/*******************************************************************************
- Copyright(c) 1999 - 2004 Intel Corporation. All rights reserved.
+ Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
e1000_82541_rev_2,
e1000_82547,
e1000_82547_rev_2,
+ e1000_82571,
+ e1000_82572,
+ e1000_82573,
+ e1000_80003es2lan,
e1000_num_macs
} e1000_mac_type;
e1000_eeprom_uninitialized = 0,
e1000_eeprom_spi,
e1000_eeprom_microwire,
+ e1000_eeprom_flash,
+ e1000_eeprom_none, /* No NVM support */
e1000_num_eeprom_types
} e1000_eeprom_type;
e1000_bus_type_unknown = 0,
e1000_bus_type_pci,
e1000_bus_type_pcix,
+ e1000_bus_type_pci_express,
e1000_bus_type_reserved
} e1000_bus_type;
e1000_bus_speed_100,
e1000_bus_speed_120,
e1000_bus_speed_133,
+ e1000_bus_speed_2500,
e1000_bus_speed_reserved
} e1000_bus_speed;
e1000_bus_width_unknown = 0,
e1000_bus_width_32,
e1000_bus_width_64,
+ e1000_bus_width_pciex_1,
+ e1000_bus_width_pciex_2,
+ e1000_bus_width_pciex_4,
e1000_bus_width_reserved
} e1000_bus_width;
e1000_cable_length_undefined = 0xFF
} e1000_cable_length;
+typedef enum {
+ e1000_gg_cable_length_60 = 0,
+ e1000_gg_cable_length_60_115 = 1,
+ e1000_gg_cable_length_115_150 = 2,
+ e1000_gg_cable_length_150 = 4
+} e1000_gg_cable_length;
+
typedef enum {
e1000_igp_cable_length_10 = 10,
e1000_igp_cable_length_20 = 20,
e1000_igp_cable_length_90 = 90,
e1000_igp_cable_length_100 = 100,
e1000_igp_cable_length_110 = 110,
+ e1000_igp_cable_length_115 = 115,
e1000_igp_cable_length_120 = 120,
e1000_igp_cable_length_130 = 130,
e1000_igp_cable_length_140 = 140,
e1000_downshift_undefined = 0xFF
} e1000_downshift;
+typedef enum {
+ e1000_smart_speed_default = 0,
+ e1000_smart_speed_on,
+ e1000_smart_speed_off
+} e1000_smart_speed;
+
typedef enum {
e1000_polarity_reversal_enabled = 0,
e1000_polarity_reversal_disabled,
typedef enum {
e1000_phy_m88 = 0,
e1000_phy_igp,
+ e1000_phy_igp_2,
+ e1000_phy_gg82563,
e1000_phy_undefined = 0xFF
} e1000_phy_type;
uint16_t address_bits;
uint16_t delay_usec;
uint16_t page_size;
+ boolean_t use_eerd;
+ boolean_t use_eewr;
};
+/* Flex ASF Information */
+#define E1000_HOST_IF_MAX_SIZE 2048
+
+typedef enum {
+ e1000_byte_align = 0,
+ e1000_word_align = 1,
+ e1000_dword_align = 2
+} e1000_align_type;
+
/* Error Codes */
#define E1000_ERR_PARAM 4
#define E1000_ERR_MAC_TYPE 5
#define E1000_ERR_PHY_TYPE 6
+#define E1000_ERR_RESET 9
+#define E1000_ERR_MASTER_REQUESTS_PENDING 10
+#define E1000_ERR_HOST_INTERFACE_COMMAND 11
+#define E1000_BLK_PHY_RESET 12
+#define E1000_ERR_SWFW_SYNC 13
/* Function prototypes */
/* Initialization */
int32_t e1000_setup_link(struct e1000_hw *hw);
int32_t e1000_phy_setup_autoneg(struct e1000_hw *hw);
void e1000_config_collision_dist(struct e1000_hw *hw);
-int32_t e1000_config_fc_after_link_up(struct e1000_hw *hw);
int32_t e1000_check_for_link(struct e1000_hw *hw);
int32_t e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t * speed, uint16_t * duplex);
-int32_t e1000_wait_autoneg(struct e1000_hw *hw);
int32_t e1000_force_mac_fc(struct e1000_hw *hw);
/* PHY */
int32_t e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *phy_data);
int32_t e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data);
-void e1000_phy_hw_reset(struct e1000_hw *hw);
+int32_t e1000_phy_hw_reset(struct e1000_hw *hw);
int32_t e1000_phy_reset(struct e1000_hw *hw);
-int32_t e1000_detect_gig_phy(struct e1000_hw *hw);
int32_t e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info);
-int32_t e1000_phy_m88_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info);
-int32_t e1000_phy_igp_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info);
-int32_t e1000_get_cable_length(struct e1000_hw *hw, uint16_t *min_length, uint16_t *max_length);
-int32_t e1000_check_polarity(struct e1000_hw *hw, uint16_t *polarity);
-int32_t e1000_check_downshift(struct e1000_hw *hw);
int32_t e1000_validate_mdi_setting(struct e1000_hw *hw);
+int32_t e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data);
+int32_t e1000_write_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data);
/* EEPROM Functions */
-void e1000_init_eeprom_params(struct e1000_hw *hw);
+int32_t e1000_init_eeprom_params(struct e1000_hw *hw);
+
+/* MNG HOST IF functions */
+uint32_t e1000_enable_mng_pass_thru(struct e1000_hw *hw);
+
+#define E1000_MNG_DHCP_TX_PAYLOAD_CMD 64
+#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8 /* Host Interface data length */
+
+#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10 /* Time in ms to process MNG command */
+#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */
+#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */
+#define E1000_MNG_IAMT_MODE 0x3
+#define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */
+
+#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */
+#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT 0x2 /* DHCP parsing enabled */
+#define E1000_VFTA_ENTRY_SHIFT 0x5
+#define E1000_VFTA_ENTRY_MASK 0x7F
+#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F
+
+struct e1000_host_mng_command_header {
+ uint8_t command_id;
+ uint8_t checksum;
+ uint16_t reserved1;
+ uint16_t reserved2;
+ uint16_t command_length;
+};
+
+struct e1000_host_mng_command_info {
+ struct e1000_host_mng_command_header command_header; /* Command Head/Command Result Head has 4 bytes */
+ uint8_t command_data[E1000_HI_MAX_MNG_DATA_LENGTH]; /* Command data can length 0..0x658*/
+};
+#ifdef __BIG_ENDIAN
+struct e1000_host_mng_dhcp_cookie{
+ uint32_t signature;
+ uint16_t vlan_id;
+ uint8_t reserved0;
+ uint8_t status;
+ uint32_t reserved1;
+ uint8_t checksum;
+ uint8_t reserved3;
+ uint16_t reserved2;
+};
+#else
+struct e1000_host_mng_dhcp_cookie{
+ uint32_t signature;
+ uint8_t status;
+ uint8_t reserved0;
+ uint16_t vlan_id;
+ uint32_t reserved1;
+ uint16_t reserved2;
+ uint8_t reserved3;
+ uint8_t checksum;
+};
+#endif
+
+int32_t e1000_mng_write_dhcp_info(struct e1000_hw *hw, uint8_t *buffer,
+ uint16_t length);
+boolean_t e1000_check_mng_mode(struct e1000_hw *hw);
+boolean_t e1000_enable_tx_pkt_filtering(struct e1000_hw *hw);
+
int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t reg, uint16_t words, uint16_t *data);
int32_t e1000_validate_eeprom_checksum(struct e1000_hw *hw);
int32_t e1000_update_eeprom_checksum(struct e1000_hw *hw);
int32_t e1000_write_eeprom(struct e1000_hw *hw, uint16_t reg, uint16_t words, uint16_t *data);
int32_t e1000_read_part_num(struct e1000_hw *hw, uint32_t * part_num);
int32_t e1000_read_mac_addr(struct e1000_hw * hw);
+int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask);
+void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask);
/* Filters (multicast, vlan, receive) */
-void e1000_init_rx_addrs(struct e1000_hw *hw);
void e1000_mc_addr_list_update(struct e1000_hw *hw, uint8_t * mc_addr_list, uint32_t mc_addr_count, uint32_t pad, uint32_t rar_used_count);
uint32_t e1000_hash_mc_addr(struct e1000_hw *hw, uint8_t * mc_addr);
void e1000_mta_set(struct e1000_hw *hw, uint32_t hash_value);
void e1000_rar_set(struct e1000_hw *hw, uint8_t * mc_addr, uint32_t rar_index);
void e1000_write_vfta(struct e1000_hw *hw, uint32_t offset, uint32_t value);
-void e1000_clear_vfta(struct e1000_hw *hw);
/* LED functions */
int32_t e1000_setup_led(struct e1000_hw *hw);
/* Adaptive IFS Functions */
/* Everything else */
-uint32_t e1000_enable_mng_pass_thru(struct e1000_hw *hw);
-void e1000_clear_hw_cntrs(struct e1000_hw *hw);
void e1000_reset_adaptive(struct e1000_hw *hw);
void e1000_update_adaptive(struct e1000_hw *hw);
void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats, uint32_t frame_len, uint8_t * mac_addr);
uint32_t e1000_io_read(struct e1000_hw *hw, unsigned long port);
uint32_t e1000_read_reg_io(struct e1000_hw *hw, uint32_t offset);
void e1000_io_write(struct e1000_hw *hw, unsigned long port, uint32_t value);
-void e1000_write_reg_io(struct e1000_hw *hw, uint32_t offset, uint32_t value);
-int32_t e1000_config_dsp_after_link_change(struct e1000_hw *hw, boolean_t link_up);
-int32_t e1000_set_d3_lplu_state(struct e1000_hw *hw, boolean_t active);
-
-#define E1000_READ_REG_IO(a, reg) \
- e1000_read_reg_io((a), E1000_##reg)
-#define E1000_WRITE_REG_IO(a, reg, val) \
- e1000_write_reg_io((a), E1000_##reg, val)
+void e1000_enable_pciex_master(struct e1000_hw *hw);
+int32_t e1000_disable_pciex_master(struct e1000_hw *hw);
+int32_t e1000_get_software_semaphore(struct e1000_hw *hw);
+void e1000_release_software_semaphore(struct e1000_hw *hw);
+int32_t e1000_check_phy_reset_block(struct e1000_hw *hw);
/* PCI Device IDs */
#define E1000_DEV_ID_82542 0x1000
#define E1000_DEV_ID_82547GI 0x1075
#define E1000_DEV_ID_82541GI 0x1076
#define E1000_DEV_ID_82541GI_MOBILE 0x1077
+#define E1000_DEV_ID_82541GI_LF 0x107C
#define E1000_DEV_ID_82546GB_COPPER 0x1079
#define E1000_DEV_ID_82546GB_FIBER 0x107A
#define E1000_DEV_ID_82546GB_SERDES 0x107B
+#define E1000_DEV_ID_82546GB_PCIE 0x108A
+#define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099
#define E1000_DEV_ID_82547EI 0x1019
+#define E1000_DEV_ID_82571EB_COPPER 0x105E
+#define E1000_DEV_ID_82571EB_FIBER 0x105F
+#define E1000_DEV_ID_82571EB_SERDES 0x1060
+#define E1000_DEV_ID_82572EI_COPPER 0x107D
+#define E1000_DEV_ID_82572EI_FIBER 0x107E
+#define E1000_DEV_ID_82572EI_SERDES 0x107F
+#define E1000_DEV_ID_82573E 0x108B
+#define E1000_DEV_ID_82573E_IAMT 0x108C
+#define E1000_DEV_ID_82573L 0x109A
+#define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5
+#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096
+#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098
+
#define NODE_ADDRESS_SIZE 6
#define ETH_LENGTH_OF_ADDRESS 6
#define E1000_REVISION_0 0
#define E1000_REVISION_1 1
#define E1000_REVISION_2 2
+#define E1000_REVISION_3 3
#define SPEED_10 10
#define SPEED_100 100
E1000_IMS_RXSEQ | \
E1000_IMS_LSC)
+
/* Number of high/low register pairs in the RAR. The RAR (Receive Address
* Registers) holds the directed and multicast addresses that we monitor. We
* reserve one of these spots for our directed address, allowing us room for
uint16_t special;
};
+/* Receive Descriptor - Extended */
+union e1000_rx_desc_extended {
+ struct {
+ uint64_t buffer_addr;
+ uint64_t reserved;
+ } read;
+ struct {
+ struct {
+ uint32_t mrq; /* Multiple Rx Queues */
+ union {
+ uint32_t rss; /* RSS Hash */
+ struct {
+ uint16_t ip_id; /* IP id */
+ uint16_t csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ uint32_t status_error; /* ext status/error */
+ uint16_t length;
+ uint16_t vlan; /* VLAN tag */
+ } upper;
+ } wb; /* writeback */
+};
+
+#define MAX_PS_BUFFERS 4
+/* Receive Descriptor - Packet Split */
+union e1000_rx_desc_packet_split {
+ struct {
+ /* one buffer for protocol header(s), three data buffers */
+ uint64_t buffer_addr[MAX_PS_BUFFERS];
+ } read;
+ struct {
+ struct {
+ uint32_t mrq; /* Multiple Rx Queues */
+ union {
+ uint32_t rss; /* RSS Hash */
+ struct {
+ uint16_t ip_id; /* IP id */
+ uint16_t csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ uint32_t status_error; /* ext status/error */
+ uint16_t length0; /* length of buffer 0 */
+ uint16_t vlan; /* VLAN tag */
+ } middle;
+ struct {
+ uint16_t header_status;
+ uint16_t length[3]; /* length of buffers 1-3 */
+ } upper;
+ uint64_t reserved;
+ } wb; /* writeback */
+};
+
/* Receive Decriptor bit definitions */
#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
+#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum caculated */
#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */
#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */
+#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */
+#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */
+#define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */
#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */
-#define E1000_RXD_SPC_PRI_SHIFT 0x000D /* Priority is in upper 3 of 16 */
+#define E1000_RXD_SPC_PRI_SHIFT 13
#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */
-#define E1000_RXD_SPC_CFI_SHIFT 0x000C /* CFI is bit 12 */
+#define E1000_RXD_SPC_CFI_SHIFT 12
+
+#define E1000_RXDEXT_STATERR_CE 0x01000000
+#define E1000_RXDEXT_STATERR_SE 0x02000000
+#define E1000_RXDEXT_STATERR_SEQ 0x04000000
+#define E1000_RXDEXT_STATERR_CXE 0x10000000
+#define E1000_RXDEXT_STATERR_TCPE 0x20000000
+#define E1000_RXDEXT_STATERR_IPE 0x40000000
+#define E1000_RXDEXT_STATERR_RXE 0x80000000
+
+#define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000
+#define E1000_RXDPS_HDRSTAT_HDRLEN_MASK 0x000003FF
/* mask to determine if packets should be dropped due to frame errors */
#define E1000_RXD_ERR_FRAME_ERR_MASK ( \
E1000_RXD_ERR_CXE | \
E1000_RXD_ERR_RXE)
+
+/* Same mask, but for extended and packet split descriptors */
+#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
+ E1000_RXDEXT_STATERR_CE | \
+ E1000_RXDEXT_STATERR_SE | \
+ E1000_RXDEXT_STATERR_SEQ | \
+ E1000_RXDEXT_STATERR_CXE | \
+ E1000_RXDEXT_STATERR_RXE)
+
/* Transmit Descriptor */
struct e1000_tx_desc {
uint64_t buffer_addr; /* Address of the descriptor's data buffer */
#define E1000_FFMT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX
#define E1000_FFVT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX
+#define E1000_DISABLE_SERDES_LOOPBACK 0x0400
+
/* Register Set. (82543, 82544)
*
* Registers are defined to be 32 bits and should be accessed as 32 bit values.
#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */
#define E1000_FLA 0x0001C /* Flash Access - RW */
#define E1000_MDIC 0x00020 /* MDI Control - RW */
+#define E1000_SCTL 0x00024 /* SerDes Control - RW */
#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */
#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */
#define E1000_FCT 0x00030 /* Flow Control Type - RW */
#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */
#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */
#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */
+#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */
#define E1000_RCTL 0x00100 /* RX Control - RW */
+#define E1000_RDTR1 0x02820 /* RX Delay Timer (1) - RW */
+#define E1000_RDBAL1 0x02900 /* RX Descriptor Base Address Low (1) - RW */
+#define E1000_RDBAH1 0x02904 /* RX Descriptor Base Address High (1) - RW */
+#define E1000_RDLEN1 0x02908 /* RX Descriptor Length (1) - RW */
+#define E1000_RDH1 0x02910 /* RX Descriptor Head (1) - RW */
+#define E1000_RDT1 0x02918 /* RX Descriptor Tail (1) - RW */
#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */
#define E1000_TXCW 0x00178 /* TX Configuration Word - RW */
#define E1000_RXCW 0x00180 /* RX Configuration Word - RO */
#define E1000_TCTL 0x00400 /* TX Control - RW */
+#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */
#define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */
#define E1000_TBT 0x00448 /* TX Burst Timer - RW */
#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */
#define E1000_LEDCTL 0x00E00 /* LED Control - RW */
+#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */
+#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */
#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
+#define E1000_PBS 0x01008 /* Packet Buffer Size */
+#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
+#define E1000_FLASH_UPDATES 1000
+#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */
+#define E1000_FLASHT 0x01028 /* FLASH Timer Register */
+#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */
+#define E1000_FLSWCTL 0x01030 /* FLASH control register */
+#define E1000_FLSWDATA 0x01034 /* FLASH data register */
+#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */
+#define E1000_FLOP 0x0103C /* FLASH Opcode Register */
+#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */
#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */
#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */
+#define E1000_PSRCTL 0x02170 /* Packet Split Receive Control - RW */
#define E1000_RDBAL 0x02800 /* RX Descriptor Base Address Low - RW */
#define E1000_RDBAH 0x02804 /* RX Descriptor Base Address High - RW */
#define E1000_RDLEN 0x02808 /* RX Descriptor Length - RW */
#define E1000_RDH 0x02810 /* RX Descriptor Head - RW */
#define E1000_RDT 0x02818 /* RX Descriptor Tail - RW */
#define E1000_RDTR 0x02820 /* RX Delay Timer - RW */
+#define E1000_RDBAL0 E1000_RDBAL /* RX Desc Base Address Low (0) - RW */
+#define E1000_RDBAH0 E1000_RDBAH /* RX Desc Base Address High (0) - RW */
+#define E1000_RDLEN0 E1000_RDLEN /* RX Desc Length (0) - RW */
+#define E1000_RDH0 E1000_RDH /* RX Desc Head (0) - RW */
+#define E1000_RDT0 E1000_RDT /* RX Desc Tail (0) - RW */
+#define E1000_RDTR0 E1000_RDTR /* RX Delay Timer (0) - RW */
#define E1000_RXDCTL 0x02828 /* RX Descriptor Control - RW */
#define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */
#define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */
+#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */
#define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */
#define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */
#define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */
#define E1000_TXDCTL 0x03828 /* TX Descriptor Control - RW */
#define E1000_TADV 0x0382C /* TX Interrupt Absolute Delay Val - RW */
#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */
+#define E1000_TARC0 0x03840 /* TX Arbitration Count (0) */
+#define E1000_TDBAL1 0x03900 /* TX Desc Base Address Low (1) - RW */
+#define E1000_TDBAH1 0x03904 /* TX Desc Base Address High (1) - RW */
+#define E1000_TDLEN1 0x03908 /* TX Desc Length (1) - RW */
+#define E1000_TDH1 0x03910 /* TX Desc Head (1) - RW */
+#define E1000_TDT1 0x03918 /* TX Desc Tail (1) - RW */
+#define E1000_TXDCTL1 0x03928 /* TX Descriptor Control (1) - RW */
+#define E1000_TARC1 0x03940 /* TX Arbitration Count (1) */
#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */
#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */
#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */
#define E1000_BPTC 0x040F4 /* Broadcast Packets TX Count - R/clr */
#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context TX - R/clr */
#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context TX Fail - R/clr */
+#define E1000_IAC 0x04100 /* Interrupt Assertion Count */
+#define E1000_ICRXPTC 0x04104 /* Interrupt Cause Rx Packet Timer Expire Count */
+#define E1000_ICRXATC 0x04108 /* Interrupt Cause Rx Absolute Timer Expire Count */
+#define E1000_ICTXPTC 0x0410C /* Interrupt Cause Tx Packet Timer Expire Count */
+#define E1000_ICTXATC 0x04110 /* Interrupt Cause Tx Absolute Timer Expire Count */
+#define E1000_ICTXQEC 0x04118 /* Interrupt Cause Tx Queue Empty Count */
+#define E1000_ICTXQMTC 0x0411C /* Interrupt Cause Tx Queue Minimum Threshold Count */
+#define E1000_ICRXDMTC 0x04120 /* Interrupt Cause Rx Descriptor Minimum Threshold Count */
+#define E1000_ICRXOC 0x04124 /* Interrupt Cause Receiver Overrun Count */
#define E1000_RXCSUM 0x05000 /* RX Checksum Control - RW */
+#define E1000_RFCTL 0x05008 /* Receive Filter Control*/
#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */
#define E1000_RA 0x05400 /* Receive Address - RW Array */
#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */
#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */
#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */
+#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */
+#define E1000_MDPHYA 0x0003C /* PHY address - RW */
+#define E1000_MANC2H 0x05860 /* Managment Control To Host - RW */
+#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */
+
+#define E1000_GCR 0x05B00 /* PCI-Ex Control */
+#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */
+#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */
+#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */
+#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */
+#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */
+#define E1000_SWSM 0x05B50 /* SW Semaphore */
+#define E1000_FWSM 0x05B54 /* FW Semaphore */
+#define E1000_FFLT_DBG 0x05F04 /* Debug Register */
+#define E1000_HICR 0x08F00 /* Host Inteface Control */
+
+/* RSS registers */
+#define E1000_CPUVEC 0x02C10 /* CPU Vector Register - RW */
+#define E1000_MRQC 0x05818 /* Multiple Receive Control - RW */
+#define E1000_RETA 0x05C00 /* Redirection Table - RW Array */
+#define E1000_RSSRK 0x05C80 /* RSS Random Key - RW Array */
+#define E1000_RSSIM 0x05864 /* RSS Interrupt Mask */
+#define E1000_RSSIR 0x05868 /* RSS Interrupt Request */
/* Register Set (82542)
*
* Some of the 82542 registers are located at different offsets than they are
#define E1000_82542_CTRL_EXT E1000_CTRL_EXT
#define E1000_82542_FLA E1000_FLA
#define E1000_82542_MDIC E1000_MDIC
+#define E1000_82542_SCTL E1000_SCTL
#define E1000_82542_FCAL E1000_FCAL
#define E1000_82542_FCAH E1000_FCAH
#define E1000_82542_FCT E1000_FCT
#define E1000_82542_RDLEN 0x00118
#define E1000_82542_RDH 0x00120
#define E1000_82542_RDT 0x00128
+#define E1000_82542_RDTR0 E1000_82542_RDTR
+#define E1000_82542_RDBAL0 E1000_82542_RDBAL
+#define E1000_82542_RDBAH0 E1000_82542_RDBAH
+#define E1000_82542_RDLEN0 E1000_82542_RDLEN
+#define E1000_82542_RDH0 E1000_82542_RDH
+#define E1000_82542_RDT0 E1000_82542_RDT
+#define E1000_82542_RDTR1 0x00130
+#define E1000_82542_RDBAL1 0x00138
+#define E1000_82542_RDBAH1 0x0013C
+#define E1000_82542_RDLEN1 0x00140
+#define E1000_82542_RDH1 0x00148
+#define E1000_82542_RDT1 0x00150
#define E1000_82542_FCRTH 0x00160
#define E1000_82542_FCRTL 0x00168
#define E1000_82542_FCTTV E1000_FCTTV
#define E1000_82542_RXCW E1000_RXCW
#define E1000_82542_MTA 0x00200
#define E1000_82542_TCTL E1000_TCTL
+#define E1000_82542_TCTL_EXT E1000_TCTL_EXT
#define E1000_82542_TIPG E1000_TIPG
#define E1000_82542_TDBAL 0x00420
#define E1000_82542_TDBAH 0x00424
#define E1000_82542_VFTA 0x00600
#define E1000_82542_LEDCTL E1000_LEDCTL
#define E1000_82542_PBA E1000_PBA
+#define E1000_82542_PBS E1000_PBS
+#define E1000_82542_EEMNGCTL E1000_EEMNGCTL
+#define E1000_82542_EEARBC E1000_EEARBC
+#define E1000_82542_FLASHT E1000_FLASHT
+#define E1000_82542_EEWR E1000_EEWR
+#define E1000_82542_FLSWCTL E1000_FLSWCTL
+#define E1000_82542_FLSWDATA E1000_FLSWDATA
+#define E1000_82542_FLSWCNT E1000_FLSWCNT
+#define E1000_82542_FLOP E1000_FLOP
+#define E1000_82542_EXTCNF_CTRL E1000_EXTCNF_CTRL
+#define E1000_82542_EXTCNF_SIZE E1000_EXTCNF_SIZE
+#define E1000_82542_ERT E1000_ERT
#define E1000_82542_RXDCTL E1000_RXDCTL
#define E1000_82542_RADV E1000_RADV
#define E1000_82542_RSRPD E1000_RSRPD
#define E1000_82542_FFMT E1000_FFMT
#define E1000_82542_FFVT E1000_FFVT
#define E1000_82542_HOST_IF E1000_HOST_IF
+#define E1000_82542_IAM E1000_IAM
+#define E1000_82542_EEMNGCTL E1000_EEMNGCTL
+#define E1000_82542_PSRCTL E1000_PSRCTL
+#define E1000_82542_RAID E1000_RAID
+#define E1000_82542_TARC0 E1000_TARC0
+#define E1000_82542_TDBAL1 E1000_TDBAL1
+#define E1000_82542_TDBAH1 E1000_TDBAH1
+#define E1000_82542_TDLEN1 E1000_TDLEN1
+#define E1000_82542_TDH1 E1000_TDH1
+#define E1000_82542_TDT1 E1000_TDT1
+#define E1000_82542_TXDCTL1 E1000_TXDCTL1
+#define E1000_82542_TARC1 E1000_TARC1
+#define E1000_82542_RFCTL E1000_RFCTL
+#define E1000_82542_GCR E1000_GCR
+#define E1000_82542_GSCL_1 E1000_GSCL_1
+#define E1000_82542_GSCL_2 E1000_GSCL_2
+#define E1000_82542_GSCL_3 E1000_GSCL_3
+#define E1000_82542_GSCL_4 E1000_GSCL_4
+#define E1000_82542_FACTPS E1000_FACTPS
+#define E1000_82542_SWSM E1000_SWSM
+#define E1000_82542_FWSM E1000_FWSM
+#define E1000_82542_FFLT_DBG E1000_FFLT_DBG
+#define E1000_82542_IAC E1000_IAC
+#define E1000_82542_ICRXPTC E1000_ICRXPTC
+#define E1000_82542_ICRXATC E1000_ICRXATC
+#define E1000_82542_ICTXPTC E1000_ICTXPTC
+#define E1000_82542_ICTXATC E1000_ICTXATC
+#define E1000_82542_ICTXQEC E1000_ICTXQEC
+#define E1000_82542_ICTXQMTC E1000_ICTXQMTC
+#define E1000_82542_ICRXDMTC E1000_ICRXDMTC
+#define E1000_82542_ICRXOC E1000_ICRXOC
+#define E1000_82542_HICR E1000_HICR
+
+#define E1000_82542_CPUVEC E1000_CPUVEC
+#define E1000_82542_MRQC E1000_MRQC
+#define E1000_82542_RETA E1000_RETA
+#define E1000_82542_RSSRK E1000_RSSRK
+#define E1000_82542_RSSIM E1000_RSSIM
+#define E1000_82542_RSSIR E1000_RSSIR
+#define E1000_82542_KUMCTRLSTA E1000_KUMCTRLSTA
+#define E1000_82542_SW_FW_SYNC E1000_SW_FW_SYNC
/* Statistics counters collected by the MAC */
struct e1000_hw_stats {
uint64_t bptc;
uint64_t tsctc;
uint64_t tsctfc;
+ uint64_t iac;
+ uint64_t icrxptc;
+ uint64_t icrxatc;
+ uint64_t ictxptc;
+ uint64_t ictxatc;
+ uint64_t ictxqec;
+ uint64_t ictxqmtc;
+ uint64_t icrxdmtc;
+ uint64_t icrxoc;
};
/* Structure containing variables used by the shared code (e1000_hw.c) */
struct e1000_hw {
- uint8_t *hw_addr;
+ uint8_t __iomem *hw_addr;
+ uint8_t *flash_address;
e1000_mac_type mac_type;
e1000_phy_type phy_type;
uint32_t phy_init_script;
e1000_ms_type original_master_slave;
e1000_ffe_config ffe_config_state;
uint32_t asf_firmware_present;
+ uint32_t eeprom_semaphore_present;
+ uint32_t swfw_sync_present;
unsigned long io_base;
uint32_t phy_id;
uint32_t phy_revision;
uint32_t ledctl_default;
uint32_t ledctl_mode1;
uint32_t ledctl_mode2;
+ boolean_t tx_pkt_filtering;
+ struct e1000_host_mng_dhcp_cookie mng_cookie;
uint16_t phy_spd_default;
uint16_t autoneg_advertised;
uint16_t pci_cmd_word;
uint8_t perm_mac_addr[NODE_ADDRESS_SIZE];
boolean_t disable_polarity_correction;
boolean_t speed_downgraded;
+ e1000_smart_speed smart_speed;
e1000_dsp_config dsp_config_state;
boolean_t get_link_status;
boolean_t serdes_link_down;
boolean_t tbi_compatibility_en;
boolean_t tbi_compatibility_on;
+ boolean_t laa_is_present;
boolean_t phy_reset_disable;
boolean_t fc_send_xon;
boolean_t fc_strict_ieee;
boolean_t adaptive_ifs;
boolean_t ifs_params_forced;
boolean_t in_ifs_mode;
+ boolean_t mng_reg_access_disabled;
+ boolean_t leave_av_bit_off;
};
#define E1000_EEPROM_SWDPIN0 0x0001 /* SWDPIN 0 EEPROM Value */
#define E1000_EEPROM_LED_LOGIC 0x0020 /* Led Logic Word */
-
+#define E1000_EEPROM_RW_REG_DATA 16 /* Offset to data in EEPROM read/write registers */
+#define E1000_EEPROM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
+#define E1000_EEPROM_RW_REG_START 1 /* First bit for telling part to start operation */
+#define E1000_EEPROM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
+#define E1000_EEPROM_POLL_WRITE 1 /* Flag for polling for write complete */
+#define E1000_EEPROM_POLL_READ 0 /* Flag for polling for read complete */
/* Register Bit Masks */
/* Device Control */
#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
#define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */
#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */
+#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
#define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */
#define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */
#define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */
#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
+#define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */
+#define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock indication in SDP[0] */
+#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through PHYRST_N pin */
+#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external LINK_0 and LINK_1 pins */
#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */
#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
+#define E1000_STATUS_FUNC_SHIFT 2
#define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */
#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */
+#define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. Clear on write '0'. */
+#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
#define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */
#define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */
#define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */
#define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */
#define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */
+#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */
+#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */
+#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */
+#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */
+#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution disabled */
+#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */
+#define E1000_STATUS_FUSE_8 0x04000000
+#define E1000_STATUS_FUSE_9 0x08000000
+#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */
+#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */
/* Constants used to intrepret the masked PCI-X bus speed. */
#define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */
#ifndef E1000_EEPROM_GRANT_ATTEMPTS
#define E1000_EEPROM_GRANT_ATTEMPTS 1000 /* EEPROM # attempts to gain grant */
#endif
+#define E1000_EECD_AUTO_RD 0x00000200 /* EEPROM Auto Read done */
+#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* EEprom Size */
+#define E1000_EECD_SIZE_EX_SHIFT 11
+#define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */
+#define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */
+#define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */
+#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */
+#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */
+#define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */
+#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
+#define E1000_EECD_SECVAL_SHIFT 22
+#define E1000_STM_OPCODE 0xDB00
+#define E1000_HICR_FW_RESET 0xC0
/* EEPROM Read */
#define E1000_EERD_START 0x00000001 /* Start Read */
#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
#define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */
#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
+#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000
#define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_KMRN 0x00000000
+#define E1000_CTRL_EXT_LINK_MODE_SERDES 0x00C00000
#define E1000_CTRL_EXT_WR_WMARK_MASK 0x03000000
#define E1000_CTRL_EXT_WR_WMARK_256 0x00000000
#define E1000_CTRL_EXT_WR_WMARK_320 0x01000000
#define E1000_CTRL_EXT_WR_WMARK_384 0x02000000
#define E1000_CTRL_EXT_WR_WMARK_448 0x03000000
+#define E1000_CTRL_EXT_CANC 0x04000000 /* Interrupt delay cancellation */
+#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
+#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
+#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
+#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error detection enabled */
+#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity error detection enable */
+#define E1000_CTRL_EXT_GHOST_PAREN 0x40000000
/* MDI Control */
#define E1000_MDIC_DATA_MASK 0x0000FFFF
#define E1000_MDIC_INT_EN 0x20000000
#define E1000_MDIC_ERROR 0x40000000
+#define E1000_KUMCTRLSTA_MASK 0x0000FFFF
+#define E1000_KUMCTRLSTA_OFFSET 0x001F0000
+#define E1000_KUMCTRLSTA_OFFSET_SHIFT 16
+#define E1000_KUMCTRLSTA_REN 0x00200000
+
+#define E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL 0x00000000
+#define E1000_KUMCTRLSTA_OFFSET_CTRL 0x00000001
+#define E1000_KUMCTRLSTA_OFFSET_INB_CTRL 0x00000002
+#define E1000_KUMCTRLSTA_OFFSET_DIAG 0x00000003
+#define E1000_KUMCTRLSTA_OFFSET_TIMEOUTS 0x00000004
+#define E1000_KUMCTRLSTA_OFFSET_INB_PARAM 0x00000009
+#define E1000_KUMCTRLSTA_OFFSET_HD_CTRL 0x00000010
+#define E1000_KUMCTRLSTA_OFFSET_M2P_SERDES 0x0000001E
+#define E1000_KUMCTRLSTA_OFFSET_M2P_MODES 0x0000001F
+
+/* FIFO Control */
+#define E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS 0x00000008
+#define E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS 0x00000800
+
+/* In-Band Control */
+#define E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING 0x00000010
+
+/* Half-Duplex Control */
+#define E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT 0x00000004
+#define E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT 0x00000000
+
/* LED Control */
#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
#define E1000_LEDCTL_LED0_MODE_SHIFT 0
+#define E1000_LEDCTL_LED0_BLINK_RATE 0x0000020
#define E1000_LEDCTL_LED0_IVRT 0x00000040
#define E1000_LEDCTL_LED0_BLINK 0x00000080
#define E1000_LEDCTL_LED1_MODE_MASK 0x00000F00
#define E1000_LEDCTL_LED1_MODE_SHIFT 8
+#define E1000_LEDCTL_LED1_BLINK_RATE 0x0002000
#define E1000_LEDCTL_LED1_IVRT 0x00004000
#define E1000_LEDCTL_LED1_BLINK 0x00008000
#define E1000_LEDCTL_LED2_MODE_MASK 0x000F0000
#define E1000_LEDCTL_LED2_MODE_SHIFT 16
+#define E1000_LEDCTL_LED2_BLINK_RATE 0x00200000
#define E1000_LEDCTL_LED2_IVRT 0x00400000
#define E1000_LEDCTL_LED2_BLINK 0x00800000
#define E1000_LEDCTL_LED3_MODE_MASK 0x0F000000
#define E1000_LEDCTL_LED3_MODE_SHIFT 24
+#define E1000_LEDCTL_LED3_BLINK_RATE 0x20000000
#define E1000_LEDCTL_LED3_IVRT 0x40000000
#define E1000_LEDCTL_LED3_BLINK 0x80000000
#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */
#define E1000_ICR_TXD_LOW 0x00008000
#define E1000_ICR_SRPD 0x00010000
+#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */
+#define E1000_ICR_MNG 0x00040000 /* Manageability event */
+#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */
+#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */
+#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity error */
+#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */
+#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */
/* Interrupt Cause Set */
#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
#define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW
#define E1000_ICS_SRPD E1000_ICR_SRPD
+#define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
/* Interrupt Mask Set */
#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
#define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW
#define E1000_IMS_SRPD E1000_ICR_SRPD
+#define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
/* Interrupt Mask Clear */
#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */
#define E1000_IMC_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
#define E1000_IMC_TXD_LOW E1000_ICR_TXD_LOW
#define E1000_IMC_SRPD E1000_ICR_SRPD
+#define E1000_IMC_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_IMC_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_IMC_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_IMC_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_IMC_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_IMC_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
/* Receive Control */
#define E1000_RCTL_RST 0x00000001 /* Software reset */
#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */
#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
+#define E1000_RCTL_DTYP_MASK 0x00000C00 /* Descriptor type mask */
+#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */
#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */
#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
+#define E1000_RCTL_FLXBUF_MASK 0x78000000 /* Flexible buffer size */
+#define E1000_RCTL_FLXBUF_SHIFT 27 /* Flexible buffer shift */
+
+/* Use byte values for the following shift parameters
+ * Usage:
+ * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
+ * E1000_PSRCTL_BSIZE0_MASK) |
+ * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
+ * E1000_PSRCTL_BSIZE1_MASK) |
+ * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
+ * E1000_PSRCTL_BSIZE2_MASK) |
+ * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
+ * E1000_PSRCTL_BSIZE3_MASK))
+ * where value0 = [128..16256], default=256
+ * value1 = [1024..64512], default=4096
+ * value2 = [0..64512], default=4096
+ * value3 = [0..64512], default=0
+ */
+
+#define E1000_PSRCTL_BSIZE0_MASK 0x0000007F
+#define E1000_PSRCTL_BSIZE1_MASK 0x00003F00
+#define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
+#define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
+
+#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
+#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
+#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
+#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
+
+/* SW_W_SYNC definitions */
+#define E1000_SWFW_EEP_SM 0x0001
+#define E1000_SWFW_PHY0_SM 0x0002
+#define E1000_SWFW_PHY1_SM 0x0004
+#define E1000_SWFW_MAC_CSR_SM 0x0008
/* Receive Descriptor */
#define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */
#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */
#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
+/* Header split receive */
+#define E1000_RFCTL_ISCSI_DIS 0x00000001
+#define E1000_RFCTL_ISCSI_DWC_MASK 0x0000003E
+#define E1000_RFCTL_ISCSI_DWC_SHIFT 1
+#define E1000_RFCTL_NFSW_DIS 0x00000040
+#define E1000_RFCTL_NFSR_DIS 0x00000080
+#define E1000_RFCTL_NFS_VER_MASK 0x00000300
+#define E1000_RFCTL_NFS_VER_SHIFT 8
+#define E1000_RFCTL_IPV6_DIS 0x00000400
+#define E1000_RFCTL_IPV6_XSUM_DIS 0x00000800
+#define E1000_RFCTL_ACK_DIS 0x00001000
+#define E1000_RFCTL_ACKD_DIS 0x00002000
+#define E1000_RFCTL_IPFRSP_DIS 0x00004000
+#define E1000_RFCTL_EXTEN 0x00008000
+#define E1000_RFCTL_IPV6_EX_DIS 0x00010000
+#define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000
+
/* Receive Descriptor Control */
#define E1000_RXDCTL_PTHRESH 0x0000003F /* RXDCTL Prefetch Threshold */
#define E1000_RXDCTL_HTHRESH 0x00003F00 /* RXDCTL Host Threshold */
#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */
#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */
#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
-
+#define E1000_TXDCTL_COUNT_DESC 0x00400000 /* Enable the counting of desc.
+ still to be processed. */
/* Transmit Configuration Word */
#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */
#define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */
#define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */
#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
#define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */
+#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
+/* Extended Transmit Control */
+#define E1000_TCTL_EXT_BST_MASK 0x000003FF /* Backoff Slot Time */
+#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
+
+#define DEFAULT_80003ES2LAN_TCTL_EXT_GCEX 0x00010000
/* Receive Checksum Control */
#define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */
#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */
#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
#define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */
+#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
+#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
+
+/* Multiple Receive Queue Control */
+#define E1000_MRQC_ENABLE_MASK 0x00000003
+#define E1000_MRQC_ENABLE_RSS_2Q 0x00000001
+#define E1000_MRQC_ENABLE_RSS_INT 0x00000004
+#define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000
+#define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
+#define E1000_MRQC_RSS_FIELD_IPV4 0x00020000
+#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00040000
+#define E1000_MRQC_RSS_FIELD_IPV6_EX 0x00080000
+#define E1000_MRQC_RSS_FIELD_IPV6 0x00100000
/* Definitions for power management and wakeup registers */
/* Wake Up Control */
#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */
#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */
+#define E1000_WUFC_IGNORE_TCO 0x00008000 /* Ignore WakeOn TCO packets */
#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */
#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */
#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */
#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
#define E1000_MANC_NEIGHBOR_EN 0x00004000 /* Enable Neighbor Discovery
* Filtering */
+#define E1000_MANC_ARP_RES_EN 0x00008000 /* Enable ARP response Filtering */
#define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */
#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */
+#define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */
+#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 /* Enable MAC address
* filtering */
#define E1000_MANC_EN_MNG2HOST 0x00200000 /* Enable MNG packets to host
* memory */
+#define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000 /* Enable IP address
+ * filtering */
+#define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */
+#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */
#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */
#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */
#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */
#define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */
#define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */
+/* SW Semaphore Register */
+#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
+#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
+#define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */
+#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */
+
+/* FW Semaphore Register */
+#define E1000_FWSM_MODE_MASK 0x0000000E /* FW mode */
+#define E1000_FWSM_MODE_SHIFT 1
+#define E1000_FWSM_FW_VALID 0x00008000 /* FW established a valid mode */
+
+/* FFLT Debug Register */
+#define E1000_FFLT_DBG_INVC 0x00100000 /* Invalid /C/ code handling */
+
+typedef enum {
+ e1000_mng_mode_none = 0,
+ e1000_mng_mode_asf,
+ e1000_mng_mode_pt,
+ e1000_mng_mode_ipmi,
+ e1000_mng_mode_host_interface_only
+} e1000_mng_mode;
+
+/* Host Inteface Control Register */
+#define E1000_HICR_EN 0x00000001 /* Enable Bit - RO */
+#define E1000_HICR_C 0x00000002 /* Driver sets this bit when done
+ * to put command in RAM */
+#define E1000_HICR_SV 0x00000004 /* Status Validity */
+#define E1000_HICR_FWR 0x00000080 /* FW reset. Set by the Host */
+
+/* Host Interface Command Interface - Address range 0x8800-0x8EFF */
+#define E1000_HI_MAX_DATA_LENGTH 252 /* Host Interface data length */
+#define E1000_HI_MAX_BLOCK_BYTE_LENGTH 1792 /* Number of bytes in range */
+#define E1000_HI_MAX_BLOCK_DWORD_LENGTH 448 /* Number of dwords in range */
+#define E1000_HI_COMMAND_TIMEOUT 500 /* Time in ms to process HI command */
+
+struct e1000_host_command_header {
+ uint8_t command_id;
+ uint8_t command_length;
+ uint8_t command_options; /* I/F bits for command, status for return */
+ uint8_t checksum;
+};
+struct e1000_host_command_info {
+ struct e1000_host_command_header command_header; /* Command Head/Command Result Head has 4 bytes */
+ uint8_t command_data[E1000_HI_MAX_DATA_LENGTH]; /* Command data can length 0..252 */
+};
+
+/* Host SMB register #0 */
+#define E1000_HSMC0R_CLKIN 0x00000001 /* SMB Clock in */
+#define E1000_HSMC0R_DATAIN 0x00000002 /* SMB Data in */
+#define E1000_HSMC0R_DATAOUT 0x00000004 /* SMB Data out */
+#define E1000_HSMC0R_CLKOUT 0x00000008 /* SMB Clock out */
+
+/* Host SMB register #1 */
+#define E1000_HSMC1R_CLKIN E1000_HSMC0R_CLKIN
+#define E1000_HSMC1R_DATAIN E1000_HSMC0R_DATAIN
+#define E1000_HSMC1R_DATAOUT E1000_HSMC0R_DATAOUT
+#define E1000_HSMC1R_CLKOUT E1000_HSMC0R_CLKOUT
+
+/* FW Status Register */
+#define E1000_FWSTS_FWS_MASK 0x000000FF /* FW Status */
+
/* Wake Up Packet Length */
#define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */
#define E1000_MDALIGN 4096
+/* PCI-Ex registers */
+
+/* PCI-Ex Control Register */
+#define E1000_GCR_RXD_NO_SNOOP 0x00000001
+#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002
+#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004
+#define E1000_GCR_TXD_NO_SNOOP 0x00000008
+#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010
+#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020
+
+#define PCI_EX_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \
+ E1000_GCR_RXDSCW_NO_SNOOP | \
+ E1000_GCR_RXDSCR_NO_SNOOP | \
+ E1000_GCR_TXD_NO_SNOOP | \
+ E1000_GCR_TXDSCW_NO_SNOOP | \
+ E1000_GCR_TXDSCR_NO_SNOOP)
+
+#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
+/* Function Active and Power State to MNG */
+#define E1000_FACTPS_FUNC0_POWER_STATE_MASK 0x00000003
+#define E1000_FACTPS_LAN0_VALID 0x00000004
+#define E1000_FACTPS_FUNC0_AUX_EN 0x00000008
+#define E1000_FACTPS_FUNC1_POWER_STATE_MASK 0x000000C0
+#define E1000_FACTPS_FUNC1_POWER_STATE_SHIFT 6
+#define E1000_FACTPS_LAN1_VALID 0x00000100
+#define E1000_FACTPS_FUNC1_AUX_EN 0x00000200
+#define E1000_FACTPS_FUNC2_POWER_STATE_MASK 0x00003000
+#define E1000_FACTPS_FUNC2_POWER_STATE_SHIFT 12
+#define E1000_FACTPS_IDE_ENABLE 0x00004000
+#define E1000_FACTPS_FUNC2_AUX_EN 0x00008000
+#define E1000_FACTPS_FUNC3_POWER_STATE_MASK 0x000C0000
+#define E1000_FACTPS_FUNC3_POWER_STATE_SHIFT 18
+#define E1000_FACTPS_SP_ENABLE 0x00100000
+#define E1000_FACTPS_FUNC3_AUX_EN 0x00200000
+#define E1000_FACTPS_FUNC4_POWER_STATE_MASK 0x03000000
+#define E1000_FACTPS_FUNC4_POWER_STATE_SHIFT 24
+#define E1000_FACTPS_IPMI_ENABLE 0x04000000
+#define E1000_FACTPS_FUNC4_AUX_EN 0x08000000
+#define E1000_FACTPS_MNGCG 0x20000000
+#define E1000_FACTPS_LAN_FUNC_SEL 0x40000000
+#define E1000_FACTPS_PM_STATE_CHANGED 0x80000000
+
/* EEPROM Commands - Microwire */
#define EEPROM_READ_OPCODE_MICROWIRE 0x6 /* EEPROM read opcode */
#define EEPROM_WRITE_OPCODE_MICROWIRE 0x5 /* EEPROM write opcode */
/* EEPROM Commands - SPI */
#define EEPROM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
-#define EEPROM_READ_OPCODE_SPI 0x3 /* EEPROM read opcode */
-#define EEPROM_WRITE_OPCODE_SPI 0x2 /* EEPROM write opcode */
-#define EEPROM_A8_OPCODE_SPI 0x8 /* opcode bit-3 = address bit-8 */
-#define EEPROM_WREN_OPCODE_SPI 0x6 /* EEPROM set Write Enable latch */
-#define EEPROM_WRDI_OPCODE_SPI 0x4 /* EEPROM reset Write Enable latch */
-#define EEPROM_RDSR_OPCODE_SPI 0x5 /* EEPROM read Status register */
-#define EEPROM_WRSR_OPCODE_SPI 0x1 /* EEPROM write Status register */
+#define EEPROM_READ_OPCODE_SPI 0x03 /* EEPROM read opcode */
+#define EEPROM_WRITE_OPCODE_SPI 0x02 /* EEPROM write opcode */
+#define EEPROM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
+#define EEPROM_WREN_OPCODE_SPI 0x06 /* EEPROM set Write Enable latch */
+#define EEPROM_WRDI_OPCODE_SPI 0x04 /* EEPROM reset Write Enable latch */
+#define EEPROM_RDSR_OPCODE_SPI 0x05 /* EEPROM read Status register */
+#define EEPROM_WRSR_OPCODE_SPI 0x01 /* EEPROM write Status register */
+#define EEPROM_ERASE4K_OPCODE_SPI 0x20 /* EEPROM ERASE 4KB */
+#define EEPROM_ERASE64K_OPCODE_SPI 0xD8 /* EEPROM ERASE 64KB */
+#define EEPROM_ERASE256_OPCODE_SPI 0xDB /* EEPROM ERASE 256B */
/* EEPROM Size definitions */
-#define EEPROM_SIZE_16KB 0x1800
-#define EEPROM_SIZE_8KB 0x1400
-#define EEPROM_SIZE_4KB 0x1000
-#define EEPROM_SIZE_2KB 0x0C00
-#define EEPROM_SIZE_1KB 0x0800
-#define EEPROM_SIZE_512B 0x0400
-#define EEPROM_SIZE_128B 0x0000
+#define EEPROM_WORD_SIZE_SHIFT 6
+#define EEPROM_SIZE_SHIFT 10
#define EEPROM_SIZE_MASK 0x1C00
/* EEPROM Word Offsets */
#define EEPROM_COMPAT 0x0003
#define EEPROM_ID_LED_SETTINGS 0x0004
+#define EEPROM_VERSION 0x0005
#define EEPROM_SERDES_AMPLITUDE 0x0006 /* For SERDES output amplitude adjustment. */
#define EEPROM_PHY_CLASS_WORD 0x0007
#define EEPROM_INIT_CONTROL1_REG 0x000A
#define EEPROM_INIT_CONTROL2_REG 0x000F
#define EEPROM_INIT_CONTROL3_PORT_B 0x0014
+#define EEPROM_INIT_3GIO_3 0x001A
#define EEPROM_INIT_CONTROL3_PORT_A 0x0024
#define EEPROM_CFG 0x0012
#define EEPROM_FLASH_VERSION 0x0032
#define EEPROM_CHECKSUM_REG 0x003F
+#define E1000_EEPROM_CFG_DONE 0x00040000 /* MNG config cycle done */
+#define E1000_EEPROM_CFG_DONE_PORT_1 0x00080000 /* ...for second port */
+
/* Word definitions for ID LED Settings */
#define ID_LED_RESERVED_0000 0x0000
#define ID_LED_RESERVED_FFFF 0xFFFF
#define EEPROM_WORD0F_ANE 0x0800
#define EEPROM_WORD0F_SWPDIO_EXT 0x00F0
+/* Mask bits for fields in Word 0x1a of the EEPROM */
+#define EEPROM_WORD1A_ASPM_MASK 0x000C
+
/* For checksumming, the sum of all words in the EEPROM should equal 0xBABA. */
#define EEPROM_SUM 0xBABA
/* Collision related configuration parameters */
#define E1000_COLLISION_THRESHOLD 15
#define E1000_CT_SHIFT 4
-#define E1000_COLLISION_DISTANCE 64
+/* Collision distance is a 0-based value that applies to
+ * half-duplex-capable hardware only. */
+#define E1000_COLLISION_DISTANCE 63
+#define E1000_COLLISION_DISTANCE_82542 64
#define E1000_FDX_COLLISION_DISTANCE E1000_COLLISION_DISTANCE
#define E1000_HDX_COLLISION_DISTANCE E1000_COLLISION_DISTANCE
#define E1000_COLD_SHIFT 12
#define DEFAULT_82542_TIPG_IPGR2 10
#define DEFAULT_82543_TIPG_IPGR2 6
+#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7
#define E1000_TIPG_IPGR2_SHIFT 20
+#define DEFAULT_80003ES2LAN_TIPG_IPGT_10_100 0x00000009
+#define DEFAULT_80003ES2LAN_TIPG_IPGT_1000 0x00000008
#define E1000_TXDMAC_DPP 0x00000001
/* Adaptive IFS defines */
#define IFS_MIN 40
#define IFS_RATIO 4
+/* Extended Configuration Control and Size */
+#define E1000_EXTCNF_CTRL_PCIE_WRITE_ENABLE 0x00000001
+#define E1000_EXTCNF_CTRL_PHY_WRITE_ENABLE 0x00000002
+#define E1000_EXTCNF_CTRL_D_UD_ENABLE 0x00000004
+#define E1000_EXTCNF_CTRL_D_UD_LATENCY 0x00000008
+#define E1000_EXTCNF_CTRL_D_UD_OWNER 0x00000010
+#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
+#define E1000_EXTCNF_CTRL_MDIO_HW_OWNERSHIP 0x00000040
+#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER 0x1FFF0000
+
+#define E1000_EXTCNF_SIZE_EXT_PHY_LENGTH 0x000000FF
+#define E1000_EXTCNF_SIZE_EXT_DOCK_LENGTH 0x0000FF00
+#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH 0x00FF0000
+
/* PBA constants */
+#define E1000_PBA_12K 0x000C /* 12KB, default Rx allocation */
#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */
#define E1000_PBA_22K 0x0016
#define E1000_PBA_24K 0x0018
#define E1000_PBA_30K 0x001E
+#define E1000_PBA_32K 0x0020
+#define E1000_PBA_38K 0x0026
#define E1000_PBA_40K 0x0028
#define E1000_PBA_48K 0x0030 /* 48KB, default RX allocation */
/* Number of milliseconds we wait for auto-negotiation to complete */
#define LINK_UP_TIMEOUT 500
+/* Number of 100 microseconds we wait for PCI Express master disable */
+#define MASTER_DISABLE_TIMEOUT 800
+/* Number of milliseconds we wait for Eeprom auto read bit done after MAC reset */
+#define AUTO_READ_DONE_TIMEOUT 10
+/* Number of milliseconds we wait for PHY configuration done after MAC reset */
+#define PHY_CFG_TIMEOUT 40
+
#define E1000_TX_BUFFER_SIZE ((uint32_t)1514)
/* The carrier extension symbol, as received by the NIC. */
#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */
+#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
+#define MAX_PHY_MULTI_PAGE_REG 0xF /* Registers equal on all pages */
+
/* M88E1000 Specific Registers */
#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health Register */
#define IGP01E1000_GMII_FIFO 0x14 /* GMII FIFO Register */
#define IGP01E1000_PHY_CHANNEL_QUALITY 0x15 /* PHY Channel Quality Register */
+#define IGP02E1000_PHY_POWER_MGMT 0x19
#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* PHY Page Select Core Register */
/* IGP01E1000 AGC Registers - stores the cable length values*/
#define IGP01E1000_PHY_AGC_C 0x1472
#define IGP01E1000_PHY_AGC_D 0x1872
+/* IGP02E1000 AGC Registers for cable length values */
+#define IGP02E1000_PHY_AGC_A 0x11B1
+#define IGP02E1000_PHY_AGC_B 0x12B1
+#define IGP02E1000_PHY_AGC_C 0x14B1
+#define IGP02E1000_PHY_AGC_D 0x18B1
+
/* IGP01E1000 DSP Reset Register */
#define IGP01E1000_PHY_DSP_RESET 0x1F33
#define IGP01E1000_PHY_DSP_SET 0x1F71
#define IGP01E1000_PHY_DSP_FFE 0x1F35
#define IGP01E1000_PHY_CHANNEL_NUM 4
+#define IGP02E1000_PHY_CHANNEL_NUM 4
+
#define IGP01E1000_PHY_AGC_PARAM_A 0x1171
#define IGP01E1000_PHY_AGC_PARAM_B 0x1271
#define IGP01E1000_PHY_AGC_PARAM_C 0x1471
#define IGP01E1000_ANALOG_REGS_PAGE 0x20C0
-#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
-#define MAX_PHY_MULTI_PAGE_REG 0xF /*Registers that are equal on all pages*/
+/* Bits...
+ * 15-5: page
+ * 4-0: register offset
+ */
+#define GG82563_PAGE_SHIFT 5
+#define GG82563_REG(page, reg) \
+ (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
+#define GG82563_MIN_ALT_REG 30
+
+/* GG82563 Specific Registers */
+#define GG82563_PHY_SPEC_CTRL \
+ GG82563_REG(0, 16) /* PHY Specific Control */
+#define GG82563_PHY_SPEC_STATUS \
+ GG82563_REG(0, 17) /* PHY Specific Status */
+#define GG82563_PHY_INT_ENABLE \
+ GG82563_REG(0, 18) /* Interrupt Enable */
+#define GG82563_PHY_SPEC_STATUS_2 \
+ GG82563_REG(0, 19) /* PHY Specific Status 2 */
+#define GG82563_PHY_RX_ERR_CNTR \
+ GG82563_REG(0, 21) /* Receive Error Counter */
+#define GG82563_PHY_PAGE_SELECT \
+ GG82563_REG(0, 22) /* Page Select */
+#define GG82563_PHY_SPEC_CTRL_2 \
+ GG82563_REG(0, 26) /* PHY Specific Control 2 */
+#define GG82563_PHY_PAGE_SELECT_ALT \
+ GG82563_REG(0, 29) /* Alternate Page Select */
+#define GG82563_PHY_TEST_CLK_CTRL \
+ GG82563_REG(0, 30) /* Test Clock Control (use reg. 29 to select) */
+
+#define GG82563_PHY_MAC_SPEC_CTRL \
+ GG82563_REG(2, 21) /* MAC Specific Control Register */
+#define GG82563_PHY_MAC_SPEC_CTRL_2 \
+ GG82563_REG(2, 26) /* MAC Specific Control 2 */
+
+#define GG82563_PHY_DSP_DISTANCE \
+ GG82563_REG(5, 26) /* DSP Distance */
+
+/* Page 193 - Port Control Registers */
+#define GG82563_PHY_KMRN_MODE_CTRL \
+ GG82563_REG(193, 16) /* Kumeran Mode Control */
+#define GG82563_PHY_PORT_RESET \
+ GG82563_REG(193, 17) /* Port Reset */
+#define GG82563_PHY_REVISION_ID \
+ GG82563_REG(193, 18) /* Revision ID */
+#define GG82563_PHY_DEVICE_ID \
+ GG82563_REG(193, 19) /* Device ID */
+#define GG82563_PHY_PWR_MGMT_CTRL \
+ GG82563_REG(193, 20) /* Power Management Control */
+#define GG82563_PHY_RATE_ADAPT_CTRL \
+ GG82563_REG(193, 25) /* Rate Adaptation Control */
+
+/* Page 194 - KMRN Registers */
+#define GG82563_PHY_KMRN_FIFO_CTRL_STAT \
+ GG82563_REG(194, 16) /* FIFO's Control/Status */
+#define GG82563_PHY_KMRN_CTRL \
+ GG82563_REG(194, 17) /* Control */
+#define GG82563_PHY_INBAND_CTRL \
+ GG82563_REG(194, 18) /* Inband Control */
+#define GG82563_PHY_KMRN_DIAGNOSTIC \
+ GG82563_REG(194, 19) /* Diagnostic */
+#define GG82563_PHY_ACK_TIMEOUTS \
+ GG82563_REG(194, 20) /* Acknowledge Timeouts */
+#define GG82563_PHY_ADV_ABILITY \
+ GG82563_REG(194, 21) /* Advertised Ability */
+#define GG82563_PHY_LINK_PARTNER_ADV_ABILITY \
+ GG82563_REG(194, 23) /* Link Partner Advertised Ability */
+#define GG82563_PHY_ADV_NEXT_PAGE \
+ GG82563_REG(194, 24) /* Advertised Next Page */
+#define GG82563_PHY_LINK_PARTNER_ADV_NEXT_PAGE \
+ GG82563_REG(194, 25) /* Link Partner Advertised Next page */
+#define GG82563_PHY_KMRN_MISC \
+ GG82563_REG(194, 26) /* Misc. */
+
/* PHY Control Register */
#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */
#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */
#define IGP01E1000_MSE_CHANNEL_B 0x0F00
#define IGP01E1000_MSE_CHANNEL_A 0xF000
+#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */
+#define IGP02E1000_PM_D3_LPLU 0x0004 /* Enable LPLU in non-D0a modes */
+#define IGP02E1000_PM_D0_LPLU 0x0002 /* Enable LPLU in D0a mode */
+
/* IGP01E1000 DSP reset macros */
#define DSP_RESET_ENABLE 0x0
#define DSP_RESET_DISABLE 0x2
#define E1000_MAX_DSP_RESETS 10
-/* IGP01E1000 AGC Registers */
+/* IGP01E1000 & IGP02E1000 AGC Registers */
#define IGP01E1000_AGC_LENGTH_SHIFT 7 /* Coarse - 13:11, Fine - 10:7 */
+#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Coarse - 15:13, Fine - 12:9 */
+
+/* IGP02E1000 AGC Register Length 9-bit mask */
+#define IGP02E1000_AGC_LENGTH_MASK 0x7F
/* 7 bits (3 Coarse + 4 Fine) --> 128 optional values */
#define IGP01E1000_AGC_LENGTH_TABLE_SIZE 128
+#define IGP02E1000_AGC_LENGTH_TABLE_SIZE 113
-/* The precision of the length is +/- 10 meters */
+/* The precision error of the cable length is +/- 10 meters */
#define IGP01E1000_AGC_RANGE 10
+#define IGP02E1000_AGC_RANGE 15
/* IGP01E1000 PCS Initialization register */
/* bits 3:6 in the PCS registers stores the channels polarity */
#define IGP01E1000_ANALOG_FUSE_FINE_1 0x0080
#define IGP01E1000_ANALOG_FUSE_FINE_10 0x0500
+/* GG82563 PHY Specific Status Register (Page 0, Register 16 */
+#define GG82563_PSCR_DISABLE_JABBER 0x0001 /* 1=Disable Jabber */
+#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Polarity Reversal Disabled */
+#define GG82563_PSCR_POWER_DOWN 0x0004 /* 1=Power Down */
+#define GG82563_PSCR_COPPER_TRANSMITER_DISABLE 0x0008 /* 1=Transmitter Disabled */
+#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060
+#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI configuration */
+#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX configuration */
+#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Automatic crossover */
+#define GG82563_PSCR_ENALBE_EXTENDED_DISTANCE 0x0080 /* 1=Enable Extended Distance */
+#define GG82563_PSCR_ENERGY_DETECT_MASK 0x0300
+#define GG82563_PSCR_ENERGY_DETECT_OFF 0x0000 /* 00,01=Off */
+#define GG82563_PSCR_ENERGY_DETECT_RX 0x0200 /* 10=Sense on Rx only (Energy Detect) */
+#define GG82563_PSCR_ENERGY_DETECT_RX_TM 0x0300 /* 11=Sense and Tx NLP */
+#define GG82563_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force Link Good */
+#define GG82563_PSCR_DOWNSHIFT_ENABLE 0x0800 /* 1=Enable Downshift */
+#define GG82563_PSCR_DOWNSHIFT_COUNTER_MASK 0x7000
+#define GG82563_PSCR_DOWNSHIFT_COUNTER_SHIFT 12
+
+/* PHY Specific Status Register (Page 0, Register 17) */
+#define GG82563_PSSR_JABBER 0x0001 /* 1=Jabber */
+#define GG82563_PSSR_POLARITY 0x0002 /* 1=Polarity Reversed */
+#define GG82563_PSSR_LINK 0x0008 /* 1=Link is Up */
+#define GG82563_PSSR_ENERGY_DETECT 0x0010 /* 1=Sleep, 0=Active */
+#define GG82563_PSSR_DOWNSHIFT 0x0020 /* 1=Downshift */
+#define GG82563_PSSR_CROSSOVER_STATUS 0x0040 /* 1=MDIX, 0=MDI */
+#define GG82563_PSSR_RX_PAUSE_ENABLED 0x0100 /* 1=Receive Pause Enabled */
+#define GG82563_PSSR_TX_PAUSE_ENABLED 0x0200 /* 1=Transmit Pause Enabled */
+#define GG82563_PSSR_LINK_UP 0x0400 /* 1=Link Up */
+#define GG82563_PSSR_SPEED_DUPLEX_RESOLVED 0x0800 /* 1=Resolved */
+#define GG82563_PSSR_PAGE_RECEIVED 0x1000 /* 1=Page Received */
+#define GG82563_PSSR_DUPLEX 0x2000 /* 1-Full-Duplex */
+#define GG82563_PSSR_SPEED_MASK 0xC000
+#define GG82563_PSSR_SPEED_10MBPS 0x0000 /* 00=10Mbps */
+#define GG82563_PSSR_SPEED_100MBPS 0x4000 /* 01=100Mbps */
+#define GG82563_PSSR_SPEED_1000MBPS 0x8000 /* 10=1000Mbps */
+
+/* PHY Specific Status Register 2 (Page 0, Register 19) */
+#define GG82563_PSSR2_JABBER 0x0001 /* 1=Jabber */
+#define GG82563_PSSR2_POLARITY_CHANGED 0x0002 /* 1=Polarity Changed */
+#define GG82563_PSSR2_ENERGY_DETECT_CHANGED 0x0010 /* 1=Energy Detect Changed */
+#define GG82563_PSSR2_DOWNSHIFT_INTERRUPT 0x0020 /* 1=Downshift Detected */
+#define GG82563_PSSR2_MDI_CROSSOVER_CHANGE 0x0040 /* 1=Crossover Changed */
+#define GG82563_PSSR2_FALSE_CARRIER 0x0100 /* 1=False Carrier */
+#define GG82563_PSSR2_SYMBOL_ERROR 0x0200 /* 1=Symbol Error */
+#define GG82563_PSSR2_LINK_STATUS_CHANGED 0x0400 /* 1=Link Status Changed */
+#define GG82563_PSSR2_AUTO_NEG_COMPLETED 0x0800 /* 1=Auto-Neg Completed */
+#define GG82563_PSSR2_PAGE_RECEIVED 0x1000 /* 1=Page Received */
+#define GG82563_PSSR2_DUPLEX_CHANGED 0x2000 /* 1=Duplex Changed */
+#define GG82563_PSSR2_SPEED_CHANGED 0x4000 /* 1=Speed Changed */
+#define GG82563_PSSR2_AUTO_NEG_ERROR 0x8000 /* 1=Auto-Neg Error */
+
+/* PHY Specific Control Register 2 (Page 0, Register 26) */
+#define GG82563_PSCR2_10BT_POLARITY_FORCE 0x0002 /* 1=Force Negative Polarity */
+#define GG82563_PSCR2_1000MB_TEST_SELECT_MASK 0x000C
+#define GG82563_PSCR2_1000MB_TEST_SELECT_NORMAL 0x0000 /* 00,01=Normal Operation */
+#define GG82563_PSCR2_1000MB_TEST_SELECT_112NS 0x0008 /* 10=Select 112ns Sequence */
+#define GG82563_PSCR2_1000MB_TEST_SELECT_16NS 0x000C /* 11=Select 16ns Sequence */
+#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000 /* 1=Reverse Auto-Negotiation */
+#define GG82563_PSCR2_1000BT_DISABLE 0x4000 /* 1=Disable 1000BASE-T */
+#define GG82563_PSCR2_TRANSMITER_TYPE_MASK 0x8000
+#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_B 0x0000 /* 0=Class B */
+#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_A 0x8000 /* 1=Class A */
+
+/* MAC Specific Control Register (Page 2, Register 21) */
+/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */
+#define GG82563_MSCR_TX_CLK_MASK 0x0007
+#define GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ 0x0004
+#define GG82563_MSCR_TX_CLK_100MBPS_25MHZ 0x0005
+#define GG82563_MSCR_TX_CLK_1000MBPS_2_5MHZ 0x0006
+#define GG82563_MSCR_TX_CLK_1000MBPS_25MHZ 0x0007
+
+#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */
+
+/* DSP Distance Register (Page 5, Register 26) */
+#define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M;
+ 1 = 50-80M;
+ 2 = 80-110M;
+ 3 = 110-140M;
+ 4 = >140M */
+
+/* Kumeran Mode Control Register (Page 193, Register 16) */
+#define GG82563_KMCR_PHY_LEDS_EN 0x0020 /* 1=PHY LEDs, 0=Kumeran Inband LEDs */
+#define GG82563_KMCR_FORCE_LINK_UP 0x0040 /* 1=Force Link Up */
+#define GG82563_KMCR_SUPPRESS_SGMII_EPD_EXT 0x0080
+#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT_MASK 0x0400
+#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT 0x0400 /* 1=6.25MHz, 0=0.8MHz */
+#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800
+
+/* Power Management Control Register (Page 193, Register 20) */
+#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001 /* 1=Enalbe SERDES Electrical Idle */
+#define GG82563_PMCR_DISABLE_PORT 0x0002 /* 1=Disable Port */
+#define GG82563_PMCR_DISABLE_SERDES 0x0004 /* 1=Disable SERDES */
+#define GG82563_PMCR_REVERSE_AUTO_NEG 0x0008 /* 1=Enable Reverse Auto-Negotiation */
+#define GG82563_PMCR_DISABLE_1000_NON_D0 0x0010 /* 1=Disable 1000Mbps Auto-Neg in non D0 */
+#define GG82563_PMCR_DISABLE_1000 0x0020 /* 1=Disable 1000Mbps Auto-Neg Always */
+#define GG82563_PMCR_REVERSE_AUTO_NEG_D0A 0x0040 /* 1=Enable D0a Reverse Auto-Negotiation */
+#define GG82563_PMCR_FORCE_POWER_STATE 0x0080 /* 1=Force Power State */
+#define GG82563_PMCR_PROGRAMMED_POWER_STATE_MASK 0x0300
+#define GG82563_PMCR_PROGRAMMED_POWER_STATE_DR 0x0000 /* 00=Dr */
+#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0U 0x0100 /* 01=D0u */
+#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0A 0x0200 /* 10=D0a */
+#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D3 0x0300 /* 11=D3 */
+
+/* In-Band Control Register (Page 194, Register 18) */
+#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding Use */
+
+
/* Bit definitions for valid PHY IDs. */
+/* I = Integrated
+ * E = External
+ */
#define M88E1000_E_PHY_ID 0x01410C50
#define M88E1000_I_PHY_ID 0x01410C30
#define M88E1011_I_PHY_ID 0x01410C20
#define M88E1000_12_PHY_ID M88E1000_E_PHY_ID
#define M88E1000_14_PHY_ID M88E1000_E_PHY_ID
#define M88E1011_I_REV_4 0x04
+#define M88E1111_I_PHY_ID 0x01410CC0
+#define L1LXT971A_PHY_ID 0x001378E0
+#define GG82563_E_PHY_ID 0x01410CA0
/* Miscellaneous PHY bit definitions. */
#define PHY_PREAMBLE 0xFFFFFFFF
git://git.onelab.eu / linux-2.6.git / blobdiff