/*
- *
- *
* Copyright (C) 2003 Herbert Valerio Riedel <hvr@gnu.org>
* Copyright (C) 2004 Luis R. Rodriguez <mcgrof@ruslug.rutgers.edu>
* Copyright (C) 2004 Aurelien Alleaume <slts@free.fr>
#if !defined(_ISL_OID_H)
#define _ISL_OID_H
-/*
+/*
* MIB related constant and structure definitions for communicating
* with the device firmware
*/
char data[0];
} __attribute__((packed));
-/*
+/*
* in case everything's ok, the inlined function below will be
* optimized away by the compiler...
*/
static inline void
__bug_on_wrong_struct_sizes(void)
{
- BUG_ON(sizeof (struct obj_ssid) != 34);
- BUG_ON(sizeof (struct obj_key) != 34);
- BUG_ON(sizeof (struct obj_mlme) != 12);
- BUG_ON(sizeof (struct obj_mlmeex) != 14);
- BUG_ON(sizeof (struct obj_buffer) != 8);
- BUG_ON(sizeof (struct obj_bss) != 60);
- BUG_ON(sizeof (struct obj_bsslist) != 4);
- BUG_ON(sizeof (struct obj_frequencies) != 2);
+ BUILD_BUG_ON(sizeof (struct obj_ssid) != 34);
+ BUILD_BUG_ON(sizeof (struct obj_key) != 34);
+ BUILD_BUG_ON(sizeof (struct obj_mlme) != 12);
+ BUILD_BUG_ON(sizeof (struct obj_mlmeex) != 14);
+ BUILD_BUG_ON(sizeof (struct obj_buffer) != 8);
+ BUILD_BUG_ON(sizeof (struct obj_bss) != 60);
+ BUILD_BUG_ON(sizeof (struct obj_bsslist) != 4);
+ BUILD_BUG_ON(sizeof (struct obj_frequencies) != 2);
}
enum dot11_state_t {
/* Prism "Nitro" / Frameburst / "Packet Frame Grouping"
* Value is in microseconds. Represents the # microseconds
- * the firmware will take to group frames before sending out then out
+ * the firmware will take to group frames before sending out then out
* together with a CSMA contention. Without this all frames are
- * sent with a CSMA contention.
- * Bibliography:
+ * sent with a CSMA contention.
+ * Bibliography:
* http://www.hpl.hp.com/personal/Jean_Tourrilhes/Papers/Packet.Frame.Grouping.html
*/
-enum dot11_maxframeburst_t {
+enum dot11_maxframeburst_t {
/* Values for DOT11_OID_MAXFRAMEBURST */
DOT11_MAXFRAMEBURST_OFF = 0, /* Card firmware default */
DOT11_MAXFRAMEBURST_MIXED_SAFE = 650, /* 802.11 a,b,g safe */
/* Support for 802.11 long and short frame preambles.
* Long preamble uses 128-bit sync field, 8-bit CRC
* Short preamble uses 56-bit sync field, 16-bit CRC
- *
+ *
* 802.11a -- not sure, both optionally ?
- * 802.11b supports long and optionally short
+ * 802.11b supports long and optionally short
* 802.11g supports both */
enum dot11_preamblesettings_t {
DOT11_PREAMBLESETTING_LONG = 0,
* Long uses 802.11a slot timing (9 usec ?)
* Short uses 802.11b slot timing (20 use ?) */
enum dot11_slotsettings_t {
- DOT11_SLOTSETTINGS_LONG = 0,
+ DOT11_SLOTSETTINGS_LONG = 0,
/* Allows *only* long 802.11b slot timing */
DOT11_SLOTSETTINGS_SHORT = 1,
/* Allows *only* long 802.11a slot timing */
};
/* All you need to know, ERP is "Extended Rate PHY".
- * An Extended Rate PHY (ERP) STA or AP shall support three different
+ * An Extended Rate PHY (ERP) STA or AP shall support three different
* preamble and header formats:
* Long preamble (refer to above)
* Short preamble (refer to above)
/* (ERP is "Extended Rate PHY") Way to read NONERP is NON-ERP-*
* The key here is DOT11 NON ERP NEVER protects against
* NON ERP STA's. You *don't* want this unless
- * you know what you are doing. It means you will only
+ * you know what you are doing. It means you will only
* get Extended Rate capabilities */
enum dot11_nonerpprotection_t {
DOT11_NONERP_NEVER = 0,
DOT11_NONERP_DYNAMIC = 2
};
-/* Preset OID configuration for 802.11 modes
- * Note: DOT11_OID_CW[MIN|MAX] hold the values of the
+/* Preset OID configuration for 802.11 modes
+ * Note: DOT11_OID_CW[MIN|MAX] hold the values of the
* DCS MIN|MAX backoff used */
enum dot11_profile_t { /* And set/allowed values */
/* Allowed values for DOT11_OID_PROFILES */
DOT11_PROFILE_B_ONLY = 0,
- /* DOT11_OID_RATES: 1, 2, 5.5, 11Mbps
+ /* DOT11_OID_RATES: 1, 2, 5.5, 11Mbps
* DOT11_OID_PREAMBLESETTINGS: DOT11_PREAMBLESETTING_DYNAMIC
* DOT11_OID_CWMIN: 31
* DOT11_OID_NONEPROTECTION: DOT11_NOERP_DYNAMIC
OID_INL_CONFORMANCE_NONE = 0, /* Perform active scanning */
OID_INL_CONFORMANCE_STRICT = 1, /* Strictly adhere to 802.11d */
OID_INL_CONFORMANCE_FLEXIBLE = 2, /* Use passed 802.11d info to
- * determine channel AND/OR just make assumption that active
+ * determine channel AND/OR just make assumption that active
* channels are valid channels */
};