each attached FiberChannel device to sysfs, say Y.
Otherwise, say N.
+config SCSI_ISCSI_ATTRS
+ tristate "iSCSI Transport Attributes"
+ depends on SCSI
+ help
+ If you wish to export transport-specific information about
+ each attached iSCSI device to sysfs, say Y.
+ Otherwise, say N.
+
endmenu
menu "SCSI low-level drivers"
config SCSI_DECNCR
tristate "DEC NCR53C94 Scsi Driver"
- depends on DECSTATION && TC && SCSI
+ depends on MACH_DECSTATION && SCSI && TC
help
Say Y here to support the NCR53C94 SCSI controller chips on IOASIC
based TURBOchannel DECstations and TURBOchannel PMAZ-A cards.
config SCSI_DECSII
tristate "DEC SII Scsi Driver"
- depends on DECSTATION && SCSI
+ depends on MACH_DECSTATION && SCSI && MIPS32
config BLK_DEV_3W_XXXX_RAID
tristate "3ware 5/6/7/8xxx ATA-RAID support"
config SCSI_7000FASST
tristate "7000FASST SCSI support"
- depends on ISA && SCSI
+ depends on ISA && SCSI && ISA_DMA_API
help
This driver supports the Western Digital 7000 SCSI host adapter
family. Some information is in the source:
tristate "ACARD SCSI support"
depends on PCI && SCSI
help
- This driver supports the ACARD 870U/W SCSI host adapter.
-
+ This driver supports the ACARD SCSI host adapter.
+ Support Chip <ATP870 ATP876 ATP880 ATP885>
To compile this driver as a module, choose M here: the
module will be called atp870u.
config SCSI_AHA1542
tristate "Adaptec AHA1542 support"
- depends on ISA && SCSI
+ depends on ISA && SCSI && ISA_DMA_API
---help---
This is support for a SCSI host adapter. It is explained in section
3.4 of the SCSI-HOWTO, available from
module will be called aha1740.
config SCSI_AACRAID
- tristate "Adaptec AACRAID support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && SCSI && PCI
+ tristate "Adaptec AACRAID support"
+ depends on SCSI && PCI
source "drivers/scsi/aic7xxx/Kconfig.aic7xxx"
config SCSI_AIC7XXX_OLD
tristate "Adaptec AIC7xxx support (old driver)"
- depends on SCSI
+ depends on (ISA || EISA || PCI ) && SCSI
help
WARNING This driver is an older aic7xxx driver and is no longer
under active development. Adaptec, Inc. is writing a new driver to
To compile this driver as a module, choose M here: the
module will be called in2000.
-config SCSI_MEGARAID
- tristate "AMI MegaRAID support"
- depends on PCI && SCSI
- help
- This driver supports the AMI MegaRAID 418, 428, 438, 466, 762, 490
- and 467 SCSI host adapters.
-
- To compile this driver as a module, choose M here: the
- module will be called megaraid.
+source "drivers/scsi/megaraid/Kconfig.megaraid"
config SCSI_SATA
bool "Serial ATA (SATA) support"
- depends on SCSI && EXPERIMENTAL
+ depends on SCSI
help
This driver family supports Serial ATA host controllers
and devices.
If unsure, say N.
+config SCSI_SATA_AHCI
+ tristate "AHCI SATA support"
+ depends on SCSI_SATA && PCI
+ help
+ This option enables support for AHCI Serial ATA.
+
+ If unsure, say N.
+
config SCSI_SATA_SVW
- tristate "ServerWorks Frodo / Apple K2 SATA support (EXPERIMENTAL)"
- depends on SCSI_SATA && PCI && EXPERIMENTAL
+ tristate "ServerWorks Frodo / Apple K2 SATA support"
+ depends on SCSI_SATA && PCI
help
This option enables support for Broadcom/Serverworks/Apple K2
SATA support.
If unsure, say N.
+config SCSI_SATA_QSTOR
+ tristate "Pacific Digital SATA QStor support"
+ depends on SCSI_SATA && PCI
+ help
+ This option enables support for Pacific Digital Serial ATA QStor.
+
+ If unsure, say N.
+
config SCSI_SATA_SX4
tristate "Promise SATA SX4 support"
depends on SCSI_SATA && PCI && EXPERIMENTAL
config SCSI_SATA_SIS
tristate "SiS 964/180 SATA support"
- depends on SCSI_SATA && PCI
+ depends on SCSI_SATA && PCI && EXPERIMENTAL
help
This option enables support for SiS Serial ATA 964/180.
If unsure, say N.
+config SCSI_SATA_ULI
+ tristate "ULi Electronics SATA support"
+ depends on SCSI_SATA && PCI && EXPERIMENTAL
+ help
+ This option enables support for ULi Electronics SATA.
+
+ If unsure, say N.
+
config SCSI_SATA_VIA
tristate "VIA SATA support"
- depends on SCSI_SATA && PCI && EXPERIMENTAL
+ depends on SCSI_SATA && PCI
help
This option enables support for VIA Serial ATA.
config SCSI_SATA_VITESSE
tristate "VITESSE VSC-7174 SATA support"
- depends on SCSI_SATA && PCI && EXPERIMENTAL
+ depends on SCSI_SATA && PCI
help
This option enables support for Vitesse VSC7174 Serial ATA.
config SCSI_BUSLOGIC
tristate "BusLogic SCSI support"
- depends on (PCI || ISA || MCA) && SCSI && (BROKEN || !SPARC64)
+ depends on (PCI || ISA || MCA) && SCSI && ISA_DMA_API
---help---
This is support for BusLogic MultiMaster and FlashPoint SCSI Host
Adapters. Consult the SCSI-HOWTO, available from
config SCSI_EATA
tristate "EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant boards) support"
- depends on (ISA || EISA || PCI) && SCSI && (BROKEN || !SPARC64)
+ depends on (ISA || EISA || PCI) && SCSI && ISA_DMA_API
---help---
This driver supports all EATA/DMA-compliant SCSI host adapters. DPT
ISA and all EISA I/O addresses are probed looking for the "EATA"
config SCSI_EATA_PIO
tristate "EATA-PIO (old DPT PM2001, PM2012A) support"
- depends on SCSI
+ depends on (ISA || EISA || PCI) && SCSI && BROKEN
---help---
This driver supports all EATA-PIO protocol compliant SCSI Host
Adapters like the DPT PM2001 and the PM2012A. EATA-DMA compliant
config SCSI_GDTH
tristate "Intel/ICP (former GDT SCSI Disk Array) RAID Controller support"
- depends on (ISA || EISA || PCI) && SCSI && (BROKEN || !SPARC64)
+ depends on (ISA || EISA || PCI) && SCSI && ISA_DMA_API
---help---
Formerly called GDT SCSI Disk Array Controller Support.
See <http://www.developer.ibm.com/welcome/netfinity/serveraid.html>
for more information. If this driver does not work correctly
without modification please contact the author by email at
- ipslinux@adaptec.com.
+ <ipslinux@adaptec.com>.
To compile this driver as a module, choose M here: the
module will be called ips.
+config SCSI_IBMVSCSI
+ tristate "IBM Virtual SCSI support"
+ depends on PPC_PSERIES || PPC_ISERIES
+ help
+ This is the IBM POWER Virtual SCSI Client
+
+ To compile this driver as a module, choose M here: the
+ module will be called ibmvscsic.
+
config SCSI_INITIO
tristate "Initio 9100U(W) support"
- depends on PCI && SCSI && BROKEN
+ depends on PCI && SCSI
help
This is support for the Initio 91XXU(W) SCSI host adapter. Please
read the SCSI-HOWTO, available from
Unless you have an NCR manufactured machine, the chances are that
you do not have this SCSI card, so say N.
-config 53C700_IO_MAPPED
- bool
- depends on SCSI_NCR_D700
- default y
-
config SCSI_LASI700
tristate "HP Lasi SCSI support for 53c700/710"
depends on GSC && SCSI
many PA-RISC workstations & servers. If you do not know whether you
have a Lasi chip, it is safe to say "Y" here.
-config 53C700_MEM_MAPPED
- bool
- depends on SCSI_LASI700
- default y
-
config 53C700_LE_ON_BE
bool
depends on SCSI_LASI700
config SCSI_ZALON
tristate "Zalon SCSI support"
depends on GSC && SCSI
+ select SCSI_SPI_ATTRS
help
The Zalon is a GSC/HSC bus interface chip that sits between the
PA-RISC processor and the NCR 53c720 SCSI controller on C100,
config SCSI_NCR_Q720
tristate "NCR Quad 720 MCA SCSI support"
depends on MCA && SCSI
+ select SCSI_SPI_ATTRS
help
This is a driver for the MicroChannel Quad 720 card produced by
NCR and commonly used in 345x/35xx/4100 class machines. It always
module will be called qlogicfas.
config SCSI_QLOGIC_ISP
- tristate "Qlogic ISP SCSI support"
- depends on PCI && SCSI
+ tristate "Qlogic ISP SCSI support (old driver)"
+ depends on PCI && SCSI && BROKEN
---help---
This driver works for all QLogic PCI SCSI host adapters (IQ-PCI,
IQ-PCI-10, IQ_PCI-D) except for the PCI-basic card. (This latter
To compile this driver as a module, choose M here: the
module will be called qlogicisp.
+ These days the hardware is also supported by the more modern qla1280
+ driver. In doubt use that one instead of qlogicisp.
+
config SCSI_QLOGIC_FC
tristate "Qlogic ISP FC SCSI support"
depends on PCI && SCSI
qlogicfc driver. This is required on some platforms.
config SCSI_QLOGIC_1280
- tristate "Qlogic QLA 1280 SCSI support"
+ tristate "Qlogic QLA 1240/1x80/1x160 SCSI support"
depends on PCI && SCSI
help
- Say Y if you have a QLogic ISP1x80/1x160 SCSI host adapter.
+ Say Y if you have a QLogic ISP1240/1x80/1x160 SCSI host adapter.
To compile this driver as a module, choose M here: the
module will be called qla1280.
+config SCSI_QLOGIC_1280_1040
+ bool "Qlogic QLA 1020/1040 SCSI support"
+ depends on SCSI_QLOGIC_1280 && SCSI_QLOGIC_ISP!=y
+ help
+ Say Y here if you have a QLogic ISP1020/1040 SCSI host adapter and
+ do not want to use the old driver. This option enables support in
+ the qla1280 driver for those host adapters.
+
config SCSI_QLOGICPTI
tristate "PTI Qlogic, ISP Driver"
depends on SBUS && SCSI
source "drivers/scsi/qla2xxx/Kconfig"
+config SCSI_LPFC
+ tristate "Emulex LightPulse Fibre Channel Support"
+ depends on PCI && SCSI
+ select SCSI_FC_ATTRS
+ help
+ This lpfc driver supports the Emulex LightPulse
+ Family of Fibre Channel PCI host adapters.
+
config SCSI_SEAGATE
tristate "Seagate ST-02 and Future Domain TMC-8xx SCSI support"
depends on X86 && ISA && SCSI && BROKEN
config SCSI_U14_34F
tristate "UltraStor 14F/34F support"
- depends on ISA && SCSI
+ depends on ISA && SCSI && ISA_DMA_API
---help---
This is support for the UltraStor 14F and 34F SCSI-2 host adapters.
The source at <file:drivers/scsi/u14-34f.c> contains some
host adapter with one dummy SCSI disk. Each dummy disk uses kernel
RAM as storage (i.e. it is a ramdisk). To save space when multiple
dummy disks are simulated, they share the same kernel RAM for
- their storage. See http://www.torque.net/sg/sdebug.html for more
+ their storage. See <http://www.torque.net/sg/sdebug.html> for more
information. This driver is primarily of use to those testing the
SCSI and block subsystems. If unsure, say N.
config SCSI_MESH
tristate "MESH (Power Mac internal SCSI) support"
- depends on PPC_PMAC && SCSI
+ depends on PPC32 && PPC_PMAC && SCSI
help
Many Power Macintoshes and clones have a MESH (Macintosh Enhanced
SCSI Hardware) SCSI bus adaptor (the 7200 doesn't, but all of the
config SCSI_MAC53C94
tristate "53C94 (Power Mac external SCSI) support"
- depends on PPC_PMAC && SCSI
+ depends on PPC32 && PPC_PMAC && SCSI
help
On Power Macintoshes (and clones) with two SCSI buses, the external
SCSI bus is usually controlled by a 53C94 SCSI bus adaptor. Older
config JAZZ_ESP
bool "MIPS JAZZ FAS216 SCSI support"
- depends on MIPS_JAZZ && SCSI
+ depends on MACH_JAZZ && SCSI
help
This is the driver for the onboard SCSI host adapter of MIPS Magnum
4000, Acer PICA, Olivetti M700-10 and a few other identical OEM
config SUN3_SCSI
tristate "Sun3 NCR5380 SCSI"
- depends on SUN3 && SCSI
+ depends on SUN3 && SCSI && BROKEN
help
This option will enable support for the OBIO (onboard io) NCR5380
SCSI controller found in the Sun 3/50 and 3/60, as well as for
config ZFCP
tristate "FCP host bus adapter driver for IBM eServer zSeries"
- depends on ARCH_S390 && SCSI
+ depends on ARCH_S390 && QDIO && SCSI
select SCSI_FC_ATTRS
help
If you want to access SCSI devices attached to your IBM eServer
This driver is also available as a module. This module will be
called zfcp. If you want to compile it as a module, say M here
- and read Documentation/modules.txt.
+ and read <file:Documentation/modules.txt>.
endmenu