ ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (uint16_t)reg_addr);
+ if(ret_val) {
+ e1000_swfw_sync_release(hw, swfw);
+ return ret_val;
+ }
+ } else if (hw->phy_type == e1000_phy_gg82563) {
+ if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) ||
+ (hw->mac_type == e1000_80003es2lan)) {
+ /* Select Configuration Page */
+ if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
+ ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT,
+ (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT));
+ } else {
+ /* Use Alternative Page Select register to access
+ * registers 30 and 31
+ */
+ ret_val = e1000_write_phy_reg_ex(hw,
+ GG82563_PHY_PAGE_SELECT_ALT,
+ (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT));
+ }
+
+ if (ret_val) {
+ e1000_swfw_sync_release(hw, swfw);
+ return ret_val;
+ }
+ }
+ }
+
+ ret_val = e1000_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
+ phy_data);
+
+ e1000_swfw_sync_release(hw, swfw);
+ return ret_val;
+}
+
+int32_t
+e1000_write_phy_reg_ex(struct e1000_hw *hw,
+ uint32_t reg_addr,
+ uint16_t phy_data)
+{
+ uint32_t i;
+ uint32_t mdic = 0;
+ const uint32_t phy_addr = 1;
+
+ DEBUGFUNC("e1000_write_phy_reg_ex");
+
+ if(reg_addr > MAX_PHY_REG_ADDRESS) {
+ DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
+ return -E1000_ERR_PARAM;
+ }
+
+ if(hw->mac_type > e1000_82543) {
+ /* Set up Op-code, Phy Address, register address, and data intended
+ * for the PHY register in the MDI Control register. The MAC will take
+ * care of interfacing with the PHY to send the desired data.
+ */
+ mdic = (((uint32_t) phy_data) |
+ (reg_addr << E1000_MDIC_REG_SHIFT) |
+ (phy_addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_WRITE));
+
+ E1000_WRITE_REG(hw, MDIC, mdic);
+
+ /* Poll the ready bit to see if the MDI read completed */
+ for(i = 0; i < 640; i++) {
+ udelay(5);
+ mdic = E1000_READ_REG(hw, MDIC);
+ if(mdic & E1000_MDIC_READY) break;
+ }
+ if(!(mdic & E1000_MDIC_READY)) {
+ DEBUGOUT("MDI Write did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ } else {
+ /* We'll need to use the SW defined pins to shift the write command
+ * out to the PHY. We first send a preamble to the PHY to signal the
+ * beginning of the MII instruction. This is done by sending 32
+ * consecutive "1" bits.
+ */
+ e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
+
+ /* Now combine the remaining required fields that will indicate a
+ * write operation. We use this method instead of calling the
+ * e1000_shift_out_mdi_bits routine for each field in the command. The
+ * format of a MII write instruction is as follows:
+ * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>.
+ */
+ mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) |
+ (PHY_OP_WRITE << 12) | (PHY_SOF << 14));
+ mdic <<= 16;
+ mdic |= (uint32_t) phy_data;
+
+ e1000_shift_out_mdi_bits(hw, mdic, 32);
+ }
+
+ return E1000_SUCCESS;
+}
+
+int32_t
+e1000_read_kmrn_reg(struct e1000_hw *hw,
+ uint32_t reg_addr,
+ uint16_t *data)
+{
+ uint32_t reg_val;
+ uint16_t swfw;
+ DEBUGFUNC("e1000_read_kmrn_reg");
+
+ if ((hw->mac_type == e1000_80003es2lan) &&
+ (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) {
+ swfw = E1000_SWFW_PHY1_SM;
+ } else {
+ swfw = E1000_SWFW_PHY0_SM;
+ }
+ if (e1000_swfw_sync_acquire(hw, swfw))
+ return -E1000_ERR_SWFW_SYNC;
+
+ /* Write register address */
+ reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) &
+ E1000_KUMCTRLSTA_OFFSET) |
+ E1000_KUMCTRLSTA_REN;
+ E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val);
+ udelay(2);
+
+ /* Read the data returned */
+ reg_val = E1000_READ_REG(hw, KUMCTRLSTA);
+ *data = (uint16_t)reg_val;
+
+ e1000_swfw_sync_release(hw, swfw);
+ return E1000_SUCCESS;
+}
+
+int32_t
+e1000_write_kmrn_reg(struct e1000_hw *hw,
+ uint32_t reg_addr,
+ uint16_t data)
+{
+ uint32_t reg_val;
+ uint16_t swfw;
+ DEBUGFUNC("e1000_write_kmrn_reg");
+
+ if ((hw->mac_type == e1000_80003es2lan) &&
+ (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) {
+ swfw = E1000_SWFW_PHY1_SM;
+ } else {
+ swfw = E1000_SWFW_PHY0_SM;
+ }
+ if (e1000_swfw_sync_acquire(hw, swfw))
+ return -E1000_ERR_SWFW_SYNC;
+
+ reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) &
+ E1000_KUMCTRLSTA_OFFSET) | data;
+ E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val);
+ udelay(2);
+
+ e1000_swfw_sync_release(hw, swfw);
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Returns the PHY to the power-on reset state
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+int32_t
+e1000_phy_hw_reset(struct e1000_hw *hw)
+{
+ uint32_t ctrl, ctrl_ext;
+ uint32_t led_ctrl;
+ int32_t ret_val;
+ uint16_t swfw;
+
+ DEBUGFUNC("e1000_phy_hw_reset");
+
+ /* In the case of the phy reset being blocked, it's not an error, we
+ * simply return success without performing the reset. */
+ ret_val = e1000_check_phy_reset_block(hw);
+ if (ret_val)
+ return E1000_SUCCESS;
+
+ DEBUGOUT("Resetting Phy...\n");
+
+ if(hw->mac_type > e1000_82543) {
+ if ((hw->mac_type == e1000_80003es2lan) &&
+ (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) {
+ swfw = E1000_SWFW_PHY1_SM;
+ } else {
+ swfw = E1000_SWFW_PHY0_SM;
+ }
+ if (e1000_swfw_sync_acquire(hw, swfw)) {
+ e1000_release_software_semaphore(hw);
+ return -E1000_ERR_SWFW_SYNC;
+ }
+ /* Read the device control register and assert the E1000_CTRL_PHY_RST
+ * bit. Then, take it out of reset.
+ * For pre-e1000_82571 hardware, we delay for 10ms between the assert
+ * and deassert. For e1000_82571 hardware and later, we instead delay
+ * for 50us between and 10ms after the deassertion.
+ */
+ ctrl = E1000_READ_REG(hw, CTRL);
+ E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST);
+ E1000_WRITE_FLUSH(hw);
+
+ if (hw->mac_type < e1000_82571)
+ msec_delay(10);
+ else
+ udelay(100);
+
+ E1000_WRITE_REG(hw, CTRL, ctrl);
+ E1000_WRITE_FLUSH(hw);
+
+ if (hw->mac_type >= e1000_82571)
+ msec_delay(10);
+ e1000_swfw_sync_release(hw, swfw);
+ } else {
+ /* Read the Extended Device Control Register, assert the PHY_RESET_DIR
+ * bit to put the PHY into reset. Then, take it out of reset.
+ */
+ ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR;
+ ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA;
+ E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH(hw);
+ msec_delay(10);
+ ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA;
+ E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH(hw);
+ }
+ udelay(150);
+
+ if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ /* Configure activity LED after PHY reset */
+ led_ctrl = E1000_READ_REG(hw, LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
+ }
+
+ /* Wait for FW to finish PHY configuration. */
+ ret_val = e1000_get_phy_cfg_done(hw);
+ e1000_release_software_semaphore(hw);
+
+ return ret_val;
+}
+
+/******************************************************************************
+* Resets the PHY
+*
+* hw - Struct containing variables accessed by shared code
+*
+* Sets bit 15 of the MII Control regiser
+******************************************************************************/
+int32_t
+e1000_phy_reset(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ DEBUGFUNC("e1000_phy_reset");
+
+ /* In the case of the phy reset being blocked, it's not an error, we
+ * simply return success without performing the reset. */
+ ret_val = e1000_check_phy_reset_block(hw);
+ if (ret_val)
+ return E1000_SUCCESS;
+
+ switch (hw->mac_type) {
+ case e1000_82541_rev_2:
+ case e1000_82571:
+ case e1000_82572:
+ ret_val = e1000_phy_hw_reset(hw);
+ if(ret_val)
+ return ret_val;
+ break;
+ default:
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data |= MII_CR_RESET;
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
+
+ udelay(1);
+ break;
+ }
+
+ if(hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2)
+ e1000_phy_init_script(hw);
+
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Probes the expected PHY address for known PHY IDs
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int32_t
+e1000_detect_gig_phy(struct e1000_hw *hw)
+{
+ int32_t phy_init_status, ret_val;
+ uint16_t phy_id_high, phy_id_low;
+ boolean_t match = FALSE;
+
+ DEBUGFUNC("e1000_detect_gig_phy");
+
+ /* The 82571 firmware may still be configuring the PHY. In this
+ * case, we cannot access the PHY until the configuration is done. So
+ * we explicitly set the PHY values. */
+ if(hw->mac_type == e1000_82571 ||
+ hw->mac_type == e1000_82572) {
+ hw->phy_id = IGP01E1000_I_PHY_ID;
+ hw->phy_type = e1000_phy_igp_2;
+ return E1000_SUCCESS;
+ }
+
+ /* ESB-2 PHY reads require e1000_phy_gg82563 to be set because of a work-
+ * around that forces PHY page 0 to be set or the reads fail. The rest of
+ * the code in this routine uses e1000_read_phy_reg to read the PHY ID.
+ * So for ESB-2 we need to have this set so our reads won't fail. If the
+ * attached PHY is not a e1000_phy_gg82563, the routines below will figure
+ * this out as well. */
+ if (hw->mac_type == e1000_80003es2lan)
+ hw->phy_type = e1000_phy_gg82563;
+
+ /* Read the PHY ID Registers to identify which PHY is onboard. */
+ ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
+ if(ret_val)
+ return ret_val;
+
+ hw->phy_id = (uint32_t) (phy_id_high << 16);
+ udelay(20);
+ ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low);
+ if(ret_val)
+ return ret_val;
+
+ hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK);
+ hw->phy_revision = (uint32_t) phy_id_low & ~PHY_REVISION_MASK;
+
+ switch(hw->mac_type) {
+ case e1000_82543:
+ if(hw->phy_id == M88E1000_E_PHY_ID) match = TRUE;
+ break;
+ case e1000_82544:
+ if(hw->phy_id == M88E1000_I_PHY_ID) match = TRUE;
+ break;
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ if(hw->phy_id == M88E1011_I_PHY_ID) match = TRUE;
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ if(hw->phy_id == IGP01E1000_I_PHY_ID) match = TRUE;
+ break;
+ case e1000_82573:
+ if(hw->phy_id == M88E1111_I_PHY_ID) match = TRUE;
+ break;
+ case e1000_80003es2lan:
+ if (hw->phy_id == GG82563_E_PHY_ID) match = TRUE;
+ break;
+ default:
+ DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
+ return -E1000_ERR_CONFIG;
+ }
+ phy_init_status = e1000_set_phy_type(hw);
+
+ if ((match) && (phy_init_status == E1000_SUCCESS)) {
+ DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id);
+ return E1000_SUCCESS;
+ }
+ DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id);
+ return -E1000_ERR_PHY;
+}
+
+/******************************************************************************
+* Resets the PHY's DSP
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int32_t
+e1000_phy_reset_dsp(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ DEBUGFUNC("e1000_phy_reset_dsp");
+
+ do {
+ if (hw->phy_type != e1000_phy_gg82563) {
+ ret_val = e1000_write_phy_reg(hw, 29, 0x001d);
+ if(ret_val) break;
+ }
+ ret_val = e1000_write_phy_reg(hw, 30, 0x00c1);
+ if(ret_val) break;
+ ret_val = e1000_write_phy_reg(hw, 30, 0x0000);
+ if(ret_val) break;
+ ret_val = E1000_SUCCESS;
+ } while(0);
+
+ return ret_val;
+}
+
+/******************************************************************************
+* Get PHY information from various PHY registers for igp PHY only.
+*
+* hw - Struct containing variables accessed by shared code
+* phy_info - PHY information structure
+******************************************************************************/
+static int32_t
+e1000_phy_igp_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info)
+{
+ int32_t ret_val;
+ uint16_t phy_data, polarity, min_length, max_length, average;
+
+ DEBUGFUNC("e1000_phy_igp_get_info");
+
+ /* The downshift status is checked only once, after link is established,
+ * and it stored in the hw->speed_downgraded parameter. */
+ phy_info->downshift = (e1000_downshift)hw->speed_downgraded;
+
+ /* IGP01E1000 does not need to support it. */
+ phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal;
+
+ /* IGP01E1000 always correct polarity reversal */
+ phy_info->polarity_correction = e1000_polarity_reversal_enabled;
+
+ /* Check polarity status */
+ ret_val = e1000_check_polarity(hw, &polarity);
+ if(ret_val)
+ return ret_val;
+
+ phy_info->cable_polarity = polarity;
+
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_info->mdix_mode = (phy_data & IGP01E1000_PSSR_MDIX) >>
+ IGP01E1000_PSSR_MDIX_SHIFT;
+
+ if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+ /* Local/Remote Receiver Information are only valid at 1000 Mbps */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_info->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS) >>
+ SR_1000T_LOCAL_RX_STATUS_SHIFT;
+ phy_info->remote_rx = (phy_data & SR_1000T_REMOTE_RX_STATUS) >>
+ SR_1000T_REMOTE_RX_STATUS_SHIFT;
+
+ /* Get cable length */
+ ret_val = e1000_get_cable_length(hw, &min_length, &max_length);
+ if(ret_val)
+ return ret_val;
+
+ /* Translate to old method */
+ average = (max_length + min_length) / 2;
+
+ if(average <= e1000_igp_cable_length_50)
+ phy_info->cable_length = e1000_cable_length_50;
+ else if(average <= e1000_igp_cable_length_80)
+ phy_info->cable_length = e1000_cable_length_50_80;
+ else if(average <= e1000_igp_cable_length_110)
+ phy_info->cable_length = e1000_cable_length_80_110;
+ else if(average <= e1000_igp_cable_length_140)
+ phy_info->cable_length = e1000_cable_length_110_140;
+ else
+ phy_info->cable_length = e1000_cable_length_140;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Get PHY information from various PHY registers fot m88 PHY only.
+*
+* hw - Struct containing variables accessed by shared code
+* phy_info - PHY information structure
+******************************************************************************/
+static int32_t
+e1000_phy_m88_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info)
+{
+ int32_t ret_val;
+ uint16_t phy_data, polarity;
+
+ DEBUGFUNC("e1000_phy_m88_get_info");
+
+ /* The downshift status is checked only once, after link is established,
+ * and it stored in the hw->speed_downgraded parameter. */
+ phy_info->downshift = (e1000_downshift)hw->speed_downgraded;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_info->extended_10bt_distance =
+ (phy_data & M88E1000_PSCR_10BT_EXT_DIST_ENABLE) >>
+ M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT;
+ phy_info->polarity_correction =
+ (phy_data & M88E1000_PSCR_POLARITY_REVERSAL) >>
+ M88E1000_PSCR_POLARITY_REVERSAL_SHIFT;
+
+ /* Check polarity status */
+ ret_val = e1000_check_polarity(hw, &polarity);
+ if(ret_val)
+ return ret_val;
+ phy_info->cable_polarity = polarity;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_info->mdix_mode = (phy_data & M88E1000_PSSR_MDIX) >>
+ M88E1000_PSSR_MDIX_SHIFT;
+
+ if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) {
+ /* Cable Length Estimation and Local/Remote Receiver Information
+ * are only valid at 1000 Mbps.
+ */
+ if (hw->phy_type != e1000_phy_gg82563) {
+ phy_info->cable_length = ((phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT);
+ } else {
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->cable_length = phy_data & GG82563_DSPD_CABLE_LENGTH;
+ }
+
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_info->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS) >>
+ SR_1000T_LOCAL_RX_STATUS_SHIFT;
+
+ phy_info->remote_rx = (phy_data & SR_1000T_REMOTE_RX_STATUS) >>
+ SR_1000T_REMOTE_RX_STATUS_SHIFT;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Get PHY information from various PHY registers
+*
+* hw - Struct containing variables accessed by shared code
+* phy_info - PHY information structure
+******************************************************************************/
+int32_t
+e1000_phy_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info)
+{
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ DEBUGFUNC("e1000_phy_get_info");
+
+ phy_info->cable_length = e1000_cable_length_undefined;
+ phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_undefined;
+ phy_info->cable_polarity = e1000_rev_polarity_undefined;
+ phy_info->downshift = e1000_downshift_undefined;
+ phy_info->polarity_correction = e1000_polarity_reversal_undefined;
+ phy_info->mdix_mode = e1000_auto_x_mode_undefined;
+ phy_info->local_rx = e1000_1000t_rx_status_undefined;
+ phy_info->remote_rx = e1000_1000t_rx_status_undefined;
+
+ if(hw->media_type != e1000_media_type_copper) {
+ DEBUGOUT("PHY info is only valid for copper media\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ if((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) {
+ DEBUGOUT("PHY info is only valid if link is up\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ if(hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2)
+ return e1000_phy_igp_get_info(hw, phy_info);
+ else
+ return e1000_phy_m88_get_info(hw, phy_info);
+}
+
+int32_t
+e1000_validate_mdi_setting(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_validate_mdi_settings");
+
+ if(!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) {
+ DEBUGOUT("Invalid MDI setting detected\n");
+ hw->mdix = 1;
+ return -E1000_ERR_CONFIG;
+ }
+ return E1000_SUCCESS;
+}
+
+
+/******************************************************************************
+ * Sets up eeprom variables in the hw struct. Must be called after mac_type
+ * is configured. Additionally, if this is ICH8, the flash controller GbE
+ * registers must be mapped, or this will crash.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+int32_t
+e1000_init_eeprom_params(struct e1000_hw *hw)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ uint32_t eecd = E1000_READ_REG(hw, EECD);
+ int32_t ret_val = E1000_SUCCESS;
+ uint16_t eeprom_size;
+
+ DEBUGFUNC("e1000_init_eeprom_params");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->word_size = 64;
+ eeprom->opcode_bits = 3;
+ eeprom->address_bits = 6;
+ eeprom->delay_usec = 50;
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ break;
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->opcode_bits = 3;
+ eeprom->delay_usec = 50;
+ if(eecd & E1000_EECD_SIZE) {
+ eeprom->word_size = 256;
+ eeprom->address_bits = 8;
+ } else {
+ eeprom->word_size = 64;
+ eeprom->address_bits = 6;
+ }
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ if (eecd & E1000_EECD_TYPE) {
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
}
-
- /* Now we need to do one last check... If we auto-
- * negotiated to HALF DUPLEX, flow control should not be
- * enabled per IEEE 802.3 spec.
- */
- ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
- if(ret_val) {
- DEBUGOUT("Error getting link speed and duplex\n");
- return ret_val;
+ } else {
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->opcode_bits = 3;
+ eeprom->delay_usec = 50;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->word_size = 256;
+ eeprom->address_bits = 8;
+ } else {
+ eeprom->word_size = 64;
+ eeprom->address_bits = 6;
}
+ }
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ break;
+ case e1000_82571:
+ case e1000_82572:
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ break;
+ case e1000_82573:
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ eeprom->use_eerd = TRUE;
+ eeprom->use_eewr = TRUE;
+ if(e1000_is_onboard_nvm_eeprom(hw) == FALSE) {
+ eeprom->type = e1000_eeprom_flash;
+ eeprom->word_size = 2048;
+
+ /* Ensure that the Autonomous FLASH update bit is cleared due to
+ * Flash update issue on parts which use a FLASH for NVM. */
+ eecd &= ~E1000_EECD_AUPDEN;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ }
+ break;
+ case e1000_80003es2lan:
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ eeprom->use_eerd = TRUE;
+ eeprom->use_eewr = FALSE;
+ break;
+ default:
+ break;
+ }
- if(duplex == HALF_DUPLEX)
- hw->fc = e1000_fc_none;
-
- /* Now we call a subroutine to actually force the MAC
- * controller to use the correct flow control settings.
- */
- ret_val = e1000_force_mac_fc(hw);
- if(ret_val) {
- DEBUGOUT("Error forcing flow control settings\n");
+ if (eeprom->type == e1000_eeprom_spi) {
+ /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to
+ * 32KB (incremented by powers of 2).
+ */
+ if(hw->mac_type <= e1000_82547_rev_2) {
+ /* Set to default value for initial eeprom read. */
+ eeprom->word_size = 64;
+ ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size);
+ if(ret_val)
return ret_val;
- }
+ eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT;
+ /* 256B eeprom size was not supported in earlier hardware, so we
+ * bump eeprom_size up one to ensure that "1" (which maps to 256B)
+ * is never the result used in the shifting logic below. */
+ if(eeprom_size)
+ eeprom_size++;
} else {
- DEBUGOUT("Copper PHY and Auto Neg has not completed.\r\n");
+ eeprom_size = (uint16_t)((eecd & E1000_EECD_SIZE_EX_MASK) >>
+ E1000_EECD_SIZE_EX_SHIFT);
}
+
+ eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT);
}
- return E1000_SUCCESS;
+ return ret_val;
}
/******************************************************************************
- * Checks to see if the link status of the hardware has changed.
+ * Raises the EEPROM's clock input.
*
* hw - Struct containing variables accessed by shared code
+ * eecd - EECD's current value
+ *****************************************************************************/
+static void
+e1000_raise_ee_clk(struct e1000_hw *hw,
+ uint32_t *eecd)
+{
+ /* Raise the clock input to the EEPROM (by setting the SK bit), and then
+ * wait <delay> microseconds.
+ */
+ *eecd = *eecd | E1000_EECD_SK;
+ E1000_WRITE_REG(hw, EECD, *eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(hw->eeprom.delay_usec);
+}
+
+/******************************************************************************
+ * Lowers the EEPROM's clock input.
*
- * Called by any function that needs to check the link status of the adapter.
+ * hw - Struct containing variables accessed by shared code
+ * eecd - EECD's current value
*****************************************************************************/
-int32_t
-e1000_check_for_link(struct e1000_hw *hw)
+static void
+e1000_lower_ee_clk(struct e1000_hw *hw,
+ uint32_t *eecd)
{
- uint32_t rxcw;
- uint32_t ctrl;
- uint32_t status;
- uint32_t rctl;
- uint32_t signal = 0;
- int32_t ret_val;
- uint16_t phy_data;
+ /* Lower the clock input to the EEPROM (by clearing the SK bit), and then
+ * wait 50 microseconds.
+ */
+ *eecd = *eecd & ~E1000_EECD_SK;
+ E1000_WRITE_REG(hw, EECD, *eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(hw->eeprom.delay_usec);
+}
- DEBUGFUNC("e1000_check_for_link");
+/******************************************************************************
+ * Shift data bits out to the EEPROM.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * data - data to send to the EEPROM
+ * count - number of bits to shift out
+ *****************************************************************************/
+static void
+e1000_shift_out_ee_bits(struct e1000_hw *hw,
+ uint16_t data,
+ uint16_t count)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ uint32_t eecd;
+ uint32_t mask;
- /* On adapters with a MAC newer than 82544, SW Defineable pin 1 will be
- * set when the optics detect a signal. On older adapters, it will be
- * cleared when there is a signal. This applies to fiber media only.
+ /* We need to shift "count" bits out to the EEPROM. So, value in the
+ * "data" parameter will be shifted out to the EEPROM one bit at a time.
+ * In order to do this, "data" must be broken down into bits.
*/
- if(hw->media_type == e1000_media_type_fiber)
- signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
+ mask = 0x01 << (count - 1);
+ eecd = E1000_READ_REG(hw, EECD);
+ if (eeprom->type == e1000_eeprom_microwire) {
+ eecd &= ~E1000_EECD_DO;
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ eecd |= E1000_EECD_DO;
+ }
+ do {
+ /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1",
+ * and then raising and then lowering the clock (the SK bit controls
+ * the clock input to the EEPROM). A "0" is shifted out to the EEPROM
+ * by setting "DI" to "0" and then raising and then lowering the clock.
+ */
+ eecd &= ~E1000_EECD_DI;
- ctrl = E1000_READ_REG(hw, CTRL);
- status = E1000_READ_REG(hw, STATUS);
- rxcw = E1000_READ_REG(hw, RXCW);
+ if(data & mask)
+ eecd |= E1000_EECD_DI;
- /* If we have a copper PHY then we only want to go out to the PHY
- * registers to see if Auto-Neg has completed and/or if our link
- * status has changed. The get_link_status flag will be set if we
- * receive a Link Status Change interrupt or we have Rx Sequence
- * Errors.
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+
+ udelay(eeprom->delay_usec);
+
+ e1000_raise_ee_clk(hw, &eecd);
+ e1000_lower_ee_clk(hw, &eecd);
+
+ mask = mask >> 1;
+
+ } while(mask);
+
+ /* We leave the "DI" bit set to "0" when we leave this routine. */
+ eecd &= ~E1000_EECD_DI;
+ E1000_WRITE_REG(hw, EECD, eecd);
+}
+
+/******************************************************************************
+ * Shift data bits in from the EEPROM
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static uint16_t
+e1000_shift_in_ee_bits(struct e1000_hw *hw,
+ uint16_t count)
+{
+ uint32_t eecd;
+ uint32_t i;
+ uint16_t data;
+
+ /* In order to read a register from the EEPROM, we need to shift 'count'
+ * bits in from the EEPROM. Bits are "shifted in" by raising the clock
+ * input to the EEPROM (setting the SK bit), and then reading the value of
+ * the "DO" bit. During this "shifting in" process the "DI" bit should
+ * always be clear.
*/
- if((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
- /* First we want to see if the MII Status Register reports
- * link. If so, then we want to get the current speed/duplex
- * of the PHY.
- * Read the register twice since the link bit is sticky.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
- return ret_val;
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
- return ret_val;
- if(phy_data & MII_SR_LINK_STATUS) {
- hw->get_link_status = FALSE;
- /* Check if there was DownShift, must be checked immediately after
- * link-up */
- e1000_check_downshift(hw);
+ eecd = E1000_READ_REG(hw, EECD);
- } else {
- /* No link detected */
- e1000_config_dsp_after_link_change(hw, FALSE);
- return 0;
- }
+ eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
+ data = 0;
- /* If we are forcing speed/duplex, then we simply return since
- * we have already determined whether we have link or not.
- */
- if(!hw->autoneg) return -E1000_ERR_CONFIG;
+ for(i = 0; i < count; i++) {
+ data = data << 1;
+ e1000_raise_ee_clk(hw, &eecd);
- /* optimize the dsp settings for the igp phy */
- e1000_config_dsp_after_link_change(hw, TRUE);
+ eecd = E1000_READ_REG(hw, EECD);
+
+ eecd &= ~(E1000_EECD_DI);
+ if(eecd & E1000_EECD_DO)
+ data |= 1;
+
+ e1000_lower_ee_clk(hw, &eecd);
+ }
+
+ return data;
+}
+
+/******************************************************************************
+ * Prepares EEPROM for access
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This
+ * function should be called before issuing a command to the EEPROM.
+ *****************************************************************************/
+static int32_t
+e1000_acquire_eeprom(struct e1000_hw *hw)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ uint32_t eecd, i=0;
- /* We have a M88E1000 PHY and Auto-Neg is enabled. If we
- * have Si on board that is 82544 or newer, Auto
- * Speed Detection takes care of MAC speed/duplex
- * configuration. So we only need to configure Collision
- * Distance in the MAC. Otherwise, we need to force
- * speed/duplex on the MAC to the current PHY speed/duplex
- * settings.
- */
- if(hw->mac_type >= e1000_82544)
- e1000_config_collision_dist(hw);
- else {
- ret_val = e1000_config_mac_to_phy(hw);
- if(ret_val) {
- DEBUGOUT("Error configuring MAC to PHY settings\n");
- return ret_val;
- }
- }
+ DEBUGFUNC("e1000_acquire_eeprom");
- /* Configure Flow Control now that Auto-Neg has completed. First, we
- * need to restore the desired flow control settings because we may
- * have had to re-autoneg with a different link partner.
- */
- ret_val = e1000_config_fc_after_link_up(hw);
- if(ret_val) {
- DEBUGOUT("Error configuring flow control\n");
- return ret_val;
- }
+ if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM))
+ return -E1000_ERR_SWFW_SYNC;
+ eecd = E1000_READ_REG(hw, EECD);
- /* At this point we know that we are on copper and we have
- * auto-negotiated link. These are conditions for checking the link
- * partner capability register. We use the link speed to determine if
- * TBI compatibility needs to be turned on or off. If the link is not
- * at gigabit speed, then TBI compatibility is not needed. If we are
- * at gigabit speed, we turn on TBI compatibility.
- */
- if(hw->tbi_compatibility_en) {
- uint16_t speed, duplex;
- e1000_get_speed_and_duplex(hw, &speed, &duplex);
- if(speed != SPEED_1000) {
- /* If link speed is not set to gigabit speed, we do not need
- * to enable TBI compatibility.
- */
- if(hw->tbi_compatibility_on) {
- /* If we previously were in the mode, turn it off. */
- rctl = E1000_READ_REG(hw, RCTL);
- rctl &= ~E1000_RCTL_SBP;
- E1000_WRITE_REG(hw, RCTL, rctl);
- hw->tbi_compatibility_on = FALSE;
- }
- } else {
- /* If TBI compatibility is was previously off, turn it on. For
- * compatibility with a TBI link partner, we will store bad
- * packets. Some frames have an additional byte on the end and
- * will look like CRC errors to to the hardware.
- */
- if(!hw->tbi_compatibility_on) {
- hw->tbi_compatibility_on = TRUE;
- rctl = E1000_READ_REG(hw, RCTL);
- rctl |= E1000_RCTL_SBP;
- E1000_WRITE_REG(hw, RCTL, rctl);
- }
+ if (hw->mac_type != e1000_82573) {
+ /* Request EEPROM Access */
+ if(hw->mac_type > e1000_82544) {
+ eecd |= E1000_EECD_REQ;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ eecd = E1000_READ_REG(hw, EECD);
+ while((!(eecd & E1000_EECD_GNT)) &&
+ (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
+ i++;
+ udelay(5);
+ eecd = E1000_READ_REG(hw, EECD);
+ }
+ if(!(eecd & E1000_EECD_GNT)) {
+ eecd &= ~E1000_EECD_REQ;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ DEBUGOUT("Could not acquire EEPROM grant\n");
+ e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
+ return -E1000_ERR_EEPROM;
}
}
}
- /* If we don't have link (auto-negotiation failed or link partner cannot
- * auto-negotiate), the cable is plugged in (we have signal), and our
- * link partner is not trying to auto-negotiate with us (we are receiving
- * idles or data), we need to force link up. We also need to give
- * auto-negotiation time to complete, in case the cable was just plugged
- * in. The autoneg_failed flag does this.
- */
- else if((((hw->media_type == e1000_media_type_fiber) &&
- ((ctrl & E1000_CTRL_SWDPIN1) == signal)) ||
- (hw->media_type == e1000_media_type_internal_serdes)) &&
- (!(status & E1000_STATUS_LU)) &&
- (!(rxcw & E1000_RXCW_C))) {
- if(hw->autoneg_failed == 0) {
- hw->autoneg_failed = 1;
- return 0;
- }
- DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\r\n");
- /* Disable auto-negotiation in the TXCW register */
- E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE));
+ /* Setup EEPROM for Read/Write */
- /* Force link-up and also force full-duplex. */
- ctrl = E1000_READ_REG(hw, CTRL);
- ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
- E1000_WRITE_REG(hw, CTRL, ctrl);
+ if (eeprom->type == e1000_eeprom_microwire) {
+ /* Clear SK and DI */
+ eecd &= ~(E1000_EECD_DI | E1000_EECD_SK);
+ E1000_WRITE_REG(hw, EECD, eecd);
- /* Configure Flow Control after forcing link up. */
- ret_val = e1000_config_fc_after_link_up(hw);
- if(ret_val) {
- DEBUGOUT("Error configuring flow control\n");
- return ret_val;
- }
+ /* Set CS */
+ eecd |= E1000_EECD_CS;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ /* Clear SK and CS */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ E1000_WRITE_REG(hw, EECD, eecd);
+ udelay(1);
}
- /* If we are forcing link and we are receiving /C/ ordered sets, re-enable
- * auto-negotiation in the TXCW register and disable forced link in the
- * Device Control register in an attempt to auto-negotiate with our link
- * partner.
- */
- else if(((hw->media_type == e1000_media_type_fiber) ||
- (hw->media_type == e1000_media_type_internal_serdes)) &&
- (ctrl & E1000_CTRL_SLU) &&
- (rxcw & E1000_RXCW_C)) {
- DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\r\n");
- E1000_WRITE_REG(hw, TXCW, hw->txcw);
- E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU));
- hw->serdes_link_down = FALSE;
- }
- /* If we force link for non-auto-negotiation switch, check link status
- * based on MAC synchronization for internal serdes media type.
- */
- else if((hw->media_type == e1000_media_type_internal_serdes) &&
- !(E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) {
- /* SYNCH bit and IV bit are sticky. */
- udelay(10);
- if(E1000_RXCW_SYNCH & E1000_READ_REG(hw, RXCW)) {
- if(!(rxcw & E1000_RXCW_IV)) {
- hw->serdes_link_down = FALSE;
- DEBUGOUT("SERDES: Link is up.\n");
- }
- } else {
- hw->serdes_link_down = TRUE;
- DEBUGOUT("SERDES: Link is down.\n");
- }
- }
- if((hw->media_type == e1000_media_type_internal_serdes) &&
- (E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) {
- hw->serdes_link_down = !(E1000_STATUS_LU & E1000_READ_REG(hw, STATUS));
- }
return E1000_SUCCESS;
}
/******************************************************************************
- * Detects the current speed and duplex settings of the hardware.
+ * Returns EEPROM to a "standby" state
*
* hw - Struct containing variables accessed by shared code
- * speed - Speed of the connection
- * duplex - Duplex setting of the connection
*****************************************************************************/
-int32_t
-e1000_get_speed_and_duplex(struct e1000_hw *hw,
- uint16_t *speed,
- uint16_t *duplex)
+static void
+e1000_standby_eeprom(struct e1000_hw *hw)
{
- uint32_t status;
- int32_t ret_val;
- uint16_t phy_data;
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ uint32_t eecd;
- DEBUGFUNC("e1000_get_speed_and_duplex");
+ eecd = E1000_READ_REG(hw, EECD);
- if(hw->mac_type >= e1000_82543) {
- status = E1000_READ_REG(hw, STATUS);
- if(status & E1000_STATUS_SPEED_1000) {
- *speed = SPEED_1000;
- DEBUGOUT("1000 Mbs, ");
- } else if(status & E1000_STATUS_SPEED_100) {
- *speed = SPEED_100;
- DEBUGOUT("100 Mbs, ");
- } else {
- *speed = SPEED_10;
- DEBUGOUT("10 Mbs, ");
- }
+ if(eeprom->type == e1000_eeprom_microwire) {
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
- if(status & E1000_STATUS_FD) {
- *duplex = FULL_DUPLEX;
- DEBUGOUT("Full Duplex\r\n");
- } else {
- *duplex = HALF_DUPLEX;
- DEBUGOUT(" Half Duplex\r\n");
- }
- } else {
- DEBUGOUT("1000 Mbs, Full Duplex\r\n");
- *speed = SPEED_1000;
- *duplex = FULL_DUPLEX;
+ /* Clock high */
+ eecd |= E1000_EECD_SK;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
+
+ /* Select EEPROM */
+ eecd |= E1000_EECD_CS;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
+
+ /* Clock low */
+ eecd &= ~E1000_EECD_SK;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
+ } else if(eeprom->type == e1000_eeprom_spi) {
+ /* Toggle CS to flush commands */
+ eecd |= E1000_EECD_CS;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
+ eecd &= ~E1000_EECD_CS;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
+ }
+}
+
+/******************************************************************************
+ * Terminates a command by inverting the EEPROM's chip select pin
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static void
+e1000_release_eeprom(struct e1000_hw *hw)
+{
+ uint32_t eecd;
+
+ DEBUGFUNC("e1000_release_eeprom");
+
+ eecd = E1000_READ_REG(hw, EECD);
+
+ if (hw->eeprom.type == e1000_eeprom_spi) {
+ eecd |= E1000_EECD_CS; /* Pull CS high */
+ eecd &= ~E1000_EECD_SK; /* Lower SCK */
+
+ E1000_WRITE_REG(hw, EECD, eecd);
+
+ udelay(hw->eeprom.delay_usec);
+ } else if(hw->eeprom.type == e1000_eeprom_microwire) {
+ /* cleanup eeprom */
+
+ /* CS on Microwire is active-high */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);
+
+ E1000_WRITE_REG(hw, EECD, eecd);
+
+ /* Rising edge of clock */
+ eecd |= E1000_EECD_SK;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(hw->eeprom.delay_usec);
+
+ /* Falling edge of clock */
+ eecd &= ~E1000_EECD_SK;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(hw->eeprom.delay_usec);
}
- /* IGP01 PHY may advertise full duplex operation after speed downgrade even
- * if it is operating at half duplex. Here we set the duplex settings to
- * match the duplex in the link partner's capabilities.
- */
- if(hw->phy_type == e1000_phy_igp && hw->speed_downgraded) {
- ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data);
- if(ret_val)
- return ret_val;
-
- if(!(phy_data & NWAY_ER_LP_NWAY_CAPS))
- *duplex = HALF_DUPLEX;
- else {
- ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY, &phy_data);
- if(ret_val)
- return ret_val;
- if((*speed == SPEED_100 && !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) ||
- (*speed == SPEED_10 && !(phy_data & NWAY_LPAR_10T_FD_CAPS)))
- *duplex = HALF_DUPLEX;
- }
+ /* Stop requesting EEPROM access */
+ if(hw->mac_type > e1000_82544) {
+ eecd &= ~E1000_EECD_REQ;
+ E1000_WRITE_REG(hw, EECD, eecd);
}
- return E1000_SUCCESS;
+ e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
}
/******************************************************************************
-* Blocks until autoneg completes or times out (~4.5 seconds)
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
+ * Reads a 16 bit word from the EEPROM.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
int32_t
-e1000_wait_autoneg(struct e1000_hw *hw)
+e1000_spi_eeprom_ready(struct e1000_hw *hw)
{
- int32_t ret_val;
- uint16_t i;
- uint16_t phy_data;
-
- DEBUGFUNC("e1000_wait_autoneg");
- DEBUGOUT("Waiting for Auto-Neg to complete.\n");
+ uint16_t retry_count = 0;
+ uint8_t spi_stat_reg;
- /* We will wait for autoneg to complete or 4.5 seconds to expire. */
- for(i = PHY_AUTO_NEG_TIME; i > 0; i--) {
- /* Read the MII Status Register and wait for Auto-Neg
- * Complete bit to be set.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
- return ret_val;
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
- return ret_val;
- if(phy_data & MII_SR_AUTONEG_COMPLETE) {
- return E1000_SUCCESS;
- }
- msec_delay(100);
- }
- return E1000_SUCCESS;
-}
+ DEBUGFUNC("e1000_spi_eeprom_ready");
-/******************************************************************************
-* Raises the Management Data Clock
-*
-* hw - Struct containing variables accessed by shared code
-* ctrl - Device control register's current value
-******************************************************************************/
-static void
-e1000_raise_mdi_clk(struct e1000_hw *hw,
- uint32_t *ctrl)
-{
- /* Raise the clock input to the Management Data Clock (by setting the MDC
- * bit), and then delay 10 microseconds.
+ /* Read "Status Register" repeatedly until the LSB is cleared. The
+ * EEPROM will signal that the command has been completed by clearing
+ * bit 0 of the internal status register. If it's not cleared within
+ * 5 milliseconds, then error out.
*/
- E1000_WRITE_REG(hw, CTRL, (*ctrl | E1000_CTRL_MDC));
- E1000_WRITE_FLUSH(hw);
- udelay(10);
-}
+ retry_count = 0;
+ do {
+ e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI,
+ hw->eeprom.opcode_bits);
+ spi_stat_reg = (uint8_t)e1000_shift_in_ee_bits(hw, 8);
+ if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI))
+ break;
-/******************************************************************************
-* Lowers the Management Data Clock
-*
-* hw - Struct containing variables accessed by shared code
-* ctrl - Device control register's current value
-******************************************************************************/
-static void
-e1000_lower_mdi_clk(struct e1000_hw *hw,
- uint32_t *ctrl)
-{
- /* Lower the clock input to the Management Data Clock (by clearing the MDC
- * bit), and then delay 10 microseconds.
- */
- E1000_WRITE_REG(hw, CTRL, (*ctrl & ~E1000_CTRL_MDC));
- E1000_WRITE_FLUSH(hw);
- udelay(10);
-}
+ udelay(5);
+ retry_count += 5;
-/******************************************************************************
-* Shifts data bits out to the PHY
-*
-* hw - Struct containing variables accessed by shared code
-* data - Data to send out to the PHY
-* count - Number of bits to shift out
-*
-* Bits are shifted out in MSB to LSB order.
-******************************************************************************/
-static void
-e1000_shift_out_mdi_bits(struct e1000_hw *hw,
- uint32_t data,
- uint16_t count)
-{
- uint32_t ctrl;
- uint32_t mask;
+ e1000_standby_eeprom(hw);
+ } while(retry_count < EEPROM_MAX_RETRY_SPI);
- /* We need to shift "count" number of bits out to the PHY. So, the value
- * in the "data" parameter will be shifted out to the PHY one bit at a
- * time. In order to do this, "data" must be broken down into bits.
+ /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and
+ * only 0-5mSec on 5V devices)
*/
- mask = 0x01;
- mask <<= (count - 1);
-
- ctrl = E1000_READ_REG(hw, CTRL);
+ if(retry_count >= EEPROM_MAX_RETRY_SPI) {
+ DEBUGOUT("SPI EEPROM Status error\n");
+ return -E1000_ERR_EEPROM;
+ }
- /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */
- ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR);
+ return E1000_SUCCESS;
+}
- while(mask) {
- /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and
- * then raising and lowering the Management Data Clock. A "0" is
- * shifted out to the PHY by setting the MDIO bit to "0" and then
- * raising and lowering the clock.
- */
- if(data & mask) ctrl |= E1000_CTRL_MDIO;
- else ctrl &= ~E1000_CTRL_MDIO;
+/******************************************************************************
+ * Reads a 16 bit word from the EEPROM.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to read
+ * data - word read from the EEPROM
+ * words - number of words to read
+ *****************************************************************************/
+int32_t
+e1000_read_eeprom(struct e1000_hw *hw,
+ uint16_t offset,
+ uint16_t words,
+ uint16_t *data)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ uint32_t i = 0;
+ int32_t ret_val;
- E1000_WRITE_REG(hw, CTRL, ctrl);
- E1000_WRITE_FLUSH(hw);
+ DEBUGFUNC("e1000_read_eeprom");
- udelay(10);
+ /* A check for invalid values: offset too large, too many words, and not
+ * enough words.
+ */
+ if((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) ||
+ (words == 0)) {
+ DEBUGOUT("\"words\" parameter out of bounds\n");
+ return -E1000_ERR_EEPROM;
+ }
- e1000_raise_mdi_clk(hw, &ctrl);
- e1000_lower_mdi_clk(hw, &ctrl);
+ /* FLASH reads without acquiring the semaphore are safe */
+ if (e1000_is_onboard_nvm_eeprom(hw) == TRUE &&
+ hw->eeprom.use_eerd == FALSE) {
+ switch (hw->mac_type) {
+ case e1000_80003es2lan:
+ break;
+ default:
+ /* Prepare the EEPROM for reading */
+ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+ break;
+ }
+ }
- mask = mask >> 1;
+ if (eeprom->use_eerd == TRUE) {
+ ret_val = e1000_read_eeprom_eerd(hw, offset, words, data);
+ if ((e1000_is_onboard_nvm_eeprom(hw) == TRUE) ||
+ (hw->mac_type != e1000_82573))
+ e1000_release_eeprom(hw);
+ return ret_val;
}
-}
-/******************************************************************************
-* Shifts data bits in from the PHY
-*
-* hw - Struct containing variables accessed by shared code
-*
-* Bits are shifted in in MSB to LSB order.
-******************************************************************************/
-static uint16_t
-e1000_shift_in_mdi_bits(struct e1000_hw *hw)
-{
- uint32_t ctrl;
- uint16_t data = 0;
- uint8_t i;
+ if(eeprom->type == e1000_eeprom_spi) {
+ uint16_t word_in;
+ uint8_t read_opcode = EEPROM_READ_OPCODE_SPI;
- /* In order to read a register from the PHY, we need to shift in a total
- * of 18 bits from the PHY. The first two bit (turnaround) times are used
- * to avoid contention on the MDIO pin when a read operation is performed.
- * These two bits are ignored by us and thrown away. Bits are "shifted in"
- * by raising the input to the Management Data Clock (setting the MDC bit),
- * and then reading the value of the MDIO bit.
- */
- ctrl = E1000_READ_REG(hw, CTRL);
+ if(e1000_spi_eeprom_ready(hw)) {
+ e1000_release_eeprom(hw);
+ return -E1000_ERR_EEPROM;
+ }
- /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */
- ctrl &= ~E1000_CTRL_MDIO_DIR;
- ctrl &= ~E1000_CTRL_MDIO;
+ e1000_standby_eeprom(hw);
- E1000_WRITE_REG(hw, CTRL, ctrl);
- E1000_WRITE_FLUSH(hw);
+ /* Some SPI eeproms use the 8th address bit embedded in the opcode */
+ if((eeprom->address_bits == 8) && (offset >= 128))
+ read_opcode |= EEPROM_A8_OPCODE_SPI;
- /* Raise and Lower the clock before reading in the data. This accounts for
- * the turnaround bits. The first clock occurred when we clocked out the
- * last bit of the Register Address.
- */
- e1000_raise_mdi_clk(hw, &ctrl);
- e1000_lower_mdi_clk(hw, &ctrl);
+ /* Send the READ command (opcode + addr) */
+ e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits);
+ e1000_shift_out_ee_bits(hw, (uint16_t)(offset*2), eeprom->address_bits);
- for(data = 0, i = 0; i < 16; i++) {
- data = data << 1;
- e1000_raise_mdi_clk(hw, &ctrl);
- ctrl = E1000_READ_REG(hw, CTRL);
- /* Check to see if we shifted in a "1". */
- if(ctrl & E1000_CTRL_MDIO) data |= 1;
- e1000_lower_mdi_clk(hw, &ctrl);
+ /* Read the data. The address of the eeprom internally increments with
+ * each byte (spi) being read, saving on the overhead of eeprom setup
+ * and tear-down. The address counter will roll over if reading beyond
+ * the size of the eeprom, thus allowing the entire memory to be read
+ * starting from any offset. */
+ for (i = 0; i < words; i++) {
+ word_in = e1000_shift_in_ee_bits(hw, 16);
+ data[i] = (word_in >> 8) | (word_in << 8);
+ }
+ } else if(eeprom->type == e1000_eeprom_microwire) {
+ for (i = 0; i < words; i++) {
+ /* Send the READ command (opcode + addr) */
+ e1000_shift_out_ee_bits(hw, EEPROM_READ_OPCODE_MICROWIRE,
+ eeprom->opcode_bits);
+ e1000_shift_out_ee_bits(hw, (uint16_t)(offset + i),
+ eeprom->address_bits);
+
+ /* Read the data. For microwire, each word requires the overhead
+ * of eeprom setup and tear-down. */
+ data[i] = e1000_shift_in_ee_bits(hw, 16);
+ e1000_standby_eeprom(hw);
+ }
}
- e1000_raise_mdi_clk(hw, &ctrl);
- e1000_lower_mdi_clk(hw, &ctrl);
+ /* End this read operation */
+ e1000_release_eeprom(hw);
- return data;
+ return E1000_SUCCESS;
}
-/*****************************************************************************
-* Reads the value from a PHY register, if the value is on a specific non zero
-* page, sets the page first.
-* hw - Struct containing variables accessed by shared code
-* reg_addr - address of the PHY register to read
-******************************************************************************/
-int32_t
-e1000_read_phy_reg(struct e1000_hw *hw,
- uint32_t reg_addr,
- uint16_t *phy_data)
+/******************************************************************************
+ * Reads a 16 bit word from the EEPROM using the EERD register.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to read
+ * data - word read from the EEPROM
+ * words - number of words to read
+ *****************************************************************************/
+static int32_t
+e1000_read_eeprom_eerd(struct e1000_hw *hw,
+ uint16_t offset,
+ uint16_t words,
+ uint16_t *data)
{
- uint32_t ret_val;
+ uint32_t i, eerd = 0;
+ int32_t error = 0;
- DEBUGFUNC("e1000_read_phy_reg");
+ for (i = 0; i < words; i++) {
+ eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) +
+ E1000_EEPROM_RW_REG_START;
- if(hw->phy_type == e1000_phy_igp &&
- (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
- ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
- (uint16_t)reg_addr);
- if(ret_val)
- return ret_val;
+ E1000_WRITE_REG(hw, EERD, eerd);
+ error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ);
+
+ if(error) {
+ break;
+ }
+ data[i] = (E1000_READ_REG(hw, EERD) >> E1000_EEPROM_RW_REG_DATA);
+
}
-
- ret_val = e1000_read_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT & reg_addr,
- phy_data);
-
- return ret_val;
+
+ return error;
}
-int32_t
-e1000_read_phy_reg_ex(struct e1000_hw *hw,
- uint32_t reg_addr,
- uint16_t *phy_data)
+/******************************************************************************
+ * Writes a 16 bit word from the EEPROM using the EEWR register.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to read
+ * data - word read from the EEPROM
+ * words - number of words to read
+ *****************************************************************************/
+static int32_t
+e1000_write_eeprom_eewr(struct e1000_hw *hw,
+ uint16_t offset,
+ uint16_t words,
+ uint16_t *data)
{
- uint32_t i;
- uint32_t mdic = 0;
- const uint32_t phy_addr = 1;
+ uint32_t register_value = 0;
+ uint32_t i = 0;
+ int32_t error = 0;
- DEBUGFUNC("e1000_read_phy_reg_ex");
+ if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM))
+ return -E1000_ERR_SWFW_SYNC;
- if(reg_addr > MAX_PHY_REG_ADDRESS) {
- DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
- return -E1000_ERR_PARAM;
- }
+ for (i = 0; i < words; i++) {
+ register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) |
+ ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) |
+ E1000_EEPROM_RW_REG_START;
- if(hw->mac_type > e1000_82543) {
- /* Set up Op-code, Phy Address, and register address in the MDI
- * Control register. The MAC will take care of interfacing with the
- * PHY to retrieve the desired data.
- */
- mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
- (phy_addr << E1000_MDIC_PHY_SHIFT) |
- (E1000_MDIC_OP_READ));
+ error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE);
+ if(error) {
+ break;
+ }
- E1000_WRITE_REG(hw, MDIC, mdic);
+ E1000_WRITE_REG(hw, EEWR, register_value);
+
+ error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE);
+
+ if(error) {
+ break;
+ }
+ }
+
+ e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
+ return error;
+}
- /* Poll the ready bit to see if the MDI read completed */
- for(i = 0; i < 64; i++) {
- udelay(50);
- mdic = E1000_READ_REG(hw, MDIC);
- if(mdic & E1000_MDIC_READY) break;
- }
- if(!(mdic & E1000_MDIC_READY)) {
- DEBUGOUT("MDI Read did not complete\n");
- return -E1000_ERR_PHY;
- }
- if(mdic & E1000_MDIC_ERROR) {
- DEBUGOUT("MDI Error\n");
- return -E1000_ERR_PHY;
+/******************************************************************************
+ * Polls the status bit (bit 1) of the EERD to determine when the read is done.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static int32_t
+e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd)
+{
+ uint32_t attempts = 100000;
+ uint32_t i, reg = 0;
+ int32_t done = E1000_ERR_EEPROM;
+
+ for(i = 0; i < attempts; i++) {
+ if(eerd == E1000_EEPROM_POLL_READ)
+ reg = E1000_READ_REG(hw, EERD);
+ else
+ reg = E1000_READ_REG(hw, EEWR);
+
+ if(reg & E1000_EEPROM_RW_REG_DONE) {
+ done = E1000_SUCCESS;
+ break;
}
- *phy_data = (uint16_t) mdic;
- } else {
- /* We must first send a preamble through the MDIO pin to signal the
- * beginning of an MII instruction. This is done by sending 32
- * consecutive "1" bits.
- */
- e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
-
- /* Now combine the next few fields that are required for a read
- * operation. We use this method instead of calling the
- * e1000_shift_out_mdi_bits routine five different times. The format of
- * a MII read instruction consists of a shift out of 14 bits and is
- * defined as follows:
- * <Preamble><SOF><Op Code><Phy Addr><Reg Addr>
- * followed by a shift in of 18 bits. This first two bits shifted in
- * are TurnAround bits used to avoid contention on the MDIO pin when a
- * READ operation is performed. These two bits are thrown away
- * followed by a shift in of 16 bits which contains the desired data.
- */
- mdic = ((reg_addr) | (phy_addr << 5) |
- (PHY_OP_READ << 10) | (PHY_SOF << 12));
-
- e1000_shift_out_mdi_bits(hw, mdic, 14);
-
- /* Now that we've shifted out the read command to the MII, we need to
- * "shift in" the 16-bit value (18 total bits) of the requested PHY
- * register address.
- */
- *phy_data = e1000_shift_in_mdi_bits(hw);
+ udelay(5);
}
- return E1000_SUCCESS;
+
+ return done;
}
-/******************************************************************************
-* Writes a value to a PHY register
+/***************************************************************************
+* Description: Determines if the onboard NVM is FLASH or EEPROM.
*
* hw - Struct containing variables accessed by shared code
-* reg_addr - address of the PHY register to write
-* data - data to write to the PHY
-******************************************************************************/
-int32_t
-e1000_write_phy_reg(struct e1000_hw *hw,
- uint32_t reg_addr,
- uint16_t phy_data)
+****************************************************************************/
+static boolean_t
+e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw)
{
- uint32_t ret_val;
+ uint32_t eecd = 0;
- DEBUGFUNC("e1000_write_phy_reg");
+ DEBUGFUNC("e1000_is_onboard_nvm_eeprom");
- if(hw->phy_type == e1000_phy_igp &&
- (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
- ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
- (uint16_t)reg_addr);
- if(ret_val)
- return ret_val;
- }
+ if(hw->mac_type == e1000_82573) {
+ eecd = E1000_READ_REG(hw, EECD);
- ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT & reg_addr,
- phy_data);
+ /* Isolate bits 15 & 16 */
+ eecd = ((eecd >> 15) & 0x03);
- return ret_val;
+ /* If both bits are set, device is Flash type */
+ if(eecd == 0x03) {
+ return FALSE;
+ }
+ }
+ return TRUE;
}
+/******************************************************************************
+ * Verifies that the EEPROM has a valid checksum
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Reads the first 64 16 bit words of the EEPROM and sums the values read.
+ * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is
+ * valid.
+ *****************************************************************************/
int32_t
-e1000_write_phy_reg_ex(struct e1000_hw *hw,
- uint32_t reg_addr,
- uint16_t phy_data)
+e1000_validate_eeprom_checksum(struct e1000_hw *hw)
{
- uint32_t i;
- uint32_t mdic = 0;
- const uint32_t phy_addr = 1;
+ uint16_t checksum = 0;
+ uint16_t i, eeprom_data;
- DEBUGFUNC("e1000_write_phy_reg_ex");
+ DEBUGFUNC("e1000_validate_eeprom_checksum");
- if(reg_addr > MAX_PHY_REG_ADDRESS) {
- DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
- return -E1000_ERR_PARAM;
+ if ((hw->mac_type == e1000_82573) &&
+ (e1000_is_onboard_nvm_eeprom(hw) == FALSE)) {
+ /* Check bit 4 of word 10h. If it is 0, firmware is done updating
+ * 10h-12h. Checksum may need to be fixed. */
+ e1000_read_eeprom(hw, 0x10, 1, &eeprom_data);
+ if ((eeprom_data & 0x10) == 0) {
+ /* Read 0x23 and check bit 15. This bit is a 1 when the checksum
+ * has already been fixed. If the checksum is still wrong and this
+ * bit is a 1, we need to return bad checksum. Otherwise, we need
+ * to set this bit to a 1 and update the checksum. */
+ e1000_read_eeprom(hw, 0x23, 1, &eeprom_data);
+ if ((eeprom_data & 0x8000) == 0) {
+ eeprom_data |= 0x8000;
+ e1000_write_eeprom(hw, 0x23, 1, &eeprom_data);
+ e1000_update_eeprom_checksum(hw);
+ }
+ }
}
- if(hw->mac_type > e1000_82543) {
- /* Set up Op-code, Phy Address, register address, and data intended
- * for the PHY register in the MDI Control register. The MAC will take
- * care of interfacing with the PHY to send the desired data.
- */
- mdic = (((uint32_t) phy_data) |
- (reg_addr << E1000_MDIC_REG_SHIFT) |
- (phy_addr << E1000_MDIC_PHY_SHIFT) |
- (E1000_MDIC_OP_WRITE));
+ for(i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
+ if(e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ checksum += eeprom_data;
+ }
- E1000_WRITE_REG(hw, MDIC, mdic);
+ if(checksum == (uint16_t) EEPROM_SUM)
+ return E1000_SUCCESS;
+ else {
+ DEBUGOUT("EEPROM Checksum Invalid\n");
+ return -E1000_ERR_EEPROM;
+ }
+}
- /* Poll the ready bit to see if the MDI read completed */
- for(i = 0; i < 640; i++) {
- udelay(5);
- mdic = E1000_READ_REG(hw, MDIC);
- if(mdic & E1000_MDIC_READY) break;
- }
- if(!(mdic & E1000_MDIC_READY)) {
- DEBUGOUT("MDI Write did not complete\n");
- return -E1000_ERR_PHY;
- }
- } else {
- /* We'll need to use the SW defined pins to shift the write command
- * out to the PHY. We first send a preamble to the PHY to signal the
- * beginning of the MII instruction. This is done by sending 32
- * consecutive "1" bits.
- */
- e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
+/******************************************************************************
+ * Calculates the EEPROM checksum and writes it to the EEPROM
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Sums the first 63 16 bit words of the EEPROM. Subtracts the sum from 0xBABA.
+ * Writes the difference to word offset 63 of the EEPROM.
+ *****************************************************************************/
+int32_t
+e1000_update_eeprom_checksum(struct e1000_hw *hw)
+{
+ uint16_t checksum = 0;
+ uint16_t i, eeprom_data;
- /* Now combine the remaining required fields that will indicate a
- * write operation. We use this method instead of calling the
- * e1000_shift_out_mdi_bits routine for each field in the command. The
- * format of a MII write instruction is as follows:
- * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>.
- */
- mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) |
- (PHY_OP_WRITE << 12) | (PHY_SOF << 14));
- mdic <<= 16;
- mdic |= (uint32_t) phy_data;
+ DEBUGFUNC("e1000_update_eeprom_checksum");
- e1000_shift_out_mdi_bits(hw, mdic, 32);
+ for(i = 0; i < EEPROM_CHECKSUM_REG; i++) {
+ if(e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ checksum += eeprom_data;
+ }
+ checksum = (uint16_t) EEPROM_SUM - checksum;
+ if(e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) {
+ DEBUGOUT("EEPROM Write Error\n");
+ return -E1000_ERR_EEPROM;
+ } else if (hw->eeprom.type == e1000_eeprom_flash) {
+ e1000_commit_shadow_ram(hw);
}
-
return E1000_SUCCESS;
}
/******************************************************************************
-* Returns the PHY to the power-on reset state
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-void
-e1000_phy_hw_reset(struct e1000_hw *hw)
+ * Parent function for writing words to the different EEPROM types.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset within the EEPROM to be written to
+ * words - number of words to write
+ * data - 16 bit word to be written to the EEPROM
+ *
+ * If e1000_update_eeprom_checksum is not called after this function, the
+ * EEPROM will most likely contain an invalid checksum.
+ *****************************************************************************/
+int32_t
+e1000_write_eeprom(struct e1000_hw *hw,
+ uint16_t offset,
+ uint16_t words,
+ uint16_t *data)
{
- uint32_t ctrl, ctrl_ext;
- uint32_t led_ctrl;
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ int32_t status = 0;
- DEBUGFUNC("e1000_phy_hw_reset");
+ DEBUGFUNC("e1000_write_eeprom");
- DEBUGOUT("Resetting Phy...\n");
+ /* A check for invalid values: offset too large, too many words, and not
+ * enough words.
+ */
+ if((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) ||
+ (words == 0)) {
+ DEBUGOUT("\"words\" parameter out of bounds\n");
+ return -E1000_ERR_EEPROM;
+ }
- if(hw->mac_type > e1000_82543) {
- /* Read the device control register and assert the E1000_CTRL_PHY_RST
- * bit. Then, take it out of reset.
- */
- ctrl = E1000_READ_REG(hw, CTRL);
- E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST);
- E1000_WRITE_FLUSH(hw);
- msec_delay(10);
- E1000_WRITE_REG(hw, CTRL, ctrl);
- E1000_WRITE_FLUSH(hw);
+ /* 82573 writes only through eewr */
+ if(eeprom->use_eewr == TRUE)
+ return e1000_write_eeprom_eewr(hw, offset, words, data);
+
+ /* Prepare the EEPROM for writing */
+ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+
+ if(eeprom->type == e1000_eeprom_microwire) {
+ status = e1000_write_eeprom_microwire(hw, offset, words, data);
} else {
- /* Read the Extended Device Control Register, assert the PHY_RESET_DIR
- * bit to put the PHY into reset. Then, take it out of reset.
- */
- ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
- ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR;
- ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA;
- E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
- E1000_WRITE_FLUSH(hw);
+ status = e1000_write_eeprom_spi(hw, offset, words, data);
msec_delay(10);
- ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA;
- E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
- E1000_WRITE_FLUSH(hw);
}
- udelay(150);
- if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
- /* Configure activity LED after PHY reset */
- led_ctrl = E1000_READ_REG(hw, LEDCTL);
- led_ctrl &= IGP_ACTIVITY_LED_MASK;
- led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
- E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
- }
+ /* Done with writing */
+ e1000_release_eeprom(hw);
+
+ return status;
}
/******************************************************************************
-* Resets the PHY
-*
-* hw - Struct containing variables accessed by shared code
-*
-* Sets bit 15 of the MII Control regiser
-******************************************************************************/
+ * Writes a 16 bit word to a given offset in an SPI EEPROM.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset within the EEPROM to be written to
+ * words - number of words to write
+ * data - pointer to array of 8 bit words to be written to the EEPROM
+ *
+ *****************************************************************************/
int32_t
-e1000_phy_reset(struct e1000_hw *hw)
+e1000_write_eeprom_spi(struct e1000_hw *hw,
+ uint16_t offset,
+ uint16_t words,
+ uint16_t *data)
{
- int32_t ret_val;
- uint16_t phy_data;
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ uint16_t widx = 0;
- DEBUGFUNC("e1000_phy_reset");
+ DEBUGFUNC("e1000_write_eeprom_spi");
- if(hw->mac_type != e1000_82541_rev_2) {
- ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
- if(ret_val)
- return ret_val;
+ while (widx < words) {
+ uint8_t write_opcode = EEPROM_WRITE_OPCODE_SPI;
- phy_data |= MII_CR_RESET;
- ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
- if(ret_val)
- return ret_val;
+ if(e1000_spi_eeprom_ready(hw)) return -E1000_ERR_EEPROM;
- udelay(1);
- } else e1000_phy_hw_reset(hw);
+ e1000_standby_eeprom(hw);
- if(hw->phy_type == e1000_phy_igp)
- e1000_phy_init_script(hw);
+ /* Send the WRITE ENABLE command (8 bit opcode ) */
+ e1000_shift_out_ee_bits(hw, EEPROM_WREN_OPCODE_SPI,
+ eeprom->opcode_bits);
+
+ e1000_standby_eeprom(hw);
+
+ /* Some SPI eeproms use the 8th address bit embedded in the opcode */
+ if((eeprom->address_bits == 8) && (offset >= 128))
+ write_opcode |= EEPROM_A8_OPCODE_SPI;
+
+ /* Send the Write command (8-bit opcode + addr) */
+ e1000_shift_out_ee_bits(hw, write_opcode, eeprom->opcode_bits);
+
+ e1000_shift_out_ee_bits(hw, (uint16_t)((offset + widx)*2),
+ eeprom->address_bits);
+
+ /* Send the data */
+
+ /* Loop to allow for up to whole page write (32 bytes) of eeprom */
+ while (widx < words) {
+ uint16_t word_out = data[widx];
+ word_out = (word_out >> 8) | (word_out << 8);
+ e1000_shift_out_ee_bits(hw, word_out, 16);
+ widx++;
+
+ /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE
+ * operation, while the smaller eeproms are capable of an 8-byte
+ * PAGE WRITE operation. Break the inner loop to pass new address
+ */
+ if((((offset + widx)*2) % eeprom->page_size) == 0) {
+ e1000_standby_eeprom(hw);
+ break;
+ }
+ }
+ }
return E1000_SUCCESS;
}
/******************************************************************************
-* Probes the expected PHY address for known PHY IDs
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
+ * Writes a 16 bit word to a given offset in a Microwire EEPROM.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset within the EEPROM to be written to
+ * words - number of words to write
+ * data - pointer to array of 16 bit words to be written to the EEPROM
+ *
+ *****************************************************************************/
int32_t
-e1000_detect_gig_phy(struct e1000_hw *hw)
+e1000_write_eeprom_microwire(struct e1000_hw *hw,
+ uint16_t offset,
+ uint16_t words,
+ uint16_t *data)
{
- int32_t phy_init_status, ret_val;
- uint16_t phy_id_high, phy_id_low;
- boolean_t match = FALSE;
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ uint32_t eecd;
+ uint16_t words_written = 0;
+ uint16_t i = 0;
- DEBUGFUNC("e1000_detect_gig_phy");
+ DEBUGFUNC("e1000_write_eeprom_microwire");
- /* Read the PHY ID Registers to identify which PHY is onboard. */
- ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
- if(ret_val)
- return ret_val;
+ /* Send the write enable command to the EEPROM (3-bit opcode plus
+ * 6/8-bit dummy address beginning with 11). It's less work to include
+ * the 11 of the dummy address as part of the opcode than it is to shift
+ * it over the correct number of bits for the address. This puts the
+ * EEPROM into write/erase mode.
+ */
+ e1000_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE_MICROWIRE,
+ (uint16_t)(eeprom->opcode_bits + 2));
- hw->phy_id = (uint32_t) (phy_id_high << 16);
- udelay(20);
- ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low);
- if(ret_val)
- return ret_val;
+ e1000_shift_out_ee_bits(hw, 0, (uint16_t)(eeprom->address_bits - 2));
- hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK);
- hw->phy_revision = (uint32_t) phy_id_low & ~PHY_REVISION_MASK;
+ /* Prepare the EEPROM */
+ e1000_standby_eeprom(hw);
- switch(hw->mac_type) {
- case e1000_82543:
- if(hw->phy_id == M88E1000_E_PHY_ID) match = TRUE;
- break;
- case e1000_82544:
- if(hw->phy_id == M88E1000_I_PHY_ID) match = TRUE;
- break;
- case e1000_82540:
- case e1000_82545:
- case e1000_82545_rev_3:
- case e1000_82546:
- case e1000_82546_rev_3:
- if(hw->phy_id == M88E1011_I_PHY_ID) match = TRUE;
- break;
- case e1000_82541:
- case e1000_82541_rev_2:
- case e1000_82547:
- case e1000_82547_rev_2:
- if(hw->phy_id == IGP01E1000_I_PHY_ID) match = TRUE;
- break;
- default:
- DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
- return -E1000_ERR_CONFIG;
- }
- phy_init_status = e1000_set_phy_type(hw);
+ while (words_written < words) {
+ /* Send the Write command (3-bit opcode + addr) */
+ e1000_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE_MICROWIRE,
+ eeprom->opcode_bits);
+
+ e1000_shift_out_ee_bits(hw, (uint16_t)(offset + words_written),
+ eeprom->address_bits);
+
+ /* Send the data */
+ e1000_shift_out_ee_bits(hw, data[words_written], 16);
+
+ /* Toggle the CS line. This in effect tells the EEPROM to execute
+ * the previous command.
+ */
+ e1000_standby_eeprom(hw);
+
+ /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will
+ * signal that the command has been completed by raising the DO signal.
+ * If DO does not go high in 10 milliseconds, then error out.
+ */
+ for(i = 0; i < 200; i++) {
+ eecd = E1000_READ_REG(hw, EECD);
+ if(eecd & E1000_EECD_DO) break;
+ udelay(50);
+ }
+ if(i == 200) {
+ DEBUGOUT("EEPROM Write did not complete\n");
+ return -E1000_ERR_EEPROM;
+ }
- if ((match) && (phy_init_status == E1000_SUCCESS)) {
- DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id);
- return E1000_SUCCESS;
+ /* Recover from write */
+ e1000_standby_eeprom(hw);
+
+ words_written++;
}
- DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id);
- return -E1000_ERR_PHY;
-}
-/******************************************************************************
-* Resets the PHY's DSP
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-static int32_t
-e1000_phy_reset_dsp(struct e1000_hw *hw)
-{
- int32_t ret_val;
- DEBUGFUNC("e1000_phy_reset_dsp");
+ /* Send the write disable command to the EEPROM (3-bit opcode plus
+ * 6/8-bit dummy address beginning with 10). It's less work to include
+ * the 10 of the dummy address as part of the opcode than it is to shift
+ * it over the correct number of bits for the address. This takes the
+ * EEPROM out of write/erase mode.
+ */
+ e1000_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE_MICROWIRE,
+ (uint16_t)(eeprom->opcode_bits + 2));
- do {
- ret_val = e1000_write_phy_reg(hw, 29, 0x001d);
- if(ret_val) break;
- ret_val = e1000_write_phy_reg(hw, 30, 0x00c1);
- if(ret_val) break;
- ret_val = e1000_write_phy_reg(hw, 30, 0x0000);
- if(ret_val) break;
- ret_val = E1000_SUCCESS;
- } while(0);
+ e1000_shift_out_ee_bits(hw, 0, (uint16_t)(eeprom->address_bits - 2));
- return ret_val;
+ return E1000_SUCCESS;
}
/******************************************************************************
-* Get PHY information from various PHY registers for igp PHY only.
-*
-* hw - Struct containing variables accessed by shared code
-* phy_info - PHY information structure
-******************************************************************************/
-int32_t
-e1000_phy_igp_get_info(struct e1000_hw *hw,
- struct e1000_phy_info *phy_info)
+ * Flushes the cached eeprom to NVM. This is done by saving the modified values
+ * in the eeprom cache and the non modified values in the currently active bank
+ * to the new bank.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to read
+ * data - word read from the EEPROM
+ * words - number of words to read
+ *****************************************************************************/
+static int32_t
+e1000_commit_shadow_ram(struct e1000_hw *hw)
{
- int32_t ret_val;
- uint16_t phy_data, polarity, min_length, max_length, average;
-
- DEBUGFUNC("e1000_phy_igp_get_info");
+ uint32_t attempts = 100000;
+ uint32_t eecd = 0;
+ uint32_t flop = 0;
+ uint32_t i = 0;
+ int32_t error = E1000_SUCCESS;
- /* The downshift status is checked only once, after link is established,
- * and it stored in the hw->speed_downgraded parameter. */
- phy_info->downshift = hw->speed_downgraded;
+ /* The flop register will be used to determine if flash type is STM */
+ flop = E1000_READ_REG(hw, FLOP);
- /* IGP01E1000 does not need to support it. */
- phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal;
+ if (hw->mac_type == e1000_82573) {
+ for (i=0; i < attempts; i++) {
+ eecd = E1000_READ_REG(hw, EECD);
+ if ((eecd & E1000_EECD_FLUPD) == 0) {
+ break;
+ }
+ udelay(5);
+ }
- /* IGP01E1000 always correct polarity reversal */
- phy_info->polarity_correction = e1000_polarity_reversal_enabled;
+ if (i == attempts) {
+ return -E1000_ERR_EEPROM;
+ }
- /* Check polarity status */
- ret_val = e1000_check_polarity(hw, &polarity);
- if(ret_val)
- return ret_val;
+ /* If STM opcode located in bits 15:8 of flop, reset firmware */
+ if ((flop & 0xFF00) == E1000_STM_OPCODE) {
+ E1000_WRITE_REG(hw, HICR, E1000_HICR_FW_RESET);
+ }
- phy_info->cable_polarity = polarity;
+ /* Perform the flash update */
+ E1000_WRITE_REG(hw, EECD, eecd | E1000_EECD_FLUPD);
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, &phy_data);
- if(ret_val)
- return ret_val;
+ for (i=0; i < attempts; i++) {
+ eecd = E1000_READ_REG(hw, EECD);
+ if ((eecd & E1000_EECD_FLUPD) == 0) {
+ break;
+ }
+ udelay(5);
+ }
- phy_info->mdix_mode = (phy_data & IGP01E1000_PSSR_MDIX) >>
- IGP01E1000_PSSR_MDIX_SHIFT;
+ if (i == attempts) {
+ return -E1000_ERR_EEPROM;
+ }
+ }
- if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
- IGP01E1000_PSSR_SPEED_1000MBPS) {
- /* Local/Remote Receiver Information are only valid at 1000 Mbps */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
- if(ret_val)
- return ret_val;
+ return error;
+}
- phy_info->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS) >>
- SR_1000T_LOCAL_RX_STATUS_SHIFT;
- phy_info->remote_rx = (phy_data & SR_1000T_REMOTE_RX_STATUS) >>
- SR_1000T_REMOTE_RX_STATUS_SHIFT;
+/******************************************************************************
+ * Reads the adapter's part number from the EEPROM
+ *
+ * hw - Struct containing variables accessed by shared code
+ * part_num - Adapter's part number
+ *****************************************************************************/
+int32_t
+e1000_read_part_num(struct e1000_hw *hw,
+ uint32_t *part_num)
+{
+ uint16_t offset = EEPROM_PBA_BYTE_1;
+ uint16_t eeprom_data;
- /* Get cable length */
- ret_val = e1000_get_cable_length(hw, &min_length, &max_length);
- if(ret_val)
- return ret_val;
+ DEBUGFUNC("e1000_read_part_num");
- /* transalte to old method */
- average = (max_length + min_length) / 2;
+ /* Get word 0 from EEPROM */
+ if(e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ /* Save word 0 in upper half of part_num */
+ *part_num = (uint32_t) (eeprom_data << 16);
- if(average <= e1000_igp_cable_length_50)
- phy_info->cable_length = e1000_cable_length_50;
- else if(average <= e1000_igp_cable_length_80)
- phy_info->cable_length = e1000_cable_length_50_80;
- else if(average <= e1000_igp_cable_length_110)
- phy_info->cable_length = e1000_cable_length_80_110;
- else if(average <= e1000_igp_cable_length_140)
- phy_info->cable_length = e1000_cable_length_110_140;
- else
- phy_info->cable_length = e1000_cable_length_140;
+ /* Get word 1 from EEPROM */
+ if(e1000_read_eeprom(hw, ++offset, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
}
+ /* Save word 1 in lower half of part_num */
+ *part_num |= eeprom_data;
return E1000_SUCCESS;
}
/******************************************************************************
-* Get PHY information from various PHY registers fot m88 PHY only.
-*
-* hw - Struct containing variables accessed by shared code
-* phy_info - PHY information structure
-******************************************************************************/
+ * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
+ * second function of dual function devices
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
int32_t
-e1000_phy_m88_get_info(struct e1000_hw *hw,
- struct e1000_phy_info *phy_info)
+e1000_read_mac_addr(struct e1000_hw * hw)
{
- int32_t ret_val;
- uint16_t phy_data, polarity;
-
- DEBUGFUNC("e1000_phy_m88_get_info");
-
- /* The downshift status is checked only once, after link is established,
- * and it stored in the hw->speed_downgraded parameter. */
- phy_info->downshift = hw->speed_downgraded;
+ uint16_t offset;
+ uint16_t eeprom_data, i;
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
- if(ret_val)
- return ret_val;
+ DEBUGFUNC("e1000_read_mac_addr");
- phy_info->extended_10bt_distance =
- (phy_data & M88E1000_PSCR_10BT_EXT_DIST_ENABLE) >>
- M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT;
- phy_info->polarity_correction =
- (phy_data & M88E1000_PSCR_POLARITY_REVERSAL) >>
- M88E1000_PSCR_POLARITY_REVERSAL_SHIFT;
+ for(i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
+ offset = i >> 1;
+ if(e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ hw->perm_mac_addr[i] = (uint8_t) (eeprom_data & 0x00FF);
+ hw->perm_mac_addr[i+1] = (uint8_t) (eeprom_data >> 8);
+ }
- /* Check polarity status */
- ret_val = e1000_check_polarity(hw, &polarity);
- if(ret_val)
- return ret_val;
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ case e1000_82571:
+ case e1000_80003es2lan:
+ if(E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)
+ hw->perm_mac_addr[5] ^= 0x01;
+ break;
+ }
- phy_info->cable_polarity = polarity;
+ for(i = 0; i < NODE_ADDRESS_SIZE; i++)
+ hw->mac_addr[i] = hw->perm_mac_addr[i];
+ return E1000_SUCCESS;
+}
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
- if(ret_val)
- return ret_val;
+/******************************************************************************
+ * Initializes receive address filters.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Places the MAC address in receive address register 0 and clears the rest
+ * of the receive addresss registers. Clears the multicast table. Assumes
+ * the receiver is in reset when the routine is called.
+ *****************************************************************************/
+static void
+e1000_init_rx_addrs(struct e1000_hw *hw)
+{
+ uint32_t i;
+ uint32_t rar_num;
- phy_info->mdix_mode = (phy_data & M88E1000_PSSR_MDIX) >>
- M88E1000_PSSR_MDIX_SHIFT;
+ DEBUGFUNC("e1000_init_rx_addrs");
- if(phy_data & M88E1000_PSSR_1000MBS) {
- /* Cable Length Estimation and Local/Remote Receiver Informatoion
- * are only valid at 1000 Mbps
- */
- phy_info->cable_length = ((phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
- M88E1000_PSSR_CABLE_LENGTH_SHIFT);
+ /* Setup the receive address. */
+ DEBUGOUT("Programming MAC Address into RAR[0]\n");
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
- if(ret_val)
- return ret_val;
+ e1000_rar_set(hw, hw->mac_addr, 0);
- phy_info->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS) >>
- SR_1000T_LOCAL_RX_STATUS_SHIFT;
+ rar_num = E1000_RAR_ENTRIES;
- phy_info->remote_rx = (phy_data & SR_1000T_REMOTE_RX_STATUS) >>
- SR_1000T_REMOTE_RX_STATUS_SHIFT;
+ /* Reserve a spot for the Locally Administered Address to work around
+ * an 82571 issue in which a reset on one port will reload the MAC on
+ * the other port. */
+ if ((hw->mac_type == e1000_82571) && (hw->laa_is_present == TRUE))
+ rar_num -= 1;
+ /* Zero out the other 15 receive addresses. */
+ DEBUGOUT("Clearing RAR[1-15]\n");
+ for(i = 1; i < rar_num; i++) {
+ E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
+ E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
}
-
- return E1000_SUCCESS;
}
+#if 0
/******************************************************************************
-* Get PHY information from various PHY registers
-*
-* hw - Struct containing variables accessed by shared code
-* phy_info - PHY information structure
-******************************************************************************/
-int32_t
-e1000_phy_get_info(struct e1000_hw *hw,
- struct e1000_phy_info *phy_info)
+ * Updates the MAC's list of multicast addresses.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * mc_addr_list - the list of new multicast addresses
+ * mc_addr_count - number of addresses
+ * pad - number of bytes between addresses in the list
+ * rar_used_count - offset where to start adding mc addresses into the RAR's
+ *
+ * The given list replaces any existing list. Clears the last 15 receive
+ * address registers and the multicast table. Uses receive address registers
+ * for the first 15 multicast addresses, and hashes the rest into the
+ * multicast table.
+ *****************************************************************************/
+void
+e1000_mc_addr_list_update(struct e1000_hw *hw,
+ uint8_t *mc_addr_list,
+ uint32_t mc_addr_count,
+ uint32_t pad,
+ uint32_t rar_used_count)
{
- int32_t ret_val;
- uint16_t phy_data;
+ uint32_t hash_value;
+ uint32_t i;
+ uint32_t num_rar_entry;
+ uint32_t num_mta_entry;
+
+ DEBUGFUNC("e1000_mc_addr_list_update");
- DEBUGFUNC("e1000_phy_get_info");
+ /* Set the new number of MC addresses that we are being requested to use. */
+ hw->num_mc_addrs = mc_addr_count;
- phy_info->cable_length = e1000_cable_length_undefined;
- phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_undefined;
- phy_info->cable_polarity = e1000_rev_polarity_undefined;
- phy_info->downshift = e1000_downshift_undefined;
- phy_info->polarity_correction = e1000_polarity_reversal_undefined;
- phy_info->mdix_mode = e1000_auto_x_mode_undefined;
- phy_info->local_rx = e1000_1000t_rx_status_undefined;
- phy_info->remote_rx = e1000_1000t_rx_status_undefined;
+ /* Clear RAR[1-15] */
+ DEBUGOUT(" Clearing RAR[1-15]\n");
+ num_rar_entry = E1000_RAR_ENTRIES;
+ /* Reserve a spot for the Locally Administered Address to work around
+ * an 82571 issue in which a reset on one port will reload the MAC on
+ * the other port. */
+ if ((hw->mac_type == e1000_82571) && (hw->laa_is_present == TRUE))
+ num_rar_entry -= 1;
+
+ for(i = rar_used_count; i < num_rar_entry; i++) {
+ E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
+ E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
+ }
- if(hw->media_type != e1000_media_type_copper) {
- DEBUGOUT("PHY info is only valid for copper media\n");
- return -E1000_ERR_CONFIG;
+ /* Clear the MTA */
+ DEBUGOUT(" Clearing MTA\n");
+ num_mta_entry = E1000_NUM_MTA_REGISTERS;
+ for(i = 0; i < num_mta_entry; i++) {
+ E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
}
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
- return ret_val;
+ /* Add the new addresses */
+ for(i = 0; i < mc_addr_count; i++) {
+ DEBUGOUT(" Adding the multicast addresses:\n");
+ DEBUGOUT7(" MC Addr #%d =%.2X %.2X %.2X %.2X %.2X %.2X\n", i,
+ mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad)],
+ mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 1],
+ mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 2],
+ mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 3],
+ mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 4],
+ mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 5]);
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
- return ret_val;
+ hash_value = e1000_hash_mc_addr(hw,
+ mc_addr_list +
+ (i * (ETH_LENGTH_OF_ADDRESS + pad)));
- if((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) {
- DEBUGOUT("PHY info is only valid if link is up\n");
- return -E1000_ERR_CONFIG;
- }
+ DEBUGOUT1(" Hash value = 0x%03X\n", hash_value);
- if(hw->phy_type == e1000_phy_igp)
- return e1000_phy_igp_get_info(hw, phy_info);
- else
- return e1000_phy_m88_get_info(hw, phy_info);
+ /* Place this multicast address in the RAR if there is room, *
+ * else put it in the MTA
+ */
+ if (rar_used_count < num_rar_entry) {
+ e1000_rar_set(hw,
+ mc_addr_list + (i * (ETH_LENGTH_OF_ADDRESS + pad)),
+ rar_used_count);
+ rar_used_count++;
+ } else {
+ e1000_mta_set(hw, hash_value);
+ }
+ }
+ DEBUGOUT("MC Update Complete\n");
}
+#endif /* 0 */
-int32_t
-e1000_validate_mdi_setting(struct e1000_hw *hw)
+/******************************************************************************
+ * Hashes an address to determine its location in the multicast table
+ *
+ * hw - Struct containing variables accessed by shared code
+ * mc_addr - the multicast address to hash
+ *****************************************************************************/
+uint32_t
+e1000_hash_mc_addr(struct e1000_hw *hw,
+ uint8_t *mc_addr)
{
- DEBUGFUNC("e1000_validate_mdi_settings");
+ uint32_t hash_value = 0;
- if(!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) {
- DEBUGOUT("Invalid MDI setting detected\n");
- hw->mdix = 1;
- return -E1000_ERR_CONFIG;
+ /* The portion of the address that is used for the hash table is
+ * determined by the mc_filter_type setting.
+ */
+ switch (hw->mc_filter_type) {
+ /* [0] [1] [2] [3] [4] [5]
+ * 01 AA 00 12 34 56
+ * LSB MSB
+ */
+ case 0:
+ /* [47:36] i.e. 0x563 for above example address */
+ hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4));
+ break;
+ case 1:
+ /* [46:35] i.e. 0xAC6 for above example address */
+ hash_value = ((mc_addr[4] >> 3) | (((uint16_t) mc_addr[5]) << 5));
+ break;
+ case 2:
+ /* [45:34] i.e. 0x5D8 for above example address */
+ hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6));
+ break;
+ case 3:
+ /* [43:32] i.e. 0x634 for above example address */
+ hash_value = ((mc_addr[4]) | (((uint16_t) mc_addr[5]) << 8));
+ break;
}
- return E1000_SUCCESS;
-}
+ hash_value &= 0xFFF;
+
+ return hash_value;
+}
/******************************************************************************
- * Sets up eeprom variables in the hw struct. Must be called after mac_type
- * is configured.
+ * Sets the bit in the multicast table corresponding to the hash value.
*
* hw - Struct containing variables accessed by shared code
+ * hash_value - Multicast address hash value
*****************************************************************************/
void
-e1000_init_eeprom_params(struct e1000_hw *hw)
+e1000_mta_set(struct e1000_hw *hw,
+ uint32_t hash_value)
{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- uint32_t eecd = E1000_READ_REG(hw, EECD);
- uint16_t eeprom_size;
+ uint32_t hash_bit, hash_reg;
+ uint32_t mta;
+ uint32_t temp;
- DEBUGFUNC("e1000_init_eeprom_params");
+ /* The MTA is a register array of 128 32-bit registers.
+ * It is treated like an array of 4096 bits. We want to set
+ * bit BitArray[hash_value]. So we figure out what register
+ * the bit is in, read it, OR in the new bit, then write
+ * back the new value. The register is determined by the
+ * upper 7 bits of the hash value and the bit within that
+ * register are determined by the lower 5 bits of the value.
+ */
+ hash_reg = (hash_value >> 5) & 0x7F;
+ hash_bit = hash_value & 0x1F;
- switch (hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- case e1000_82543:
- case e1000_82544:
- eeprom->type = e1000_eeprom_microwire;
- eeprom->word_size = 64;
- eeprom->opcode_bits = 3;
- eeprom->address_bits = 6;
- eeprom->delay_usec = 50;
- break;
- case e1000_82540:
- case e1000_82545:
- case e1000_82545_rev_3:
- case e1000_82546:
- case e1000_82546_rev_3:
- eeprom->type = e1000_eeprom_microwire;
- eeprom->opcode_bits = 3;
- eeprom->delay_usec = 50;
- if(eecd & E1000_EECD_SIZE) {
- eeprom->word_size = 256;
- eeprom->address_bits = 8;
- } else {
- eeprom->word_size = 64;
- eeprom->address_bits = 6;
- }
- break;
- case e1000_82541:
- case e1000_82541_rev_2:
- case e1000_82547:
- case e1000_82547_rev_2:
- if (eecd & E1000_EECD_TYPE) {
- eeprom->type = e1000_eeprom_spi;
- eeprom->opcode_bits = 8;
- eeprom->delay_usec = 1;
- if (eecd & E1000_EECD_ADDR_BITS) {
- eeprom->page_size = 32;
- eeprom->address_bits = 16;
- } else {
- eeprom->page_size = 8;
- eeprom->address_bits = 8;
- }
- } else {
- eeprom->type = e1000_eeprom_microwire;
- eeprom->opcode_bits = 3;
- eeprom->delay_usec = 50;
- if (eecd & E1000_EECD_ADDR_BITS) {
- eeprom->word_size = 256;
- eeprom->address_bits = 8;
- } else {
- eeprom->word_size = 64;
- eeprom->address_bits = 6;
- }
- }
- break;
- default:
- eeprom->type = e1000_eeprom_spi;
- eeprom->opcode_bits = 8;
- eeprom->delay_usec = 1;
- if (eecd & E1000_EECD_ADDR_BITS) {
- eeprom->page_size = 32;
- eeprom->address_bits = 16;
- } else {
- eeprom->page_size = 8;
- eeprom->address_bits = 8;
- }
- break;
- }
+ mta = E1000_READ_REG_ARRAY(hw, MTA, hash_reg);
- if (eeprom->type == e1000_eeprom_spi) {
- eeprom->word_size = 64;
- if (e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size) == 0) {
- eeprom_size &= EEPROM_SIZE_MASK;
+ mta |= (1 << hash_bit);
- switch (eeprom_size) {
- case EEPROM_SIZE_16KB:
- eeprom->word_size = 8192;
- break;
- case EEPROM_SIZE_8KB:
- eeprom->word_size = 4096;
- break;
- case EEPROM_SIZE_4KB:
- eeprom->word_size = 2048;
- break;
- case EEPROM_SIZE_2KB:
- eeprom->word_size = 1024;
- break;
- case EEPROM_SIZE_1KB:
- eeprom->word_size = 512;
- break;
- case EEPROM_SIZE_512B:
- eeprom->word_size = 256;
- break;
- case EEPROM_SIZE_128B:
- default:
- eeprom->word_size = 64;
- break;
- }
- }
+ /* If we are on an 82544 and we are trying to write an odd offset
+ * in the MTA, save off the previous entry before writing and
+ * restore the old value after writing.
+ */
+ if((hw->mac_type == e1000_82544) && ((hash_reg & 0x1) == 1)) {
+ temp = E1000_READ_REG_ARRAY(hw, MTA, (hash_reg - 1));
+ E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta);
+ E1000_WRITE_REG_ARRAY(hw, MTA, (hash_reg - 1), temp);
+ } else {
+ E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta);
}
}
/******************************************************************************
- * Raises the EEPROM's clock input.
+ * Puts an ethernet address into a receive address register.
*
* hw - Struct containing variables accessed by shared code
- * eecd - EECD's current value
+ * addr - Address to put into receive address register
+ * index - Receive address register to write
*****************************************************************************/
-static void
-e1000_raise_ee_clk(struct e1000_hw *hw,
- uint32_t *eecd)
+void
+e1000_rar_set(struct e1000_hw *hw,
+ uint8_t *addr,
+ uint32_t index)
{
- /* Raise the clock input to the EEPROM (by setting the SK bit), and then
- * wait <delay> microseconds.
+ uint32_t rar_low, rar_high;
+
+ /* HW expects these in little endian so we reverse the byte order
+ * from network order (big endian) to little endian
*/
- *eecd = *eecd | E1000_EECD_SK;
- E1000_WRITE_REG(hw, EECD, *eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(hw->eeprom.delay_usec);
+ rar_low = ((uint32_t) addr[0] |
+ ((uint32_t) addr[1] << 8) |
+ ((uint32_t) addr[2] << 16) | ((uint32_t) addr[3] << 24));
+ rar_high = ((uint32_t) addr[4] | ((uint32_t) addr[5] << 8));
+
+ /* Disable Rx and flush all Rx frames before enabling RSS to avoid Rx
+ * unit hang.
+ *
+ * Description:
+ * If there are any Rx frames queued up or otherwise present in the HW
+ * before RSS is enabled, and then we enable RSS, the HW Rx unit will
+ * hang. To work around this issue, we have to disable receives and
+ * flush out all Rx frames before we enable RSS. To do so, we modify we
+ * redirect all Rx traffic to manageability and then reset the HW.
+ * This flushes away Rx frames, and (since the redirections to
+ * manageability persists across resets) keeps new ones from coming in
+ * while we work. Then, we clear the Address Valid AV bit for all MAC
+ * addresses and undo the re-direction to manageability.
+ * Now, frames are coming in again, but the MAC won't accept them, so
+ * far so good. We now proceed to initialize RSS (if necessary) and
+ * configure the Rx unit. Last, we re-enable the AV bits and continue
+ * on our merry way.
+ */
+ switch (hw->mac_type) {
+ case e1000_82571:
+ case e1000_82572:
+ case e1000_80003es2lan:
+ if (hw->leave_av_bit_off == TRUE)
+ break;
+ default:
+ /* Indicate to hardware the Address is Valid. */
+ rar_high |= E1000_RAH_AV;
+ break;
+ }
+
+ E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low);
+ E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high);
}
/******************************************************************************
- * Lowers the EEPROM's clock input.
+ * Writes a value to the specified offset in the VLAN filter table.
*
* hw - Struct containing variables accessed by shared code
- * eecd - EECD's current value
+ * offset - Offset in VLAN filer table to write
+ * value - Value to write into VLAN filter table
*****************************************************************************/
-static void
-e1000_lower_ee_clk(struct e1000_hw *hw,
- uint32_t *eecd)
+void
+e1000_write_vfta(struct e1000_hw *hw,
+ uint32_t offset,
+ uint32_t value)
{
- /* Lower the clock input to the EEPROM (by clearing the SK bit), and then
- * wait 50 microseconds.
- */
- *eecd = *eecd & ~E1000_EECD_SK;
- E1000_WRITE_REG(hw, EECD, *eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(hw->eeprom.delay_usec);
+ uint32_t temp;
+
+ if((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) {
+ temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1));
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
+ E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp);
+ } else {
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
+ }
}
/******************************************************************************
- * Shift data bits out to the EEPROM.
+ * Clears the VLAN filer table
*
* hw - Struct containing variables accessed by shared code
- * data - data to send to the EEPROM
- * count - number of bits to shift out
*****************************************************************************/
static void
-e1000_shift_out_ee_bits(struct e1000_hw *hw,
- uint16_t data,
- uint16_t count)
+e1000_clear_vfta(struct e1000_hw *hw)
{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- uint32_t eecd;
- uint32_t mask;
-
- /* We need to shift "count" bits out to the EEPROM. So, value in the
- * "data" parameter will be shifted out to the EEPROM one bit at a time.
- * In order to do this, "data" must be broken down into bits.
- */
- mask = 0x01 << (count - 1);
- eecd = E1000_READ_REG(hw, EECD);
- if (eeprom->type == e1000_eeprom_microwire) {
- eecd &= ~E1000_EECD_DO;
- } else if (eeprom->type == e1000_eeprom_spi) {
- eecd |= E1000_EECD_DO;
+ uint32_t offset;
+ uint32_t vfta_value = 0;
+ uint32_t vfta_offset = 0;
+ uint32_t vfta_bit_in_reg = 0;
+
+ if (hw->mac_type == e1000_82573) {
+ if (hw->mng_cookie.vlan_id != 0) {
+ /* The VFTA is a 4096b bit-field, each identifying a single VLAN
+ * ID. The following operations determine which 32b entry
+ * (i.e. offset) into the array we want to set the VLAN ID
+ * (i.e. bit) of the manageability unit. */
+ vfta_offset = (hw->mng_cookie.vlan_id >>
+ E1000_VFTA_ENTRY_SHIFT) &
+ E1000_VFTA_ENTRY_MASK;
+ vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id &
+ E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
+ }
}
- do {
- /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1",
- * and then raising and then lowering the clock (the SK bit controls
- * the clock input to the EEPROM). A "0" is shifted out to the EEPROM
- * by setting "DI" to "0" and then raising and then lowering the clock.
- */
- eecd &= ~E1000_EECD_DI;
-
- if(data & mask)
- eecd |= E1000_EECD_DI;
-
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
+ for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+ /* If the offset we want to clear is the same offset of the
+ * manageability VLAN ID, then clear all bits except that of the
+ * manageability unit */
+ vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value);
+ }
+}
- udelay(eeprom->delay_usec);
+static int32_t
+e1000_id_led_init(struct e1000_hw * hw)
+{
+ uint32_t ledctl;
+ const uint32_t ledctl_mask = 0x000000FF;
+ const uint32_t ledctl_on = E1000_LEDCTL_MODE_LED_ON;
+ const uint32_t ledctl_off = E1000_LEDCTL_MODE_LED_OFF;
+ uint16_t eeprom_data, i, temp;
+ const uint16_t led_mask = 0x0F;
- e1000_raise_ee_clk(hw, &eecd);
- e1000_lower_ee_clk(hw, &eecd);
+ DEBUGFUNC("e1000_id_led_init");
- mask = mask >> 1;
+ if(hw->mac_type < e1000_82540) {
+ /* Nothing to do */
+ return E1000_SUCCESS;
+ }
- } while(mask);
+ ledctl = E1000_READ_REG(hw, LEDCTL);
+ hw->ledctl_default = ledctl;
+ hw->ledctl_mode1 = hw->ledctl_default;
+ hw->ledctl_mode2 = hw->ledctl_default;
- /* We leave the "DI" bit set to "0" when we leave this routine. */
- eecd &= ~E1000_EECD_DI;
- E1000_WRITE_REG(hw, EECD, eecd);
+ if(e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ if((eeprom_data== ID_LED_RESERVED_0000) ||
+ (eeprom_data == ID_LED_RESERVED_FFFF)) eeprom_data = ID_LED_DEFAULT;
+ for(i = 0; i < 4; i++) {
+ temp = (eeprom_data >> (i << 2)) & led_mask;
+ switch(temp) {
+ case ID_LED_ON1_DEF2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_ON1_OFF2:
+ hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode1 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_OFF1_DEF2:
+ case ID_LED_OFF1_ON2:
+ case ID_LED_OFF1_OFF2:
+ hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode1 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ switch(temp) {
+ case ID_LED_DEF1_ON2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_OFF1_ON2:
+ hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode2 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_DEF1_OFF2:
+ case ID_LED_ON1_OFF2:
+ case ID_LED_OFF1_OFF2:
+ hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode2 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ }
+ return E1000_SUCCESS;
}
/******************************************************************************
- * Shift data bits in from the EEPROM
+ * Prepares SW controlable LED for use and saves the current state of the LED.
*
* hw - Struct containing variables accessed by shared code
*****************************************************************************/
-static uint16_t
-e1000_shift_in_ee_bits(struct e1000_hw *hw,
- uint16_t count)
+int32_t
+e1000_setup_led(struct e1000_hw *hw)
{
- uint32_t eecd;
- uint32_t i;
- uint16_t data;
-
- /* In order to read a register from the EEPROM, we need to shift 'count'
- * bits in from the EEPROM. Bits are "shifted in" by raising the clock
- * input to the EEPROM (setting the SK bit), and then reading the value of
- * the "DO" bit. During this "shifting in" process the "DI" bit should
- * always be clear.
- */
+ uint32_t ledctl;
+ int32_t ret_val = E1000_SUCCESS;
- eecd = E1000_READ_REG(hw, EECD);
+ DEBUGFUNC("e1000_setup_led");
- eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
- data = 0;
+ switch(hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ /* No setup necessary */
+ break;
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ /* Turn off PHY Smart Power Down (if enabled) */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ &hw->phy_spd_default);
+ if(ret_val)
+ return ret_val;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ (uint16_t)(hw->phy_spd_default &
+ ~IGP01E1000_GMII_SPD));
+ if(ret_val)
+ return ret_val;
+ /* Fall Through */
+ default:
+ if(hw->media_type == e1000_media_type_fiber) {
+ ledctl = E1000_READ_REG(hw, LEDCTL);
+ /* Save current LEDCTL settings */
+ hw->ledctl_default = ledctl;
+ /* Turn off LED0 */
+ ledctl &= ~(E1000_LEDCTL_LED0_IVRT |
+ E1000_LEDCTL_LED0_BLINK |
+ E1000_LEDCTL_LED0_MODE_MASK);
+ ledctl |= (E1000_LEDCTL_MODE_LED_OFF <<
+ E1000_LEDCTL_LED0_MODE_SHIFT);
+ E1000_WRITE_REG(hw, LEDCTL, ledctl);
+ } else if(hw->media_type == e1000_media_type_copper)
+ E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1);
+ break;
+ }
- for(i = 0; i < count; i++) {
- data = data << 1;
- e1000_raise_ee_clk(hw, &eecd);
+ return E1000_SUCCESS;
+}
- eecd = E1000_READ_REG(hw, EECD);
+/******************************************************************************
+ * Restores the saved state of the SW controlable LED.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+int32_t
+e1000_cleanup_led(struct e1000_hw *hw)
+{
+ int32_t ret_val = E1000_SUCCESS;
- eecd &= ~(E1000_EECD_DI);
- if(eecd & E1000_EECD_DO)
- data |= 1;
+ DEBUGFUNC("e1000_cleanup_led");
- e1000_lower_ee_clk(hw, &eecd);
+ switch(hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ /* No cleanup necessary */
+ break;
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ /* Turn on PHY Smart Power Down (if previously enabled) */
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ hw->phy_spd_default);
+ if(ret_val)
+ return ret_val;
+ /* Fall Through */
+ default:
+ /* Restore LEDCTL settings */
+ E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_default);
+ break;
}
- return data;
+ return E1000_SUCCESS;
}
/******************************************************************************
- * Prepares EEPROM for access
+ * Turns on the software controllable LED
*
* hw - Struct containing variables accessed by shared code
- *
- * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This
- * function should be called before issuing a command to the EEPROM.
*****************************************************************************/
-static int32_t
-e1000_acquire_eeprom(struct e1000_hw *hw)
+int32_t
+e1000_led_on(struct e1000_hw *hw)
{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- uint32_t eecd, i=0;
-
- DEBUGFUNC("e1000_acquire_eeprom");
+ uint32_t ctrl = E1000_READ_REG(hw, CTRL);
- eecd = E1000_READ_REG(hw, EECD);
+ DEBUGFUNC("e1000_led_on");
- /* Request EEPROM Access */
- if(hw->mac_type > e1000_82544) {
- eecd |= E1000_EECD_REQ;
- E1000_WRITE_REG(hw, EECD, eecd);
- eecd = E1000_READ_REG(hw, EECD);
- while((!(eecd & E1000_EECD_GNT)) &&
- (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
- i++;
- udelay(5);
- eecd = E1000_READ_REG(hw, EECD);
+ switch(hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ /* Set SW Defineable Pin 0 to turn on the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ break;
+ case e1000_82544:
+ if(hw->media_type == e1000_media_type_fiber) {
+ /* Set SW Defineable Pin 0 to turn on the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else {
+ /* Clear SW Defineable Pin 0 to turn on the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
}
- if(!(eecd & E1000_EECD_GNT)) {
- eecd &= ~E1000_EECD_REQ;
- E1000_WRITE_REG(hw, EECD, eecd);
- DEBUGOUT("Could not acquire EEPROM grant\n");
- return -E1000_ERR_EEPROM;
+ break;
+ default:
+ if(hw->media_type == e1000_media_type_fiber) {
+ /* Clear SW Defineable Pin 0 to turn on the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else if(hw->media_type == e1000_media_type_copper) {
+ E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode2);
+ return E1000_SUCCESS;
}
+ break;
}
- /* Setup EEPROM for Read/Write */
-
- if (eeprom->type == e1000_eeprom_microwire) {
- /* Clear SK and DI */
- eecd &= ~(E1000_EECD_DI | E1000_EECD_SK);
- E1000_WRITE_REG(hw, EECD, eecd);
-
- /* Set CS */
- eecd |= E1000_EECD_CS;
- E1000_WRITE_REG(hw, EECD, eecd);
- } else if (eeprom->type == e1000_eeprom_spi) {
- /* Clear SK and CS */
- eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
- E1000_WRITE_REG(hw, EECD, eecd);
- udelay(1);
- }
+ E1000_WRITE_REG(hw, CTRL, ctrl);
return E1000_SUCCESS;
}
/******************************************************************************
- * Returns EEPROM to a "standby" state
+ * Turns off the software controllable LED
*
* hw - Struct containing variables accessed by shared code
*****************************************************************************/
-static void
-e1000_standby_eeprom(struct e1000_hw *hw)
+int32_t
+e1000_led_off(struct e1000_hw *hw)
{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- uint32_t eecd;
-
- eecd = E1000_READ_REG(hw, EECD);
+ uint32_t ctrl = E1000_READ_REG(hw, CTRL);
- if(eeprom->type == e1000_eeprom_microwire) {
- eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(eeprom->delay_usec);
+ DEBUGFUNC("e1000_led_off");
- /* Clock high */
- eecd |= E1000_EECD_SK;
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(eeprom->delay_usec);
+ switch(hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ /* Clear SW Defineable Pin 0 to turn off the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ break;
+ case e1000_82544:
+ if(hw->media_type == e1000_media_type_fiber) {
+ /* Clear SW Defineable Pin 0 to turn off the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else {
+ /* Set SW Defineable Pin 0 to turn off the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ }
+ break;
+ default:
+ if(hw->media_type == e1000_media_type_fiber) {
+ /* Set SW Defineable Pin 0 to turn off the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else if(hw->media_type == e1000_media_type_copper) {
+ E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1);
+ return E1000_SUCCESS;
+ }
+ break;
+ }
- /* Select EEPROM */
- eecd |= E1000_EECD_CS;
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(eeprom->delay_usec);
+ E1000_WRITE_REG(hw, CTRL, ctrl);
- /* Clock low */
- eecd &= ~E1000_EECD_SK;
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(eeprom->delay_usec);
- } else if(eeprom->type == e1000_eeprom_spi) {
- /* Toggle CS to flush commands */
- eecd |= E1000_EECD_CS;
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(eeprom->delay_usec);
- eecd &= ~E1000_EECD_CS;
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(eeprom->delay_usec);
- }
+ return E1000_SUCCESS;
}
/******************************************************************************
- * Terminates a command by inverting the EEPROM's chip select pin
+ * Clears all hardware statistics counters.
*
* hw - Struct containing variables accessed by shared code
*****************************************************************************/
static void
-e1000_release_eeprom(struct e1000_hw *hw)
+e1000_clear_hw_cntrs(struct e1000_hw *hw)
{
- uint32_t eecd;
-
- DEBUGFUNC("e1000_release_eeprom");
-
- eecd = E1000_READ_REG(hw, EECD);
-
- if (hw->eeprom.type == e1000_eeprom_spi) {
- eecd |= E1000_EECD_CS; /* Pull CS high */
- eecd &= ~E1000_EECD_SK; /* Lower SCK */
+ volatile uint32_t temp;
- E1000_WRITE_REG(hw, EECD, eecd);
+ temp = E1000_READ_REG(hw, CRCERRS);
+ temp = E1000_READ_REG(hw, SYMERRS);
+ temp = E1000_READ_REG(hw, MPC);
+ temp = E1000_READ_REG(hw, SCC);
+ temp = E1000_READ_REG(hw, ECOL);
+ temp = E1000_READ_REG(hw, MCC);
+ temp = E1000_READ_REG(hw, LATECOL);
+ temp = E1000_READ_REG(hw, COLC);
+ temp = E1000_READ_REG(hw, DC);
+ temp = E1000_READ_REG(hw, SEC);
+ temp = E1000_READ_REG(hw, RLEC);
+ temp = E1000_READ_REG(hw, XONRXC);
+ temp = E1000_READ_REG(hw, XONTXC);
+ temp = E1000_READ_REG(hw, XOFFRXC);
+ temp = E1000_READ_REG(hw, XOFFTXC);
+ temp = E1000_READ_REG(hw, FCRUC);
+ temp = E1000_READ_REG(hw, PRC64);
+ temp = E1000_READ_REG(hw, PRC127);
+ temp = E1000_READ_REG(hw, PRC255);
+ temp = E1000_READ_REG(hw, PRC511);
+ temp = E1000_READ_REG(hw, PRC1023);
+ temp = E1000_READ_REG(hw, PRC1522);
+ temp = E1000_READ_REG(hw, GPRC);
+ temp = E1000_READ_REG(hw, BPRC);
+ temp = E1000_READ_REG(hw, MPRC);
+ temp = E1000_READ_REG(hw, GPTC);
+ temp = E1000_READ_REG(hw, GORCL);
+ temp = E1000_READ_REG(hw, GORCH);
+ temp = E1000_READ_REG(hw, GOTCL);
+ temp = E1000_READ_REG(hw, GOTCH);
+ temp = E1000_READ_REG(hw, RNBC);
+ temp = E1000_READ_REG(hw, RUC);
+ temp = E1000_READ_REG(hw, RFC);
+ temp = E1000_READ_REG(hw, ROC);
+ temp = E1000_READ_REG(hw, RJC);
+ temp = E1000_READ_REG(hw, TORL);
+ temp = E1000_READ_REG(hw, TORH);
+ temp = E1000_READ_REG(hw, TOTL);
+ temp = E1000_READ_REG(hw, TOTH);
+ temp = E1000_READ_REG(hw, TPR);
+ temp = E1000_READ_REG(hw, TPT);
+ temp = E1000_READ_REG(hw, PTC64);
+ temp = E1000_READ_REG(hw, PTC127);
+ temp = E1000_READ_REG(hw, PTC255);
+ temp = E1000_READ_REG(hw, PTC511);
+ temp = E1000_READ_REG(hw, PTC1023);
+ temp = E1000_READ_REG(hw, PTC1522);
+ temp = E1000_READ_REG(hw, MPTC);
+ temp = E1000_READ_REG(hw, BPTC);
- udelay(hw->eeprom.delay_usec);
- } else if(hw->eeprom.type == e1000_eeprom_microwire) {
- /* cleanup eeprom */
+ if(hw->mac_type < e1000_82543) return;
- /* CS on Microwire is active-high */
- eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);
+ temp = E1000_READ_REG(hw, ALGNERRC);
+ temp = E1000_READ_REG(hw, RXERRC);
+ temp = E1000_READ_REG(hw, TNCRS);
+ temp = E1000_READ_REG(hw, CEXTERR);
+ temp = E1000_READ_REG(hw, TSCTC);
+ temp = E1000_READ_REG(hw, TSCTFC);
- E1000_WRITE_REG(hw, EECD, eecd);
+ if(hw->mac_type <= e1000_82544) return;
- /* Rising edge of clock */
- eecd |= E1000_EECD_SK;
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(hw->eeprom.delay_usec);
+ temp = E1000_READ_REG(hw, MGTPRC);
+ temp = E1000_READ_REG(hw, MGTPDC);
+ temp = E1000_READ_REG(hw, MGTPTC);
- /* Falling edge of clock */
- eecd &= ~E1000_EECD_SK;
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(hw->eeprom.delay_usec);
- }
+ if(hw->mac_type <= e1000_82547_rev_2) return;
+
+ temp = E1000_READ_REG(hw, IAC);
+ temp = E1000_READ_REG(hw, ICRXOC);
+ temp = E1000_READ_REG(hw, ICRXPTC);
+ temp = E1000_READ_REG(hw, ICRXATC);
+ temp = E1000_READ_REG(hw, ICTXPTC);
+ temp = E1000_READ_REG(hw, ICTXATC);
+ temp = E1000_READ_REG(hw, ICTXQEC);
+ temp = E1000_READ_REG(hw, ICTXQMTC);
+ temp = E1000_READ_REG(hw, ICRXDMTC);
+}
- /* Stop requesting EEPROM access */
- if(hw->mac_type > e1000_82544) {
- eecd &= ~E1000_EECD_REQ;
- E1000_WRITE_REG(hw, EECD, eecd);
+/******************************************************************************
+ * Resets Adaptive IFS to its default state.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Call this after e1000_init_hw. You may override the IFS defaults by setting
+ * hw->ifs_params_forced to TRUE. However, you must initialize hw->
+ * current_ifs_val, ifs_min_val, ifs_max_val, ifs_step_size, and ifs_ratio
+ * before calling this function.
+ *****************************************************************************/
+void
+e1000_reset_adaptive(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_reset_adaptive");
+
+ if(hw->adaptive_ifs) {
+ if(!hw->ifs_params_forced) {
+ hw->current_ifs_val = 0;
+ hw->ifs_min_val = IFS_MIN;
+ hw->ifs_max_val = IFS_MAX;
+ hw->ifs_step_size = IFS_STEP;
+ hw->ifs_ratio = IFS_RATIO;
+ }
+ hw->in_ifs_mode = FALSE;
+ E1000_WRITE_REG(hw, AIT, 0);
+ } else {
+ DEBUGOUT("Not in Adaptive IFS mode!\n");
}
}
/******************************************************************************
- * Reads a 16 bit word from the EEPROM.
+ * Called during the callback/watchdog routine to update IFS value based on
+ * the ratio of transmits to collisions.
*
* hw - Struct containing variables accessed by shared code
+ * tx_packets - Number of transmits since last callback
+ * total_collisions - Number of collisions since last callback
*****************************************************************************/
-int32_t
-e1000_spi_eeprom_ready(struct e1000_hw *hw)
+void
+e1000_update_adaptive(struct e1000_hw *hw)
{
- uint16_t retry_count = 0;
- uint8_t spi_stat_reg;
-
- DEBUGFUNC("e1000_spi_eeprom_ready");
-
- /* Read "Status Register" repeatedly until the LSB is cleared. The
- * EEPROM will signal that the command has been completed by clearing
- * bit 0 of the internal status register. If it's not cleared within
- * 5 milliseconds, then error out.
- */
- retry_count = 0;
- do {
- e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI,
- hw->eeprom.opcode_bits);
- spi_stat_reg = (uint8_t)e1000_shift_in_ee_bits(hw, 8);
- if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI))
- break;
-
- udelay(5);
- retry_count += 5;
-
- e1000_standby_eeprom(hw);
- } while(retry_count < EEPROM_MAX_RETRY_SPI);
+ DEBUGFUNC("e1000_update_adaptive");
- /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and
- * only 0-5mSec on 5V devices)
- */
- if(retry_count >= EEPROM_MAX_RETRY_SPI) {
- DEBUGOUT("SPI EEPROM Status error\n");
- return -E1000_ERR_EEPROM;
+ if(hw->adaptive_ifs) {
+ if((hw->collision_delta * hw->ifs_ratio) > hw->tx_packet_delta) {
+ if(hw->tx_packet_delta > MIN_NUM_XMITS) {
+ hw->in_ifs_mode = TRUE;
+ if(hw->current_ifs_val < hw->ifs_max_val) {
+ if(hw->current_ifs_val == 0)
+ hw->current_ifs_val = hw->ifs_min_val;
+ else
+ hw->current_ifs_val += hw->ifs_step_size;
+ E1000_WRITE_REG(hw, AIT, hw->current_ifs_val);
+ }
+ }
+ } else {
+ if(hw->in_ifs_mode && (hw->tx_packet_delta <= MIN_NUM_XMITS)) {
+ hw->current_ifs_val = 0;
+ hw->in_ifs_mode = FALSE;
+ E1000_WRITE_REG(hw, AIT, 0);
+ }
+ }
+ } else {
+ DEBUGOUT("Not in Adaptive IFS mode!\n");
}
-
- return E1000_SUCCESS;
}
/******************************************************************************
- * Reads a 16 bit word from the EEPROM.
+ * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT
*
* hw - Struct containing variables accessed by shared code
- * offset - offset of word in the EEPROM to read
- * data - word read from the EEPROM
- * words - number of words to read
+ * frame_len - The length of the frame in question
+ * mac_addr - The Ethernet destination address of the frame in question
*****************************************************************************/
-int32_t
-e1000_read_eeprom(struct e1000_hw *hw,
- uint16_t offset,
- uint16_t words,
- uint16_t *data)
+void
+e1000_tbi_adjust_stats(struct e1000_hw *hw,
+ struct e1000_hw_stats *stats,
+ uint32_t frame_len,
+ uint8_t *mac_addr)
{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- uint32_t i = 0;
-
- DEBUGFUNC("e1000_read_eeprom");
+ uint64_t carry_bit;
- /* A check for invalid values: offset too large, too many words, and not
- * enough words.
+ /* First adjust the frame length. */
+ frame_len--;
+ /* We need to adjust the statistics counters, since the hardware
+ * counters overcount this packet as a CRC error and undercount
+ * the packet as a good packet
*/
- if((offset > eeprom->word_size) || (words > eeprom->word_size - offset) ||
- (words == 0)) {
- DEBUGOUT("\"words\" parameter out of bounds\n");
- return -E1000_ERR_EEPROM;
- }
-
- /* Prepare the EEPROM for reading */
- if(e1000_acquire_eeprom(hw) != E1000_SUCCESS)
- return -E1000_ERR_EEPROM;
-
- if(eeprom->type == e1000_eeprom_spi) {
- uint16_t word_in;
- uint8_t read_opcode = EEPROM_READ_OPCODE_SPI;
-
- if(e1000_spi_eeprom_ready(hw)) {
- e1000_release_eeprom(hw);
- return -E1000_ERR_EEPROM;
- }
-
- e1000_standby_eeprom(hw);
-
- /* Some SPI eeproms use the 8th address bit embedded in the opcode */
- if((eeprom->address_bits == 8) && (offset >= 128))
- read_opcode |= EEPROM_A8_OPCODE_SPI;
-
- /* Send the READ command (opcode + addr) */
- e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits);
- e1000_shift_out_ee_bits(hw, (uint16_t)(offset*2), eeprom->address_bits);
+ /* This packet should not be counted as a CRC error. */
+ stats->crcerrs--;
+ /* This packet does count as a Good Packet Received. */
+ stats->gprc++;
- /* Read the data. The address of the eeprom internally increments with
- * each byte (spi) being read, saving on the overhead of eeprom setup
- * and tear-down. The address counter will roll over if reading beyond
- * the size of the eeprom, thus allowing the entire memory to be read
- * starting from any offset. */
- for (i = 0; i < words; i++) {
- word_in = e1000_shift_in_ee_bits(hw, 16);
- data[i] = (word_in >> 8) | (word_in << 8);
- }
- } else if(eeprom->type == e1000_eeprom_microwire) {
- for (i = 0; i < words; i++) {
- /* Send the READ command (opcode + addr) */
- e1000_shift_out_ee_bits(hw, EEPROM_READ_OPCODE_MICROWIRE,
- eeprom->opcode_bits);
- e1000_shift_out_ee_bits(hw, (uint16_t)(offset + i),
- eeprom->address_bits);
+ /* Adjust the Good Octets received counters */
+ carry_bit = 0x80000000 & stats->gorcl;
+ stats->gorcl += frame_len;
+ /* If the high bit of Gorcl (the low 32 bits of the Good Octets
+ * Received Count) was one before the addition,
+ * AND it is zero after, then we lost the carry out,
+ * need to add one to Gorch (Good Octets Received Count High).
+ * This could be simplified if all environments supported
+ * 64-bit integers.
+ */
+ if(carry_bit && ((stats->gorcl & 0x80000000) == 0))
+ stats->gorch++;
+ /* Is this a broadcast or multicast? Check broadcast first,
+ * since the test for a multicast frame will test positive on
+ * a broadcast frame.
+ */
+ if((mac_addr[0] == (uint8_t) 0xff) && (mac_addr[1] == (uint8_t) 0xff))
+ /* Broadcast packet */
+ stats->bprc++;
+ else if(*mac_addr & 0x01)
+ /* Multicast packet */
+ stats->mprc++;
- /* Read the data. For microwire, each word requires the overhead
- * of eeprom setup and tear-down. */
- data[i] = e1000_shift_in_ee_bits(hw, 16);
- e1000_standby_eeprom(hw);
- }
+ if(frame_len == hw->max_frame_size) {
+ /* In this case, the hardware has overcounted the number of
+ * oversize frames.
+ */
+ if(stats->roc > 0)
+ stats->roc--;
}
- /* End this read operation */
- e1000_release_eeprom(hw);
-
- return E1000_SUCCESS;
+ /* Adjust the bin counters when the extra byte put the frame in the
+ * wrong bin. Remember that the frame_len was adjusted above.
+ */
+ if(frame_len == 64) {
+ stats->prc64++;
+ stats->prc127--;
+ } else if(frame_len == 127) {
+ stats->prc127++;
+ stats->prc255--;
+ } else if(frame_len == 255) {
+ stats->prc255++;
+ stats->prc511--;
+ } else if(frame_len == 511) {
+ stats->prc511++;
+ stats->prc1023--;
+ } else if(frame_len == 1023) {
+ stats->prc1023++;
+ stats->prc1522--;
+ } else if(frame_len == 1522) {
+ stats->prc1522++;
+ }
}
/******************************************************************************
- * Verifies that the EEPROM has a valid checksum
+ * Gets the current PCI bus type, speed, and width of the hardware
*
* hw - Struct containing variables accessed by shared code
- *
- * Reads the first 64 16 bit words of the EEPROM and sums the values read.
- * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is
- * valid.
*****************************************************************************/
-int32_t
-e1000_validate_eeprom_checksum(struct e1000_hw *hw)
+void
+e1000_get_bus_info(struct e1000_hw *hw)
{
- uint16_t checksum = 0;
- uint16_t i, eeprom_data;
-
- DEBUGFUNC("e1000_validate_eeprom_checksum");
+ uint32_t status;
- for(i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
- if(e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ hw->bus_type = e1000_bus_type_unknown;
+ hw->bus_speed = e1000_bus_speed_unknown;
+ hw->bus_width = e1000_bus_width_unknown;
+ break;
+ case e1000_82572:
+ case e1000_82573:
+ hw->bus_type = e1000_bus_type_pci_express;
+ hw->bus_speed = e1000_bus_speed_2500;
+ hw->bus_width = e1000_bus_width_pciex_1;
+ break;
+ case e1000_82571:
+ case e1000_80003es2lan:
+ hw->bus_type = e1000_bus_type_pci_express;
+ hw->bus_speed = e1000_bus_speed_2500;
+ hw->bus_width = e1000_bus_width_pciex_4;
+ break;
+ default:
+ status = E1000_READ_REG(hw, STATUS);
+ hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ?
+ e1000_bus_type_pcix : e1000_bus_type_pci;
+
+ if(hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) {
+ hw->bus_speed = (hw->bus_type == e1000_bus_type_pci) ?
+ e1000_bus_speed_66 : e1000_bus_speed_120;
+ } else if(hw->bus_type == e1000_bus_type_pci) {
+ hw->bus_speed = (status & E1000_STATUS_PCI66) ?
+ e1000_bus_speed_66 : e1000_bus_speed_33;
+ } else {
+ switch (status & E1000_STATUS_PCIX_SPEED) {
+ case E1000_STATUS_PCIX_SPEED_66:
+ hw->bus_speed = e1000_bus_speed_66;
+ break;
+ case E1000_STATUS_PCIX_SPEED_100:
+ hw->bus_speed = e1000_bus_speed_100;
+ break;
+ case E1000_STATUS_PCIX_SPEED_133:
+ hw->bus_speed = e1000_bus_speed_133;
+ break;
+ default:
+ hw->bus_speed = e1000_bus_speed_reserved;
+ break;
+ }
}
- checksum += eeprom_data;
- }
-
- if(checksum == (uint16_t) EEPROM_SUM)
- return E1000_SUCCESS;
- else {
- DEBUGOUT("EEPROM Checksum Invalid\n");
- return -E1000_ERR_EEPROM;
+ hw->bus_width = (status & E1000_STATUS_BUS64) ?
+ e1000_bus_width_64 : e1000_bus_width_32;
+ break;
}
}
+#if 0
/******************************************************************************
- * Calculates the EEPROM checksum and writes it to the EEPROM
+ * Reads a value from one of the devices registers using port I/O (as opposed
+ * memory mapped I/O). Only 82544 and newer devices support port I/O.
*
* hw - Struct containing variables accessed by shared code
- *
- * Sums the first 63 16 bit words of the EEPROM. Subtracts the sum from 0xBABA.
- * Writes the difference to word offset 63 of the EEPROM.
+ * offset - offset to read from
*****************************************************************************/
-int32_t
-e1000_update_eeprom_checksum(struct e1000_hw *hw)
+uint32_t
+e1000_read_reg_io(struct e1000_hw *hw,
+ uint32_t offset)
{
- uint16_t checksum = 0;
- uint16_t i, eeprom_data;
-
- DEBUGFUNC("e1000_update_eeprom_checksum");
+ unsigned long io_addr = hw->io_base;
+ unsigned long io_data = hw->io_base + 4;
- for(i = 0; i < EEPROM_CHECKSUM_REG; i++) {
- if(e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- checksum += eeprom_data;
- }
- checksum = (uint16_t) EEPROM_SUM - checksum;
- if(e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) {
- DEBUGOUT("EEPROM Write Error\n");
- return -E1000_ERR_EEPROM;
- }
- return E1000_SUCCESS;
+ e1000_io_write(hw, io_addr, offset);
+ return e1000_io_read(hw, io_data);
}
+#endif /* 0 */
/******************************************************************************
- * Parent function for writing words to the different EEPROM types.
+ * Writes a value to one of the devices registers using port I/O (as opposed to
+ * memory mapped I/O). Only 82544 and newer devices support port I/O.
*
* hw - Struct containing variables accessed by shared code
- * offset - offset within the EEPROM to be written to
- * words - number of words to write
- * data - 16 bit word to be written to the EEPROM
- *
- * If e1000_update_eeprom_checksum is not called after this function, the
- * EEPROM will most likely contain an invalid checksum.
+ * offset - offset to write to
+ * value - value to write
*****************************************************************************/
-int32_t
-e1000_write_eeprom(struct e1000_hw *hw,
- uint16_t offset,
- uint16_t words,
- uint16_t *data)
+static void
+e1000_write_reg_io(struct e1000_hw *hw,
+ uint32_t offset,
+ uint32_t value)
{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- int32_t status = 0;
-
- DEBUGFUNC("e1000_write_eeprom");
-
- /* A check for invalid values: offset too large, too many words, and not
- * enough words.
- */
- if((offset > eeprom->word_size) || (words > eeprom->word_size - offset) ||
- (words == 0)) {
- DEBUGOUT("\"words\" parameter out of bounds\n");
- return -E1000_ERR_EEPROM;
- }
-
- /* Prepare the EEPROM for writing */
- if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
- return -E1000_ERR_EEPROM;
-
- if(eeprom->type == e1000_eeprom_microwire) {
- status = e1000_write_eeprom_microwire(hw, offset, words, data);
- } else {
- status = e1000_write_eeprom_spi(hw, offset, words, data);
- msec_delay(10);
- }
-
- /* Done with writing */
- e1000_release_eeprom(hw);
+ unsigned long io_addr = hw->io_base;
+ unsigned long io_data = hw->io_base + 4;
- return status;
+ e1000_io_write(hw, io_addr, offset);
+ e1000_io_write(hw, io_data, value);
}
+
/******************************************************************************
- * Writes a 16 bit word to a given offset in an SPI EEPROM.
+ * Estimates the cable length.
*
* hw - Struct containing variables accessed by shared code
- * offset - offset within the EEPROM to be written to
- * words - number of words to write
- * data - pointer to array of 8 bit words to be written to the EEPROM
+ * min_length - The estimated minimum length
+ * max_length - The estimated maximum length
+ *
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
*
+ * This function always returns a ranged length (minimum & maximum).
+ * So for M88 phy's, this function interprets the one value returned from the
+ * register to the minimum and maximum range.
+ * For IGP phy's, the function calculates the range by the AGC registers.
*****************************************************************************/
-int32_t
-e1000_write_eeprom_spi(struct e1000_hw *hw,
- uint16_t offset,
- uint16_t words,
- uint16_t *data)
+static int32_t
+e1000_get_cable_length(struct e1000_hw *hw,
+ uint16_t *min_length,
+ uint16_t *max_length)
{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- uint16_t widx = 0;
-
- DEBUGFUNC("e1000_write_eeprom_spi");
-
- while (widx < words) {
- uint8_t write_opcode = EEPROM_WRITE_OPCODE_SPI;
-
- if(e1000_spi_eeprom_ready(hw)) return -E1000_ERR_EEPROM;
-
- e1000_standby_eeprom(hw);
-
- /* Send the WRITE ENABLE command (8 bit opcode ) */
- e1000_shift_out_ee_bits(hw, EEPROM_WREN_OPCODE_SPI,
- eeprom->opcode_bits);
-
- e1000_standby_eeprom(hw);
+ int32_t ret_val;
+ uint16_t agc_value = 0;
+ uint16_t cur_agc, min_agc = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
+ uint16_t max_agc = 0;
+ uint16_t i, phy_data;
+ uint16_t cable_length;
- /* Some SPI eeproms use the 8th address bit embedded in the opcode */
- if((eeprom->address_bits == 8) && (offset >= 128))
- write_opcode |= EEPROM_A8_OPCODE_SPI;
+ DEBUGFUNC("e1000_get_cable_length");
- /* Send the Write command (8-bit opcode + addr) */
- e1000_shift_out_ee_bits(hw, write_opcode, eeprom->opcode_bits);
+ *min_length = *max_length = 0;
- e1000_shift_out_ee_bits(hw, (uint16_t)((offset + widx)*2),
- eeprom->address_bits);
+ /* Use old method for Phy older than IGP */
+ if(hw->phy_type == e1000_phy_m88) {
- /* Send the data */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
+ cable_length = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT;
- /* Loop to allow for up to whole page write (32 bytes) of eeprom */
- while (widx < words) {
- uint16_t word_out = data[widx];
- word_out = (word_out >> 8) | (word_out << 8);
- e1000_shift_out_ee_bits(hw, word_out, 16);
- widx++;
+ /* Convert the enum value to ranged values */
+ switch (cable_length) {
+ case e1000_cable_length_50:
+ *min_length = 0;
+ *max_length = e1000_igp_cable_length_50;
+ break;
+ case e1000_cable_length_50_80:
+ *min_length = e1000_igp_cable_length_50;
+ *max_length = e1000_igp_cable_length_80;
+ break;
+ case e1000_cable_length_80_110:
+ *min_length = e1000_igp_cable_length_80;
+ *max_length = e1000_igp_cable_length_110;
+ break;
+ case e1000_cable_length_110_140:
+ *min_length = e1000_igp_cable_length_110;
+ *max_length = e1000_igp_cable_length_140;
+ break;
+ case e1000_cable_length_140:
+ *min_length = e1000_igp_cable_length_140;
+ *max_length = e1000_igp_cable_length_170;
+ break;
+ default:
+ return -E1000_ERR_PHY;
+ break;
+ }
+ } else if (hw->phy_type == e1000_phy_gg82563) {
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ cable_length = phy_data & GG82563_DSPD_CABLE_LENGTH;
- /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE
- * operation, while the smaller eeproms are capable of an 8-byte
- * PAGE WRITE operation. Break the inner loop to pass new address
- */
- if((((offset + widx)*2) % eeprom->page_size) == 0) {
- e1000_standby_eeprom(hw);
- break;
- }
+ switch (cable_length) {
+ case e1000_gg_cable_length_60:
+ *min_length = 0;
+ *max_length = e1000_igp_cable_length_60;
+ break;
+ case e1000_gg_cable_length_60_115:
+ *min_length = e1000_igp_cable_length_60;
+ *max_length = e1000_igp_cable_length_115;
+ break;
+ case e1000_gg_cable_length_115_150:
+ *min_length = e1000_igp_cable_length_115;
+ *max_length = e1000_igp_cable_length_150;
+ break;
+ case e1000_gg_cable_length_150:
+ *min_length = e1000_igp_cable_length_150;
+ *max_length = e1000_igp_cable_length_180;
+ break;
+ default:
+ return -E1000_ERR_PHY;
+ break;
}
- }
+ } else if(hw->phy_type == e1000_phy_igp) { /* For IGP PHY */
+ uint16_t agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
+ {IGP01E1000_PHY_AGC_A,
+ IGP01E1000_PHY_AGC_B,
+ IGP01E1000_PHY_AGC_C,
+ IGP01E1000_PHY_AGC_D};
+ /* Read the AGC registers for all channels */
+ for(i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
- return E1000_SUCCESS;
-}
+ ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data);
+ if(ret_val)
+ return ret_val;
-/******************************************************************************
- * Writes a 16 bit word to a given offset in a Microwire EEPROM.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - offset within the EEPROM to be written to
- * words - number of words to write
- * data - pointer to array of 16 bit words to be written to the EEPROM
- *
- *****************************************************************************/
-int32_t
-e1000_write_eeprom_microwire(struct e1000_hw *hw,
- uint16_t offset,
- uint16_t words,
- uint16_t *data)
-{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- uint32_t eecd;
- uint16_t words_written = 0;
- uint16_t i = 0;
+ cur_agc = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT;
- DEBUGFUNC("e1000_write_eeprom_microwire");
+ /* Array bound check. */
+ if((cur_agc >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) ||
+ (cur_agc == 0))
+ return -E1000_ERR_PHY;
- /* Send the write enable command to the EEPROM (3-bit opcode plus
- * 6/8-bit dummy address beginning with 11). It's less work to include
- * the 11 of the dummy address as part of the opcode than it is to shift
- * it over the correct number of bits for the address. This puts the
- * EEPROM into write/erase mode.
- */
- e1000_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE_MICROWIRE,
- (uint16_t)(eeprom->opcode_bits + 2));
+ agc_value += cur_agc;
- e1000_shift_out_ee_bits(hw, 0, (uint16_t)(eeprom->address_bits - 2));
+ /* Update minimal AGC value. */
+ if(min_agc > cur_agc)
+ min_agc = cur_agc;
+ }
- /* Prepare the EEPROM */
- e1000_standby_eeprom(hw);
+ /* Remove the minimal AGC result for length < 50m */
+ if(agc_value < IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) {
+ agc_value -= min_agc;
- while (words_written < words) {
- /* Send the Write command (3-bit opcode + addr) */
- e1000_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE_MICROWIRE,
- eeprom->opcode_bits);
+ /* Get the average length of the remaining 3 channels */
+ agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1);
+ } else {
+ /* Get the average length of all the 4 channels. */
+ agc_value /= IGP01E1000_PHY_CHANNEL_NUM;
+ }
- e1000_shift_out_ee_bits(hw, (uint16_t)(offset + words_written),
- eeprom->address_bits);
+ /* Set the range of the calculated length. */
+ *min_length = ((e1000_igp_cable_length_table[agc_value] -
+ IGP01E1000_AGC_RANGE) > 0) ?
+ (e1000_igp_cable_length_table[agc_value] -
+ IGP01E1000_AGC_RANGE) : 0;
+ *max_length = e1000_igp_cable_length_table[agc_value] +
+ IGP01E1000_AGC_RANGE;
+ } else if (hw->phy_type == e1000_phy_igp_2) {
+ uint16_t agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] =
+ {IGP02E1000_PHY_AGC_A,
+ IGP02E1000_PHY_AGC_B,
+ IGP02E1000_PHY_AGC_C,
+ IGP02E1000_PHY_AGC_D};
+ /* Read the AGC registers for all channels */
+ for (i = 0; i < IGP02E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data);
+ if (ret_val)
+ return ret_val;
- /* Send the data */
- e1000_shift_out_ee_bits(hw, data[words_written], 16);
+ /* Getting bits 15:9, which represent the combination of course and
+ * fine gain values. The result is a number that can be put into
+ * the lookup table to obtain the approximate cable length. */
+ cur_agc = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
+ IGP02E1000_AGC_LENGTH_MASK;
- /* Toggle the CS line. This in effect tells the EEPROM to execute
- * the previous command.
- */
- e1000_standby_eeprom(hw);
+ /* Remove min & max AGC values from calculation. */
+ if (e1000_igp_2_cable_length_table[min_agc] > e1000_igp_2_cable_length_table[cur_agc])
+ min_agc = cur_agc;
+ if (e1000_igp_2_cable_length_table[max_agc] < e1000_igp_2_cable_length_table[cur_agc])
+ max_agc = cur_agc;
- /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will
- * signal that the command has been completed by raising the DO signal.
- * If DO does not go high in 10 milliseconds, then error out.
- */
- for(i = 0; i < 200; i++) {
- eecd = E1000_READ_REG(hw, EECD);
- if(eecd & E1000_EECD_DO) break;
- udelay(50);
- }
- if(i == 200) {
- DEBUGOUT("EEPROM Write did not complete\n");
- return -E1000_ERR_EEPROM;
+ agc_value += e1000_igp_2_cable_length_table[cur_agc];
}
- /* Recover from write */
- e1000_standby_eeprom(hw);
+ agc_value -= (e1000_igp_2_cable_length_table[min_agc] + e1000_igp_2_cable_length_table[max_agc]);
+ agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2);
- words_written++;
+ /* Calculate cable length with the error range of +/- 10 meters. */
+ *min_length = ((agc_value - IGP02E1000_AGC_RANGE) > 0) ?
+ (agc_value - IGP02E1000_AGC_RANGE) : 0;
+ *max_length = agc_value + IGP02E1000_AGC_RANGE;
}
- /* Send the write disable command to the EEPROM (3-bit opcode plus
- * 6/8-bit dummy address beginning with 10). It's less work to include
- * the 10 of the dummy address as part of the opcode than it is to shift
- * it over the correct number of bits for the address. This takes the
- * EEPROM out of write/erase mode.
- */
- e1000_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE_MICROWIRE,
- (uint16_t)(eeprom->opcode_bits + 2));
-
- e1000_shift_out_ee_bits(hw, 0, (uint16_t)(eeprom->address_bits - 2));
-
return E1000_SUCCESS;
}
/******************************************************************************
- * Reads the adapter's part number from the EEPROM
+ * Check the cable polarity
*
* hw - Struct containing variables accessed by shared code
- * part_num - Adapter's part number
+ * polarity - output parameter : 0 - Polarity is not reversed
+ * 1 - Polarity is reversed.
+ *
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
+ *
+ * For phy's older then IGP, this function simply reads the polarity bit in the
+ * Phy Status register. For IGP phy's, this bit is valid only if link speed is
+ * 10 Mbps. If the link speed is 100 Mbps there is no polarity so this bit will
+ * return 0. If the link speed is 1000 Mbps the polarity status is in the
+ * IGP01E1000_PHY_PCS_INIT_REG.
*****************************************************************************/
-int32_t
-e1000_read_part_num(struct e1000_hw *hw,
- uint32_t *part_num)
+static int32_t
+e1000_check_polarity(struct e1000_hw *hw,
+ uint16_t *polarity)
{
- uint16_t offset = EEPROM_PBA_BYTE_1;
- uint16_t eeprom_data;
+ int32_t ret_val;
+ uint16_t phy_data;
- DEBUGFUNC("e1000_read_part_num");
+ DEBUGFUNC("e1000_check_polarity");
- /* Get word 0 from EEPROM */
- if(e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- /* Save word 0 in upper half of part_num */
- *part_num = (uint32_t) (eeprom_data << 16);
+ if ((hw->phy_type == e1000_phy_m88) ||
+ (hw->phy_type == e1000_phy_gg82563)) {
+ /* return the Polarity bit in the Status register. */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
+ *polarity = (phy_data & M88E1000_PSSR_REV_POLARITY) >>
+ M88E1000_PSSR_REV_POLARITY_SHIFT;
+ } else if(hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2) {
+ /* Read the Status register to check the speed */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
- /* Get word 1 from EEPROM */
- if(e1000_read_eeprom(hw, ++offset, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- /* Save word 1 in lower half of part_num */
- *part_num |= eeprom_data;
+ /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to
+ * find the polarity status */
+ if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+ /* Read the GIG initialization PCS register (0x00B4) */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ /* Check the polarity bits */
+ *polarity = (phy_data & IGP01E1000_PHY_POLARITY_MASK) ? 1 : 0;
+ } else {
+ /* For 10 Mbps, read the polarity bit in the status register. (for
+ * 100 Mbps this bit is always 0) */
+ *polarity = phy_data & IGP01E1000_PSSR_POLARITY_REVERSED;
+ }
+ }
return E1000_SUCCESS;
}
/******************************************************************************
- * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
- * second function of dual function devices
+ * Check if Downshift occured
*
* hw - Struct containing variables accessed by shared code
+ * downshift - output parameter : 0 - No Downshift ocured.
+ * 1 - Downshift ocured.
+ *
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
+ *
+ * For phy's older then IGP, this function reads the Downshift bit in the Phy
+ * Specific Status register. For IGP phy's, it reads the Downgrade bit in the
+ * Link Health register. In IGP this bit is latched high, so the driver must
+ * read it immediately after link is established.
*****************************************************************************/
-int32_t
-e1000_read_mac_addr(struct e1000_hw * hw)
+static int32_t
+e1000_check_downshift(struct e1000_hw *hw)
{
- uint16_t offset;
- uint16_t eeprom_data, i;
+ int32_t ret_val;
+ uint16_t phy_data;
- DEBUGFUNC("e1000_read_mac_addr");
+ DEBUGFUNC("e1000_check_downshift");
- for(i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
- offset = i >> 1;
- if(e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- hw->perm_mac_addr[i] = (uint8_t) (eeprom_data & 0x00FF);
- hw->perm_mac_addr[i+1] = (uint8_t) (eeprom_data >> 8);
+ if(hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ hw->speed_downgraded = (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0;
+ } else if ((hw->phy_type == e1000_phy_m88) ||
+ (hw->phy_type == e1000_phy_gg82563)) {
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >>
+ M88E1000_PSSR_DOWNSHIFT_SHIFT;
}
- if(((hw->mac_type == e1000_82546) || (hw->mac_type == e1000_82546_rev_3)) &&
- (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1))
- hw->perm_mac_addr[5] ^= 0x01;
- for(i = 0; i < NODE_ADDRESS_SIZE; i++)
- hw->mac_addr[i] = hw->perm_mac_addr[i];
return E1000_SUCCESS;
}
-/******************************************************************************
- * Initializes receive address filters.
+/*****************************************************************************
*
- * hw - Struct containing variables accessed by shared code
+ * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a
+ * gigabit link is achieved to improve link quality.
*
- * Places the MAC address in receive address register 0 and clears the rest
- * of the receive addresss registers. Clears the multicast table. Assumes
- * the receiver is in reset when the routine is called.
- *****************************************************************************/
-void
-e1000_init_rx_addrs(struct e1000_hw *hw)
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * E1000_SUCCESS at any other case.
+ *
+ ****************************************************************************/
+
+static int32_t
+e1000_config_dsp_after_link_change(struct e1000_hw *hw,
+ boolean_t link_up)
{
- uint32_t i;
+ int32_t ret_val;
+ uint16_t phy_data, phy_saved_data, speed, duplex, i;
+ uint16_t dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
+ {IGP01E1000_PHY_AGC_PARAM_A,
+ IGP01E1000_PHY_AGC_PARAM_B,
+ IGP01E1000_PHY_AGC_PARAM_C,
+ IGP01E1000_PHY_AGC_PARAM_D};
+ uint16_t min_length, max_length;
- DEBUGFUNC("e1000_init_rx_addrs");
+ DEBUGFUNC("e1000_config_dsp_after_link_change");
- /* Setup the receive address. */
- DEBUGOUT("Programming MAC Address into RAR[0]\n");
+ if(hw->phy_type != e1000_phy_igp)
+ return E1000_SUCCESS;
- e1000_rar_set(hw, hw->mac_addr, 0);
+ if(link_up) {
+ ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if(ret_val) {
+ DEBUGOUT("Error getting link speed and duplex\n");
+ return ret_val;
+ }
- /* Zero out the other 15 receive addresses. */
- DEBUGOUT("Clearing RAR[1-15]\n");
- for(i = 1; i < E1000_RAR_ENTRIES; i++) {
- E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
- E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
- }
-}
+ if(speed == SPEED_1000) {
-/******************************************************************************
- * Updates the MAC's list of multicast addresses.
- *
- * hw - Struct containing variables accessed by shared code
- * mc_addr_list - the list of new multicast addresses
- * mc_addr_count - number of addresses
- * pad - number of bytes between addresses in the list
- * rar_used_count - offset where to start adding mc addresses into the RAR's
- *
- * The given list replaces any existing list. Clears the last 15 receive
- * address registers and the multicast table. Uses receive address registers
- * for the first 15 multicast addresses, and hashes the rest into the
- * multicast table.
- *****************************************************************************/
-void
-e1000_mc_addr_list_update(struct e1000_hw *hw,
- uint8_t *mc_addr_list,
- uint32_t mc_addr_count,
- uint32_t pad,
- uint32_t rar_used_count)
-{
- uint32_t hash_value;
- uint32_t i;
+ e1000_get_cable_length(hw, &min_length, &max_length);
- DEBUGFUNC("e1000_mc_addr_list_update");
+ if((hw->dsp_config_state == e1000_dsp_config_enabled) &&
+ min_length >= e1000_igp_cable_length_50) {
+
+ for(i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i],
+ &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX;
+
+ ret_val = e1000_write_phy_reg(hw, dsp_reg_array[i],
+ phy_data);
+ if(ret_val)
+ return ret_val;
+ }
+ hw->dsp_config_state = e1000_dsp_config_activated;
+ }
- /* Set the new number of MC addresses that we are being requested to use. */
- hw->num_mc_addrs = mc_addr_count;
+ if((hw->ffe_config_state == e1000_ffe_config_enabled) &&
+ (min_length < e1000_igp_cable_length_50)) {
- /* Clear RAR[1-15] */
- DEBUGOUT(" Clearing RAR[1-15]\n");
- for(i = rar_used_count; i < E1000_RAR_ENTRIES; i++) {
- E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
- E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
- }
+ uint16_t ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_20;
+ uint32_t idle_errs = 0;
- /* Clear the MTA */
- DEBUGOUT(" Clearing MTA\n");
- for(i = 0; i < E1000_NUM_MTA_REGISTERS; i++) {
- E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
- }
+ /* clear previous idle error counts */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
- /* Add the new addresses */
- for(i = 0; i < mc_addr_count; i++) {
- DEBUGOUT(" Adding the multicast addresses:\n");
- DEBUGOUT7(" MC Addr #%d =%.2X %.2X %.2X %.2X %.2X %.2X\n", i,
- mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad)],
- mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 1],
- mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 2],
- mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 3],
- mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 4],
- mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 5]);
+ for(i = 0; i < ffe_idle_err_timeout; i++) {
+ udelay(1000);
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
- hash_value = e1000_hash_mc_addr(hw,
- mc_addr_list +
- (i * (ETH_LENGTH_OF_ADDRESS + pad)));
+ idle_errs += (phy_data & SR_1000T_IDLE_ERROR_CNT);
+ if(idle_errs > SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT) {
+ hw->ffe_config_state = e1000_ffe_config_active;
- DEBUGOUT1(" Hash value = 0x%03X\n", hash_value);
+ ret_val = e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_DSP_FFE,
+ IGP01E1000_PHY_DSP_FFE_CM_CP);
+ if(ret_val)
+ return ret_val;
+ break;
+ }
- /* Place this multicast address in the RAR if there is room, *
- * else put it in the MTA
- */
- if(rar_used_count < E1000_RAR_ENTRIES) {
- e1000_rar_set(hw,
- mc_addr_list + (i * (ETH_LENGTH_OF_ADDRESS + pad)),
- rar_used_count);
- rar_used_count++;
- } else {
- e1000_mta_set(hw, hash_value);
+ if(idle_errs)
+ ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_100;
+ }
+ }
}
- }
- DEBUGOUT("MC Update Complete\n");
-}
+ } else {
+ if(hw->dsp_config_state == e1000_dsp_config_activated) {
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of the routines. */
+ ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
-/******************************************************************************
- * Hashes an address to determine its location in the multicast table
- *
- * hw - Struct containing variables accessed by shared code
- * mc_addr - the multicast address to hash
- *****************************************************************************/
-uint32_t
-e1000_hash_mc_addr(struct e1000_hw *hw,
- uint8_t *mc_addr)
-{
- uint32_t hash_value = 0;
+ if(ret_val)
+ return ret_val;
- /* The portion of the address that is used for the hash table is
- * determined by the mc_filter_type setting.
- */
- switch (hw->mc_filter_type) {
- /* [0] [1] [2] [3] [4] [5]
- * 01 AA 00 12 34 56
- * LSB MSB
- */
- case 0:
- /* [47:36] i.e. 0x563 for above example address */
- hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4));
- break;
- case 1:
- /* [46:35] i.e. 0xAC6 for above example address */
- hash_value = ((mc_addr[4] >> 3) | (((uint16_t) mc_addr[5]) << 5));
- break;
- case 2:
- /* [45:34] i.e. 0x5D8 for above example address */
- hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6));
- break;
- case 3:
- /* [43:32] i.e. 0x634 for above example address */
- hash_value = ((mc_addr[4]) | (((uint16_t) mc_addr[5]) << 8));
- break;
- }
+ /* Disable the PHY transmitter */
+ ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
- hash_value &= 0xFFF;
- return hash_value;
-}
+ if(ret_val)
+ return ret_val;
-/******************************************************************************
- * Sets the bit in the multicast table corresponding to the hash value.
- *
- * hw - Struct containing variables accessed by shared code
- * hash_value - Multicast address hash value
- *****************************************************************************/
-void
-e1000_mta_set(struct e1000_hw *hw,
- uint32_t hash_value)
-{
- uint32_t hash_bit, hash_reg;
- uint32_t mta;
- uint32_t temp;
+ msec_delay_irq(20);
- /* The MTA is a register array of 128 32-bit registers.
- * It is treated like an array of 4096 bits. We want to set
- * bit BitArray[hash_value]. So we figure out what register
- * the bit is in, read it, OR in the new bit, then write
- * back the new value. The register is determined by the
- * upper 7 bits of the hash value and the bit within that
- * register are determined by the lower 5 bits of the value.
- */
- hash_reg = (hash_value >> 5) & 0x7F;
- hash_bit = hash_value & 0x1F;
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_FORCE_GIGA);
+ if(ret_val)
+ return ret_val;
+ for(i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i], &phy_data);
+ if(ret_val)
+ return ret_val;
- mta = E1000_READ_REG_ARRAY(hw, MTA, hash_reg);
+ phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX;
+ phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS;
- mta |= (1 << hash_bit);
+ ret_val = e1000_write_phy_reg(hw,dsp_reg_array[i], phy_data);
+ if(ret_val)
+ return ret_val;
+ }
- /* If we are on an 82544 and we are trying to write an odd offset
- * in the MTA, save off the previous entry before writing and
- * restore the old value after writing.
- */
- if((hw->mac_type == e1000_82544) && ((hash_reg & 0x1) == 1)) {
- temp = E1000_READ_REG_ARRAY(hw, MTA, (hash_reg - 1));
- E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta);
- E1000_WRITE_REG_ARRAY(hw, MTA, (hash_reg - 1), temp);
- } else {
- E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta);
- }
-}
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_RESTART_AUTONEG);
+ if(ret_val)
+ return ret_val;
-/******************************************************************************
- * Puts an ethernet address into a receive address register.
- *
- * hw - Struct containing variables accessed by shared code
- * addr - Address to put into receive address register
- * index - Receive address register to write
- *****************************************************************************/
-void
-e1000_rar_set(struct e1000_hw *hw,
- uint8_t *addr,
- uint32_t index)
-{
- uint32_t rar_low, rar_high;
+ msec_delay_irq(20);
- /* HW expects these in little endian so we reverse the byte order
- * from network order (big endian) to little endian
- */
- rar_low = ((uint32_t) addr[0] |
- ((uint32_t) addr[1] << 8) |
- ((uint32_t) addr[2] << 16) | ((uint32_t) addr[3] << 24));
+ /* Now enable the transmitter */
+ ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
- rar_high = ((uint32_t) addr[4] | ((uint32_t) addr[5] << 8) | E1000_RAH_AV);
+ if(ret_val)
+ return ret_val;
- E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low);
- E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high);
-}
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+ }
-/******************************************************************************
- * Writes a value to the specified offset in the VLAN filter table.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - Offset in VLAN filer table to write
- * value - Value to write into VLAN filter table
- *****************************************************************************/
-void
-e1000_write_vfta(struct e1000_hw *hw,
- uint32_t offset,
- uint32_t value)
-{
- uint32_t temp;
+ if(hw->ffe_config_state == e1000_ffe_config_active) {
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of the routines. */
+ ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
- if((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) {
- temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1));
- E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
- E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp);
- } else {
- E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
- }
-}
+ if(ret_val)
+ return ret_val;
-/******************************************************************************
- * Clears the VLAN filer table
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-void
-e1000_clear_vfta(struct e1000_hw *hw)
-{
- uint32_t offset;
+ /* Disable the PHY transmitter */
+ ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
- for(offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++)
- E1000_WRITE_REG_ARRAY(hw, VFTA, offset, 0);
-}
+ if(ret_val)
+ return ret_val;
-static int32_t
-e1000_id_led_init(struct e1000_hw * hw)
-{
- uint32_t ledctl;
- const uint32_t ledctl_mask = 0x000000FF;
- const uint32_t ledctl_on = E1000_LEDCTL_MODE_LED_ON;
- const uint32_t ledctl_off = E1000_LEDCTL_MODE_LED_OFF;
- uint16_t eeprom_data, i, temp;
- const uint16_t led_mask = 0x0F;
+ msec_delay_irq(20);
- DEBUGFUNC("e1000_id_led_init");
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_FORCE_GIGA);
+ if(ret_val)
+ return ret_val;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_DSP_FFE,
+ IGP01E1000_PHY_DSP_FFE_DEFAULT);
+ if(ret_val)
+ return ret_val;
- if(hw->mac_type < e1000_82540) {
- /* Nothing to do */
- return E1000_SUCCESS;
- }
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_RESTART_AUTONEG);
+ if(ret_val)
+ return ret_val;
- ledctl = E1000_READ_REG(hw, LEDCTL);
- hw->ledctl_default = ledctl;
- hw->ledctl_mode1 = hw->ledctl_default;
- hw->ledctl_mode2 = hw->ledctl_default;
+ msec_delay_irq(20);
- if(e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- if((eeprom_data== ID_LED_RESERVED_0000) ||
- (eeprom_data == ID_LED_RESERVED_FFFF)) eeprom_data = ID_LED_DEFAULT;
- for(i = 0; i < 4; i++) {
- temp = (eeprom_data >> (i << 2)) & led_mask;
- switch(temp) {
- case ID_LED_ON1_DEF2:
- case ID_LED_ON1_ON2:
- case ID_LED_ON1_OFF2:
- hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
- hw->ledctl_mode1 |= ledctl_on << (i << 3);
- break;
- case ID_LED_OFF1_DEF2:
- case ID_LED_OFF1_ON2:
- case ID_LED_OFF1_OFF2:
- hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
- hw->ledctl_mode1 |= ledctl_off << (i << 3);
- break;
- default:
- /* Do nothing */
- break;
- }
- switch(temp) {
- case ID_LED_DEF1_ON2:
- case ID_LED_ON1_ON2:
- case ID_LED_OFF1_ON2:
- hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
- hw->ledctl_mode2 |= ledctl_on << (i << 3);
- break;
- case ID_LED_DEF1_OFF2:
- case ID_LED_ON1_OFF2:
- case ID_LED_OFF1_OFF2:
- hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
- hw->ledctl_mode2 |= ledctl_off << (i << 3);
- break;
- default:
- /* Do nothing */
- break;
+ /* Now enable the transmitter */
+ ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
+
+ if(ret_val)
+ return ret_val;
+
+ hw->ffe_config_state = e1000_ffe_config_enabled;
}
}
return E1000_SUCCESS;
}
-/******************************************************************************
- * Prepares SW controlable LED for use and saves the current state of the LED.
+/*****************************************************************************
+ * Set PHY to class A mode
+ * Assumes the following operations will follow to enable the new class mode.
+ * 1. Do a PHY soft reset
+ * 2. Restart auto-negotiation or force link.
*
* hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-int32_t
-e1000_setup_led(struct e1000_hw *hw)
+ ****************************************************************************/
+static int32_t
+e1000_set_phy_mode(struct e1000_hw *hw)
{
- uint32_t ledctl;
- int32_t ret_val = E1000_SUCCESS;
+ int32_t ret_val;
+ uint16_t eeprom_data;
- DEBUGFUNC("e1000_setup_led");
+ DEBUGFUNC("e1000_set_phy_mode");
- switch(hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- case e1000_82543:
- case e1000_82544:
- /* No setup necessary */
- break;
- case e1000_82541:
- case e1000_82547:
- case e1000_82541_rev_2:
- case e1000_82547_rev_2:
- /* Turn off PHY Smart Power Down (if enabled) */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO,
- &hw->phy_spd_default);
- if(ret_val)
- return ret_val;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
- (uint16_t)(hw->phy_spd_default &
- ~IGP01E1000_GMII_SPD));
- if(ret_val)
+ if((hw->mac_type == e1000_82545_rev_3) &&
+ (hw->media_type == e1000_media_type_copper)) {
+ ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1, &eeprom_data);
+ if(ret_val) {
return ret_val;
- /* Fall Through */
- default:
- if(hw->media_type == e1000_media_type_fiber) {
- ledctl = E1000_READ_REG(hw, LEDCTL);
- /* Save current LEDCTL settings */
- hw->ledctl_default = ledctl;
- /* Turn off LED0 */
- ledctl &= ~(E1000_LEDCTL_LED0_IVRT |
- E1000_LEDCTL_LED0_BLINK |
- E1000_LEDCTL_LED0_MODE_MASK);
- ledctl |= (E1000_LEDCTL_MODE_LED_OFF <<
- E1000_LEDCTL_LED0_MODE_SHIFT);
- E1000_WRITE_REG(hw, LEDCTL, ledctl);
- } else if(hw->media_type == e1000_media_type_copper)
- E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1);
- break;
+ }
+
+ if((eeprom_data != EEPROM_RESERVED_WORD) &&
+ (eeprom_data & EEPROM_PHY_CLASS_A)) {
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x000B);
+ if(ret_val)
+ return ret_val;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x8104);
+ if(ret_val)
+ return ret_val;
+
+ hw->phy_reset_disable = FALSE;
+ }
}
return E1000_SUCCESS;
}
-/******************************************************************************
- * Restores the saved state of the SW controlable LED.
+/*****************************************************************************
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-int32_t
-e1000_cleanup_led(struct e1000_hw *hw)
+ * This function sets the lplu state according to the active flag. When
+ * activating lplu this function also disables smart speed and vise versa.
+ * lplu will not be activated unless the device autonegotiation advertisment
+ * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * hw: Struct containing variables accessed by shared code
+ * active - true to enable lplu false to disable lplu.
+ *
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * E1000_SUCCESS at any other case.
+ *
+ ****************************************************************************/
+
+static int32_t
+e1000_set_d3_lplu_state(struct e1000_hw *hw,
+ boolean_t active)
{
- int32_t ret_val = E1000_SUCCESS;
+ int32_t ret_val;
+ uint16_t phy_data;
+ DEBUGFUNC("e1000_set_d3_lplu_state");
- DEBUGFUNC("e1000_cleanup_led");
+ if(hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2)
+ return E1000_SUCCESS;
- switch(hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- case e1000_82543:
- case e1000_82544:
- /* No cleanup necessary */
- break;
- case e1000_82541:
- case e1000_82547:
- case e1000_82541_rev_2:
- case e1000_82547_rev_2:
- /* Turn on PHY Smart Power Down (if previously enabled) */
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
- hw->phy_spd_default);
+ /* During driver activity LPLU should not be used or it will attain link
+ * from the lowest speeds starting from 10Mbps. The capability is used for
+ * Dx transitions and states */
+ if(hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data);
+ if(ret_val)
+ return ret_val;
+ } else {
+ ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
if(ret_val)
return ret_val;
- /* Fall Through */
- default:
- /* Restore LEDCTL settings */
- E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_default);
- break;
}
- return E1000_SUCCESS;
-}
-
-/******************************************************************************
- * Turns on the software controllable LED
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-int32_t
-e1000_led_on(struct e1000_hw *hw)
-{
- uint32_t ctrl = E1000_READ_REG(hw, CTRL);
-
- DEBUGFUNC("e1000_led_on");
-
- switch(hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- case e1000_82543:
- /* Set SW Defineable Pin 0 to turn on the LED */
- ctrl |= E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- break;
- case e1000_82544:
- if(hw->media_type == e1000_media_type_fiber) {
- /* Set SW Defineable Pin 0 to turn on the LED */
- ctrl |= E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
+ if(!active) {
+ if(hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
+ if(ret_val)
+ return ret_val;
} else {
- /* Clear SW Defineable Pin 0 to turn on the LED */
- ctrl &= ~E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- }
- break;
- default:
- if(hw->media_type == e1000_media_type_fiber) {
- /* Clear SW Defineable Pin 0 to turn on the LED */
- ctrl &= ~E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- } else if(hw->media_type == e1000_media_type_copper) {
- E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode2);
- return E1000_SUCCESS;
+ phy_data &= ~IGP02E1000_PM_D3_LPLU;
+ ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
+ phy_data);
+ if (ret_val)
+ return ret_val;
}
- break;
- }
- E1000_WRITE_REG(hw, CTRL, ctrl);
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
+ * Dx states where the power conservation is most important. During
+ * driver activity we should enable SmartSpeed, so performance is
+ * maintained. */
+ if (hw->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
- return E1000_SUCCESS;
-}
+ phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if(ret_val)
+ return ret_val;
+ } else if (hw->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
-/******************************************************************************
- * Turns off the software controllable LED
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-int32_t
-e1000_led_off(struct e1000_hw *hw)
-{
- uint32_t ctrl = E1000_READ_REG(hw, CTRL);
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if(ret_val)
+ return ret_val;
+ }
- DEBUGFUNC("e1000_led_off");
+ } else if((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) ||
+ (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL ) ||
+ (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) {
- switch(hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- case e1000_82543:
- /* Clear SW Defineable Pin 0 to turn off the LED */
- ctrl &= ~E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- break;
- case e1000_82544:
- if(hw->media_type == e1000_media_type_fiber) {
- /* Clear SW Defineable Pin 0 to turn off the LED */
- ctrl &= ~E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
+ if(hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data |= IGP01E1000_GMII_FLEX_SPD;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
+ if(ret_val)
+ return ret_val;
} else {
- /* Set SW Defineable Pin 0 to turn off the LED */
- ctrl |= E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- }
- break;
- default:
- if(hw->media_type == e1000_media_type_fiber) {
- /* Set SW Defineable Pin 0 to turn off the LED */
- ctrl |= E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- } else if(hw->media_type == e1000_media_type_copper) {
- E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1);
- return E1000_SUCCESS;
+ phy_data |= IGP02E1000_PM_D3_LPLU;
+ ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
+ phy_data);
+ if (ret_val)
+ return ret_val;
}
- break;
- }
- E1000_WRITE_REG(hw, CTRL, ctrl);
+ /* When LPLU is enabled we should disable SmartSpeed */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data);
+ if(ret_val)
+ return ret_val;
+ }
return E1000_SUCCESS;
}
-/******************************************************************************
- * Clears all hardware statistics counters.
+/*****************************************************************************
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-void
-e1000_clear_hw_cntrs(struct e1000_hw *hw)
-{
- volatile uint32_t temp;
+ * This function sets the lplu d0 state according to the active flag. When
+ * activating lplu this function also disables smart speed and vise versa.
+ * lplu will not be activated unless the device autonegotiation advertisment
+ * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * hw: Struct containing variables accessed by shared code
+ * active - true to enable lplu false to disable lplu.
+ *
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * E1000_SUCCESS at any other case.
+ *
+ ****************************************************************************/
- temp = E1000_READ_REG(hw, CRCERRS);
- temp = E1000_READ_REG(hw, SYMERRS);
- temp = E1000_READ_REG(hw, MPC);
- temp = E1000_READ_REG(hw, SCC);
- temp = E1000_READ_REG(hw, ECOL);
- temp = E1000_READ_REG(hw, MCC);
- temp = E1000_READ_REG(hw, LATECOL);
- temp = E1000_READ_REG(hw, COLC);
- temp = E1000_READ_REG(hw, DC);
- temp = E1000_READ_REG(hw, SEC);
- temp = E1000_READ_REG(hw, RLEC);
- temp = E1000_READ_REG(hw, XONRXC);
- temp = E1000_READ_REG(hw, XONTXC);
- temp = E1000_READ_REG(hw, XOFFRXC);
- temp = E1000_READ_REG(hw, XOFFTXC);
- temp = E1000_READ_REG(hw, FCRUC);
- temp = E1000_READ_REG(hw, PRC64);
- temp = E1000_READ_REG(hw, PRC127);
- temp = E1000_READ_REG(hw, PRC255);
- temp = E1000_READ_REG(hw, PRC511);
- temp = E1000_READ_REG(hw, PRC1023);
- temp = E1000_READ_REG(hw, PRC1522);
- temp = E1000_READ_REG(hw, GPRC);
- temp = E1000_READ_REG(hw, BPRC);
- temp = E1000_READ_REG(hw, MPRC);
- temp = E1000_READ_REG(hw, GPTC);
- temp = E1000_READ_REG(hw, GORCL);
- temp = E1000_READ_REG(hw, GORCH);
- temp = E1000_READ_REG(hw, GOTCL);
- temp = E1000_READ_REG(hw, GOTCH);
- temp = E1000_READ_REG(hw, RNBC);
- temp = E1000_READ_REG(hw, RUC);
- temp = E1000_READ_REG(hw, RFC);
- temp = E1000_READ_REG(hw, ROC);
- temp = E1000_READ_REG(hw, RJC);
- temp = E1000_READ_REG(hw, TORL);
- temp = E1000_READ_REG(hw, TORH);
- temp = E1000_READ_REG(hw, TOTL);
- temp = E1000_READ_REG(hw, TOTH);
- temp = E1000_READ_REG(hw, TPR);
- temp = E1000_READ_REG(hw, TPT);
- temp = E1000_READ_REG(hw, PTC64);
- temp = E1000_READ_REG(hw, PTC127);
- temp = E1000_READ_REG(hw, PTC255);
- temp = E1000_READ_REG(hw, PTC511);
- temp = E1000_READ_REG(hw, PTC1023);
- temp = E1000_READ_REG(hw, PTC1522);
- temp = E1000_READ_REG(hw, MPTC);
- temp = E1000_READ_REG(hw, BPTC);
+static int32_t
+e1000_set_d0_lplu_state(struct e1000_hw *hw,
+ boolean_t active)
+{
+ int32_t ret_val;
+ uint16_t phy_data;
+ DEBUGFUNC("e1000_set_d0_lplu_state");
- if(hw->mac_type < e1000_82543) return;
+ if(hw->mac_type <= e1000_82547_rev_2)
+ return E1000_SUCCESS;
- temp = E1000_READ_REG(hw, ALGNERRC);
- temp = E1000_READ_REG(hw, RXERRC);
- temp = E1000_READ_REG(hw, TNCRS);
- temp = E1000_READ_REG(hw, CEXTERR);
- temp = E1000_READ_REG(hw, TSCTC);
- temp = E1000_READ_REG(hw, TSCTFC);
+ ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
+ if(ret_val)
+ return ret_val;
- if(hw->mac_type <= e1000_82544) return;
+ if (!active) {
+ phy_data &= ~IGP02E1000_PM_D0_LPLU;
+ ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
+ if (ret_val)
+ return ret_val;
- temp = E1000_READ_REG(hw, MGTPRC);
- temp = E1000_READ_REG(hw, MGTPDC);
- temp = E1000_READ_REG(hw, MGTPTC);
-}
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
+ * Dx states where the power conservation is most important. During
+ * driver activity we should enable SmartSpeed, so performance is
+ * maintained. */
+ if (hw->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
-/******************************************************************************
- * Resets Adaptive IFS to its default state.
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Call this after e1000_init_hw. You may override the IFS defaults by setting
- * hw->ifs_params_forced to TRUE. However, you must initialize hw->
- * current_ifs_val, ifs_min_val, ifs_max_val, ifs_step_size, and ifs_ratio
- * before calling this function.
- *****************************************************************************/
-void
-e1000_reset_adaptive(struct e1000_hw *hw)
-{
- DEBUGFUNC("e1000_reset_adaptive");
+ phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if(ret_val)
+ return ret_val;
+ } else if (hw->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
- if(hw->adaptive_ifs) {
- if(!hw->ifs_params_forced) {
- hw->current_ifs_val = 0;
- hw->ifs_min_val = IFS_MIN;
- hw->ifs_max_val = IFS_MAX;
- hw->ifs_step_size = IFS_STEP;
- hw->ifs_ratio = IFS_RATIO;
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if(ret_val)
+ return ret_val;
}
- hw->in_ifs_mode = FALSE;
- E1000_WRITE_REG(hw, AIT, 0);
+
+
} else {
- DEBUGOUT("Not in Adaptive IFS mode!\n");
+
+ phy_data |= IGP02E1000_PM_D0_LPLU;
+ ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* When LPLU is enabled we should disable SmartSpeed */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data);
+ if(ret_val)
+ return ret_val;
+
}
+ return E1000_SUCCESS;
}
/******************************************************************************
- * Called during the callback/watchdog routine to update IFS value based on
- * the ratio of transmits to collisions.
+ * Change VCO speed register to improve Bit Error Rate performance of SERDES.
*
* hw - Struct containing variables accessed by shared code
- * tx_packets - Number of transmits since last callback
- * total_collisions - Number of collisions since last callback
*****************************************************************************/
-void
-e1000_update_adaptive(struct e1000_hw *hw)
+static int32_t
+e1000_set_vco_speed(struct e1000_hw *hw)
{
- DEBUGFUNC("e1000_update_adaptive");
+ int32_t ret_val;
+ uint16_t default_page = 0;
+ uint16_t phy_data;
- if(hw->adaptive_ifs) {
- if((hw->collision_delta * hw->ifs_ratio) > hw->tx_packet_delta) {
- if(hw->tx_packet_delta > MIN_NUM_XMITS) {
- hw->in_ifs_mode = TRUE;
- if(hw->current_ifs_val < hw->ifs_max_val) {
- if(hw->current_ifs_val == 0)
- hw->current_ifs_val = hw->ifs_min_val;
- else
- hw->current_ifs_val += hw->ifs_step_size;
- E1000_WRITE_REG(hw, AIT, hw->current_ifs_val);
- }
- }
- } else {
- if(hw->in_ifs_mode && (hw->tx_packet_delta <= MIN_NUM_XMITS)) {
- hw->current_ifs_val = 0;
- hw->in_ifs_mode = FALSE;
- E1000_WRITE_REG(hw, AIT, 0);
- }
- }
- } else {
- DEBUGOUT("Not in Adaptive IFS mode!\n");
+ DEBUGFUNC("e1000_set_vco_speed");
+
+ switch(hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
+ return E1000_SUCCESS;
}
+
+ /* Set PHY register 30, page 5, bit 8 to 0 */
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page);
+ if(ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005);
+ if(ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data &= ~M88E1000_PHY_VCO_REG_BIT8;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
+ if(ret_val)
+ return ret_val;
+
+ /* Set PHY register 30, page 4, bit 11 to 1 */
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004);
+ if(ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PHY_VCO_REG_BIT11;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
+ if(ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, default_page);
+ if(ret_val)
+ return ret_val;
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT
+
+/*****************************************************************************
+ * This function reads the cookie from ARC ram.
*
- * hw - Struct containing variables accessed by shared code
- * frame_len - The length of the frame in question
- * mac_addr - The Ethernet destination address of the frame in question
- *****************************************************************************/
-void
-e1000_tbi_adjust_stats(struct e1000_hw *hw,
- struct e1000_hw_stats *stats,
- uint32_t frame_len,
- uint8_t *mac_addr)
+ * returns: - E1000_SUCCESS .
+ ****************************************************************************/
+int32_t
+e1000_host_if_read_cookie(struct e1000_hw * hw, uint8_t *buffer)
{
- uint64_t carry_bit;
+ uint8_t i;
+ uint32_t offset = E1000_MNG_DHCP_COOKIE_OFFSET;
+ uint8_t length = E1000_MNG_DHCP_COOKIE_LENGTH;
- /* First adjust the frame length. */
- frame_len--;
- /* We need to adjust the statistics counters, since the hardware
- * counters overcount this packet as a CRC error and undercount
- * the packet as a good packet
- */
- /* This packet should not be counted as a CRC error. */
- stats->crcerrs--;
- /* This packet does count as a Good Packet Received. */
- stats->gprc++;
+ length = (length >> 2);
+ offset = (offset >> 2);
- /* Adjust the Good Octets received counters */
- carry_bit = 0x80000000 & stats->gorcl;
- stats->gorcl += frame_len;
- /* If the high bit of Gorcl (the low 32 bits of the Good Octets
- * Received Count) was one before the addition,
- * AND it is zero after, then we lost the carry out,
- * need to add one to Gorch (Good Octets Received Count High).
- * This could be simplified if all environments supported
- * 64-bit integers.
- */
- if(carry_bit && ((stats->gorcl & 0x80000000) == 0))
- stats->gorch++;
- /* Is this a broadcast or multicast? Check broadcast first,
- * since the test for a multicast frame will test positive on
- * a broadcast frame.
- */
- if((mac_addr[0] == (uint8_t) 0xff) && (mac_addr[1] == (uint8_t) 0xff))
- /* Broadcast packet */
- stats->bprc++;
- else if(*mac_addr & 0x01)
- /* Multicast packet */
- stats->mprc++;
+ for (i = 0; i < length; i++) {
+ *((uint32_t *) buffer + i) =
+ E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset + i);
+ }
+ return E1000_SUCCESS;
+}
- if(frame_len == hw->max_frame_size) {
- /* In this case, the hardware has overcounted the number of
- * oversize frames.
- */
- if(stats->roc > 0)
- stats->roc--;
+
+/*****************************************************************************
+ * This function checks whether the HOST IF is enabled for command operaton
+ * and also checks whether the previous command is completed.
+ * It busy waits in case of previous command is not completed.
+ *
+ * returns: - E1000_ERR_HOST_INTERFACE_COMMAND in case if is not ready or
+ * timeout
+ * - E1000_SUCCESS for success.
+ ****************************************************************************/
+static int32_t
+e1000_mng_enable_host_if(struct e1000_hw * hw)
+{
+ uint32_t hicr;
+ uint8_t i;
+
+ /* Check that the host interface is enabled. */
+ hicr = E1000_READ_REG(hw, HICR);
+ if ((hicr & E1000_HICR_EN) == 0) {
+ DEBUGOUT("E1000_HOST_EN bit disabled.\n");
+ return -E1000_ERR_HOST_INTERFACE_COMMAND;
+ }
+ /* check the previous command is completed */
+ for (i = 0; i < E1000_MNG_DHCP_COMMAND_TIMEOUT; i++) {
+ hicr = E1000_READ_REG(hw, HICR);
+ if (!(hicr & E1000_HICR_C))
+ break;
+ msec_delay_irq(1);
}
- /* Adjust the bin counters when the extra byte put the frame in the
- * wrong bin. Remember that the frame_len was adjusted above.
- */
- if(frame_len == 64) {
- stats->prc64++;
- stats->prc127--;
- } else if(frame_len == 127) {
- stats->prc127++;
- stats->prc255--;
- } else if(frame_len == 255) {
- stats->prc255++;
- stats->prc511--;
- } else if(frame_len == 511) {
- stats->prc511++;
- stats->prc1023--;
- } else if(frame_len == 1023) {
- stats->prc1023++;
- stats->prc1522--;
- } else if(frame_len == 1522) {
- stats->prc1522++;
+ if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) {
+ DEBUGOUT("Previous command timeout failed .\n");
+ return -E1000_ERR_HOST_INTERFACE_COMMAND;
}
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Gets the current PCI bus type, speed, and width of the hardware
+/*****************************************************************************
+ * This function writes the buffer content at the offset given on the host if.
+ * It also does alignment considerations to do the writes in most efficient way.
+ * Also fills up the sum of the buffer in *buffer parameter.
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-void
-e1000_get_bus_info(struct e1000_hw *hw)
+ * returns - E1000_SUCCESS for success.
+ ****************************************************************************/
+static int32_t
+e1000_mng_host_if_write(struct e1000_hw * hw, uint8_t *buffer,
+ uint16_t length, uint16_t offset, uint8_t *sum)
{
- uint32_t status;
+ uint8_t *tmp;
+ uint8_t *bufptr = buffer;
+ uint32_t data;
+ uint16_t remaining, i, j, prev_bytes;
- if(hw->mac_type < e1000_82543) {
- hw->bus_type = e1000_bus_type_unknown;
- hw->bus_speed = e1000_bus_speed_unknown;
- hw->bus_width = e1000_bus_width_unknown;
- return;
+ /* sum = only sum of the data and it is not checksum */
+
+ if (length == 0 || offset + length > E1000_HI_MAX_MNG_DATA_LENGTH) {
+ return -E1000_ERR_PARAM;
}
- status = E1000_READ_REG(hw, STATUS);
- hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ?
- e1000_bus_type_pcix : e1000_bus_type_pci;
-
- if(hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) {
- hw->bus_speed = (hw->bus_type == e1000_bus_type_pci) ?
- e1000_bus_speed_66 : e1000_bus_speed_120;
- } else if(hw->bus_type == e1000_bus_type_pci) {
- hw->bus_speed = (status & E1000_STATUS_PCI66) ?
- e1000_bus_speed_66 : e1000_bus_speed_33;
- } else {
- switch (status & E1000_STATUS_PCIX_SPEED) {
- case E1000_STATUS_PCIX_SPEED_66:
- hw->bus_speed = e1000_bus_speed_66;
- break;
- case E1000_STATUS_PCIX_SPEED_100:
- hw->bus_speed = e1000_bus_speed_100;
- break;
- case E1000_STATUS_PCIX_SPEED_133:
- hw->bus_speed = e1000_bus_speed_133;
- break;
- default:
- hw->bus_speed = e1000_bus_speed_reserved;
- break;
+ tmp = (uint8_t *)&data;
+ prev_bytes = offset & 0x3;
+ offset &= 0xFFFC;
+ offset >>= 2;
+
+ if (prev_bytes) {
+ data = E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset);
+ for (j = prev_bytes; j < sizeof(uint32_t); j++) {
+ *(tmp + j) = *bufptr++;
+ *sum += *(tmp + j);
+ }
+ E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset, data);
+ length -= j - prev_bytes;
+ offset++;
+ }
+
+ remaining = length & 0x3;
+ length -= remaining;
+
+ /* Calculate length in DWORDs */
+ length >>= 2;
+
+ /* The device driver writes the relevant command block into the
+ * ram area. */
+ for (i = 0; i < length; i++) {
+ for (j = 0; j < sizeof(uint32_t); j++) {
+ *(tmp + j) = *bufptr++;
+ *sum += *(tmp + j);
+ }
+
+ E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data);
+ }
+ if (remaining) {
+ for (j = 0; j < sizeof(uint32_t); j++) {
+ if (j < remaining)
+ *(tmp + j) = *bufptr++;
+ else
+ *(tmp + j) = 0;
+
+ *sum += *(tmp + j);
}
+ E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data);
}
- hw->bus_width = (status & E1000_STATUS_BUS64) ?
- e1000_bus_width_64 : e1000_bus_width_32;
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Reads a value from one of the devices registers using port I/O (as opposed
- * memory mapped I/O). Only 82544 and newer devices support port I/O.
+
+
+/*****************************************************************************
+ * This function writes the command header after does the checksum calculation.
*
- * hw - Struct containing variables accessed by shared code
- * offset - offset to read from
- *****************************************************************************/
-uint32_t
-e1000_read_reg_io(struct e1000_hw *hw,
- uint32_t offset)
+ * returns - E1000_SUCCESS for success.
+ ****************************************************************************/
+static int32_t
+e1000_mng_write_cmd_header(struct e1000_hw * hw,
+ struct e1000_host_mng_command_header * hdr)
{
- unsigned long io_addr = hw->io_base;
- unsigned long io_data = hw->io_base + 4;
+ uint16_t i;
+ uint8_t sum;
+ uint8_t *buffer;
- e1000_io_write(hw, io_addr, offset);
- return e1000_io_read(hw, io_data);
+ /* Write the whole command header structure which includes sum of
+ * the buffer */
+
+ uint16_t length = sizeof(struct e1000_host_mng_command_header);
+
+ sum = hdr->checksum;
+ hdr->checksum = 0;
+
+ buffer = (uint8_t *) hdr;
+ i = length;
+ while(i--)
+ sum += buffer[i];
+
+ hdr->checksum = 0 - sum;
+
+ length >>= 2;
+ /* The device driver writes the relevant command block into the ram area. */
+ for (i = 0; i < length; i++)
+ E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, i, *((uint32_t *) hdr + i));
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Writes a value to one of the devices registers using port I/O (as opposed to
- * memory mapped I/O). Only 82544 and newer devices support port I/O.
+
+/*****************************************************************************
+ * This function indicates to ARC that a new command is pending which completes
+ * one write operation by the driver.
*
- * hw - Struct containing variables accessed by shared code
- * offset - offset to write to
- * value - value to write
- *****************************************************************************/
-void
-e1000_write_reg_io(struct e1000_hw *hw,
- uint32_t offset,
- uint32_t value)
+ * returns - E1000_SUCCESS for success.
+ ****************************************************************************/
+static int32_t
+e1000_mng_write_commit(
+ struct e1000_hw * hw)
{
- unsigned long io_addr = hw->io_base;
- unsigned long io_data = hw->io_base + 4;
+ uint32_t hicr;
- e1000_io_write(hw, io_addr, offset);
- e1000_io_write(hw, io_data, value);
+ hicr = E1000_READ_REG(hw, HICR);
+ /* Setting this bit tells the ARC that a new command is pending. */
+ E1000_WRITE_REG(hw, HICR, hicr | E1000_HICR_C);
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Estimates the cable length.
- *
- * hw - Struct containing variables accessed by shared code
- * min_length - The estimated minimum length
- * max_length - The estimated maximum length
- *
- * returns: - E1000_ERR_XXX
- * E1000_SUCCESS
+/*****************************************************************************
+ * This function checks the mode of the firmware.
*
- * This function always returns a ranged length (minimum & maximum).
- * So for M88 phy's, this function interprets the one value returned from the
- * register to the minimum and maximum range.
- * For IGP phy's, the function calculates the range by the AGC registers.
- *****************************************************************************/
-int32_t
-e1000_get_cable_length(struct e1000_hw *hw,
- uint16_t *min_length,
- uint16_t *max_length)
+ * returns - TRUE when the mode is IAMT or FALSE.
+ ****************************************************************************/
+boolean_t
+e1000_check_mng_mode(
+ struct e1000_hw *hw)
{
- int32_t ret_val;
- uint16_t agc_value = 0;
- uint16_t cur_agc, min_agc = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
- uint16_t i, phy_data;
+ uint32_t fwsm;
- DEBUGFUNC("e1000_get_cable_length");
+ fwsm = E1000_READ_REG(hw, FWSM);
- *min_length = *max_length = 0;
+ if((fwsm & E1000_FWSM_MODE_MASK) ==
+ (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
+ return TRUE;
- /* Use old method for Phy older than IGP */
- if(hw->phy_type == e1000_phy_m88) {
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
- &phy_data);
- if(ret_val)
- return ret_val;
+ return FALSE;
+}
- /* Convert the enum value to ranged values */
- switch((phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
- M88E1000_PSSR_CABLE_LENGTH_SHIFT) {
- case e1000_cable_length_50:
- *min_length = 0;
- *max_length = e1000_igp_cable_length_50;
- break;
- case e1000_cable_length_50_80:
- *min_length = e1000_igp_cable_length_50;
- *max_length = e1000_igp_cable_length_80;
- break;
- case e1000_cable_length_80_110:
- *min_length = e1000_igp_cable_length_80;
- *max_length = e1000_igp_cable_length_110;
- break;
- case e1000_cable_length_110_140:
- *min_length = e1000_igp_cable_length_110;
- *max_length = e1000_igp_cable_length_140;
- break;
- case e1000_cable_length_140:
- *min_length = e1000_igp_cable_length_140;
- *max_length = e1000_igp_cable_length_170;
- break;
- default:
- return -E1000_ERR_PHY;
- break;
- }
- } else if(hw->phy_type == e1000_phy_igp) { /* For IGP PHY */
- uint16_t agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
- {IGP01E1000_PHY_AGC_A,
- IGP01E1000_PHY_AGC_B,
- IGP01E1000_PHY_AGC_C,
- IGP01E1000_PHY_AGC_D};
- /* Read the AGC registers for all channels */
- for(i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
- ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data);
- if(ret_val)
- return ret_val;
+/*****************************************************************************
+ * This function writes the dhcp info .
+ ****************************************************************************/
+int32_t
+e1000_mng_write_dhcp_info(struct e1000_hw * hw, uint8_t *buffer,
+ uint16_t length)
+{
+ int32_t ret_val;
+ struct e1000_host_mng_command_header hdr;
+
+ hdr.command_id = E1000_MNG_DHCP_TX_PAYLOAD_CMD;
+ hdr.command_length = length;
+ hdr.reserved1 = 0;
+ hdr.reserved2 = 0;
+ hdr.checksum = 0;
+
+ ret_val = e1000_mng_enable_host_if(hw);
+ if (ret_val == E1000_SUCCESS) {
+ ret_val = e1000_mng_host_if_write(hw, buffer, length, sizeof(hdr),
+ &(hdr.checksum));
+ if (ret_val == E1000_SUCCESS) {
+ ret_val = e1000_mng_write_cmd_header(hw, &hdr);
+ if (ret_val == E1000_SUCCESS)
+ ret_val = e1000_mng_write_commit(hw);
+ }
+ }
+ return ret_val;
+}
- cur_agc = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT;
- /* Array bound check. */
- if((cur_agc >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) ||
- (cur_agc == 0))
- return -E1000_ERR_PHY;
+/*****************************************************************************
+ * This function calculates the checksum.
+ *
+ * returns - checksum of buffer contents.
+ ****************************************************************************/
+uint8_t
+e1000_calculate_mng_checksum(char *buffer, uint32_t length)
+{
+ uint8_t sum = 0;
+ uint32_t i;
- agc_value += cur_agc;
+ if (!buffer)
+ return 0;
- /* Update minimal AGC value. */
- if(min_agc > cur_agc)
- min_agc = cur_agc;
- }
+ for (i=0; i < length; i++)
+ sum += buffer[i];
- /* Remove the minimal AGC result for length < 50m */
- if(agc_value < IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) {
- agc_value -= min_agc;
+ return (uint8_t) (0 - sum);
+}
- /* Get the average length of the remaining 3 channels */
- agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1);
- } else {
- /* Get the average length of all the 4 channels. */
- agc_value /= IGP01E1000_PHY_CHANNEL_NUM;
+/*****************************************************************************
+ * This function checks whether tx pkt filtering needs to be enabled or not.
+ *
+ * returns - TRUE for packet filtering or FALSE.
+ ****************************************************************************/
+boolean_t
+e1000_enable_tx_pkt_filtering(struct e1000_hw *hw)
+{
+ /* called in init as well as watchdog timer functions */
+
+ int32_t ret_val, checksum;
+ boolean_t tx_filter = FALSE;
+ struct e1000_host_mng_dhcp_cookie *hdr = &(hw->mng_cookie);
+ uint8_t *buffer = (uint8_t *) &(hw->mng_cookie);
+
+ if (e1000_check_mng_mode(hw)) {
+ ret_val = e1000_mng_enable_host_if(hw);
+ if (ret_val == E1000_SUCCESS) {
+ ret_val = e1000_host_if_read_cookie(hw, buffer);
+ if (ret_val == E1000_SUCCESS) {
+ checksum = hdr->checksum;
+ hdr->checksum = 0;
+ if ((hdr->signature == E1000_IAMT_SIGNATURE) &&
+ checksum == e1000_calculate_mng_checksum((char *)buffer,
+ E1000_MNG_DHCP_COOKIE_LENGTH)) {
+ if (hdr->status &
+ E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT)
+ tx_filter = TRUE;
+ } else
+ tx_filter = TRUE;
+ } else
+ tx_filter = TRUE;
}
-
- /* Set the range of the calculated length. */
- *min_length = ((e1000_igp_cable_length_table[agc_value] -
- IGP01E1000_AGC_RANGE) > 0) ?
- (e1000_igp_cable_length_table[agc_value] -
- IGP01E1000_AGC_RANGE) : 0;
- *max_length = e1000_igp_cable_length_table[agc_value] +
- IGP01E1000_AGC_RANGE;
}
- return E1000_SUCCESS;
+ hw->tx_pkt_filtering = tx_filter;
+ return tx_filter;
}
/******************************************************************************
- * Check the cable polarity
+ * Verifies the hardware needs to allow ARPs to be processed by the host
*
* hw - Struct containing variables accessed by shared code
- * polarity - output parameter : 0 - Polarity is not reversed
- * 1 - Polarity is reversed.
*
- * returns: - E1000_ERR_XXX
- * E1000_SUCCESS
+ * returns: - TRUE/FALSE
*
- * For phy's older then IGP, this function simply reads the polarity bit in the
- * Phy Status register. For IGP phy's, this bit is valid only if link speed is
- * 10 Mbps. If the link speed is 100 Mbps there is no polarity so this bit will
- * return 0. If the link speed is 1000 Mbps the polarity status is in the
- * IGP01E1000_PHY_PCS_INIT_REG.
*****************************************************************************/
-int32_t
-e1000_check_polarity(struct e1000_hw *hw,
- uint16_t *polarity)
+uint32_t
+e1000_enable_mng_pass_thru(struct e1000_hw *hw)
+{
+ uint32_t manc;
+ uint32_t fwsm, factps;
+
+ if (hw->asf_firmware_present) {
+ manc = E1000_READ_REG(hw, MANC);
+
+ if (!(manc & E1000_MANC_RCV_TCO_EN) ||
+ !(manc & E1000_MANC_EN_MAC_ADDR_FILTER))
+ return FALSE;
+ if (e1000_arc_subsystem_valid(hw) == TRUE) {
+ fwsm = E1000_READ_REG(hw, FWSM);
+ factps = E1000_READ_REG(hw, FACTPS);
+
+ if (((fwsm & E1000_FWSM_MODE_MASK) ==
+ (e1000_mng_mode_pt << E1000_FWSM_MODE_SHIFT)) &&
+ (factps & E1000_FACTPS_MNGCG))
+ return TRUE;
+ } else
+ if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN))
+ return TRUE;
+ }
+ return FALSE;
+}
+
+static int32_t
+e1000_polarity_reversal_workaround(struct e1000_hw *hw)
{
int32_t ret_val;
- uint16_t phy_data;
+ uint16_t mii_status_reg;
+ uint16_t i;
- DEBUGFUNC("e1000_check_polarity");
+ /* Polarity reversal workaround for forced 10F/10H links. */
- if(hw->phy_type == e1000_phy_m88) {
- /* return the Polarity bit in the Status register. */
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
- &phy_data);
+ /* Disable the transmitter on the PHY */
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
+ if(ret_val)
+ return ret_val;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF);
+ if(ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
+ if(ret_val)
+ return ret_val;
+
+ /* This loop will early-out if the NO link condition has been met. */
+ for(i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Link Status bit
+ * to be clear.
+ */
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
if(ret_val)
return ret_val;
- *polarity = (phy_data & M88E1000_PSSR_REV_POLARITY) >>
- M88E1000_PSSR_REV_POLARITY_SHIFT;
- } else if(hw->phy_type == e1000_phy_igp) {
- /* Read the Status register to check the speed */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
- &phy_data);
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
if(ret_val)
return ret_val;
- /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to
- * find the polarity status */
- if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
- IGP01E1000_PSSR_SPEED_1000MBPS) {
+ if((mii_status_reg & ~MII_SR_LINK_STATUS) == 0) break;
+ msec_delay_irq(100);
+ }
- /* Read the GIG initialization PCS register (0x00B4) */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG,
- &phy_data);
- if(ret_val)
- return ret_val;
+ /* Recommended delay time after link has been lost */
+ msec_delay_irq(1000);
- /* Check the polarity bits */
- *polarity = (phy_data & IGP01E1000_PHY_POLARITY_MASK) ? 1 : 0;
- } else {
- /* For 10 Mbps, read the polarity bit in the status register. (for
- * 100 Mbps this bit is always 0) */
- *polarity = phy_data & IGP01E1000_PSSR_POLARITY_REVERSED;
- }
- }
- return E1000_SUCCESS;
-}
+ /* Now we will re-enable th transmitter on the PHY */
-/******************************************************************************
- * Check if Downshift occured
- *
- * hw - Struct containing variables accessed by shared code
- * downshift - output parameter : 0 - No Downshift ocured.
- * 1 - Downshift ocured.
- *
- * returns: - E1000_ERR_XXX
- * E1000_SUCCESS
- *
- * For phy's older then IGP, this function reads the Downshift bit in the Phy
- * Specific Status register. For IGP phy's, it reads the Downgrade bit in the
- * Link Health register. In IGP this bit is latched high, so the driver must
- * read it immediately after link is established.
- *****************************************************************************/
-int32_t
-e1000_check_downshift(struct e1000_hw *hw)
-{
- int32_t ret_val;
- uint16_t phy_data;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
+ if(ret_val)
+ return ret_val;
+ msec_delay_irq(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0);
+ if(ret_val)
+ return ret_val;
+ msec_delay_irq(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00);
+ if(ret_val)
+ return ret_val;
+ msec_delay_irq(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000);
+ if(ret_val)
+ return ret_val;
- DEBUGFUNC("e1000_check_downshift");
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
+ if(ret_val)
+ return ret_val;
- if(hw->phy_type == e1000_phy_igp) {
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
- &phy_data);
+ /* This loop will early-out if the link condition has been met. */
+ for(i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Link Status bit
+ * to be set.
+ */
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
if(ret_val)
return ret_val;
- hw->speed_downgraded = (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0;
- }
- else if(hw->phy_type == e1000_phy_m88) {
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
- &phy_data);
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
if(ret_val)
return ret_val;
- hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >>
- M88E1000_PSSR_DOWNSHIFT_SHIFT;
+ if(mii_status_reg & MII_SR_LINK_STATUS) break;
+ msec_delay_irq(100);
}
return E1000_SUCCESS;
}
-/*****************************************************************************
+/***************************************************************************
*
- * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a
- * gigabit link is achieved to improve link quality.
+ * Disables PCI-Express master access.
*
* hw: Struct containing variables accessed by shared code
*
- * returns: - E1000_ERR_PHY if fail to read/write the PHY
- * E1000_SUCCESS at any other case.
+ * returns: - none.
*
- ****************************************************************************/
-
-int32_t
-e1000_config_dsp_after_link_change(struct e1000_hw *hw,
- boolean_t link_up)
+ ***************************************************************************/
+static void
+e1000_set_pci_express_master_disable(struct e1000_hw *hw)
{
- int32_t ret_val;
- uint16_t phy_data, speed, duplex, i;
- uint16_t dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
- {IGP01E1000_PHY_AGC_PARAM_A,
- IGP01E1000_PHY_AGC_PARAM_B,
- IGP01E1000_PHY_AGC_PARAM_C,
- IGP01E1000_PHY_AGC_PARAM_D};
- uint16_t min_length, max_length;
-
- DEBUGFUNC("e1000_config_dsp_after_link_change");
-
- if(hw->phy_type != e1000_phy_igp)
- return E1000_SUCCESS;
-
- if(link_up) {
- ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
- if(ret_val) {
- DEBUGOUT("Error getting link speed and duplex\n");
- return ret_val;
- }
-
- if(speed == SPEED_1000) {
-
- e1000_get_cable_length(hw, &min_length, &max_length);
-
- if((hw->dsp_config_state == e1000_dsp_config_enabled) &&
- min_length >= e1000_igp_cable_length_50) {
-
- for(i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
- ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i],
- &phy_data);
- if(ret_val)
- return ret_val;
+ uint32_t ctrl;
- phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX;
+ DEBUGFUNC("e1000_set_pci_express_master_disable");
- ret_val = e1000_write_phy_reg(hw, dsp_reg_array[i],
- phy_data);
- if(ret_val)
- return ret_val;
- }
- hw->dsp_config_state = e1000_dsp_config_activated;
- }
+ if (hw->bus_type != e1000_bus_type_pci_express)
+ return;
- if((hw->ffe_config_state == e1000_ffe_config_enabled) &&
- (min_length < e1000_igp_cable_length_50)) {
+ ctrl = E1000_READ_REG(hw, CTRL);
+ ctrl |= E1000_CTRL_GIO_MASTER_DISABLE;
+ E1000_WRITE_REG(hw, CTRL, ctrl);
+}
- uint16_t ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_20;
- uint32_t idle_errs = 0;
+#if 0
+/***************************************************************************
+ *
+ * Enables PCI-Express master access.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - none.
+ *
+ ***************************************************************************/
+void
+e1000_enable_pciex_master(struct e1000_hw *hw)
+{
+ uint32_t ctrl;
- /* clear previous idle error counts */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS,
- &phy_data);
- if(ret_val)
- return ret_val;
+ DEBUGFUNC("e1000_enable_pciex_master");
- for(i = 0; i < ffe_idle_err_timeout; i++) {
- udelay(1000);
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS,
- &phy_data);
- if(ret_val)
- return ret_val;
+ if (hw->bus_type != e1000_bus_type_pci_express)
+ return;
- idle_errs += (phy_data & SR_1000T_IDLE_ERROR_CNT);
- if(idle_errs > SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT) {
- hw->ffe_config_state = e1000_ffe_config_active;
+ ctrl = E1000_READ_REG(hw, CTRL);
+ ctrl &= ~E1000_CTRL_GIO_MASTER_DISABLE;
+ E1000_WRITE_REG(hw, CTRL, ctrl);
+}
+#endif /* 0 */
- ret_val = e1000_write_phy_reg(hw,
- IGP01E1000_PHY_DSP_FFE,
- IGP01E1000_PHY_DSP_FFE_CM_CP);
- if(ret_val)
- return ret_val;
- break;
- }
+/*******************************************************************************
+ *
+ * Disables PCI-Express master access and verifies there are no pending requests
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_MASTER_REQUESTS_PENDING if master disable bit hasn't
+ * caused the master requests to be disabled.
+ * E1000_SUCCESS master requests disabled.
+ *
+ ******************************************************************************/
+int32_t
+e1000_disable_pciex_master(struct e1000_hw *hw)
+{
+ int32_t timeout = MASTER_DISABLE_TIMEOUT; /* 80ms */
- if(idle_errs)
- ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_100;
- }
- }
- }
- } else {
- if(hw->dsp_config_state == e1000_dsp_config_activated) {
- ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_FORCE_GIGA);
- if(ret_val)
- return ret_val;
- for(i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
- ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i], &phy_data);
- if(ret_val)
- return ret_val;
+ DEBUGFUNC("e1000_disable_pciex_master");
- phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX;
- phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS;
+ if (hw->bus_type != e1000_bus_type_pci_express)
+ return E1000_SUCCESS;
- ret_val = e1000_write_phy_reg(hw,dsp_reg_array[i], phy_data);
- if(ret_val)
- return ret_val;
- }
+ e1000_set_pci_express_master_disable(hw);
- ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_RESTART_AUTONEG);
- if(ret_val)
- return ret_val;
+ while(timeout) {
+ if(!(E1000_READ_REG(hw, STATUS) & E1000_STATUS_GIO_MASTER_ENABLE))
+ break;
+ else
+ udelay(100);
+ timeout--;
+ }
- hw->dsp_config_state = e1000_dsp_config_enabled;
- }
+ if(!timeout) {
+ DEBUGOUT("Master requests are pending.\n");
+ return -E1000_ERR_MASTER_REQUESTS_PENDING;
+ }
- if(hw->ffe_config_state == e1000_ffe_config_active) {
- ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_FORCE_GIGA);
- if(ret_val)
- return ret_val;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_DSP_FFE,
- IGP01E1000_PHY_DSP_FFE_DEFAULT);
- if(ret_val)
- return ret_val;
+ return E1000_SUCCESS;
+}
- ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_RESTART_AUTONEG);
- if(ret_val)
- return ret_val;
- hw->ffe_config_state = e1000_ffe_config_enabled;
+/*******************************************************************************
+ *
+ * Check for EEPROM Auto Read bit done.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ *
+ ******************************************************************************/
+static int32_t
+e1000_get_auto_rd_done(struct e1000_hw *hw)
+{
+ int32_t timeout = AUTO_READ_DONE_TIMEOUT;
+
+ DEBUGFUNC("e1000_get_auto_rd_done");
+
+ switch (hw->mac_type) {
+ default:
+ msec_delay(5);
+ break;
+ case e1000_82571:
+ case e1000_82572:
+ case e1000_82573:
+ case e1000_80003es2lan:
+ while(timeout) {
+ if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD) break;
+ else msec_delay(1);
+ timeout--;
}
+
+ if(!timeout) {
+ DEBUGOUT("Auto read by HW from EEPROM has not completed.\n");
+ return -E1000_ERR_RESET;
+ }
+ break;
}
+
+ /* PHY configuration from NVM just starts after EECD_AUTO_RD sets to high.
+ * Need to wait for PHY configuration completion before accessing NVM
+ * and PHY. */
+ if (hw->mac_type == e1000_82573)
+ msec_delay(25);
+
return E1000_SUCCESS;
}
-/*****************************************************************************
- * Set PHY to class A mode
- * Assumes the following operations will follow to enable the new class mode.
- * 1. Do a PHY soft reset
- * 2. Restart auto-negotiation or force link.
+/***************************************************************************
+ * Checks if the PHY configuration is done
*
- * hw - Struct containing variables accessed by shared code
- ****************************************************************************/
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ *
+ ***************************************************************************/
static int32_t
-e1000_set_phy_mode(struct e1000_hw *hw)
+e1000_get_phy_cfg_done(struct e1000_hw *hw)
{
- int32_t ret_val;
- uint16_t eeprom_data;
+ int32_t timeout = PHY_CFG_TIMEOUT;
+ uint32_t cfg_mask = E1000_EEPROM_CFG_DONE;
- DEBUGFUNC("e1000_set_phy_mode");
+ DEBUGFUNC("e1000_get_phy_cfg_done");
- if((hw->mac_type == e1000_82545_rev_3) &&
- (hw->media_type == e1000_media_type_copper)) {
- ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1, &eeprom_data);
- if(ret_val) {
- return ret_val;
+ switch (hw->mac_type) {
+ default:
+ msec_delay(10);
+ break;
+ case e1000_80003es2lan:
+ /* Separate *_CFG_DONE_* bit for each port */
+ if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)
+ cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1;
+ /* Fall Through */
+ case e1000_82571:
+ case e1000_82572:
+ while (timeout) {
+ if (E1000_READ_REG(hw, EEMNGCTL) & cfg_mask)
+ break;
+ else
+ msec_delay(1);
+ timeout--;
}
- if((eeprom_data != EEPROM_RESERVED_WORD) &&
- (eeprom_data & EEPROM_PHY_CLASS_A)) {
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x000B);
- if(ret_val)
- return ret_val;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x8104);
- if(ret_val)
- return ret_val;
-
- hw->phy_reset_disable = FALSE;
+ if (!timeout) {
+ DEBUGOUT("MNG configuration cycle has not completed.\n");
+ return -E1000_ERR_RESET;
}
+ break;
}
return E1000_SUCCESS;
}
-/*****************************************************************************
+/***************************************************************************
+ *
+ * Using the combination of SMBI and SWESMBI semaphore bits when resetting
+ * adapter or Eeprom access.
*
- * This function sets the lplu state according to the active flag. When
- * activating lplu this function also disables smart speed and vise versa.
- * lplu will not be activated unless the device autonegotiation advertisment
- * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
* hw: Struct containing variables accessed by shared code
- * active - true to enable lplu false to disable lplu.
*
- * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * returns: - E1000_ERR_EEPROM if fail to access EEPROM.
* E1000_SUCCESS at any other case.
*
- ****************************************************************************/
-
-int32_t
-e1000_set_d3_lplu_state(struct e1000_hw *hw,
- boolean_t active)
+ ***************************************************************************/
+static int32_t
+e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
{
- int32_t ret_val;
- uint16_t phy_data;
- DEBUGFUNC("e1000_set_d3_lplu_state");
+ int32_t timeout;
+ uint32_t swsm;
+
+ DEBUGFUNC("e1000_get_hw_eeprom_semaphore");
- if(!((hw->mac_type == e1000_82541_rev_2) ||
- (hw->mac_type == e1000_82547_rev_2)))
+ if(!hw->eeprom_semaphore_present)
return E1000_SUCCESS;
- /* During driver activity LPLU should not be used or it will attain link
- * from the lowest speeds starting from 10Mbps. The capability is used for
- * Dx transitions and states */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data);
- if(ret_val)
- return ret_val;
+ if (hw->mac_type == e1000_80003es2lan) {
+ /* Get the SW semaphore. */
+ if (e1000_get_software_semaphore(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+ }
- if(!active) {
- phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
- if(ret_val)
- return ret_val;
+ /* Get the FW semaphore. */
+ timeout = hw->eeprom.word_size + 1;
+ while(timeout) {
+ swsm = E1000_READ_REG(hw, SWSM);
+ swsm |= E1000_SWSM_SWESMBI;
+ E1000_WRITE_REG(hw, SWSM, swsm);
+ /* if we managed to set the bit we got the semaphore. */
+ swsm = E1000_READ_REG(hw, SWSM);
+ if(swsm & E1000_SWSM_SWESMBI)
+ break;
- /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
- * Dx states where the power conservation is most important. During
- * driver activity we should enable SmartSpeed, so performance is
- * maintained. */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
- if(ret_val)
- return ret_val;
+ udelay(50);
+ timeout--;
+ }
- phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data);
- if(ret_val)
- return ret_val;
+ if(!timeout) {
+ /* Release semaphores */
+ e1000_put_hw_eeprom_semaphore(hw);
+ DEBUGOUT("Driver can't access the Eeprom - SWESMBI bit is set.\n");
+ return -E1000_ERR_EEPROM;
+ }
- } else if((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) ||
- (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL ) ||
- (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) {
+ return E1000_SUCCESS;
+}
- phy_data |= IGP01E1000_GMII_FLEX_SPD;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
- if(ret_val)
- return ret_val;
+/***************************************************************************
+ * This function clears HW semaphore bits.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - None.
+ *
+ ***************************************************************************/
+static void
+e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw)
+{
+ uint32_t swsm;
- /* When LPLU is enabled we should disable SmartSpeed */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
- if(ret_val)
- return ret_val;
+ DEBUGFUNC("e1000_put_hw_eeprom_semaphore");
- phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data);
- if(ret_val)
- return ret_val;
+ if(!hw->eeprom_semaphore_present)
+ return;
- }
- return E1000_SUCCESS;
+ swsm = E1000_READ_REG(hw, SWSM);
+ if (hw->mac_type == e1000_80003es2lan) {
+ /* Release both semaphores. */
+ swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
+ } else
+ swsm &= ~(E1000_SWSM_SWESMBI);
+ E1000_WRITE_REG(hw, SWSM, swsm);
}
-/******************************************************************************
- * Change VCO speed register to improve Bit Error Rate performance of SERDES.
+/***************************************************************************
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-static int32_t
-e1000_set_vco_speed(struct e1000_hw *hw)
+ * Obtaining software semaphore bit (SMBI) before resetting PHY.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_RESET if fail to obtain semaphore.
+ * E1000_SUCCESS at any other case.
+ *
+ ***************************************************************************/
+int32_t
+e1000_get_software_semaphore(struct e1000_hw *hw)
{
- int32_t ret_val;
- uint16_t default_page = 0;
- uint16_t phy_data;
+ int32_t timeout = hw->eeprom.word_size + 1;
+ uint32_t swsm;
- DEBUGFUNC("e1000_set_vco_speed");
+ DEBUGFUNC("e1000_get_software_semaphore");
- switch(hw->mac_type) {
- case e1000_82545_rev_3:
- case e1000_82546_rev_3:
- break;
- default:
+ if (hw->mac_type != e1000_80003es2lan)
return E1000_SUCCESS;
- }
- /* Set PHY register 30, page 5, bit 8 to 0 */
+ while(timeout) {
+ swsm = E1000_READ_REG(hw, SWSM);
+ /* If SMBI bit cleared, it is now set and we hold the semaphore */
+ if(!(swsm & E1000_SWSM_SMBI))
+ break;
+ msec_delay_irq(1);
+ timeout--;
+ }
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page);
- if(ret_val)
- return ret_val;
+ if(!timeout) {
+ DEBUGOUT("Driver can't access device - SMBI bit is set.\n");
+ return -E1000_ERR_RESET;
+ }
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005);
- if(ret_val)
- return ret_val;
+ return E1000_SUCCESS;
+}
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
- if(ret_val)
- return ret_val;
+/***************************************************************************
+ *
+ * Release semaphore bit (SMBI).
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ ***************************************************************************/
+void
+e1000_release_software_semaphore(struct e1000_hw *hw)
+{
+ uint32_t swsm;
- phy_data &= ~M88E1000_PHY_VCO_REG_BIT8;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
- if(ret_val)
- return ret_val;
+ DEBUGFUNC("e1000_release_software_semaphore");
- /* Set PHY register 30, page 4, bit 11 to 1 */
+ if (hw->mac_type != e1000_80003es2lan)
+ return;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004);
- if(ret_val)
- return ret_val;
+ swsm = E1000_READ_REG(hw, SWSM);
+ /* Release the SW semaphores.*/
+ swsm &= ~E1000_SWSM_SMBI;
+ E1000_WRITE_REG(hw, SWSM, swsm);
+}
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
- if(ret_val)
- return ret_val;
+/******************************************************************************
+ * Checks if PHY reset is blocked due to SOL/IDER session, for example.
+ * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to
+ * the caller to figure out how to deal with it.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_BLK_PHY_RESET
+ * E1000_SUCCESS
+ *
+ *****************************************************************************/
+int32_t
+e1000_check_phy_reset_block(struct e1000_hw *hw)
+{
+ uint32_t manc = 0;
- phy_data |= M88E1000_PHY_VCO_REG_BIT11;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
- if(ret_val)
- return ret_val;
+ if (hw->mac_type > e1000_82547_rev_2)
+ manc = E1000_READ_REG(hw, MANC);
+ return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ?
+ E1000_BLK_PHY_RESET : E1000_SUCCESS;
+}
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, default_page);
- if(ret_val)
- return ret_val;
+static uint8_t
+e1000_arc_subsystem_valid(struct e1000_hw *hw)
+{
+ uint32_t fwsm;
- return E1000_SUCCESS;
+ /* On 8257x silicon, registers in the range of 0x8800 - 0x8FFC
+ * may not be provided a DMA clock when no manageability features are
+ * enabled. We do not want to perform any reads/writes to these registers
+ * if this is the case. We read FWSM to determine the manageability mode.
+ */
+ switch (hw->mac_type) {
+ case e1000_82571:
+ case e1000_82572:
+ case e1000_82573:
+ case e1000_80003es2lan:
+ fwsm = E1000_READ_REG(hw, FWSM);
+ if((fwsm & E1000_FWSM_MODE_MASK) != 0)
+ return TRUE;
+ break;
+ default:
+ break;
+ }
+ return FALSE;
}
+
+
git://git.onelab.eu / linux-2.6.git / blobdiff