static int32_t e1000_set_phy_mode(struct e1000_hw *hw);
static int32_t e1000_host_if_read_cookie(struct e1000_hw *hw, uint8_t *buffer);
static uint8_t e1000_calculate_mng_checksum(char *buffer, uint32_t length);
+static uint8_t e1000_arc_subsystem_valid(struct e1000_hw *hw);
+static int32_t e1000_check_downshift(struct e1000_hw *hw);
+static int32_t e1000_check_polarity(struct e1000_hw *hw, uint16_t *polarity);
+static void e1000_clear_hw_cntrs(struct e1000_hw *hw);
+static void e1000_clear_vfta(struct e1000_hw *hw);
+static int32_t e1000_commit_shadow_ram(struct e1000_hw *hw);
+static int32_t e1000_config_dsp_after_link_change(struct e1000_hw *hw,
+ boolean_t link_up);
+static int32_t e1000_config_fc_after_link_up(struct e1000_hw *hw);
+static int32_t e1000_detect_gig_phy(struct e1000_hw *hw);
+static int32_t e1000_get_auto_rd_done(struct e1000_hw *hw);
+static int32_t e1000_get_cable_length(struct e1000_hw *hw,
+ uint16_t *min_length,
+ uint16_t *max_length);
+static int32_t e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw);
+static int32_t e1000_get_phy_cfg_done(struct e1000_hw *hw);
+static int32_t e1000_id_led_init(struct e1000_hw * hw);
+static void e1000_init_rx_addrs(struct e1000_hw *hw);
+static boolean_t e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw);
+static int32_t e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd);
+static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw);
+static int32_t e1000_read_eeprom_eerd(struct e1000_hw *hw, uint16_t offset,
+ uint16_t words, uint16_t *data);
+static int32_t e1000_set_d0_lplu_state(struct e1000_hw *hw, boolean_t active);
+static int32_t e1000_set_d3_lplu_state(struct e1000_hw *hw, boolean_t active);
+static int32_t e1000_wait_autoneg(struct e1000_hw *hw);
+
+static void e1000_write_reg_io(struct e1000_hw *hw, uint32_t offset,
+ uint32_t value);
+
+#define E1000_WRITE_REG_IO(a, reg, val) \
+ e1000_write_reg_io((a), E1000_##reg, val)
/* IGP cable length table */
static const
static const
uint16_t e1000_igp_2_cable_length_table[IGP02E1000_AGC_LENGTH_TABLE_SIZE] =
- { 8, 13, 17, 19, 21, 23, 25, 27, 29, 31, 33, 35, 37, 39, 41, 43,
- 22, 24, 27, 30, 32, 35, 37, 40, 42, 44, 47, 49, 51, 54, 56, 58,
- 32, 35, 38, 41, 44, 47, 50, 53, 55, 58, 61, 63, 66, 69, 71, 74,
- 43, 47, 51, 54, 58, 61, 64, 67, 71, 74, 77, 80, 82, 85, 88, 90,
- 57, 62, 66, 70, 74, 77, 81, 85, 88, 91, 94, 97, 100, 103, 106, 108,
- 73, 78, 82, 87, 91, 95, 98, 102, 105, 109, 112, 114, 117, 119, 122, 124,
- 91, 96, 101, 105, 109, 113, 116, 119, 122, 125, 127, 128, 128, 128, 128, 128,
- 108, 113, 117, 121, 124, 127, 128, 128, 128, 128, 128, 128, 128, 128, 128, 128};
+ { 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21,
+ 0, 0, 0, 3, 6, 10, 13, 16, 19, 23, 26, 29, 32, 35, 38, 41,
+ 6, 10, 14, 18, 22, 26, 30, 33, 37, 41, 44, 48, 51, 54, 58, 61,
+ 21, 26, 31, 35, 40, 44, 49, 53, 57, 61, 65, 68, 72, 75, 79, 82,
+ 40, 45, 51, 56, 61, 66, 70, 75, 79, 83, 87, 91, 94, 98, 101, 104,
+ 60, 66, 72, 77, 82, 87, 92, 96, 100, 104, 108, 111, 114, 117, 119, 121,
+ 83, 89, 95, 100, 105, 109, 113, 116, 119, 122, 124,
+ 104, 109, 114, 118, 121, 124};
/******************************************************************************
case E1000_DEV_ID_82546GB_SERDES:
case E1000_DEV_ID_82546GB_PCIE:
case E1000_DEV_ID_82546GB_QUAD_COPPER:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
hw->mac_type = e1000_82546_rev_3;
break;
case E1000_DEV_ID_82541EI:
case E1000_DEV_ID_82547GI:
hw->mac_type = e1000_82547_rev_2;
break;
+ case E1000_DEV_ID_82571EB_COPPER:
+ case E1000_DEV_ID_82571EB_FIBER:
+ case E1000_DEV_ID_82571EB_SERDES:
+ hw->mac_type = e1000_82571;
+ break;
+ case E1000_DEV_ID_82572EI_COPPER:
+ case E1000_DEV_ID_82572EI_FIBER:
+ case E1000_DEV_ID_82572EI_SERDES:
+ hw->mac_type = e1000_82572;
+ break;
case E1000_DEV_ID_82573E:
case E1000_DEV_ID_82573E_IAMT:
+ case E1000_DEV_ID_82573L:
hw->mac_type = e1000_82573;
break;
default:
}
switch(hw->mac_type) {
+ case e1000_82571:
+ case e1000_82572:
case e1000_82573:
hw->eeprom_semaphore_present = TRUE;
/* fall through */
switch (hw->device_id) {
case E1000_DEV_ID_82545GM_SERDES:
case E1000_DEV_ID_82546GB_SERDES:
+ case E1000_DEV_ID_82571EB_SERDES:
+ case E1000_DEV_ID_82572EI_SERDES:
hw->media_type = e1000_media_type_internal_serdes;
break;
default:
- if(hw->mac_type >= e1000_82543) {
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ hw->media_type = e1000_media_type_fiber;
+ break;
+ case e1000_82573:
+ /* The STATUS_TBIMODE bit is reserved or reused for the this
+ * device.
+ */
+ hw->media_type = e1000_media_type_copper;
+ break;
+ default:
status = E1000_READ_REG(hw, STATUS);
- if(status & E1000_STATUS_TBIMODE) {
+ if (status & E1000_STATUS_TBIMODE) {
hw->media_type = e1000_media_type_fiber;
/* tbi_compatibility not valid on fiber */
hw->tbi_compatibility_en = FALSE;
} else {
hw->media_type = e1000_media_type_copper;
}
- } else {
- /* This is an 82542 (fiber only) */
- hw->media_type = e1000_media_type_fiber;
+ break;
}
}
}
msec_delay(20);
break;
case e1000_82573:
- udelay(10);
- ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
- ctrl_ext |= E1000_CTRL_EXT_EE_RST;
- E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
- E1000_WRITE_FLUSH(hw);
+ if (e1000_is_onboard_nvm_eeprom(hw) == FALSE) {
+ udelay(10);
+ ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+ E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH(hw);
+ }
/* fall through */
+ case e1000_82571:
+ case e1000_82572:
ret_val = e1000_get_auto_rd_done(hw);
if(ret_val)
/* We don't want to continue accessing MAC registers. */
uint16_t cmd_mmrbc;
uint16_t stat_mmrbc;
uint32_t mta_size;
+ uint32_t ctrl_ext;
DEBUGFUNC("e1000_init_hw");
switch (hw->mac_type) {
default:
break;
+ case e1000_82571:
+ case e1000_82572:
case e1000_82573:
ctrl |= E1000_TXDCTL_COUNT_DESC;
break;
e1000_enable_tx_pkt_filtering(hw);
}
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_82571:
+ case e1000_82572:
+ ctrl = E1000_READ_REG(hw, TXDCTL1);
+ ctrl &= ~E1000_TXDCTL_WTHRESH;
+ ctrl |= E1000_TXDCTL_COUNT_DESC | E1000_TXDCTL_FULL_TX_DESC_WB;
+ ctrl |= (1 << 22);
+ E1000_WRITE_REG(hw, TXDCTL1, ctrl);
+ break;
+ }
+
+
+
+ if (hw->mac_type == e1000_82573) {
+ uint32_t gcr = E1000_READ_REG(hw, GCR);
+ gcr |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
+ E1000_WRITE_REG(hw, GCR, gcr);
+ }
/* Clear all of the statistics registers (clear on read). It is
* important that we do this after we have tried to establish link
*/
e1000_clear_hw_cntrs(hw);
+ if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
+ hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
+ ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ /* Relaxed ordering must be disabled to avoid a parity
+ * error crash in a PCI slot. */
+ ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
+ E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+ }
+
return ret_val;
}
DEBUGFUNC("e1000_setup_link");
+ /* In the case of the phy reset being blocked, we already have a link.
+ * We do not have to set it up again. */
+ if (e1000_check_phy_reset_block(hw))
+ return E1000_SUCCESS;
+
/* Read and store word 0x0F of the EEPROM. This word contains bits
* that determine the hardware's default PAUSE (flow control) mode,
* a bit that determines whether the HW defaults to enabling or
* control setting, then the variable hw->fc will
* be initialized based on a value in the EEPROM.
*/
- if(e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data)) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
-
- if(hw->fc == e1000_fc_default) {
- if((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
- hw->fc = e1000_fc_none;
- else if((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
- EEPROM_WORD0F_ASM_DIR)
- hw->fc = e1000_fc_tx_pause;
- else
+ if (hw->fc == e1000_fc_default) {
+ switch (hw->mac_type) {
+ case e1000_82573:
hw->fc = e1000_fc_full;
+ break;
+ default:
+ ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+ 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
+ hw->fc = e1000_fc_none;
+ else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
+ EEPROM_WORD0F_ASM_DIR)
+ hw->fc = e1000_fc_tx_pause;
+ else
+ hw->fc = e1000_fc_full;
+ break;
+ }
}
/* We want to save off the original Flow Control configuration just
DEBUGFUNC("e1000_setup_fiber_serdes_link");
+ /* On 82571 and 82572 Fiber connections, SerDes loopback mode persists
+ * until explicitly turned off or a power cycle is performed. A read to
+ * the register does not indicate its status. Therefore, we ensure
+ * loopback mode is disabled during initialization.
+ */
+ if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572)
+ E1000_WRITE_REG(hw, SCTL, E1000_DISABLE_SERDES_LOOPBACK);
+
/* On adapters with a MAC newer than 82544, SW Defineable pin 1 will be
* set when the optics detect a signal. On older adapters, it will be
* cleared when there is a signal. This applies to fiber media only.
ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
if(ret_val)
return ret_val;
- }
+ }
- return E1000_SUCCESS;
+ return E1000_SUCCESS;
}
if(ret_val)
return ret_val;
- /* Read the MII 1000Base-T Control Register (Address 9). */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
- if(ret_val)
- return ret_val;
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+ if(ret_val)
+ return ret_val;
/* Need to parse both autoneg_advertised and fc and set up
* the appropriate PHY registers. First we will parse for
void
e1000_config_collision_dist(struct e1000_hw *hw)
{
- uint32_t tctl;
+ uint32_t tctl, coll_dist;
DEBUGFUNC("e1000_config_collision_dist");
+ if (hw->mac_type < e1000_82543)
+ coll_dist = E1000_COLLISION_DISTANCE_82542;
+ else
+ coll_dist = E1000_COLLISION_DISTANCE;
+
tctl = E1000_READ_REG(hw, TCTL);
tctl &= ~E1000_TCTL_COLD;
- tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT;
+ tctl |= coll_dist << E1000_COLD_SHIFT;
E1000_WRITE_REG(hw, TCTL, tctl);
E1000_WRITE_FLUSH(hw);
* based on the flow control negotiated by the PHY. In TBI mode, the TFCE
* and RFCE bits will be automaticaly set to the negotiated flow control mode.
*****************************************************************************/
-int32_t
+static int32_t
e1000_config_fc_after_link_up(struct e1000_hw *hw)
{
int32_t ret_val;
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
-int32_t
+static int32_t
e1000_wait_autoneg(struct e1000_hw *hw)
{
int32_t ret_val;
if(hw->mac_type > e1000_82543) {
/* Read the device control register and assert the E1000_CTRL_PHY_RST
* bit. Then, take it out of reset.
+ * For pre-e1000_82571 hardware, we delay for 10ms between the assert
+ * and deassert. For e1000_82571 hardware and later, we instead delay
+ * for 10ms after the deassertion.
*/
ctrl = E1000_READ_REG(hw, CTRL);
E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST);
E1000_WRITE_FLUSH(hw);
- msec_delay(10);
+
+ if (hw->mac_type < e1000_82571)
+ msec_delay(10);
+ else
+ udelay(100);
+
E1000_WRITE_REG(hw, CTRL, ctrl);
E1000_WRITE_FLUSH(hw);
+
+ if (hw->mac_type >= e1000_82571)
+ msec_delay(10);
} else {
/* Read the Extended Device Control Register, assert the PHY_RESET_DIR
* bit to put the PHY into reset. Then, take it out of reset.
switch (hw->mac_type) {
case e1000_82541_rev_2:
+ case e1000_82571:
+ case e1000_82572:
ret_val = e1000_phy_hw_reset(hw);
if(ret_val)
return ret_val;
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
-int32_t
+static int32_t
e1000_detect_gig_phy(struct e1000_hw *hw)
{
int32_t phy_init_status, ret_val;
DEBUGFUNC("e1000_detect_gig_phy");
+ /* The 82571 firmware may still be configuring the PHY. In this
+ * case, we cannot access the PHY until the configuration is done. So
+ * we explicitly set the PHY values. */
+ if(hw->mac_type == e1000_82571 ||
+ hw->mac_type == e1000_82572) {
+ hw->phy_id = IGP01E1000_I_PHY_ID;
+ hw->phy_type = e1000_phy_igp_2;
+ return E1000_SUCCESS;
+ }
+
/* Read the PHY ID Registers to identify which PHY is onboard. */
ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
if(ret_val)
* hw - Struct containing variables accessed by shared code
* phy_info - PHY information structure
******************************************************************************/
-int32_t
+static int32_t
e1000_phy_igp_get_info(struct e1000_hw *hw,
struct e1000_phy_info *phy_info)
{
* hw - Struct containing variables accessed by shared code
* phy_info - PHY information structure
******************************************************************************/
-int32_t
+static int32_t
e1000_phy_m88_get_info(struct e1000_hw *hw,
struct e1000_phy_info *phy_info)
{
eeprom->use_eerd = FALSE;
eeprom->use_eewr = FALSE;
break;
+ case e1000_82571:
+ case e1000_82572:
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ break;
case e1000_82573:
eeprom->type = e1000_eeprom_spi;
eeprom->opcode_bits = 8;
eecd = E1000_READ_REG(hw, EECD);
if (hw->mac_type != e1000_82573) {
- /* Request EEPROM Access */
- if(hw->mac_type > e1000_82544) {
- eecd |= E1000_EECD_REQ;
- E1000_WRITE_REG(hw, EECD, eecd);
- eecd = E1000_READ_REG(hw, EECD);
- while((!(eecd & E1000_EECD_GNT)) &&
- (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
- i++;
- udelay(5);
- eecd = E1000_READ_REG(hw, EECD);
- }
- if(!(eecd & E1000_EECD_GNT)) {
- eecd &= ~E1000_EECD_REQ;
+ /* Request EEPROM Access */
+ if(hw->mac_type > e1000_82544) {
+ eecd |= E1000_EECD_REQ;
E1000_WRITE_REG(hw, EECD, eecd);
- DEBUGOUT("Could not acquire EEPROM grant\n");
- return -E1000_ERR_EEPROM;
+ eecd = E1000_READ_REG(hw, EECD);
+ while((!(eecd & E1000_EECD_GNT)) &&
+ (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
+ i++;
+ udelay(5);
+ eecd = E1000_READ_REG(hw, EECD);
+ }
+ if(!(eecd & E1000_EECD_GNT)) {
+ eecd &= ~E1000_EECD_REQ;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ DEBUGOUT("Could not acquire EEPROM grant\n");
+ e1000_put_hw_eeprom_semaphore(hw);
+ return -E1000_ERR_EEPROM;
+ }
}
}
- }
/* Setup EEPROM for Read/Write */
return -E1000_ERR_EEPROM;
}
- /* FLASH reads without acquiring the semaphore are safe in 82573-based
- * controllers.
- */
- if ((e1000_is_onboard_nvm_eeprom(hw) == TRUE) ||
- (hw->mac_type != e1000_82573)) {
- /* Prepare the EEPROM for reading */
- if(e1000_acquire_eeprom(hw) != E1000_SUCCESS)
- return -E1000_ERR_EEPROM;
+ /* FLASH reads without acquiring the semaphore are safe */
+ if (e1000_is_onboard_nvm_eeprom(hw) == TRUE &&
+ hw->eeprom.use_eerd == FALSE) {
+ switch (hw->mac_type) {
+ default:
+ /* Prepare the EEPROM for reading */
+ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+ break;
+ }
}
- if(eeprom->use_eerd == TRUE) {
+ if (eeprom->use_eerd == TRUE) {
ret_val = e1000_read_eeprom_eerd(hw, offset, words, data);
if ((e1000_is_onboard_nvm_eeprom(hw) == TRUE) ||
(hw->mac_type != e1000_82573))
* data - word read from the EEPROM
* words - number of words to read
*****************************************************************************/
-int32_t
+static int32_t
e1000_read_eeprom_eerd(struct e1000_hw *hw,
uint16_t offset,
uint16_t words,
* data - word read from the EEPROM
* words - number of words to read
*****************************************************************************/
-int32_t
+static int32_t
e1000_write_eeprom_eewr(struct e1000_hw *hw,
uint16_t offset,
uint16_t words,
*
* hw - Struct containing variables accessed by shared code
*****************************************************************************/
-int32_t
+static int32_t
e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd)
{
uint32_t attempts = 100000;
*
* hw - Struct containing variables accessed by shared code
****************************************************************************/
-boolean_t
+static boolean_t
e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw)
{
uint32_t eecd = 0;
return -E1000_ERR_EEPROM;
}
- /* 82573 reads only through eerd */
+ /* 82573 writes only through eewr */
if(eeprom->use_eewr == TRUE)
return e1000_write_eeprom_eewr(hw, offset, words, data);
* data - word read from the EEPROM
* words - number of words to read
*****************************************************************************/
-int32_t
+static int32_t
e1000_commit_shadow_ram(struct e1000_hw *hw)
{
uint32_t attempts = 100000;
return -E1000_ERR_EEPROM;
}
- /* If STM opcode located in bits 15:8 of flop, reset firmware */
+ /* If STM opcode located in bits 15:8 of flop, reset firmware */
if ((flop & 0xFF00) == E1000_STM_OPCODE) {
E1000_WRITE_REG(hw, HICR, E1000_HICR_FW_RESET);
}
/* Perform the flash update */
E1000_WRITE_REG(hw, EECD, eecd | E1000_EECD_FLUPD);
- for (i=0; i < attempts; i++) {
+ for (i=0; i < attempts; i++) {
eecd = E1000_READ_REG(hw, EECD);
if ((eecd & E1000_EECD_FLUPD) == 0) {
break;
hw->perm_mac_addr[i] = (uint8_t) (eeprom_data & 0x00FF);
hw->perm_mac_addr[i+1] = (uint8_t) (eeprom_data >> 8);
}
- if(((hw->mac_type == e1000_82546) || (hw->mac_type == e1000_82546_rev_3)) &&
- (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1))
+
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ case e1000_82571:
+ if(E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)
hw->perm_mac_addr[5] ^= 0x01;
+ break;
+ }
for(i = 0; i < NODE_ADDRESS_SIZE; i++)
hw->mac_addr[i] = hw->perm_mac_addr[i];
* of the receive addresss registers. Clears the multicast table. Assumes
* the receiver is in reset when the routine is called.
*****************************************************************************/
-void
+static void
e1000_init_rx_addrs(struct e1000_hw *hw)
{
uint32_t i;
e1000_rar_set(hw, hw->mac_addr, 0);
rar_num = E1000_RAR_ENTRIES;
+
+ /* Reserve a spot for the Locally Administered Address to work around
+ * an 82571 issue in which a reset on one port will reload the MAC on
+ * the other port. */
+ if ((hw->mac_type == e1000_82571) && (hw->laa_is_present == TRUE))
+ rar_num -= 1;
/* Zero out the other 15 receive addresses. */
DEBUGOUT("Clearing RAR[1-15]\n");
for(i = 1; i < rar_num; i++) {
}
}
+#if 0
/******************************************************************************
* Updates the MAC's list of multicast addresses.
*
/* Clear RAR[1-15] */
DEBUGOUT(" Clearing RAR[1-15]\n");
num_rar_entry = E1000_RAR_ENTRIES;
+ /* Reserve a spot for the Locally Administered Address to work around
+ * an 82571 issue in which a reset on one port will reload the MAC on
+ * the other port. */
+ if ((hw->mac_type == e1000_82571) && (hw->laa_is_present == TRUE))
+ num_rar_entry -= 1;
+
for(i = rar_used_count; i < num_rar_entry; i++) {
E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
}
DEBUGOUT("MC Update Complete\n");
}
+#endif /* 0 */
/******************************************************************************
* Hashes an address to determine its location in the multicast table
*
* hw - Struct containing variables accessed by shared code
*****************************************************************************/
-void
+static void
e1000_clear_vfta(struct e1000_hw *hw)
{
uint32_t offset;
}
}
-int32_t
+static int32_t
e1000_id_led_init(struct e1000_hw * hw)
{
uint32_t ledctl;
*
* hw - Struct containing variables accessed by shared code
*****************************************************************************/
-void
+static void
e1000_clear_hw_cntrs(struct e1000_hw *hw)
{
volatile uint32_t temp;
temp = E1000_READ_REG(hw, ICTXQEC);
temp = E1000_READ_REG(hw, ICTXQMTC);
temp = E1000_READ_REG(hw, ICRXDMTC);
-
}
/******************************************************************************
hw->bus_speed = e1000_bus_speed_unknown;
hw->bus_width = e1000_bus_width_unknown;
break;
+ case e1000_82572:
case e1000_82573:
+ hw->bus_type = e1000_bus_type_pci_express;
+ hw->bus_speed = e1000_bus_speed_2500;
+ hw->bus_width = e1000_bus_width_pciex_1;
+ break;
+ case e1000_82571:
hw->bus_type = e1000_bus_type_pci_express;
hw->bus_speed = e1000_bus_speed_2500;
hw->bus_width = e1000_bus_width_pciex_4;
break;
}
}
+
+#if 0
/******************************************************************************
* Reads a value from one of the devices registers using port I/O (as opposed
* memory mapped I/O). Only 82544 and newer devices support port I/O.
e1000_io_write(hw, io_addr, offset);
return e1000_io_read(hw, io_data);
}
+#endif /* 0 */
/******************************************************************************
* Writes a value to one of the devices registers using port I/O (as opposed to
* offset - offset to write to
* value - value to write
*****************************************************************************/
-void
+static void
e1000_write_reg_io(struct e1000_hw *hw,
uint32_t offset,
uint32_t value)
* register to the minimum and maximum range.
* For IGP phy's, the function calculates the range by the AGC registers.
*****************************************************************************/
-int32_t
+static int32_t
e1000_get_cable_length(struct e1000_hw *hw,
uint16_t *min_length,
uint16_t *max_length)
int32_t ret_val;
uint16_t agc_value = 0;
uint16_t cur_agc, min_agc = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
+ uint16_t max_agc = 0;
uint16_t i, phy_data;
uint16_t cable_length;
IGP01E1000_AGC_RANGE) : 0;
*max_length = e1000_igp_cable_length_table[agc_value] +
IGP01E1000_AGC_RANGE;
+ } else if (hw->phy_type == e1000_phy_igp_2) {
+ uint16_t agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] =
+ {IGP02E1000_PHY_AGC_A,
+ IGP02E1000_PHY_AGC_B,
+ IGP02E1000_PHY_AGC_C,
+ IGP02E1000_PHY_AGC_D};
+ /* Read the AGC registers for all channels */
+ for (i = 0; i < IGP02E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Getting bits 15:9, which represent the combination of course and
+ * fine gain values. The result is a number that can be put into
+ * the lookup table to obtain the approximate cable length. */
+ cur_agc = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
+ IGP02E1000_AGC_LENGTH_MASK;
+
+ /* Remove min & max AGC values from calculation. */
+ if (e1000_igp_2_cable_length_table[min_agc] > e1000_igp_2_cable_length_table[cur_agc])
+ min_agc = cur_agc;
+ if (e1000_igp_2_cable_length_table[max_agc] < e1000_igp_2_cable_length_table[cur_agc])
+ max_agc = cur_agc;
+
+ agc_value += e1000_igp_2_cable_length_table[cur_agc];
+ }
+
+ agc_value -= (e1000_igp_2_cable_length_table[min_agc] + e1000_igp_2_cable_length_table[max_agc]);
+ agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2);
+
+ /* Calculate cable length with the error range of +/- 10 meters. */
+ *min_length = ((agc_value - IGP02E1000_AGC_RANGE) > 0) ?
+ (agc_value - IGP02E1000_AGC_RANGE) : 0;
+ *max_length = agc_value + IGP02E1000_AGC_RANGE;
}
return E1000_SUCCESS;
* return 0. If the link speed is 1000 Mbps the polarity status is in the
* IGP01E1000_PHY_PCS_INIT_REG.
*****************************************************************************/
-int32_t
+static int32_t
e1000_check_polarity(struct e1000_hw *hw,
uint16_t *polarity)
{
* Link Health register. In IGP this bit is latched high, so the driver must
* read it immediately after link is established.
*****************************************************************************/
-int32_t
+static int32_t
e1000_check_downshift(struct e1000_hw *hw)
{
int32_t ret_val;
*
****************************************************************************/
-int32_t
+static int32_t
e1000_config_dsp_after_link_change(struct e1000_hw *hw,
boolean_t link_up)
{
*
****************************************************************************/
-int32_t
+static int32_t
e1000_set_d3_lplu_state(struct e1000_hw *hw,
boolean_t active)
{
*
****************************************************************************/
-int32_t
+static int32_t
e1000_set_d0_lplu_state(struct e1000_hw *hw,
boolean_t active)
{
* timeout
* - E1000_SUCCESS for success.
****************************************************************************/
-int32_t
+static int32_t
e1000_mng_enable_host_if(struct e1000_hw * hw)
{
uint32_t hicr;
*
* returns - E1000_SUCCESS for success.
****************************************************************************/
-int32_t
+static int32_t
e1000_mng_host_if_write(struct e1000_hw * hw, uint8_t *buffer,
uint16_t length, uint16_t offset, uint8_t *sum)
{
*
* returns - E1000_SUCCESS for success.
****************************************************************************/
-int32_t
+static int32_t
e1000_mng_write_cmd_header(struct e1000_hw * hw,
struct e1000_host_mng_command_header * hdr)
{
*
* returns - E1000_SUCCESS for success.
****************************************************************************/
-int32_t
+static int32_t
e1000_mng_write_commit(
struct e1000_hw * hw)
{
* returns: - none.
*
***************************************************************************/
-void
+static void
e1000_set_pci_express_master_disable(struct e1000_hw *hw)
{
uint32_t ctrl;
E1000_WRITE_REG(hw, CTRL, ctrl);
}
+#if 0
/***************************************************************************
*
* Enables PCI-Express master access.
ctrl &= ~E1000_CTRL_GIO_MASTER_DISABLE;
E1000_WRITE_REG(hw, CTRL, ctrl);
}
+#endif /* 0 */
/*******************************************************************************
*
* E1000_SUCCESS at any other case.
*
******************************************************************************/
-int32_t
+static int32_t
e1000_get_auto_rd_done(struct e1000_hw *hw)
{
int32_t timeout = AUTO_READ_DONE_TIMEOUT;
default:
msec_delay(5);
break;
+ case e1000_82571:
+ case e1000_82572:
case e1000_82573:
while(timeout) {
if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD) break;
break;
}
+ /* PHY configuration from NVM just starts after EECD_AUTO_RD sets to high.
+ * Need to wait for PHY configuration completion before accessing NVM
+ * and PHY. */
+ if (hw->mac_type == e1000_82573)
+ msec_delay(25);
+
return E1000_SUCCESS;
}
* E1000_SUCCESS at any other case.
*
***************************************************************************/
-int32_t
+static int32_t
e1000_get_phy_cfg_done(struct e1000_hw *hw)
{
+ int32_t timeout = PHY_CFG_TIMEOUT;
+ uint32_t cfg_mask = E1000_EEPROM_CFG_DONE;
+
DEBUGFUNC("e1000_get_phy_cfg_done");
- /* Simply wait for 10ms */
- msec_delay(10);
+ switch (hw->mac_type) {
+ default:
+ msec_delay(10);
+ break;
+ case e1000_82571:
+ case e1000_82572:
+ while (timeout) {
+ if (E1000_READ_REG(hw, EEMNGCTL) & cfg_mask)
+ break;
+ else
+ msec_delay(1);
+ timeout--;
+ }
+
+ if (!timeout) {
+ DEBUGOUT("MNG configuration cycle has not completed.\n");
+ return -E1000_ERR_RESET;
+ }
+ break;
+ }
+
+ /* PHY configuration from NVM just starts after EECD_AUTO_RD sets to high.
+ * Need to wait for PHY configuration completion before accessing NVM
+ * and PHY. */
+ if (hw->mac_type == e1000_82573)
+ msec_delay(25);
return E1000_SUCCESS;
}
* E1000_SUCCESS at any other case.
*
***************************************************************************/
-int32_t
+static int32_t
e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
{
int32_t timeout;
* returns: - None.
*
***************************************************************************/
-void
+static void
e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw)
{
uint32_t swsm;
return;
swsm = E1000_READ_REG(hw, SWSM);
- /* Release both semaphores. */
- swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
+ swsm &= ~(E1000_SWSM_SWESMBI);
E1000_WRITE_REG(hw, SWSM, swsm);
}
e1000_check_phy_reset_block(struct e1000_hw *hw)
{
uint32_t manc = 0;
- if(hw->mac_type > e1000_82547_rev_2)
+
+ if (hw->mac_type > e1000_82547_rev_2)
manc = E1000_READ_REG(hw, MANC);
return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ?
E1000_BLK_PHY_RESET : E1000_SUCCESS;
}
-uint8_t
+static uint8_t
e1000_arc_subsystem_valid(struct e1000_hw *hw)
{
uint32_t fwsm;
* if this is the case. We read FWSM to determine the manageability mode.
*/
switch (hw->mac_type) {
+ case e1000_82571:
+ case e1000_82572:
case e1000_82573:
fwsm = E1000_READ_REG(hw, FWSM);
if((fwsm & E1000_FWSM_MODE_MASK) != 0)
git://git.onelab.eu / linux-2.6.git / blobdiff