/*
- *
* Copyright (C) 2002 Intersil Americas Inc.
* Copyright (C) 2003 Herbert Valerio Riedel <hvr@gnu.org>
* Copyright (C) 2003 Luis R. Rodriguez <mcgrof@ruslug.rutgers.edu>
*
*/
-#include <linux/version.h>
#include <linux/module.h>
#include <linux/netdevice.h>
******************************************************************************/
irqreturn_t
-islpci_interrupt(int irq, void *config, struct pt_regs *regs)
+islpci_interrupt(int irq, void *config)
{
u32 reg;
islpci_private *priv = config;
islpci_set_state(priv, PRV_STATE_PREBOOT);
/* disable all device interrupts in case they weren't */
- isl38xx_disable_interrupts(priv->device_base);
+ isl38xx_disable_interrupts(priv->device_base);
/* For safety reasons, we may want to ensure that no DMA transfer is
* currently in progress by emptying the TX and RX queues. */
wmb();
/* wait a while for the device to reset */
- set_current_state(TASK_UNINTERRUPTIBLE);
- schedule_timeout(50*HZ/1000);
+ schedule_timeout_uninterruptible(msecs_to_jiffies(50));
return 0;
}
DEFINE_WAIT(wait);
prepare_to_wait(&priv->reset_done, &wait, TASK_UNINTERRUPTIBLE);
-
+
/* now the last step is to reset the interface */
isl38xx_interface_reset(priv->device_base, priv->device_host_address);
islpci_set_state(priv, PRV_STATE_PREINIT);
for(count = 0; count < 2 && result; count++) {
/* The software reset acknowledge needs about 220 msec here.
* Be conservative and wait for up to one second. */
-
- set_current_state(TASK_UNINTERRUPTIBLE);
- remaining = schedule_timeout(HZ);
+
+ remaining = schedule_timeout_uninterruptible(HZ);
if(remaining > 0) {
result = 0;
break;
}
- /* If we're here it's because our IRQ hasn't yet gone through.
+ /* If we're here it's because our IRQ hasn't yet gone through.
* Retry a bit more...
*/
printk(KERN_ERR "%s: no 'reset complete' IRQ seen - retrying\n",
/* Now that the device is 100% up, let's allow
* for the other interrupts --
- * NOTE: this is not *yet* true since we've only allowed the
+ * NOTE: this is not *yet* true since we've only allowed the
* INIT interrupt on the IRQ line. We can perhaps poll
* the IRQ line until we know for sure the reset went through */
isl38xx_enable_common_interrupts(priv->device_base);
}
prism54_acl_init(&priv->acl);
- prism54_wpa_ie_init(priv);
- if (mgt_init(priv))
+ prism54_wpa_bss_ie_init(priv);
+ if (mgt_init(priv))
goto out_free;
return 0;
pci_unmap_single(priv->pdev, buf->pci_addr,
buf->size, PCI_DMA_FROMDEVICE);
buf->pci_addr = 0;
- if (buf->mem)
- kfree(buf->mem);
+ kfree(buf->mem);
buf->size = 0;
buf->mem = NULL;
}
/* Free the acces control list and the WPA list */
prism54_acl_clean(&priv->acl);
- prism54_wpa_ie_clean(priv);
+ prism54_wpa_bss_ie_clean(priv);
mgt_clean(priv);
return 0;
ndev->open = &islpci_open;
ndev->stop = &islpci_close;
ndev->get_stats = &islpci_statistics;
- ndev->get_wireless_stats = &prism54_get_wireless_stats;
ndev->do_ioctl = &prism54_ioctl;
ndev->wireless_handlers =
(struct iw_handler_def *) &prism54_handler_def;
priv->ndev->type = (priv->iw_mode == IW_MODE_MONITOR) ?
priv->monitor_type : ARPHRD_ETHER;
-#if WIRELESS_EXT > 16
/* Add pointers to enable iwspy support. */
priv->wireless_data.spy_data = &priv->spy_data;
ndev->wireless_data = &priv->wireless_data;
-#endif /* WIRELESS_EXT > 16 */
/* save the start and end address of the PCI memory area */
ndev->mem_start = (unsigned long) priv->device_base;
priv->state_off = 1;
/* initialize workqueue's */
- INIT_WORK(&priv->stats_work,
- (void (*)(void *)) prism54_update_stats, priv);
+ INIT_WORK(&priv->stats_work, prism54_update_stats);
priv->stats_timestamp = 0;
- INIT_WORK(&priv->reset_task, islpci_do_reset_and_wake, priv);
+ INIT_WORK(&priv->reset_task, islpci_do_reset_and_wake);
priv->reset_task_pending = 0;
/* allocate various memory areas */