--- /dev/null
+/* ne-h8300.c: A NE2000 clone on H8/300 driver for linux. */
+/*
+ original ne.c
+ Written 1992-94 by Donald Becker.
+
+ Copyright 1993 United States Government as represented by the
+ Director, National Security Agency.
+
+ This software may be used and distributed according to the terms
+ of the GNU General Public License, incorporated herein by reference.
+
+ The author may be reached as becker@scyld.com, or C/O
+ Scyld Computing Corporation, 410 Severn Ave., Suite 210, Annapolis MD 21403
+
+ H8/300 modified
+ Yoshinori Sato <ysato@users.sourceforge.jp>
+*/
+
+static const char version1[] =
+"ne-h8300.c:v1.00 2004/04/11 ysato\n";
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+
+#include <asm/system.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+
+#include "8390.h"
+
+/* Some defines that people can play with if so inclined. */
+
+/* Do we perform extra sanity checks on stuff ? */
+/* #define NE_SANITY_CHECK */
+
+/* Do we implement the read before write bugfix ? */
+/* #define NE_RW_BUGFIX */
+
+/* Do we have a non std. amount of memory? (in units of 256 byte pages) */
+/* #define PACKETBUF_MEMSIZE 0x40 */
+
+/* A zero-terminated list of I/O addresses to be probed at boot. */
+
+/* ---- No user-serviceable parts below ---- */
+
+#define NE_BASE (dev->base_addr)
+#define NE_CMD 0x00
+#define NE_DATAPORT (ei_status.word16?0x20:0x10) /* NatSemi-defined port window offset. */
+#define NE_RESET (ei_status.word16?0x3f:0x1f) /* Issue a read to reset, a write to clear. */
+#define NE_IO_EXTENT (ei_status.word16?0x40:0x20)
+
+#define NESM_START_PG 0x40 /* First page of TX buffer */
+#define NESM_STOP_PG 0x80 /* Last page +1 of RX ring */
+
+static int ne_probe1(struct net_device *dev, int ioaddr);
+
+static int ne_open(struct net_device *dev);
+static int ne_close(struct net_device *dev);
+
+static void ne_reset_8390(struct net_device *dev);
+static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
+ int ring_page);
+static void ne_block_input(struct net_device *dev, int count,
+ struct sk_buff *skb, int ring_offset);
+static void ne_block_output(struct net_device *dev, const int count,
+ const unsigned char *buf, const int start_page);
+
+
+static u32 reg_offset[16];
+
+static int __init init_reg_offset(struct net_device *dev,unsigned long base_addr)
+{
+ struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
+ int i;
+ unsigned char bus_width;
+
+ bus_width = *(volatile unsigned char *)ABWCR;
+ bus_width &= 1 << ((base_addr >> 21) & 7);
+
+ for (i = 0; i < sizeof(reg_offset) / sizeof(u32); i++)
+ if (bus_width == 0)
+ reg_offset[i] = i * 2 + 1;
+ else
+ reg_offset[i] = i;
+
+ ei_local->reg_offset = reg_offset;
+ return 0;
+}
+
+static int __initdata h8300_ne_count = 0;
+#ifdef CONFIG_H8300H_H8MAX
+static unsigned long __initdata h8300_ne_base[] = { 0x800600 };
+static int h8300_ne_irq[] = {EXT_IRQ4};
+#endif
+#ifdef CONFIG_H8300H_AKI3068NET
+static unsigned long __initdata h8300_ne_base[] = { 0x200000 };
+static int h8300_ne_irq[] = {EXT_IRQ5};
+#endif
+
+static inline int init_dev(struct net_device *dev)
+{
+ if (h8300_ne_count < (sizeof(h8300_ne_base) / sizeof(unsigned long))) {
+ dev->base_addr = h8300_ne_base[h8300_ne_count];
+ dev->irq = h8300_ne_irq[h8300_ne_count];
+ h8300_ne_count++;
+ return 0;
+ } else
+ return -ENODEV;
+}
+
+/* Probe for various non-shared-memory ethercards.
+
+ NEx000-clone boards have a Station Address PROM (SAPROM) in the packet
+ buffer memory space. NE2000 clones have 0x57,0x57 in bytes 0x0e,0x0f of
+ the SAPROM, while other supposed NE2000 clones must be detected by their
+ SA prefix.
+
+ Reading the SAPROM from a word-wide card with the 8390 set in byte-wide
+ mode results in doubled values, which can be detected and compensated for.
+
+ The probe is also responsible for initializing the card and filling
+ in the 'dev' and 'ei_status' structures.
+
+ We use the minimum memory size for some ethercard product lines, iff we can't
+ distinguish models. You can increase the packet buffer size by setting
+ PACKETBUF_MEMSIZE. Reported Cabletron packet buffer locations are:
+ E1010 starts at 0x100 and ends at 0x2000.
+ E1010-x starts at 0x100 and ends at 0x8000. ("-x" means "more memory")
+ E2010 starts at 0x100 and ends at 0x4000.
+ E2010-x starts at 0x100 and ends at 0xffff. */
+
+static int __init do_ne_probe(struct net_device *dev)
+{
+ unsigned int base_addr = dev->base_addr;
+
+ SET_MODULE_OWNER(dev);
+
+ /* First check any supplied i/o locations. User knows best. <cough> */
+ if (base_addr > 0x1ff) /* Check a single specified location. */
+ return ne_probe1(dev, base_addr);
+ else if (base_addr != 0) /* Don't probe at all. */
+ return -ENXIO;
+
+ return -ENODEV;
+}
+
+static void cleanup_card(struct net_device *dev)
+{
+ free_irq(dev->irq, dev);
+ release_region(dev->base_addr, NE_IO_EXTENT);
+}
+
+struct net_device * __init ne_probe(int unit)
+{
+ struct net_device *dev = alloc_ei_netdev();
+ int err;
+
+ if (!dev)
+ return ERR_PTR(-ENOMEM);
+
+ if (init_dev(dev))
+ return ERR_PTR(-ENODEV);
+
+ sprintf(dev->name, "eth%d", unit);
+ netdev_boot_setup_check(dev);
+
+ err = init_reg_offset(dev, dev->base_addr);
+ if (err)
+ goto out;
+
+ err = do_ne_probe(dev);
+ if (err)
+ goto out;
+ err = register_netdev(dev);
+ if (err)
+ goto out1;
+ return dev;
+out1:
+ cleanup_card(dev);
+out:
+ free_netdev(dev);
+ return ERR_PTR(err);
+}
+
+static int __init ne_probe1(struct net_device *dev, int ioaddr)
+{
+ int i;
+ unsigned char SA_prom[16];
+ int wordlength = 2;
+ const char *name = NULL;
+ int start_page, stop_page;
+ int reg0, ret;
+ static unsigned version_printed;
+ struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
+ unsigned char bus_width;
+
+ if (!request_region(ioaddr, NE_IO_EXTENT, dev->name))
+ return -EBUSY;
+
+ reg0 = inb_p(ioaddr);
+ if (reg0 == 0xFF) {
+ ret = -ENODEV;
+ goto err_out;
+ }
+
+ /* Do a preliminary verification that we have a 8390. */
+ {
+ int regd;
+ outb_p(E8390_NODMA+E8390_PAGE1+E8390_STOP, ioaddr + E8390_CMD);
+ regd = inb_p(ioaddr + EI_SHIFT(0x0d));
+ outb_p(0xff, ioaddr + EI_SHIFT(0x0d));
+ outb_p(E8390_NODMA+E8390_PAGE0, ioaddr + E8390_CMD);
+ inb_p(ioaddr + EN0_COUNTER0); /* Clear the counter by reading. */
+ if (inb_p(ioaddr + EN0_COUNTER0) != 0) {
+ outb_p(reg0, ioaddr + EI_SHIFT(0));
+ outb_p(regd, ioaddr + EI_SHIFT(0x0d)); /* Restore the old values. */
+ ret = -ENODEV;
+ goto err_out;
+ }
+ }
+
+ if (ei_debug && version_printed++ == 0)
+ printk(KERN_INFO "%s", version1);
+
+ printk(KERN_INFO "NE*000 ethercard probe at %08x:", ioaddr);
+
+ /* Read the 16 bytes of station address PROM.
+ We must first initialize registers, similar to NS8390_init(eifdev, 0).
+ We can't reliably read the SAPROM address without this.
+ (I learned the hard way!). */
+ {
+ struct {unsigned char value, offset; } program_seq[] =
+ {
+ {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/
+ {0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */
+ {0x00, EN0_RCNTLO}, /* Clear the count regs. */
+ {0x00, EN0_RCNTHI},
+ {0x00, EN0_IMR}, /* Mask completion irq. */
+ {0xFF, EN0_ISR},
+ {E8390_RXOFF, EN0_RXCR}, /* 0x20 Set to monitor */
+ {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */
+ {32, EN0_RCNTLO},
+ {0x00, EN0_RCNTHI},
+ {0x00, EN0_RSARLO}, /* DMA starting at 0x0000. */
+ {0x00, EN0_RSARHI},
+ {E8390_RREAD+E8390_START, E8390_CMD},
+ };
+
+ for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++)
+ outb_p(program_seq[i].value, ioaddr + program_seq[i].offset);
+
+ }
+ bus_width = *(volatile unsigned char *)ABWCR;
+ bus_width &= 1 << ((ioaddr >> 21) & 7);
+ ei_status.word16 = (bus_width == 0); /* temporary setting */
+ for(i = 0; i < 16 /*sizeof(SA_prom)*/; i++) {
+ SA_prom[i] = inb_p(ioaddr + NE_DATAPORT);
+ inb_p(ioaddr + NE_DATAPORT); /* dummy read */
+ }
+
+ start_page = NESM_START_PG;
+ stop_page = NESM_STOP_PG;
+
+ if (bus_width)
+ wordlength = 1;
+ else
+ outb_p(0x49, ioaddr + EN0_DCFG);
+
+ /* Set up the rest of the parameters. */
+ name = (wordlength == 2) ? "NE2000" : "NE1000";
+
+ if (! dev->irq) {
+ printk(" failed to detect IRQ line.\n");
+ ret = -EAGAIN;
+ goto err_out;
+ }
+
+ /* Snarf the interrupt now. There's no point in waiting since we cannot
+ share and the board will usually be enabled. */
+ ret = request_irq(dev->irq, ei_interrupt, 0, name, dev);
+ if (ret) {
+ printk (" unable to get IRQ %d (errno=%d).\n", dev->irq, ret);
+ goto err_out;
+ }
+
+ dev->base_addr = ioaddr;
+
+ for(i = 0; i < ETHER_ADDR_LEN; i++) {
+ printk(" %2.2x", SA_prom[i]);
+ dev->dev_addr[i] = SA_prom[i];
+ }
+
+ printk("\n%s: %s found at %#x, using IRQ %d.\n",
+ dev->name, name, ioaddr, dev->irq);
+
+ ei_status.name = name;
+ ei_status.tx_start_page = start_page;
+ ei_status.stop_page = stop_page;
+ ei_status.word16 = (wordlength == 2);
+
+ ei_status.rx_start_page = start_page + TX_PAGES;
+#ifdef PACKETBUF_MEMSIZE
+ /* Allow the packet buffer size to be overridden by know-it-alls. */
+ ei_status.stop_page = ei_status.tx_start_page + PACKETBUF_MEMSIZE;
+#endif
+
+ ei_status.reset_8390 = &ne_reset_8390;
+ ei_status.block_input = &ne_block_input;
+ ei_status.block_output = &ne_block_output;
+ ei_status.get_8390_hdr = &ne_get_8390_hdr;
+ ei_status.priv = 0;
+ dev->open = &ne_open;
+ dev->stop = &ne_close;
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ dev->poll_controller = ei_poll;
+#endif
+ NS8390_init(dev, 0);
+ return 0;
+
+err_out:
+ release_region(ioaddr, NE_IO_EXTENT);
+ return ret;
+}
+
+static int ne_open(struct net_device *dev)
+{
+ ei_open(dev);
+ return 0;
+}
+
+static int ne_close(struct net_device *dev)
+{
+ if (ei_debug > 1)
+ printk(KERN_DEBUG "%s: Shutting down ethercard.\n", dev->name);
+ ei_close(dev);
+ return 0;
+}
+
+/* Hard reset the card. This used to pause for the same period that a
+ 8390 reset command required, but that shouldn't be necessary. */
+
+static void ne_reset_8390(struct net_device *dev)
+{
+ unsigned long reset_start_time = jiffies;
+ struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
+
+ if (ei_debug > 1)
+ printk(KERN_DEBUG "resetting the 8390 t=%ld...", jiffies);
+
+ /* DON'T change these to inb_p/outb_p or reset will fail on clones. */
+ outb(inb(NE_BASE + NE_RESET), NE_BASE + NE_RESET);
+
+ ei_status.txing = 0;
+ ei_status.dmaing = 0;
+
+ /* This check _should_not_ be necessary, omit eventually. */
+ while ((inb_p(NE_BASE+EN0_ISR) & ENISR_RESET) == 0)
+ if (jiffies - reset_start_time > 2*HZ/100) {
+ printk(KERN_WARNING "%s: ne_reset_8390() did not complete.\n", dev->name);
+ break;
+ }
+ outb_p(ENISR_RESET, NE_BASE + EN0_ISR); /* Ack intr. */
+}
+
+/* Grab the 8390 specific header. Similar to the block_input routine, but
+ we don't need to be concerned with ring wrap as the header will be at
+ the start of a page, so we optimize accordingly. */
+
+static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
+{
+ struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
+ /* This *shouldn't* happen. If it does, it's the last thing you'll see */
+
+ if (ei_status.dmaing)
+ {
+ printk(KERN_EMERG "%s: DMAing conflict in ne_get_8390_hdr "
+ "[DMAstat:%d][irqlock:%d].\n",
+ dev->name, ei_status.dmaing, ei_status.irqlock);
+ return;
+ }
+
+ ei_status.dmaing |= 0x01;
+ outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, NE_BASE + NE_CMD);
+ outb_p(sizeof(struct e8390_pkt_hdr), NE_BASE + EN0_RCNTLO);
+ outb_p(0, NE_BASE + EN0_RCNTHI);
+ outb_p(0, NE_BASE + EN0_RSARLO); /* On page boundary */
+ outb_p(ring_page, NE_BASE + EN0_RSARHI);
+ outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD);
+
+ if (ei_status.word16) {
+ int len;
+ unsigned short *p = (unsigned short *)hdr;
+ for (len = sizeof(struct e8390_pkt_hdr)>>1; len > 0; len--)
+ *p++ = inw(NE_BASE + NE_DATAPORT);
+ } else
+ insb(NE_BASE + NE_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr));
+
+ outb_p(ENISR_RDC, NE_BASE + EN0_ISR); /* Ack intr. */
+ ei_status.dmaing &= ~0x01;
+
+ le16_to_cpus(&hdr->count);
+}
+
+/* Block input and output, similar to the Crynwr packet driver. If you
+ are porting to a new ethercard, look at the packet driver source for hints.
+ The NEx000 doesn't share the on-board packet memory -- you have to put
+ the packet out through the "remote DMA" dataport using outb. */
+
+static void ne_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset)
+{
+ struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
+#ifdef NE_SANITY_CHECK
+ int xfer_count = count;
+#endif
+ char *buf = skb->data;
+
+ /* This *shouldn't* happen. If it does, it's the last thing you'll see */
+ if (ei_status.dmaing)
+ {
+ printk(KERN_EMERG "%s: DMAing conflict in ne_block_input "
+ "[DMAstat:%d][irqlock:%d].\n",
+ dev->name, ei_status.dmaing, ei_status.irqlock);
+ return;
+ }
+ ei_status.dmaing |= 0x01;
+ outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, NE_BASE + NE_CMD);
+ outb_p(count & 0xff, NE_BASE + EN0_RCNTLO);
+ outb_p(count >> 8, NE_BASE + EN0_RCNTHI);
+ outb_p(ring_offset & 0xff, NE_BASE + EN0_RSARLO);
+ outb_p(ring_offset >> 8, NE_BASE + EN0_RSARHI);
+ outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD);
+ if (ei_status.word16)
+ {
+ int len;
+ unsigned short *p = (unsigned short *)buf;
+ for (len = count>>1; len > 0; len--)
+ *p++ = inw(NE_BASE + NE_DATAPORT);
+ if (count & 0x01)
+ {
+ buf[count-1] = inb(NE_BASE + NE_DATAPORT);
+#ifdef NE_SANITY_CHECK
+ xfer_count++;
+#endif
+ }
+ } else {
+ insb(NE_BASE + NE_DATAPORT, buf, count);
+ }
+
+#ifdef NE_SANITY_CHECK
+ /* This was for the ALPHA version only, but enough people have
+ been encountering problems so it is still here. If you see
+ this message you either 1) have a slightly incompatible clone
+ or 2) have noise/speed problems with your bus. */
+
+ if (ei_debug > 1)
+ {
+ /* DMA termination address check... */
+ int addr, tries = 20;
+ do {
+ /* DON'T check for 'inb_p(EN0_ISR) & ENISR_RDC' here
+ -- it's broken for Rx on some cards! */
+ int high = inb_p(NE_BASE + EN0_RSARHI);
+ int low = inb_p(NE_BASE + EN0_RSARLO);
+ addr = (high << 8) + low;
+ if (((ring_offset + xfer_count) & 0xff) == low)
+ break;
+ } while (--tries > 0);
+ if (tries <= 0)
+ printk(KERN_WARNING "%s: RX transfer address mismatch,"
+ "%#4.4x (expected) vs. %#4.4x (actual).\n",
+ dev->name, ring_offset + xfer_count, addr);
+ }
+#endif
+ outb_p(ENISR_RDC, NE_BASE + EN0_ISR); /* Ack intr. */
+ ei_status.dmaing &= ~0x01;
+}
+
+static void ne_block_output(struct net_device *dev, int count,
+ const unsigned char *buf, const int start_page)
+{
+ struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
+ unsigned long dma_start;
+#ifdef NE_SANITY_CHECK
+ int retries = 0;
+#endif
+
+ /* Round the count up for word writes. Do we need to do this?
+ What effect will an odd byte count have on the 8390?
+ I should check someday. */
+
+ if (ei_status.word16 && (count & 0x01))
+ count++;
+
+ /* This *shouldn't* happen. If it does, it's the last thing you'll see */
+ if (ei_status.dmaing)
+ {
+ printk(KERN_EMERG "%s: DMAing conflict in ne_block_output."
+ "[DMAstat:%d][irqlock:%d]\n",
+ dev->name, ei_status.dmaing, ei_status.irqlock);
+ return;
+ }
+ ei_status.dmaing |= 0x01;
+ /* We should already be in page 0, but to be safe... */
+ outb_p(E8390_PAGE0+E8390_START+E8390_NODMA, NE_BASE + NE_CMD);
+
+#ifdef NE_SANITY_CHECK
+retry:
+#endif
+
+#ifdef NE8390_RW_BUGFIX
+ /* Handle the read-before-write bug the same way as the
+ Crynwr packet driver -- the NatSemi method doesn't work.
+ Actually this doesn't always work either, but if you have
+ problems with your NEx000 this is better than nothing! */
+
+ outb_p(0x42, NE_BASE + EN0_RCNTLO);
+ outb_p(0x00, NE_BASE + EN0_RCNTHI);
+ outb_p(0x42, NE_BASE + EN0_RSARLO);
+ outb_p(0x00, NE_BASE + EN0_RSARHI);
+ outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD);
+ /* Make certain that the dummy read has occurred. */
+ udelay(6);
+#endif
+
+ outb_p(ENISR_RDC, NE_BASE + EN0_ISR);
+
+ /* Now the normal output. */
+ outb_p(count & 0xff, NE_BASE + EN0_RCNTLO);
+ outb_p(count >> 8, NE_BASE + EN0_RCNTHI);
+ outb_p(0x00, NE_BASE + EN0_RSARLO);
+ outb_p(start_page, NE_BASE + EN0_RSARHI);
+
+ outb_p(E8390_RWRITE+E8390_START, NE_BASE + NE_CMD);
+ if (ei_status.word16) {
+ int len;
+ unsigned short *p = (unsigned short *)buf;
+ for (len = count>>1; len > 0; len--)
+ outw(*p++, NE_BASE + NE_DATAPORT);
+ } else {
+ outsb(NE_BASE + NE_DATAPORT, buf, count);
+ }
+
+ dma_start = jiffies;
+
+#ifdef NE_SANITY_CHECK
+ /* This was for the ALPHA version only, but enough people have
+ been encountering problems so it is still here. */
+
+ if (ei_debug > 1)
+ {
+ /* DMA termination address check... */
+ int addr, tries = 20;
+ do {
+ int high = inb_p(NE_BASE + EN0_RSARHI);
+ int low = inb_p(NE_BASE + EN0_RSARLO);
+ addr = (high << 8) + low;
+ if ((start_page << 8) + count == addr)
+ break;
+ } while (--tries > 0);
+
+ if (tries <= 0)
+ {
+ printk(KERN_WARNING "%s: Tx packet transfer address mismatch,"
+ "%#4.4x (expected) vs. %#4.4x (actual).\n",
+ dev->name, (start_page << 8) + count, addr);
+ if (retries++ == 0)
+ goto retry;
+ }
+ }
+#endif
+
+ while ((inb_p(NE_BASE + EN0_ISR) & ENISR_RDC) == 0)
+ if (jiffies - dma_start > 2*HZ/100) { /* 20ms */
+ printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name);
+ ne_reset_8390(dev);
+ NS8390_init(dev,1);
+ break;
+ }
+
+ outb_p(ENISR_RDC, NE_BASE + EN0_ISR); /* Ack intr. */
+ ei_status.dmaing &= ~0x01;
+ return;
+}
+
+\f
+#ifdef MODULE
+#define MAX_NE_CARDS 1 /* Max number of NE cards per module */
+static struct net_device *dev_ne[MAX_NE_CARDS];
+static int io[MAX_NE_CARDS];
+static int irq[MAX_NE_CARDS];
+static int bad[MAX_NE_CARDS]; /* 0xbad = bad sig or no reset ack */
+
+MODULE_PARM(io, "1-" __MODULE_STRING(MAX_NE_CARDS) "i");
+MODULE_PARM(irq, "1-" __MODULE_STRING(MAX_NE_CARDS) "i");
+MODULE_PARM(bad, "1-" __MODULE_STRING(MAX_NE_CARDS) "i");
+MODULE_PARM_DESC(io, "I/O base address(es)");
+MODULE_PARM_DESC(irq, "IRQ number(s)");
+MODULE_DESCRIPTION("H8/300 NE2000 Ethernet driver");
+MODULE_LICENSE("GPL");
+
+/* This is set up so that no ISA autoprobe takes place. We can't guarantee
+that the ne2k probe is the last 8390 based probe to take place (as it
+is at boot) and so the probe will get confused by any other 8390 cards.
+ISA device autoprobes on a running machine are not recommended anyway. */
+
+int init_module(void)
+{
+ int this_dev, found = 0;
+ int err;
+
+ for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) {
+ struct net_device *dev = alloc_ei_netdev();
+ if (!dev)
+ break;
+ if (io[this_dev]) {
+ dev->irq = irq[this_dev];
+ dev->mem_end = bad[this_dev];
+ dev->base_addr = io[this_dev];
+ } else {
+ dev->base_addr = h8300_ne_base[this_dev];
+ dev->irq = h8300_ne_irq[this_dev];
+ }
+ err = init_reg_offset(dev, dev->base_addr);
+ if (!err) {
+ if (do_ne_probe(dev) == 0) {
+ if (register_netdev(dev) == 0) {
+ dev_ne[found++] = dev;
+ continue;
+ }
+ cleanup_card(dev);
+ }
+ }
+ free_netdev(dev);
+ if (found)
+ break;
+ if (io[this_dev] != 0)
+ printk(KERN_WARNING "ne.c: No NE*000 card found at i/o = %#x\n", dev->base_addr);
+ else
+ printk(KERN_NOTICE "ne.c: You must supply \"io=0xNNN\" value(s) for ISA cards.\n");
+ return -ENXIO;
+ }
+ if (found)
+ return 0;
+ return -ENODEV;
+}
+
+void cleanup_module(void)
+{
+ int this_dev;
+
+ for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) {
+ struct net_device *dev = dev_ne[this_dev];
+ if (dev) {
+ unregister_netdev(dev);
+ cleanup_card(dev);
+ free_netdev(dev);
+ }
+ }
+}
+#endif /* MODULE */
git://git.onelab.eu / linux-2.6.git / blobdiff