*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
+ * the Free Software Foundation; either version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-#include <linux/config.h>
#include <linux/crc32.h>
#include <linux/kernel.h>
#include <linux/version.h>
#include "sky2.h"
#define DRV_NAME "sky2"
-#define DRV_VERSION "1.6.1"
+#define DRV_VERSION "1.10"
#define PFX DRV_NAME " "
/*
* The Yukon II chipset takes 64 bit command blocks (called list elements)
* that are organized into three (receive, transmit, status) different rings
- * similar to Tigon3. A transmit can require several elements;
- * a receive requires one (or two if using 64 bit dma).
+ * similar to Tigon3.
*/
-#define RX_LE_SIZE 512
+#define RX_LE_SIZE 1024
#define RX_LE_BYTES (RX_LE_SIZE*sizeof(struct sky2_rx_le))
-#define RX_MAX_PENDING (RX_LE_SIZE/2 - 2)
+#define RX_MAX_PENDING (RX_LE_SIZE/6 - 2)
#define RX_DEF_PENDING RX_MAX_PENDING
#define RX_SKB_ALIGN 8
+#define RX_BUF_WRITE 16
#define TX_RING_SIZE 512
#define TX_DEF_PENDING (TX_RING_SIZE - 1)
#define STATUS_RING_SIZE 2048 /* 2 ports * (TX + 2*RX) */
#define STATUS_LE_BYTES (STATUS_RING_SIZE*sizeof(struct sky2_status_le))
-#define ETH_JUMBO_MTU 9000
#define TX_WATCHDOG (5 * HZ)
#define NAPI_WEIGHT 64
#define PHY_RETRIES 1000
module_param(debug, int, 0);
MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
-static int copybreak __read_mostly = 256;
+static int copybreak __read_mostly = 128;
module_param(copybreak, int, 0);
MODULE_PARM_DESC(copybreak, "Receive copy threshold");
module_param(disable_msi, int, 0);
MODULE_PARM_DESC(disable_msi, "Disable Message Signaled Interrupt (MSI)");
-static int idle_timeout = 100;
+static int idle_timeout = 0;
module_param(idle_timeout, int, 0);
-MODULE_PARM_DESC(idle_timeout, "Idle timeout workaround for lost interrupts (ms)");
+MODULE_PARM_DESC(idle_timeout, "Watchdog timer for lost interrupts (ms)");
static const struct pci_device_id sky2_id_table[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) },
- { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) },
+ { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) }, /* SK-9Sxx */
+ { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, /* SK-9Exx */
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b00) }, /* DGE-560T */
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4340) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4341) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4342) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4343) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4344) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4345) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4346) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4347) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4350) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4351) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4352) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4360) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) },
- { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4363) },
+ { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4001) }, /* DGE-550SX */
+ { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4B02) }, /* DGE-560SX */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4340) }, /* 88E8021 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4341) }, /* 88E8022 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4342) }, /* 88E8061 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4343) }, /* 88E8062 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4344) }, /* 88E8021 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4345) }, /* 88E8022 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4346) }, /* 88E8061 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4347) }, /* 88E8062 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4350) }, /* 88E8035 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4351) }, /* 88E8036 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4352) }, /* 88E8038 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4353) }, /* 88E8039 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4356) }, /* 88EC033 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4360) }, /* 88E8052 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) }, /* 88E8050 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) }, /* 88E8053 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4363) }, /* 88E8055 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4364) }, /* 88E8056 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4366) }, /* 88EC036 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4367) }, /* 88EC032 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4368) }, /* 88EC034 */
{ 0 }
};
static void sky2_set_power_state(struct sky2_hw *hw, pci_power_t state)
{
u16 power_control;
- u32 reg1;
int vaux;
pr_debug("sky2_set_power_state %d\n", state);
else
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
- /* Turn off phy power saving */
- reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
- reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
-
- /* looks like this XL is back asswards .. */
- if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) {
- reg1 |= PCI_Y2_PHY1_COMA;
- if (hw->ports > 1)
- reg1 |= PCI_Y2_PHY2_COMA;
- }
- sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
- udelay(100);
-
if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
- sky2_write16(hw, B0_CTST, Y2_HW_WOL_ON);
+ u32 reg1;
+
sky2_pci_write32(hw, PCI_DEV_REG3, 0);
reg1 = sky2_pci_read32(hw, PCI_DEV_REG4);
reg1 &= P_ASPM_CONTROL_MSK;
case PCI_D3hot:
case PCI_D3cold:
- /* Turn on phy power saving */
- reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
- if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
- reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
- else
- reg1 |= (PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
- sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
-
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
else
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
-static void sky2_phy_reset(struct sky2_hw *hw, unsigned port)
+static void sky2_gmac_reset(struct sky2_hw *hw, unsigned port)
{
u16 reg;
gma_write16(hw, port, GM_RX_CTRL, reg);
}
+/* flow control to advertise bits */
+static const u16 copper_fc_adv[] = {
+ [FC_NONE] = 0,
+ [FC_TX] = PHY_M_AN_ASP,
+ [FC_RX] = PHY_M_AN_PC,
+ [FC_BOTH] = PHY_M_AN_PC | PHY_M_AN_ASP,
+};
+
+/* flow control to advertise bits when using 1000BaseX */
+static const u16 fiber_fc_adv[] = {
+ [FC_BOTH] = PHY_M_P_BOTH_MD_X,
+ [FC_TX] = PHY_M_P_ASYM_MD_X,
+ [FC_RX] = PHY_M_P_SYM_MD_X,
+ [FC_NONE] = PHY_M_P_NO_PAUSE_X,
+};
+
+/* flow control to GMA disable bits */
+static const u16 gm_fc_disable[] = {
+ [FC_NONE] = GM_GPCR_FC_RX_DIS | GM_GPCR_FC_TX_DIS,
+ [FC_TX] = GM_GPCR_FC_RX_DIS,
+ [FC_RX] = GM_GPCR_FC_TX_DIS,
+ [FC_BOTH] = 0,
+};
+
+
static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
{
struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
- u16 ctrl, ct1000, adv, pg, ledctrl, ledover;
+ u16 ctrl, ct1000, adv, pg, ledctrl, ledover, reg;
if (sky2->autoneg == AUTONEG_ENABLE &&
!(hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)) {
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
}
- ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
- if (sky2->autoneg == AUTONEG_DISABLE)
- ctrl &= ~PHY_CT_ANE;
- else
- ctrl |= PHY_CT_ANE;
-
- ctrl |= PHY_CT_RESET;
- gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
-
- ctrl = 0;
+ ctrl = PHY_CT_RESET;
ct1000 = 0;
adv = PHY_AN_CSMA;
+ reg = 0;
if (sky2->autoneg == AUTONEG_ENABLE) {
if (sky2_is_copper(hw)) {
adv |= PHY_M_AN_10_FD;
if (sky2->advertising & ADVERTISED_10baseT_Half)
adv |= PHY_M_AN_10_HD;
+
+ adv |= copper_fc_adv[sky2->flow_mode];
} else { /* special defines for FIBER (88E1040S only) */
if (sky2->advertising & ADVERTISED_1000baseT_Full)
adv |= PHY_M_AN_1000X_AFD;
if (sky2->advertising & ADVERTISED_1000baseT_Half)
adv |= PHY_M_AN_1000X_AHD;
- }
- /* Set Flow-control capabilities */
- if (sky2->tx_pause && sky2->rx_pause)
- adv |= PHY_AN_PAUSE_CAP; /* symmetric */
- else if (sky2->rx_pause && !sky2->tx_pause)
- adv |= PHY_AN_PAUSE_ASYM | PHY_AN_PAUSE_CAP;
- else if (!sky2->rx_pause && sky2->tx_pause)
- adv |= PHY_AN_PAUSE_ASYM; /* local */
+ adv |= fiber_fc_adv[sky2->flow_mode];
+ }
/* Restart Auto-negotiation */
ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
/* forced speed/duplex settings */
ct1000 = PHY_M_1000C_MSE;
- if (sky2->duplex == DUPLEX_FULL)
- ctrl |= PHY_CT_DUP_MD;
+ /* Disable auto update for duplex flow control and speed */
+ reg |= GM_GPCR_AU_ALL_DIS;
switch (sky2->speed) {
case SPEED_1000:
ctrl |= PHY_CT_SP1000;
+ reg |= GM_GPCR_SPEED_1000;
break;
case SPEED_100:
ctrl |= PHY_CT_SP100;
+ reg |= GM_GPCR_SPEED_100;
break;
}
- ctrl |= PHY_CT_RESET;
+ if (sky2->duplex == DUPLEX_FULL) {
+ reg |= GM_GPCR_DUP_FULL;
+ ctrl |= PHY_CT_DUP_MD;
+ } else if (sky2->speed < SPEED_1000)
+ sky2->flow_mode = FC_NONE;
+
+
+ reg |= gm_fc_disable[sky2->flow_mode];
+
+ /* Forward pause packets to GMAC? */
+ if (sky2->flow_mode & FC_RX)
+ sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
+ else
+ sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
}
+ gma_write16(hw, port, GM_GP_CTRL, reg);
+
if (hw->chip_id != CHIP_ID_YUKON_FE)
gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000);
/* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */
ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL;
/* turn off the Rx LED (LED_RX) */
- ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
+ ledover &= ~PHY_M_LED_MO_RX;
}
- if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == CHIP_REV_YU_EC_A1) {
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
+ hw->chip_rev == CHIP_REV_YU_EC_U_A1) {
/* apply fixes in PHY AFE */
- pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 255);
/* increase differential signal amplitude in 10BASE-T */
gm_phy_write(hw, port, 0x17, 0x2002);
/* set page register to 0 */
- gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0);
} else {
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
/* turn on 100 Mbps LED (LED_LINK100) */
- ledover |= PHY_M_LED_MO_100(MO_LED_ON);
+ ledover |= PHY_M_LED_MO_100;
}
if (ledover)
gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
}
+
/* Enable phy interrupt on auto-negotiation complete (or link up) */
if (sky2->autoneg == AUTONEG_ENABLE)
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
}
+static void sky2_phy_power(struct sky2_hw *hw, unsigned port, int onoff)
+{
+ u32 reg1;
+ static const u32 phy_power[]
+ = { PCI_Y2_PHY1_POWD, PCI_Y2_PHY2_POWD };
+
+ /* looks like this XL is back asswards .. */
+ if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
+ onoff = !onoff;
+
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
+ if (onoff)
+ /* Turn off phy power saving */
+ reg1 &= ~phy_power[port];
+ else
+ reg1 |= phy_power[port];
+
+ sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
+ sky2_pci_read32(hw, PCI_DEV_REG1);
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+ udelay(100);
+}
+
/* Force a renegotiation */
static void sky2_phy_reinit(struct sky2_port *sky2)
{
gm_phy_read(hw, 1, PHY_MARV_INT_MASK) != 0);
}
- if (sky2->autoneg == AUTONEG_DISABLE) {
- reg = gma_read16(hw, port, GM_GP_CTRL);
- reg |= GM_GPCR_AU_ALL_DIS;
- gma_write16(hw, port, GM_GP_CTRL, reg);
- gma_read16(hw, port, GM_GP_CTRL);
-
- switch (sky2->speed) {
- case SPEED_1000:
- reg &= ~GM_GPCR_SPEED_100;
- reg |= GM_GPCR_SPEED_1000;
- break;
- case SPEED_100:
- reg &= ~GM_GPCR_SPEED_1000;
- reg |= GM_GPCR_SPEED_100;
- break;
- case SPEED_10:
- reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
- break;
- }
-
- if (sky2->duplex == DUPLEX_FULL)
- reg |= GM_GPCR_DUP_FULL;
-
- /* turn off pause in 10/100mbps half duplex */
- else if (sky2->speed != SPEED_1000 &&
- hw->chip_id != CHIP_ID_YUKON_EC_U)
- sky2->tx_pause = sky2->rx_pause = 0;
- } else
- reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL;
-
- if (!sky2->tx_pause && !sky2->rx_pause) {
- sky2_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
- reg |=
- GM_GPCR_FC_TX_DIS | GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
- } else if (sky2->tx_pause && !sky2->rx_pause) {
- /* disable Rx flow-control */
- reg |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
- }
-
- gma_write16(hw, port, GM_GP_CTRL, reg);
-
sky2_read16(hw, SK_REG(port, GMAC_IRQ_SRC));
+ /* Enable Transmit FIFO Underrun */
+ sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
+
spin_lock_bh(&sky2->phy_lock);
sky2_phy_init(hw, port);
spin_unlock_bh(&sky2->phy_lock);
/* Flush Rx MAC FIFO on any flow control or error */
sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), GMR_FS_ANY_ERR);
- /* Set threshold to 0xa (64 bytes)
- * ASF disabled so no need to do WA dev #4.30
- */
- sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF);
+ /* Set threshold to 0xa (64 bytes) + 1 to workaround pause bug */
+ sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF+1);
/* Configure Tx MAC FIFO */
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
}
-/* Assign Ram Buffer allocation.
- * start and end are in units of 4k bytes
- * ram registers are in units of 64bit words
- */
-static void sky2_ramset(struct sky2_hw *hw, u16 q, u8 startk, u8 endk)
+/* Assign Ram Buffer allocation to queue */
+static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, u32 space)
{
- u32 start, end;
+ u32 end;
- start = startk * 4096/8;
- end = (endk * 4096/8) - 1;
+ /* convert from K bytes to qwords used for hw register */
+ start *= 1024/8;
+ space *= 1024/8;
+ end = start + space - 1;
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR);
sky2_write32(hw, RB_ADDR(q, RB_START), start);
sky2_write32(hw, RB_ADDR(q, RB_RP), start);
if (q == Q_R1 || q == Q_R2) {
- u32 space = (endk - startk) * 4096/8;
u32 tp = space - space/4;
/* On receive queue's set the thresholds
struct sky2_tx_le *le = sky2->tx_le + sky2->tx_prod;
sky2->tx_prod = RING_NEXT(sky2->tx_prod, TX_RING_SIZE);
+ le->ctrl = 0;
return le;
}
+static inline struct tx_ring_info *tx_le_re(struct sky2_port *sky2,
+ struct sky2_tx_le *le)
+{
+ return sky2->tx_ring + (le - sky2->tx_le);
+}
+
/* Update chip's next pointer */
static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q, u16 idx)
{
+ q = Y2_QADDR(q, PREF_UNIT_PUT_IDX);
wmb();
- sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), idx);
- mmiowb();
+ sky2_write16(hw, q, idx);
+ sky2_read16(hw, q);
}
{
struct sky2_rx_le *le = sky2->rx_le + sky2->rx_put;
sky2->rx_put = RING_NEXT(sky2->rx_put, RX_LE_SIZE);
+ le->ctrl = 0;
return le;
}
return sizeof(a) > sizeof(u32) ? (a >> 16) >> 16 : 0;
}
-/* Build description to hardware about buffer */
-static void sky2_rx_add(struct sky2_port *sky2, dma_addr_t map)
+/* Build description to hardware for one receive segment */
+static void sky2_rx_add(struct sky2_port *sky2, u8 op,
+ dma_addr_t map, unsigned len)
{
struct sky2_rx_le *le;
u32 hi = high32(map);
- u16 len = sky2->rx_bufsize;
if (sky2->rx_addr64 != hi) {
le = sky2_next_rx(sky2);
le->addr = cpu_to_le32(hi);
- le->ctrl = 0;
le->opcode = OP_ADDR64 | HW_OWNER;
sky2->rx_addr64 = high32(map + len);
}
le = sky2_next_rx(sky2);
le->addr = cpu_to_le32((u32) map);
le->length = cpu_to_le16(len);
- le->ctrl = 0;
- le->opcode = OP_PACKET | HW_OWNER;
+ le->opcode = op | HW_OWNER;
+}
+
+/* Build description to hardware for one possibly fragmented skb */
+static void sky2_rx_submit(struct sky2_port *sky2,
+ const struct rx_ring_info *re)
+{
+ int i;
+
+ sky2_rx_add(sky2, OP_PACKET, re->data_addr, sky2->rx_data_size);
+
+ for (i = 0; i < skb_shinfo(re->skb)->nr_frags; i++)
+ sky2_rx_add(sky2, OP_BUFFER, re->frag_addr[i], PAGE_SIZE);
+}
+
+
+static void sky2_rx_map_skb(struct pci_dev *pdev, struct rx_ring_info *re,
+ unsigned size)
+{
+ struct sk_buff *skb = re->skb;
+ int i;
+
+ re->data_addr = pci_map_single(pdev, skb->data, size, PCI_DMA_FROMDEVICE);
+ pci_unmap_len_set(re, data_size, size);
+
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++)
+ re->frag_addr[i] = pci_map_page(pdev,
+ skb_shinfo(skb)->frags[i].page,
+ skb_shinfo(skb)->frags[i].page_offset,
+ skb_shinfo(skb)->frags[i].size,
+ PCI_DMA_FROMDEVICE);
}
+static void sky2_rx_unmap_skb(struct pci_dev *pdev, struct rx_ring_info *re)
+{
+ struct sk_buff *skb = re->skb;
+ int i;
+
+ pci_unmap_single(pdev, re->data_addr, pci_unmap_len(re, data_size),
+ PCI_DMA_FROMDEVICE);
+
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++)
+ pci_unmap_page(pdev, re->frag_addr[i],
+ skb_shinfo(skb)->frags[i].size,
+ PCI_DMA_FROMDEVICE);
+}
/* Tell chip where to start receive checksum.
* Actually has two checksums, but set both same to avoid possible byte
struct sky2_rx_le *le;
le = sky2_next_rx(sky2);
- le->addr = (ETH_HLEN << 16) | ETH_HLEN;
+ le->addr = cpu_to_le32((ETH_HLEN << 16) | ETH_HLEN);
le->ctrl = 0;
le->opcode = OP_TCPSTART | HW_OWNER;
memset(sky2->rx_le, 0, RX_LE_BYTES);
for (i = 0; i < sky2->rx_pending; i++) {
- struct ring_info *re = sky2->rx_ring + i;
+ struct rx_ring_info *re = sky2->rx_ring + i;
if (re->skb) {
- pci_unmap_single(sky2->hw->pdev,
- re->mapaddr, sky2->rx_bufsize,
- PCI_DMA_FROMDEVICE);
+ sky2_rx_unmap_skb(sky2->hw->pdev, re);
kfree_skb(re->skb);
re->skb = NULL;
}
struct sky2_hw *hw = sky2->hw;
u16 port = sky2->port;
- spin_lock_bh(&sky2->tx_lock);
+ netif_tx_lock_bh(dev);
sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), RX_VLAN_STRIP_ON);
sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_VLAN_TAG_ON);
sky2->vlgrp = grp;
- spin_unlock_bh(&sky2->tx_lock);
+ netif_tx_unlock_bh(dev);
}
static void sky2_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid)
struct sky2_hw *hw = sky2->hw;
u16 port = sky2->port;
- spin_lock_bh(&sky2->tx_lock);
+ netif_tx_lock_bh(dev);
sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), RX_VLAN_STRIP_OFF);
sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_VLAN_TAG_OFF);
if (sky2->vlgrp)
sky2->vlgrp->vlan_devices[vid] = NULL;
- spin_unlock_bh(&sky2->tx_lock);
+ netif_tx_unlock_bh(dev);
}
#endif
/*
+ * Allocate an skb for receiving. If the MTU is large enough
+ * make the skb non-linear with a fragment list of pages.
+ *
* It appears the hardware has a bug in the FIFO logic that
* cause it to hang if the FIFO gets overrun and the receive buffer
- * is not aligned. Also dev_alloc_skb() won't align properly if slab
- * debugging is enabled.
+ * is not 64 byte aligned. The buffer returned from netdev_alloc_skb is
+ * aligned except if slab debugging is enabled.
*/
-static inline struct sk_buff *sky2_alloc_skb(unsigned int size, gfp_t gfp_mask)
+static struct sk_buff *sky2_rx_alloc(struct sky2_port *sky2)
{
struct sk_buff *skb;
+ unsigned long p;
+ int i;
- skb = __dev_alloc_skb(size + RX_SKB_ALIGN, gfp_mask);
- if (likely(skb)) {
- unsigned long p = (unsigned long) skb->data;
- skb_reserve(skb, ALIGN(p, RX_SKB_ALIGN) - p);
+ skb = netdev_alloc_skb(sky2->netdev, sky2->rx_data_size + RX_SKB_ALIGN);
+ if (!skb)
+ goto nomem;
+
+ p = (unsigned long) skb->data;
+ skb_reserve(skb, ALIGN(p, RX_SKB_ALIGN) - p);
+
+ for (i = 0; i < sky2->rx_nfrags; i++) {
+ struct page *page = alloc_page(GFP_ATOMIC);
+
+ if (!page)
+ goto free_partial;
+ skb_fill_page_desc(skb, i, page, 0, PAGE_SIZE);
}
return skb;
+free_partial:
+ kfree_skb(skb);
+nomem:
+ return NULL;
}
/*
* Allocate and setup receiver buffer pool.
- * In case of 64 bit dma, there are 2X as many list elements
- * available as ring entries
- * and need to reserve one list element so we don't wrap around.
+ * Normal case this ends up creating one list element for skb
+ * in the receive ring. Worst case if using large MTU and each
+ * allocation falls on a different 64 bit region, that results
+ * in 6 list elements per ring entry.
+ * One element is used for checksum enable/disable, and one
+ * extra to avoid wrap.
*/
static int sky2_rx_start(struct sky2_port *sky2)
{
struct sky2_hw *hw = sky2->hw;
+ struct rx_ring_info *re;
unsigned rxq = rxqaddr[sky2->port];
- int i;
- unsigned thresh;
+ unsigned i, size, space, thresh;
sky2->rx_put = sky2->rx_next = 0;
sky2_qset(hw, rxq);
- if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
- /* MAC Rx RAM Read is controlled by hardware */
+ /* On PCI express lowering the watermark gives better performance */
+ if (pci_find_capability(hw->pdev, PCI_CAP_ID_EXP))
+ sky2_write32(hw, Q_ADDR(rxq, Q_WM), BMU_WM_PEX);
+
+ /* These chips have no ram buffer?
+ * MAC Rx RAM Read is controlled by hardware */
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
+ (hw->chip_rev == CHIP_REV_YU_EC_U_A1
+ || hw->chip_rev == CHIP_REV_YU_EC_U_B0))
sky2_write32(hw, Q_ADDR(rxq, Q_F), F_M_RX_RAM_DIS);
- }
sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
rx_set_checksum(sky2);
+
+ /* Space needed for frame data + headers rounded up */
+ size = ALIGN(sky2->netdev->mtu + ETH_HLEN + VLAN_HLEN, 8)
+ + 8;
+
+ /* Stopping point for hardware truncation */
+ thresh = (size - 8) / sizeof(u32);
+
+ /* Account for overhead of skb - to avoid order > 0 allocation */
+ space = SKB_DATA_ALIGN(size) + NET_SKB_PAD
+ + sizeof(struct skb_shared_info);
+
+ sky2->rx_nfrags = space >> PAGE_SHIFT;
+ BUG_ON(sky2->rx_nfrags > ARRAY_SIZE(re->frag_addr));
+
+ if (sky2->rx_nfrags != 0) {
+ /* Compute residue after pages */
+ space = sky2->rx_nfrags << PAGE_SHIFT;
+
+ if (space < size)
+ size -= space;
+ else
+ size = 0;
+
+ /* Optimize to handle small packets and headers */
+ if (size < copybreak)
+ size = copybreak;
+ if (size < ETH_HLEN)
+ size = ETH_HLEN;
+ }
+ sky2->rx_data_size = size;
+
+ /* Fill Rx ring */
for (i = 0; i < sky2->rx_pending; i++) {
- struct ring_info *re = sky2->rx_ring + i;
+ re = sky2->rx_ring + i;
- re->skb = sky2_alloc_skb(sky2->rx_bufsize, GFP_KERNEL);
+ re->skb = sky2_rx_alloc(sky2);
if (!re->skb)
goto nomem;
- re->mapaddr = pci_map_single(hw->pdev, re->skb->data,
- sky2->rx_bufsize, PCI_DMA_FROMDEVICE);
- sky2_rx_add(sky2, re->mapaddr);
+ sky2_rx_map_skb(hw->pdev, re, sky2->rx_data_size);
+ sky2_rx_submit(sky2, re);
}
-
/*
* The receiver hangs if it receives frames larger than the
* packet buffer. As a workaround, truncate oversize frames, but
* the register is limited to 9 bits, so if you do frames > 2052
* you better get the MTU right!
*/
- thresh = (sky2->rx_bufsize - 8) / sizeof(u32);
if (thresh > 0x1ff)
sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_OFF);
else {
sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_ON);
}
-
/* Tell chip about available buffers */
sky2_write16(hw, Y2_QADDR(rxq, PREF_UNIT_PUT_IDX), sky2->rx_put);
return 0;
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
- u32 ramsize, rxspace, imask;
+ u32 ramsize, imask;
int cap, err = -ENOMEM;
struct net_device *otherdev = hw->dev[sky2->port^1];
goto err_out;
memset(sky2->rx_le, 0, RX_LE_BYTES);
- sky2->rx_ring = kcalloc(sky2->rx_pending, sizeof(struct ring_info),
+ sky2->rx_ring = kcalloc(sky2->rx_pending, sizeof(struct rx_ring_info),
GFP_KERNEL);
if (!sky2->rx_ring)
goto err_out;
+ sky2_phy_power(hw, port, 1);
+
sky2_mac_init(hw, port);
- /* Determine available ram buffer space (in 4K blocks).
- * Note: not sure about the FE setting below yet
- */
- if (hw->chip_id == CHIP_ID_YUKON_FE)
- ramsize = 4;
- else
- ramsize = sky2_read8(hw, B2_E_0);
+ /* Register is number of 4K blocks on internal RAM buffer. */
+ ramsize = sky2_read8(hw, B2_E_0) * 4;
+ printk(KERN_INFO PFX "%s: ram buffer %dK\n", dev->name, ramsize);
- /* Give transmitter one third (rounded up) */
- rxspace = ramsize - (ramsize + 2) / 3;
+ if (ramsize > 0) {
+ u32 rxspace;
- sky2_ramset(hw, rxqaddr[port], 0, rxspace);
- sky2_ramset(hw, txqaddr[port], rxspace, ramsize);
+ if (ramsize < 16)
+ rxspace = ramsize / 2;
+ else
+ rxspace = 8 + (2*(ramsize - 16))/3;
- /* Make sure SyncQ is disabled */
- sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL),
- RB_RST_SET);
+ sky2_ramset(hw, rxqaddr[port], 0, rxspace);
+ sky2_ramset(hw, txqaddr[port], rxspace, ramsize - rxspace);
+
+ /* Make sure SyncQ is disabled */
+ sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL),
+ RB_RST_SET);
+ }
sky2_qset(hw, txqaddr[port]);
/* Set almost empty threshold */
- if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == 1)
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U
+ && hw->chip_rev == CHIP_REV_YU_EC_U_A0)
sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
if (skb_is_gso(skb))
++count;
- if (skb->ip_summed == CHECKSUM_HW)
+ if (skb->ip_summed == CHECKSUM_PARTIAL)
++count;
return count;
* A single packet can generate multiple list elements, and
* the number of ring elements will probably be less than the number
* of list elements used.
- *
- * No BH disabling for tx_lock here (like tg3)
*/
static int sky2_xmit_frame(struct sk_buff *skb, struct net_device *dev)
{
struct sky2_tx_le *le = NULL;
struct tx_ring_info *re;
unsigned i, len;
- int avail;
dma_addr_t mapping;
u32 addr64;
u16 mss;
u8 ctrl;
- /* No BH disabling for tx_lock here. We are running in BH disabled
- * context and TX reclaim runs via poll inside of a software
- * interrupt, and no related locks in IRQ processing.
- */
- if (!spin_trylock(&sky2->tx_lock))
- return NETDEV_TX_LOCKED;
-
- if (unlikely(tx_avail(sky2) < tx_le_req(skb))) {
- /* There is a known but harmless race with lockless tx
- * and netif_stop_queue.
- */
- if (!netif_queue_stopped(dev)) {
- netif_stop_queue(dev);
- if (net_ratelimit())
- printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
- dev->name);
- }
- spin_unlock(&sky2->tx_lock);
-
- return NETDEV_TX_BUSY;
- }
+ if (unlikely(tx_avail(sky2) < tx_le_req(skb)))
+ return NETDEV_TX_BUSY;
if (unlikely(netif_msg_tx_queued(sky2)))
printk(KERN_DEBUG "%s: tx queued, slot %u, len %d\n",
mapping = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE);
addr64 = high32(mapping);
- re = sky2->tx_ring + sky2->tx_prod;
-
/* Send high bits if changed or crosses boundary */
if (addr64 != sky2->tx_addr64 || high32(mapping + len) != sky2->tx_addr64) {
le = get_tx_le(sky2);
- le->tx.addr = cpu_to_le32(addr64);
- le->ctrl = 0;
+ le->addr = cpu_to_le32(addr64);
le->opcode = OP_ADDR64 | HW_OWNER;
sky2->tx_addr64 = high32(mapping + len);
}
/* Check for TCP Segmentation Offload */
mss = skb_shinfo(skb)->gso_size;
if (mss != 0) {
- /* just drop the packet if non-linear expansion fails */
- if (skb_header_cloned(skb) &&
- pskb_expand_head(skb, 0, 0, GFP_ATOMIC)) {
- dev_kfree_skb(skb);
- goto out_unlock;
- }
-
mss += ((skb->h.th->doff - 5) * 4); /* TCP options */
mss += (skb->nh.iph->ihl * 4) + sizeof(struct tcphdr);
mss += ETH_HLEN;
- }
- if (mss != sky2->tx_last_mss) {
- le = get_tx_le(sky2);
- le->tx.tso.size = cpu_to_le16(mss);
- le->tx.tso.rsvd = 0;
- le->opcode = OP_LRGLEN | HW_OWNER;
- le->ctrl = 0;
- sky2->tx_last_mss = mss;
+ if (mss != sky2->tx_last_mss) {
+ le = get_tx_le(sky2);
+ le->addr = cpu_to_le32(mss);
+ le->opcode = OP_LRGLEN | HW_OWNER;
+ sky2->tx_last_mss = mss;
+ }
}
ctrl = 0;
if (sky2->vlgrp && vlan_tx_tag_present(skb)) {
if (!le) {
le = get_tx_le(sky2);
- le->tx.addr = 0;
+ le->addr = 0;
le->opcode = OP_VLAN|HW_OWNER;
- le->ctrl = 0;
} else
le->opcode |= OP_VLAN;
le->length = cpu_to_be16(vlan_tx_tag_get(skb));
#endif
/* Handle TCP checksum offload */
- if (skb->ip_summed == CHECKSUM_HW) {
- u16 hdr = skb->h.raw - skb->data;
- u16 offset = hdr + skb->csum;
+ if (skb->ip_summed == CHECKSUM_PARTIAL) {
+ unsigned offset = skb->h.raw - skb->data;
+ u32 tcpsum;
+
+ tcpsum = offset << 16; /* sum start */
+ tcpsum |= offset + skb->csum_offset; /* sum write */
ctrl = CALSUM | WR_SUM | INIT_SUM | LOCK_SUM;
if (skb->nh.iph->protocol == IPPROTO_UDP)
ctrl |= UDPTCP;
- le = get_tx_le(sky2);
- le->tx.csum.start = cpu_to_le16(hdr);
- le->tx.csum.offset = cpu_to_le16(offset);
- le->length = 0; /* initial checksum value */
- le->ctrl = 1; /* one packet */
- le->opcode = OP_TCPLISW | HW_OWNER;
+ if (tcpsum != sky2->tx_tcpsum) {
+ sky2->tx_tcpsum = tcpsum;
+
+ le = get_tx_le(sky2);
+ le->addr = cpu_to_le32(tcpsum);
+ le->length = 0; /* initial checksum value */
+ le->ctrl = 1; /* one packet */
+ le->opcode = OP_TCPLISW | HW_OWNER;
+ }
}
le = get_tx_le(sky2);
- le->tx.addr = cpu_to_le32((u32) mapping);
+ le->addr = cpu_to_le32((u32) mapping);
le->length = cpu_to_le16(len);
le->ctrl = ctrl;
le->opcode = mss ? (OP_LARGESEND | HW_OWNER) : (OP_PACKET | HW_OWNER);
- /* Record the transmit mapping info */
+ re = tx_le_re(sky2, le);
re->skb = skb;
pci_unmap_addr_set(re, mapaddr, mapping);
+ pci_unmap_len_set(re, maplen, len);
for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
- skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
- struct tx_ring_info *fre;
+ const skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
mapping = pci_map_page(hw->pdev, frag->page, frag->page_offset,
frag->size, PCI_DMA_TODEVICE);
addr64 = high32(mapping);
if (addr64 != sky2->tx_addr64) {
le = get_tx_le(sky2);
- le->tx.addr = cpu_to_le32(addr64);
+ le->addr = cpu_to_le32(addr64);
le->ctrl = 0;
le->opcode = OP_ADDR64 | HW_OWNER;
sky2->tx_addr64 = addr64;
}
le = get_tx_le(sky2);
- le->tx.addr = cpu_to_le32((u32) mapping);
+ le->addr = cpu_to_le32((u32) mapping);
le->length = cpu_to_le16(frag->size);
le->ctrl = ctrl;
le->opcode = OP_BUFFER | HW_OWNER;
- fre = sky2->tx_ring
- + RING_NEXT((re - sky2->tx_ring) + i, TX_RING_SIZE);
- pci_unmap_addr_set(fre, mapaddr, mapping);
+ re = tx_le_re(sky2, le);
+ re->skb = skb;
+ pci_unmap_addr_set(re, mapaddr, mapping);
+ pci_unmap_len_set(re, maplen, frag->size);
}
- re->idx = sky2->tx_prod;
le->ctrl |= EOP;
- avail = tx_avail(sky2);
- if (mss != 0 || avail < TX_MIN_PENDING) {
- le->ctrl |= FRC_STAT;
- if (avail <= MAX_SKB_TX_LE)
- netif_stop_queue(dev);
- }
+ if (tx_avail(sky2) <= MAX_SKB_TX_LE)
+ netif_stop_queue(dev);
sky2_put_idx(hw, txqaddr[sky2->port], sky2->tx_prod);
-out_unlock:
- spin_unlock(&sky2->tx_lock);
-
dev->trans_start = jiffies;
return NETDEV_TX_OK;
}
* Free ring elements from starting at tx_cons until "done"
*
* NB: the hardware will tell us about partial completion of multi-part
- * buffers; these are deferred until completion.
+ * buffers so make sure not to free skb to early.
*/
static void sky2_tx_complete(struct sky2_port *sky2, u16 done)
{
struct net_device *dev = sky2->netdev;
struct pci_dev *pdev = sky2->hw->pdev;
- u16 nxt, put;
- unsigned i;
+ unsigned idx;
BUG_ON(done >= TX_RING_SIZE);
- if (unlikely(netif_msg_tx_done(sky2)))
- printk(KERN_DEBUG "%s: tx done, up to %u\n",
- dev->name, done);
-
- for (put = sky2->tx_cons; put != done; put = nxt) {
- struct tx_ring_info *re = sky2->tx_ring + put;
- struct sk_buff *skb = re->skb;
-
- nxt = re->idx;
- BUG_ON(nxt >= TX_RING_SIZE);
- prefetch(sky2->tx_ring + nxt);
-
- /* Check for partial status */
- if (tx_dist(put, done) < tx_dist(put, nxt))
+ for (idx = sky2->tx_cons; idx != done;
+ idx = RING_NEXT(idx, TX_RING_SIZE)) {
+ struct sky2_tx_le *le = sky2->tx_le + idx;
+ struct tx_ring_info *re = sky2->tx_ring + idx;
+
+ switch(le->opcode & ~HW_OWNER) {
+ case OP_LARGESEND:
+ case OP_PACKET:
+ pci_unmap_single(pdev,
+ pci_unmap_addr(re, mapaddr),
+ pci_unmap_len(re, maplen),
+ PCI_DMA_TODEVICE);
break;
-
- skb = re->skb;
- pci_unmap_single(pdev, pci_unmap_addr(re, mapaddr),
- skb_headlen(skb), PCI_DMA_TODEVICE);
-
- for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
- struct tx_ring_info *fre;
- fre = sky2->tx_ring + RING_NEXT(put + i, TX_RING_SIZE);
- pci_unmap_page(pdev, pci_unmap_addr(fre, mapaddr),
- skb_shinfo(skb)->frags[i].size,
+ case OP_BUFFER:
+ pci_unmap_page(pdev, pci_unmap_addr(re, mapaddr),
+ pci_unmap_len(re, maplen),
PCI_DMA_TODEVICE);
+ break;
}
- dev_kfree_skb(skb);
+ if (le->ctrl & EOP) {
+ if (unlikely(netif_msg_tx_done(sky2)))
+ printk(KERN_DEBUG "%s: tx done %u\n",
+ dev->name, idx);
+ dev_kfree_skb_any(re->skb);
+ }
+
+ le->opcode = 0; /* paranoia */
}
- sky2->tx_cons = put;
- if (tx_avail(sky2) > MAX_SKB_TX_LE)
+ sky2->tx_cons = idx;
+ if (tx_avail(sky2) > MAX_SKB_TX_LE + 4)
netif_wake_queue(dev);
}
/* Cleanup all untransmitted buffers, assume transmitter not running */
-static void sky2_tx_clean(struct sky2_port *sky2)
+static void sky2_tx_clean(struct net_device *dev)
{
- spin_lock_bh(&sky2->tx_lock);
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ netif_tx_lock_bh(dev);
sky2_tx_complete(sky2, sky2->tx_prod);
- spin_unlock_bh(&sky2->tx_lock);
+ netif_tx_unlock_bh(dev);
}
/* Network shutdown */
/* Stop more packets from being queued */
netif_stop_queue(dev);
+ netif_carrier_off(dev);
+
+ /* Disable port IRQ */
+ imask = sky2_read32(hw, B0_IMSK);
+ imask &= ~portirq_msk[port];
+ sky2_write32(hw, B0_IMSK, imask);
+
+ /*
+ * Both ports share the NAPI poll on port 0, so if necessary undo the
+ * the disable that is done in dev_close.
+ */
+ if (sky2->port == 0 && hw->ports > 1)
+ netif_poll_enable(dev);
- sky2_phy_reset(hw, port);
+ sky2_gmac_reset(hw, port);
/* Stop transmitter */
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_STOP);
sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL),
RB_RST_SET | RB_DIS_OP_MD);
+ /* WA for dev. #4.209 */
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U
+ && (hw->chip_rev == CHIP_REV_YU_EC_U_A1 || hw->chip_rev == CHIP_REV_YU_EC_U_B0))
+ sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T),
+ sky2->speed != SPEED_1000 ?
+ TX_STFW_ENA : TX_STFW_DIS);
+
ctrl = gma_read16(hw, port, GM_GP_CTRL);
ctrl &= ~(GM_GPCR_TX_ENA | GM_GPCR_RX_ENA);
gma_write16(hw, port, GM_GP_CTRL, ctrl);
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET);
- /* Disable port IRQ */
- imask = sky2_read32(hw, B0_IMSK);
- imask &= ~portirq_msk[port];
- sky2_write32(hw, B0_IMSK, imask);
+ sky2_phy_power(hw, port, 0);
/* turn off LED's */
sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
synchronize_irq(hw->pdev->irq);
- sky2_tx_clean(sky2);
+ sky2_tx_clean(dev);
sky2_rx_clean(sky2);
pci_free_consistent(hw->pdev, RX_LE_BYTES,
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u16 reg;
-
- /* Enable Transmit FIFO Underrun */
- sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
-
- reg = gma_read16(hw, port, GM_GP_CTRL);
- if (sky2->autoneg == AUTONEG_DISABLE) {
- reg |= GM_GPCR_AU_ALL_DIS;
-
- /* Is write/read necessary? Copied from sky2_mac_init */
- gma_write16(hw, port, GM_GP_CTRL, reg);
- gma_read16(hw, port, GM_GP_CTRL);
-
- switch (sky2->speed) {
- case SPEED_1000:
- reg &= ~GM_GPCR_SPEED_100;
- reg |= GM_GPCR_SPEED_1000;
- break;
- case SPEED_100:
- reg &= ~GM_GPCR_SPEED_1000;
- reg |= GM_GPCR_SPEED_100;
- break;
- case SPEED_10:
- reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
- break;
- }
- } else
- reg &= ~GM_GPCR_AU_ALL_DIS;
-
- if (sky2->duplex == DUPLEX_FULL || sky2->autoneg == AUTONEG_ENABLE)
- reg |= GM_GPCR_DUP_FULL;
+ static const char *fc_name[] = {
+ [FC_NONE] = "none",
+ [FC_TX] = "tx",
+ [FC_RX] = "rx",
+ [FC_BOTH] = "both",
+ };
/* enable Rx/Tx */
+ reg = gma_read16(hw, port, GM_GP_CTRL);
reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA;
gma_write16(hw, port, GM_GP_CTRL, reg);
- gma_read16(hw, port, GM_GP_CTRL);
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
"%s: Link is up at %d Mbps, %s duplex, flow control %s\n",
sky2->netdev->name, sky2->speed,
sky2->duplex == DUPLEX_FULL ? "full" : "half",
- (sky2->tx_pause && sky2->rx_pause) ? "both" :
- sky2->tx_pause ? "tx" : sky2->rx_pause ? "rx" : "none");
+ fc_name[sky2->flow_status]);
}
static void sky2_link_down(struct sky2_port *sky2)
reg = gma_read16(hw, port, GM_GP_CTRL);
reg &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
gma_write16(hw, port, GM_GP_CTRL, reg);
- gma_read16(hw, port, GM_GP_CTRL); /* PCI post */
- if (sky2->rx_pause && !sky2->tx_pause) {
+ if (sky2->flow_status == FC_RX) {
/* restore Asymmetric Pause bit */
gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
gm_phy_read(hw, port, PHY_MARV_AUNE_ADV)
if (netif_msg_link(sky2))
printk(KERN_INFO PFX "%s: Link is down.\n", sky2->netdev->name);
+
sky2_phy_init(hw, port);
}
+static enum flow_control sky2_flow(int rx, int tx)
+{
+ if (rx)
+ return tx ? FC_BOTH : FC_RX;
+ else
+ return tx ? FC_TX : FC_NONE;
+}
+
static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux)
{
struct sky2_hw *hw = sky2->hw;
return -1;
}
- if (hw->chip_id != CHIP_ID_YUKON_FE &&
- gm_phy_read(hw, port, PHY_MARV_1000T_STAT) & PHY_B_1000S_MSF) {
- printk(KERN_ERR PFX "%s: master/slave fault",
- sky2->netdev->name);
- return -1;
- }
-
if (!(aux & PHY_M_PS_SPDUP_RES)) {
printk(KERN_ERR PFX "%s: speed/duplex mismatch",
sky2->netdev->name);
return -1;
}
- sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
-
sky2->speed = sky2_phy_speed(hw, aux);
+ sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
/* Pause bits are offset (9..8) */
if (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)
aux >>= 6;
- sky2->rx_pause = (aux & PHY_M_PS_RX_P_EN) != 0;
- sky2->tx_pause = (aux & PHY_M_PS_TX_P_EN) != 0;
+ sky2->flow_status = sky2_flow(aux & PHY_M_PS_RX_P_EN,
+ aux & PHY_M_PS_TX_P_EN);
+
+ if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000
+ && hw->chip_id != CHIP_ID_YUKON_EC_U)
+ sky2->flow_status = FC_NONE;
- if ((sky2->tx_pause || sky2->rx_pause)
- && !(sky2->speed < SPEED_1000 && sky2->duplex == DUPLEX_HALF))
+ if (aux & PHY_M_PS_RX_P_EN)
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
else
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
struct sky2_port *sky2 = netdev_priv(dev);
u16 istatus, phystat;
+ if (!netif_running(dev))
+ return;
+
spin_lock(&sky2->phy_lock);
istatus = gm_phy_read(hw, port, PHY_MARV_INT_STAT);
phystat = gm_phy_read(hw, port, PHY_MARV_PHY_STAT);
- if (!netif_running(dev))
- goto out;
-
if (netif_msg_intr(sky2))
printk(KERN_INFO PFX "%s: phy interrupt status 0x%x 0x%x\n",
sky2->netdev->name, istatus, phystat);
- if (istatus & PHY_M_IS_AN_COMPL) {
+ if (sky2->autoneg == AUTONEG_ENABLE && (istatus & PHY_M_IS_AN_COMPL)) {
if (sky2_autoneg_done(sky2, phystat) == 0)
sky2_link_up(sky2);
goto out;
/* Transmit timeout is only called if we are running, carries is up
* and tx queue is full (stopped).
+ * Called with netif_tx_lock held.
*/
static void sky2_tx_timeout(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
- unsigned txq = txqaddr[sky2->port];
- u16 report, done;
+ unsigned port = sky2->port;
if (netif_msg_timer(sky2))
printk(KERN_ERR PFX "%s: tx timeout\n", dev->name);
- report = sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX);
- done = sky2_read16(hw, Q_ADDR(txq, Q_DONE));
-
- printk(KERN_DEBUG PFX "%s: transmit ring %u .. %u report=%u done=%u\n",
- dev->name,
- sky2->tx_cons, sky2->tx_prod, report, done);
-
- if (report != done) {
- printk(KERN_INFO PFX "status burst pending (irq moderation?)\n");
-
- sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
- sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
- } else if (report != sky2->tx_cons) {
- printk(KERN_INFO PFX "status report lost?\n");
-
- spin_lock_bh(&sky2->tx_lock);
- sky2_tx_complete(sky2, report);
- spin_unlock_bh(&sky2->tx_lock);
- } else {
- printk(KERN_INFO PFX "hardware hung? flushing\n");
+ /* Get information for bug report :-) */
+ printk(KERN_INFO PFX "%s: transmit ring %u .. %u report=%u done=%u\n",
+ dev->name, sky2->tx_cons, sky2->tx_prod,
+ sky2_read16(hw, port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX),
+ sky2_read16(hw, Q_ADDR(txqaddr[sky2->port], Q_DONE)));
- sky2_write32(hw, Q_ADDR(txq, Q_CSR), BMU_STOP);
- sky2_write32(hw, Y2_QADDR(txq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
+ printk(KERN_INFO PFX "gmac control %#x status %#x\n",
+ gma_read16(hw, port, GM_GP_CTRL), gma_read16(hw, port, GM_GP_STAT));
- sky2_tx_clean(sky2);
-
- sky2_qset(hw, txq);
- sky2_prefetch_init(hw, txq, sky2->tx_le_map, TX_RING_SIZE - 1);
- }
-}
-
-
-/* Want receive buffer size to be multiple of 64 bits
- * and incl room for vlan and truncation
- */
-static inline unsigned sky2_buf_size(int mtu)
-{
- return ALIGN(mtu + ETH_HLEN + VLAN_HLEN, 8) + 8;
+ /* can't restart safely under softirq */
+ schedule_work(&hw->restart_work);
}
static int sky2_change_mtu(struct net_device *dev, int new_mtu)
sky2_rx_clean(sky2);
dev->mtu = new_mtu;
- sky2->rx_bufsize = sky2_buf_size(new_mtu);
+
mode = DATA_BLIND_VAL(DATA_BLIND_DEF) |
GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
return err;
}
+/* For small just reuse existing skb for next receive */
+static struct sk_buff *receive_copy(struct sky2_port *sky2,
+ const struct rx_ring_info *re,
+ unsigned length)
+{
+ struct sk_buff *skb;
+
+ skb = netdev_alloc_skb(sky2->netdev, length + 2);
+ if (likely(skb)) {
+ skb_reserve(skb, 2);
+ pci_dma_sync_single_for_cpu(sky2->hw->pdev, re->data_addr,
+ length, PCI_DMA_FROMDEVICE);
+ memcpy(skb->data, re->skb->data, length);
+ skb->ip_summed = re->skb->ip_summed;
+ skb->csum = re->skb->csum;
+ pci_dma_sync_single_for_device(sky2->hw->pdev, re->data_addr,
+ length, PCI_DMA_FROMDEVICE);
+ re->skb->ip_summed = CHECKSUM_NONE;
+ skb_put(skb, length);
+ }
+ return skb;
+}
+
+/* Adjust length of skb with fragments to match received data */
+static void skb_put_frags(struct sk_buff *skb, unsigned int hdr_space,
+ unsigned int length)
+{
+ int i, num_frags;
+ unsigned int size;
+
+ /* put header into skb */
+ size = min(length, hdr_space);
+ skb->tail += size;
+ skb->len += size;
+ length -= size;
+
+ num_frags = skb_shinfo(skb)->nr_frags;
+ for (i = 0; i < num_frags; i++) {
+ skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+
+ if (length == 0) {
+ /* don't need this page */
+ __free_page(frag->page);
+ --skb_shinfo(skb)->nr_frags;
+ } else {
+ size = min(length, (unsigned) PAGE_SIZE);
+
+ frag->size = size;
+ skb->data_len += size;
+ skb->truesize += size;
+ skb->len += size;
+ length -= size;
+ }
+ }
+}
+
+/* Normal packet - take skb from ring element and put in a new one */
+static struct sk_buff *receive_new(struct sky2_port *sky2,
+ struct rx_ring_info *re,
+ unsigned int length)
+{
+ struct sk_buff *skb, *nskb;
+ unsigned hdr_space = sky2->rx_data_size;
+
+ pr_debug(PFX "receive new length=%d\n", length);
+
+ /* Don't be tricky about reusing pages (yet) */
+ nskb = sky2_rx_alloc(sky2);
+ if (unlikely(!nskb))
+ return NULL;
+
+ skb = re->skb;
+ sky2_rx_unmap_skb(sky2->hw->pdev, re);
+
+ prefetch(skb->data);
+ re->skb = nskb;
+ sky2_rx_map_skb(sky2->hw->pdev, re, hdr_space);
+
+ if (skb_shinfo(skb)->nr_frags)
+ skb_put_frags(skb, hdr_space, length);
+ else
+ skb_put(skb, length);
+ return skb;
+}
+
/*
* Receive one packet.
- * For small packets or errors, just reuse existing skb.
* For larger packets, get new buffer.
*/
-static struct sk_buff *sky2_receive(struct sky2_port *sky2,
+static struct sk_buff *sky2_receive(struct net_device *dev,
u16 length, u32 status)
{
- struct ring_info *re = sky2->rx_ring + sky2->rx_next;
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct rx_ring_info *re = sky2->rx_ring + sky2->rx_next;
struct sk_buff *skb = NULL;
if (unlikely(netif_msg_rx_status(sky2)))
printk(KERN_DEBUG PFX "%s: rx slot %u status 0x%x len %d\n",
- sky2->netdev->name, sky2->rx_next, status, length);
+ dev->name, sky2->rx_next, status, length);
sky2->rx_next = (sky2->rx_next + 1) % sky2->rx_pending;
prefetch(sky2->rx_ring + sky2->rx_next);
if (!(status & GMR_FS_RX_OK))
goto resubmit;
- if (length > sky2->netdev->mtu + ETH_HLEN)
+ if (length > dev->mtu + ETH_HLEN)
goto oversize;
- if (length < copybreak) {
- skb = dev_alloc_skb(length + 2);
- if (!skb)
- goto resubmit;
-
- skb_reserve(skb, 2);
- pci_dma_sync_single_for_cpu(sky2->hw->pdev, re->mapaddr,
- length, PCI_DMA_FROMDEVICE);
- memcpy(skb->data, re->skb->data, length);
- skb->ip_summed = re->skb->ip_summed;
- skb->csum = re->skb->csum;
- pci_dma_sync_single_for_device(sky2->hw->pdev, re->mapaddr,
- length, PCI_DMA_FROMDEVICE);
- } else {
- struct sk_buff *nskb;
-
- nskb = sky2_alloc_skb(sky2->rx_bufsize, GFP_ATOMIC);
- if (!nskb)
- goto resubmit;
-
- skb = re->skb;
- re->skb = nskb;
- pci_unmap_single(sky2->hw->pdev, re->mapaddr,
- sky2->rx_bufsize, PCI_DMA_FROMDEVICE);
- prefetch(skb->data);
-
- re->mapaddr = pci_map_single(sky2->hw->pdev, nskb->data,
- sky2->rx_bufsize, PCI_DMA_FROMDEVICE);
- }
-
- skb_put(skb, length);
+ if (length < copybreak)
+ skb = receive_copy(sky2, re, length);
+ else
+ skb = receive_new(sky2, re, length);
resubmit:
- re->skb->ip_summed = CHECKSUM_NONE;
- sky2_rx_add(sky2, re->mapaddr);
-
- /* Tell receiver about new buffers. */
- sky2_put_idx(sky2->hw, rxqaddr[sky2->port], sky2->rx_put);
+ sky2_rx_submit(sky2, re);
return skb;
error:
++sky2->net_stats.rx_errors;
+ if (status & GMR_FS_RX_FF_OV) {
+ sky2->net_stats.rx_fifo_errors++;
+ goto resubmit;
+ }
if (netif_msg_rx_err(sky2) && net_ratelimit())
printk(KERN_INFO PFX "%s: rx error, status 0x%x length %d\n",
- sky2->netdev->name, status, length);
+ dev->name, status, length);
if (status & (GMR_FS_LONG_ERR | GMR_FS_UN_SIZE))
sky2->net_stats.rx_length_errors++;
sky2->net_stats.rx_frame_errors++;
if (status & GMR_FS_CRC_ERR)
sky2->net_stats.rx_crc_errors++;
- if (status & GMR_FS_RX_FF_OV)
- sky2->net_stats.rx_fifo_errors++;
goto resubmit;
}
struct sky2_port *sky2 = netdev_priv(dev);
if (netif_running(dev)) {
- spin_lock(&sky2->tx_lock);
+ netif_tx_lock(dev);
sky2_tx_complete(sky2, last);
- spin_unlock(&sky2->tx_lock);
+ netif_tx_unlock(dev);
}
}
-/* Is status ring empty or is there more to do? */
-static inline int sky2_more_work(const struct sky2_hw *hw)
-{
- return (hw->st_idx != sky2_read16(hw, STAT_PUT_IDX));
-}
-
/* Process status response ring */
static int sky2_status_intr(struct sky2_hw *hw, int to_do)
{
+ struct sky2_port *sky2;
int work_done = 0;
+ unsigned buf_write[2] = { 0, 0 };
u16 hwidx = sky2_read16(hw, STAT_PUT_IDX);
rmb();
while (hw->st_idx != hwidx) {
struct sky2_status_le *le = hw->st_le + hw->st_idx;
struct net_device *dev;
- struct sky2_port *sky2;
struct sk_buff *skb;
u32 status;
u16 length;
dev = hw->dev[le->link];
sky2 = netdev_priv(dev);
- length = le->length;
- status = le->status;
+ length = le16_to_cpu(le->length);
+ status = le32_to_cpu(le->status);
switch (le->opcode & ~HW_OWNER) {
case OP_RXSTAT:
- skb = sky2_receive(sky2, length, status);
+ skb = sky2_receive(dev, length, status);
if (!skb)
- break;
+ goto force_update;
- skb->dev = dev;
skb->protocol = eth_type_trans(skb, dev);
dev->last_rx = jiffies;
#endif
netif_receive_skb(skb);
+ /* Update receiver after 16 frames */
+ if (++buf_write[le->link] == RX_BUF_WRITE) {
+force_update:
+ sky2_put_idx(hw, rxqaddr[le->link], sky2->rx_put);
+ buf_write[le->link] = 0;
+ }
+
+ /* Stop after net poll weight */
if (++work_done >= to_do)
goto exit_loop;
break;
#endif
case OP_RXCHKS:
skb = sky2->rx_ring[sky2->rx_next].skb;
- skb->ip_summed = CHECKSUM_HW;
- skb->csum = le16_to_cpu(status);
+ skb->ip_summed = CHECKSUM_COMPLETE;
+ skb->csum = status & 0xffff;
break;
case OP_TXINDEXLE:
sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
exit_loop:
+ if (buf_write[0]) {
+ sky2 = netdev_priv(hw->dev[0]);
+ sky2_put_idx(hw, Q_R1, sky2->rx_put);
+ }
+
+ if (buf_write[1]) {
+ sky2 = netdev_priv(hw->dev[1]);
+ sky2_put_idx(hw, Q_R2, sky2->rx_put);
+ }
+
return work_done;
}
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
sky2_pci_write16(hw, PCI_STATUS,
- pci_err | PCI_STATUS_ERROR_BITS);
+ pci_err | PCI_STATUS_ERROR_BITS);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
sky2_descriptor_error(hw, 1, "transmit", Y2_IS_CHK_TXA2);
work_done = sky2_status_intr(hw, work_limit);
- *budget -= work_done;
- dev0->quota -= work_done;
+ if (work_done < work_limit) {
+ netif_rx_complete(dev0);
- if (sky2_more_work(hw))
+ sky2_read32(hw, B0_Y2_SP_LISR);
+ return 0;
+ } else {
+ *budget -= work_done;
+ dev0->quota -= work_done;
return 1;
-
- netif_rx_complete(dev0);
-
- sky2_read32(hw, B0_Y2_SP_LISR);
- return 0;
+ }
}
-static irqreturn_t sky2_intr(int irq, void *dev_id, struct pt_regs *regs)
+static irqreturn_t sky2_intr(int irq, void *dev_id)
{
struct sky2_hw *hw = dev_id;
struct net_device *dev0 = hw->dev[0];
}
-static int __devinit sky2_reset(struct sky2_hw *hw)
+static int sky2_reset(struct sky2_hw *hw)
{
u16 status;
u8 t8;
return -EOPNOTSUPP;
}
+ /* Make sure and enable all clocks */
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U)
+ sky2_pci_write32(hw, PCI_DEV_REG3, 0);
+
hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4;
/* This rev is really old, and requires untested workarounds */
sky2_write32(hw, B0_HWE_IMSK, Y2_HWE_ALL_MASK);
for (i = 0; i < hw->ports; i++)
- sky2_phy_reset(hw, i);
+ sky2_gmac_reset(hw, i);
memset(hw->st_le, 0, STATUS_LE_BYTES);
hw->st_idx = 0;
return 0;
}
+static void sky2_restart(struct work_struct *work)
+{
+ struct sky2_hw *hw = container_of(work, struct sky2_hw, restart_work);
+ struct net_device *dev;
+ int i, err;
+
+ dev_dbg(&hw->pdev->dev, "restarting\n");
+
+ del_timer_sync(&hw->idle_timer);
+
+ rtnl_lock();
+ sky2_write32(hw, B0_IMSK, 0);
+ sky2_read32(hw, B0_IMSK);
+
+ netif_poll_disable(hw->dev[0]);
+
+ for (i = 0; i < hw->ports; i++) {
+ dev = hw->dev[i];
+ if (netif_running(dev))
+ sky2_down(dev);
+ }
+
+ sky2_reset(hw);
+ sky2_write32(hw, B0_IMSK, Y2_IS_BASE);
+ netif_poll_enable(hw->dev[0]);
+
+ for (i = 0; i < hw->ports; i++) {
+ dev = hw->dev[i];
+ if (netif_running(dev)) {
+ err = sky2_up(dev);
+ if (err) {
+ printk(KERN_INFO PFX "%s: could not restart %d\n",
+ dev->name, err);
+ dev_close(dev);
+ }
+ }
+ }
+
+ sky2_idle_start(hw);
+
+ rtnl_unlock();
+}
+
static u32 sky2_supported_modes(const struct sky2_hw *hw)
{
if (sky2_is_copper(hw)) {
{
struct sky2_port *sky2 = netdev_priv(dev);
- if (sky2->autoneg != AUTONEG_ENABLE)
+ if (!netif_running(dev) || sky2->autoneg != AUTONEG_ENABLE)
return -EINVAL;
sky2_phy_reinit(sky2);
return 0;
}
+static void inline sky2_add_filter(u8 filter[8], const u8 *addr)
+{
+ u32 bit;
+
+ bit = ether_crc(ETH_ALEN, addr) & 63;
+ filter[bit >> 3] |= 1 << (bit & 7);
+}
+
static void sky2_set_multicast(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct dev_mc_list *list = dev->mc_list;
u16 reg;
u8 filter[8];
+ int rx_pause;
+ static const u8 pause_mc_addr[ETH_ALEN] = { 0x1, 0x80, 0xc2, 0x0, 0x0, 0x1 };
+ rx_pause = (sky2->flow_status == FC_RX || sky2->flow_status == FC_BOTH);
memset(filter, 0, sizeof(filter));
reg = gma_read16(hw, port, GM_RX_CTRL);
if (dev->flags & IFF_PROMISC) /* promiscuous */
reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
- else if ((dev->flags & IFF_ALLMULTI) || dev->mc_count > 16) /* all multicast */
+ else if (dev->flags & IFF_ALLMULTI)
memset(filter, 0xff, sizeof(filter));
- else if (dev->mc_count == 0) /* no multicast */
+ else if (dev->mc_count == 0 && !rx_pause)
reg &= ~GM_RXCR_MCF_ENA;
else {
int i;
reg |= GM_RXCR_MCF_ENA;
- for (i = 0; list && i < dev->mc_count; i++, list = list->next) {
- u32 bit = ether_crc(ETH_ALEN, list->dmi_addr) & 0x3f;
- filter[bit / 8] |= 1 << (bit % 8);
- }
+ if (rx_pause)
+ sky2_add_filter(filter, pause_mc_addr);
+
+ for (i = 0; list && i < dev->mc_count; i++, list = list->next)
+ sky2_add_filter(filter, list->dmi_addr);
}
gma_write16(hw, port, GM_MC_ADDR_H1,
default:
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
- gm_phy_write(hw, port, PHY_MARV_LED_OVER,
- on ? PHY_M_LED_MO_DUP(MO_LED_ON) |
- PHY_M_LED_MO_10(MO_LED_ON) |
- PHY_M_LED_MO_100(MO_LED_ON) |
- PHY_M_LED_MO_1000(MO_LED_ON) |
- PHY_M_LED_MO_RX(MO_LED_ON)
- : PHY_M_LED_MO_DUP(MO_LED_OFF) |
- PHY_M_LED_MO_10(MO_LED_OFF) |
- PHY_M_LED_MO_100(MO_LED_OFF) |
- PHY_M_LED_MO_1000(MO_LED_OFF) |
- PHY_M_LED_MO_RX(MO_LED_OFF));
-
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ on ? PHY_M_LED_ALL : 0);
}
}
{
struct sky2_port *sky2 = netdev_priv(dev);
- ecmd->tx_pause = sky2->tx_pause;
- ecmd->rx_pause = sky2->rx_pause;
+ switch (sky2->flow_mode) {
+ case FC_NONE:
+ ecmd->tx_pause = ecmd->rx_pause = 0;
+ break;
+ case FC_TX:
+ ecmd->tx_pause = 1, ecmd->rx_pause = 0;
+ break;
+ case FC_RX:
+ ecmd->tx_pause = 0, ecmd->rx_pause = 1;
+ break;
+ case FC_BOTH:
+ ecmd->tx_pause = ecmd->rx_pause = 1;
+ }
+
ecmd->autoneg = sky2->autoneg;
}
struct ethtool_pauseparam *ecmd)
{
struct sky2_port *sky2 = netdev_priv(dev);
- int err = 0;
sky2->autoneg = ecmd->autoneg;
- sky2->tx_pause = ecmd->tx_pause != 0;
- sky2->rx_pause = ecmd->rx_pause != 0;
+ sky2->flow_mode = sky2_flow(ecmd->rx_pause, ecmd->tx_pause);
- sky2_phy_reinit(sky2);
+ if (netif_running(dev))
+ sky2_phy_reinit(sky2);
- return err;
+ return 0;
}
static int sky2_get_coalesce(struct net_device *dev,
regs->len - B3_RI_WTO_R1);
}
-static struct ethtool_ops sky2_ethtool_ops = {
+static const struct ethtool_ops sky2_ethtool_ops = {
.get_settings = sky2_get_settings,
.set_settings = sky2_set_settings,
.get_drvinfo = sky2_get_drvinfo,
dev->poll = sky2_poll;
dev->weight = NAPI_WEIGHT;
#ifdef CONFIG_NET_POLL_CONTROLLER
- dev->poll_controller = sky2_netpoll;
+ /* Network console (only works on port 0)
+ * because netpoll makes assumptions about NAPI
+ */
+ if (port == 0)
+ dev->poll_controller = sky2_netpoll;
#endif
sky2 = netdev_priv(dev);
sky2->hw = hw;
sky2->msg_enable = netif_msg_init(debug, default_msg);
- spin_lock_init(&sky2->tx_lock);
/* Auto speed and flow control */
sky2->autoneg = AUTONEG_ENABLE;
- sky2->tx_pause = 1;
- sky2->rx_pause = 1;
+ sky2->flow_mode = FC_BOTH;
+
sky2->duplex = -1;
sky2->speed = -1;
sky2->advertising = sky2_supported_modes(hw);
spin_lock_init(&sky2->phy_lock);
sky2->tx_pending = TX_DEF_PENDING;
sky2->rx_pending = RX_DEF_PENDING;
- sky2->rx_bufsize = sky2_buf_size(ETH_DATA_LEN);
hw->dev[port] = dev;
sky2->port = port;
- dev->features |= NETIF_F_LLTX;
if (hw->chip_id != CHIP_ID_YUKON_EC_U)
dev->features |= NETIF_F_TSO;
if (highmem)
}
/* Handle software interrupt used during MSI test */
-static irqreturn_t __devinit sky2_test_intr(int irq, void *dev_id,
- struct pt_regs *regs)
+static irqreturn_t __devinit sky2_test_intr(int irq, void *dev_id)
{
struct sky2_hw *hw = dev_id;
u32 status = sky2_read32(hw, B0_Y2_SP_ISRC2);
return IRQ_NONE;
if (status & Y2_IS_IRQ_SW) {
- hw->msi_detected = 1;
+ hw->msi = 1;
wake_up(&hw->msi_wait);
sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ);
}
sky2_write32(hw, B0_IMSK, Y2_IS_IRQ_SW);
- err = request_irq(pdev->irq, sky2_test_intr, SA_SHIRQ, DRV_NAME, hw);
+ err = request_irq(pdev->irq, sky2_test_intr, 0, DRV_NAME, hw);
if (err) {
printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
pci_name(pdev), pdev->irq);
sky2_write8(hw, B0_CTST, CS_ST_SW_IRQ);
sky2_read8(hw, B0_CTST);
- wait_event_timeout(hw->msi_wait, hw->msi_detected, HZ/10);
+ wait_event_timeout(hw->msi_wait, hw->msi, HZ/10);
- if (!hw->msi_detected) {
+ if (!hw->msi) {
/* MSI test failed, go back to INTx mode */
- printk(KERN_WARNING PFX "%s: No interrupt was generated using MSI, "
- "switching to INTx mode. Please report this failure to "
- "the PCI maintainer and include system chipset information.\n",
+ printk(KERN_INFO PFX "%s: No interrupt generated using MSI, "
+ "switching to INTx mode.\n",
pci_name(pdev));
err = -EOPNOTSUPP;
}
sky2_write32(hw, B0_IMSK, 0);
+ sky2_read32(hw, B0_IMSK);
free_irq(pdev->irq, hw);
hw->pm_cap = pm_cap;
#ifdef __BIG_ENDIAN
- /* byte swap descriptors in hardware */
+ /* The sk98lin vendor driver uses hardware byte swapping but
+ * this driver uses software swapping.
+ */
{
u32 reg;
-
reg = sky2_pci_read32(hw, PCI_DEV_REG2);
- reg |= PCI_REV_DESC;
+ reg &= ~PCI_REV_DESC;
sky2_pci_write32(hw, PCI_DEV_REG2, reg);
}
#endif
if (err)
goto err_out_iounmap;
- printk(KERN_INFO PFX "v%s addr 0x%lx irq %d Yukon-%s (0x%x) rev %d\n",
- DRV_VERSION, pci_resource_start(pdev, 0), pdev->irq,
- yukon2_name[hw->chip_id - CHIP_ID_YUKON_XL],
+ printk(KERN_INFO PFX "v%s addr 0x%llx irq %d Yukon-%s (0x%x) rev %d\n",
+ DRV_VERSION, (unsigned long long)pci_resource_start(pdev, 0),
+ pdev->irq, yukon2_name[hw->chip_id - CHIP_ID_YUKON_XL],
hw->chip_id, hw->chip_rev);
dev = sky2_init_netdev(hw, 0, using_dac);
if (!dev)
goto err_out_free_pci;
+ if (!disable_msi && pci_enable_msi(pdev) == 0) {
+ err = sky2_test_msi(hw);
+ if (err == -EOPNOTSUPP)
+ pci_disable_msi(pdev);
+ else if (err)
+ goto err_out_free_netdev;
+ }
+
err = register_netdev(dev);
if (err) {
printk(KERN_ERR PFX "%s: cannot register net device\n",
goto err_out_free_netdev;
}
+ err = request_irq(pdev->irq, sky2_intr, hw->msi ? 0 : IRQF_SHARED,
+ dev->name, hw);
+ if (err) {
+ printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
+ pci_name(pdev), pdev->irq);
+ goto err_out_unregister;
+ }
+ sky2_write32(hw, B0_IMSK, Y2_IS_BASE);
+
sky2_show_addr(dev);
if (hw->ports > 1 && (dev1 = sky2_init_netdev(hw, 1, using_dac))) {
}
}
- if (!disable_msi && pci_enable_msi(pdev) == 0) {
- err = sky2_test_msi(hw);
- if (err == -EOPNOTSUPP)
- pci_disable_msi(pdev);
- else if (err)
- goto err_out_unregister;
- }
-
- err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ, DRV_NAME, hw);
- if (err) {
- printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
- pci_name(pdev), pdev->irq);
- goto err_out_unregister;
- }
-
- sky2_write32(hw, B0_IMSK, Y2_IS_BASE);
-
setup_timer(&hw->idle_timer, sky2_idle, (unsigned long) hw);
+ INIT_WORK(&hw->restart_work, sky2_restart);
+
sky2_idle_start(hw);
pci_set_drvdata(pdev, hw);
return 0;
err_out_unregister:
- pci_disable_msi(pdev);
- if (dev1) {
- unregister_netdev(dev1);
- free_netdev(dev1);
- }
+ if (hw->msi)
+ pci_disable_msi(pdev);
unregister_netdev(dev);
err_out_free_netdev:
free_netdev(dev);
sky2_read8(hw, B0_CTST);
free_irq(pdev->irq, hw);
- pci_disable_msi(pdev);
+ if (hw->msi)
+ pci_disable_msi(pdev);
pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
pci_release_regions(pdev);
pci_disable_device(pdev);
return -EINVAL;
del_timer_sync(&hw->idle_timer);
+ netif_poll_disable(hw->dev[0]);
for (i = 0; i < hw->ports; i++) {
struct net_device *dev = hw->dev[i];
- if (dev) {
- if (!netif_running(dev))
- continue;
-
+ if (netif_running(dev)) {
sky2_down(dev);
netif_device_detach(dev);
- netif_poll_disable(dev);
}
}
pci_restore_state(pdev);
pci_enable_wake(pdev, PCI_D0, 0);
+
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U)
+ sky2_pci_write32(hw, PCI_DEV_REG3, 0);
sky2_set_power_state(hw, PCI_D0);
err = sky2_reset(hw);
for (i = 0; i < hw->ports; i++) {
struct net_device *dev = hw->dev[i];
- if (dev && netif_running(dev)) {
+ if (netif_running(dev)) {
netif_device_attach(dev);
- netif_poll_enable(dev);
err = sky2_up(dev);
if (err) {
}
}
+ netif_poll_enable(hw->dev[0]);
sky2_idle_start(hw);
out:
return err;
module_exit(sky2_cleanup_module);
MODULE_DESCRIPTION("Marvell Yukon 2 Gigabit Ethernet driver");
-MODULE_AUTHOR("Stephen Hemminger <shemminger@osdl.org>");
+MODULE_AUTHOR("Stephen Hemminger <shemminger@linux-foundation.org>");
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);
git://git.onelab.eu / linux-2.6.git / blobdiff