/*
-
- ata_piix.c - Intel PATA/SATA controllers
-
- Maintained by: Jeff Garzik <jgarzik@pobox.com>
- Please ALWAYS copy linux-ide@vger.kernel.org
- on emails.
-
-
- Copyright 2003-2004 Red Hat Inc
- Copyright 2003-2004 Jeff Garzik
-
-
- Copyright header from piix.c:
-
- Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
- Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
- Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
-
- May be copied or modified under the terms of the GNU General Public License
-
+ * ata_piix.c - Intel PATA/SATA controllers
+ *
+ * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Please ALWAYS copy linux-ide@vger.kernel.org
+ * on emails.
+ *
+ *
+ * Copyright 2003-2005 Red Hat Inc
+ * Copyright 2003-2005 Jeff Garzik
+ *
+ *
+ * Copyright header from piix.c:
+ *
+ * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
+ * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING. If not, write to
+ * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *
+ * libata documentation is available via 'make {ps|pdf}docs',
+ * as Documentation/DocBook/libata.*
+ *
+ * Hardware documentation available at http://developer.intel.com/
+ *
+ * Documentation
+ * Publically available from Intel web site. Errata documentation
+ * is also publically available. As an aide to anyone hacking on this
+ * driver the list of errata that are relevant is below.going back to
+ * PIIX4. Older device documentation is now a bit tricky to find.
+ *
+ * The chipsets all follow very much the same design. The orginal Triton
+ * series chipsets do _not_ support independant device timings, but this
+ * is fixed in Triton II. With the odd mobile exception the chips then
+ * change little except in gaining more modes until SATA arrives. This
+ * driver supports only the chips with independant timing (that is those
+ * with SITRE and the 0x44 timing register). See pata_oldpiix and pata_mpiix
+ * for the early chip drivers.
+ *
+ * Errata of note:
+ *
+ * Unfixable
+ * PIIX4 errata #9 - Only on ultra obscure hw
+ * ICH3 errata #13 - Not observed to affect real hw
+ * by Intel
+ *
+ * Things we must deal with
+ * PIIX4 errata #10 - BM IDE hang with non UDMA
+ * (must stop/start dma to recover)
+ * 440MX errata #15 - As PIIX4 errata #10
+ * PIIX4 errata #15 - Must not read control registers
+ * during a PIO transfer
+ * 440MX errata #13 - As PIIX4 errata #15
+ * ICH2 errata #21 - DMA mode 0 doesn't work right
+ * ICH0/1 errata #55 - As ICH2 errata #21
+ * ICH2 spec c #9 - Extra operations needed to handle
+ * drive hotswap [NOT YET SUPPORTED]
+ * ICH2 spec c #20 - IDE PRD must not cross a 64K boundary
+ * and must be dword aligned
+ * ICH2 spec c #24 - UDMA mode 4,5 t85/86 should be 6ns not 3.3
+ *
+ * Should have been BIOS fixed:
+ * 450NX: errata #19 - DMA hangs on old 450NX
+ * 450NX: errata #20 - DMA hangs on old 450NX
+ * 450NX: errata #25 - Corruption with DMA on old 450NX
+ * ICH3 errata #15 - IDE deadlock under high load
+ * (BIOS must set dev 31 fn 0 bit 23)
+ * ICH3 errata #18 - Don't use native mode
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
-#include "scsi.h"
+#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "ata_piix"
-#define DRV_VERSION "1.02"
+#define DRV_VERSION "2.00"
enum {
PIIX_IOCFG = 0x54, /* IDE I/O configuration register */
ICH5_PMR = 0x90, /* port mapping register */
ICH5_PCS = 0x92, /* port control and status */
+ PIIX_SCC = 0x0A, /* sub-class code register */
- PIIX_FLAG_CHECKINTR = (1 << 29), /* make sure PCI INTx enabled */
- PIIX_FLAG_COMBINED = (1 << 30), /* combined mode possible */
+ PIIX_FLAG_IGNORE_PCS = (1 << 25), /* ignore PCS present bits */
+ PIIX_FLAG_SCR = (1 << 26), /* SCR available */
+ PIIX_FLAG_AHCI = (1 << 27), /* AHCI possible */
+ PIIX_FLAG_CHECKINTR = (1 << 28), /* make sure PCI INTx enabled */
/* combined mode. if set, PATA is channel 0.
* if clear, PATA is channel 1.
*/
- PIIX_COMB_PATA_P0 = (1 << 1),
- PIIX_COMB = (1 << 2), /* combined mode enabled? */
-
- PIIX_PORT_PRESENT = (1 << 0),
- PIIX_PORT_ENABLED = (1 << 4),
+ PIIX_PORT_ENABLED = (1 << 0),
+ PIIX_PORT_PRESENT = (1 << 4),
PIIX_80C_PRI = (1 << 5) | (1 << 4),
PIIX_80C_SEC = (1 << 7) | (1 << 6),
- ich5_pata = 0,
- ich5_sata = 1,
- piix4_pata = 2,
- ich6_sata = 3,
+ /* controller IDs */
+ piix4_pata = 0,
+ ich5_pata = 1,
+ ich5_sata = 2,
+ esb_sata = 3,
+ ich6_sata = 4,
+ ich6_sata_ahci = 5,
+ ich6m_sata_ahci = 6,
+ ich7m_sata_ahci = 7,
+ ich8_sata_ahci = 8,
+
+ /* constants for mapping table */
+ P0 = 0, /* port 0 */
+ P1 = 1, /* port 1 */
+ P2 = 2, /* port 2 */
+ P3 = 3, /* port 3 */
+ IDE = -1, /* IDE */
+ NA = -2, /* not avaliable */
+ RV = -3, /* reserved */
+
+ PIIX_AHCI_DEVICE = 6,
+};
+
+struct piix_map_db {
+ const u32 mask;
+ const u16 port_enable;
+ const int present_shift;
+ const int map[][4];
+};
+
+struct piix_host_priv {
+ const int *map;
+ const struct piix_map_db *map_db;
};
static int piix_init_one (struct pci_dev *pdev,
const struct pci_device_id *ent);
-
-static void piix_pata_phy_reset(struct ata_port *ap);
-static void piix_sata_phy_reset(struct ata_port *ap);
-static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev,
- unsigned int pio);
-static void piix_set_udmamode (struct ata_port *ap, struct ata_device *adev,
- unsigned int udma);
+static void piix_host_stop(struct ata_host_set *host_set);
+static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
+static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
+static void piix_pata_error_handler(struct ata_port *ap);
+static void piix_sata_error_handler(struct ata_port *ap);
static unsigned int in_module_init = 1;
-static struct pci_device_id piix_pci_tbl[] = {
+static const struct pci_device_id piix_pci_tbl[] = {
#ifdef ATA_ENABLE_PATA
{ 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix4_pata },
{ 0x8086, 0x24db, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
{ 0x8086, 0x25a2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
+ { 0x8086, 0x27df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
#endif
/* NOTE: The following PCI ids must be kept in sync with the
* list in drivers/pci/quirks.c.
*/
+ /* 82801EB (ICH5) */
{ 0x8086, 0x24d1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
+ /* 82801EB (ICH5) */
{ 0x8086, 0x24df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
- { 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
- { 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
-
- /* ICH6 operates in two modes, "looks-like-ICH5" mode,
- * and enhanced mode, with queueing and other fancy stuff.
- * This is distinguished by PCI class code.
- */
+ /* 6300ESB (ICH5 variant with broken PCS present bits) */
+ { 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata },
+ /* 6300ESB pretending RAID */
+ { 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata },
+ /* 82801FB/FW (ICH6/ICH6W) */
{ 0x8086, 0x2651, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
- { 0x8086, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
+ /* 82801FR/FRW (ICH6R/ICH6RW) */
+ { 0x8086, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ /* 82801FBM ICH6M (ICH6R with only port 0 and 2 implemented) */
+ { 0x8086, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci },
+ /* 82801GB/GR/GH (ICH7, identical to ICH6) */
+ { 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ /* 2801GBM/GHM (ICH7M, identical to ICH6M) */
+ { 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich7m_sata_ahci },
+ /* Enterprise Southbridge 2 (where's the datasheet?) */
+ { 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ /* SATA Controller 1 IDE (ICH8, no datasheet yet) */
+ { 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller 2 IDE (ICH8, ditto) */
+ { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* Mobile SATA Controller IDE (ICH8M, ditto) */
+ { 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
{ } /* terminate list */
};
.id_table = piix_pci_tbl,
.probe = piix_init_one,
.remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
-static Scsi_Host_Template piix_sht = {
+static struct scsi_host_template piix_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
- .eh_strategy_handler = ata_scsi_error,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
- .max_sectors = ATA_MAX_SECTORS,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
-static struct ata_port_operations piix_pata_ops = {
+static const struct ata_port_operations piix_pata_ops = {
.port_disable = ata_port_disable,
.set_piomode = piix_set_piomode,
- .set_udmamode = piix_set_udmamode,
-
- .tf_load = ata_tf_load_pio,
- .tf_read = ata_tf_read_pio,
- .check_status = ata_check_status_pio,
- .exec_command = ata_exec_command_pio,
-
- .phy_reset = piix_pata_phy_reset,
-
- .bmdma_setup = ata_bmdma_setup_pio,
- .bmdma_start = ata_bmdma_start_pio,
+ .set_dmamode = piix_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_pio_data_xfer,
- .eng_timeout = ata_eng_timeout,
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = piix_pata_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
+ .host_stop = piix_host_stop,
};
-static struct ata_port_operations piix_sata_ops = {
+static const struct ata_port_operations piix_sata_ops = {
.port_disable = ata_port_disable,
- .set_piomode = piix_set_piomode,
- .set_udmamode = piix_set_udmamode,
-
- .tf_load = ata_tf_load_pio,
- .tf_read = ata_tf_read_pio,
- .check_status = ata_check_status_pio,
- .exec_command = ata_exec_command_pio,
- .phy_reset = piix_sata_phy_reset,
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
- .bmdma_setup = ata_bmdma_setup_pio,
- .bmdma_start = ata_bmdma_start_pio,
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_pio_data_xfer,
- .eng_timeout = ata_eng_timeout,
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = piix_sata_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
+ .host_stop = piix_host_stop,
+};
+
+static const struct piix_map_db ich5_map_db = {
+ .mask = 0x7,
+ .port_enable = 0x3,
+ .present_shift = 4,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, NA, P1, NA }, /* 000b */
+ { P1, NA, P0, NA }, /* 001b */
+ { RV, RV, RV, RV },
+ { RV, RV, RV, RV },
+ { P0, P1, IDE, IDE }, /* 100b */
+ { P1, P0, IDE, IDE }, /* 101b */
+ { IDE, IDE, P0, P1 }, /* 110b */
+ { IDE, IDE, P1, P0 }, /* 111b */
+ },
+};
+
+static const struct piix_map_db ich6_map_db = {
+ .mask = 0x3,
+ .port_enable = 0xf,
+ .present_shift = 4,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, P2, P1, P3 }, /* 00b */
+ { IDE, IDE, P1, P3 }, /* 01b */
+ { P0, P2, IDE, IDE }, /* 10b */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db ich6m_map_db = {
+ .mask = 0x3,
+ .port_enable = 0x5,
+ .present_shift = 4,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, P2, RV, RV }, /* 00b */
+ { RV, RV, RV, RV },
+ { P0, P2, IDE, IDE }, /* 10b */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db ich7m_map_db = {
+ .mask = 0x3,
+ .port_enable = 0x5,
+ .present_shift = 4,
+
+ /* Map 01b isn't specified in the doc but some notebooks use
+ * it anyway. ATM, the only case spotted carries subsystem ID
+ * 1025:0107. This is the only difference from ich6m.
+ */
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, P2, RV, RV }, /* 00b */
+ { IDE, IDE, P1, P3 }, /* 01b */
+ { P0, P2, IDE, IDE }, /* 10b */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db ich8_map_db = {
+ .mask = 0x3,
+ .port_enable = 0x3,
+ .present_shift = 8,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, NA, P1, NA }, /* 00b (hardwired) */
+ { RV, RV, RV, RV },
+ { RV, RV, RV, RV }, /* 10b (never) */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db *piix_map_db_table[] = {
+ [ich5_sata] = &ich5_map_db,
+ [esb_sata] = &ich5_map_db,
+ [ich6_sata] = &ich6_map_db,
+ [ich6_sata_ahci] = &ich6_map_db,
+ [ich6m_sata_ahci] = &ich6m_map_db,
+ [ich7m_sata_ahci] = &ich7m_map_db,
+ [ich8_sata_ahci] = &ich8_map_db,
};
static struct ata_port_info piix_port_info[] = {
+ /* piix4_pata */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = 0x1f, /* pio0-4 */
+#if 0
+ .mwdma_mask = 0x06, /* mwdma1-2 */
+#else
+ .mwdma_mask = 0x00, /* mwdma broken */
+#endif
+ .udma_mask = ATA_UDMA_MASK_40C,
+ .port_ops = &piix_pata_ops,
+ },
+
/* ich5_pata */
{
.sht = &piix_sht,
- .host_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST |
- PIIX_FLAG_CHECKINTR,
- .pio_mask = 0x03, /* pio3-4 */
- .udma_mask = ATA_UDMA_MASK_40C, /* FIXME: cbl det */
+ .host_flags = ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR,
+ .pio_mask = 0x1f, /* pio0-4 */
+#if 0
+ .mwdma_mask = 0x06, /* mwdma1-2 */
+#else
+ .mwdma_mask = 0x00, /* mwdma broken */
+#endif
+ .udma_mask = 0x3f, /* udma0-5 */
.port_ops = &piix_pata_ops,
},
/* ich5_sata */
{
.sht = &piix_sht,
- .host_flags = ATA_FLAG_SATA | ATA_FLAG_SRST |
- PIIX_FLAG_COMBINED | PIIX_FLAG_CHECKINTR,
- .pio_mask = 0x03, /* pio3-4 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .host_flags = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR |
+ PIIX_FLAG_IGNORE_PCS,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
.port_ops = &piix_sata_ops,
},
- /* piix4_pata */
+ /* i6300esb_sata */
{
.sht = &piix_sht,
- .host_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
- .pio_mask = 0x03, /* pio3-4 */
- .udma_mask = ATA_UDMA_MASK_40C, /* FIXME: cbl det */
- .port_ops = &piix_pata_ops,
+ .host_flags = ATA_FLAG_SATA |
+ PIIX_FLAG_CHECKINTR | PIIX_FLAG_IGNORE_PCS,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
},
/* ich6_sata */
{
.sht = &piix_sht,
- .host_flags = ATA_FLAG_SATA | ATA_FLAG_SRST |
- PIIX_FLAG_COMBINED | PIIX_FLAG_CHECKINTR |
- ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x03, /* pio3-4 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .host_flags = ATA_FLAG_SATA |
+ PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich6_sata_ahci */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SATA |
+ PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich6m_sata_ahci */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SATA |
+ PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich7m_sata_ahci */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SATA |
+ PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich8_sata_ahci */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SATA |
+ PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
.port_ops = &piix_sata_ops,
},
};
MODULE_DESCRIPTION("SCSI low-level driver for Intel PIIX/ICH ATA controllers");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
+static int force_pcs = 0;
+module_param(force_pcs, int, 0444);
+MODULE_PARM_DESC(force_pcs, "force honoring or ignoring PCS to work around "
+ "device mis-detection (0=default, 1=ignore PCS, 2=honor PCS)");
/**
* piix_pata_cbl_detect - Probe host controller cable detect info
* @ap: Port for which cable detect info is desired
*
- * Read 80c cable indicator from SATA PCI device's PCI config
+ * Read 80c cable indicator from ATA PCI device's PCI config
* register. This register is normally set by firmware (BIOS).
*
* LOCKING:
*/
static void piix_pata_cbl_detect(struct ata_port *ap)
{
- struct pci_dev *pdev = ap->host_set->pdev;
+ struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
u8 tmp, mask;
/* no 80c support in host controller? */
goto cbl40;
/* check BIOS cable detect results */
- mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
+ mask = ap->hard_port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
pci_read_config_byte(pdev, PIIX_IOCFG, &tmp);
if ((tmp & mask) == 0)
goto cbl40;
}
/**
- * piix_pata_phy_reset - Probe specified port on PATA host controller
- * @ap: Port to probe
+ * piix_pata_prereset - prereset for PATA host controller
+ * @ap: Target port
*
- * Probe PATA phy.
+ * Prereset including cable detection.
*
* LOCKING:
* None (inherited from caller).
*/
-
-static void piix_pata_phy_reset(struct ata_port *ap)
+static int piix_pata_prereset(struct ata_port *ap)
{
- if (!pci_test_config_bits(ap->host_set->pdev,
- &piix_enable_bits[ap->port_no])) {
- ata_port_disable(ap);
- printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
- return;
+ struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+
+ if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->hard_port_no])) {
+ ata_port_printk(ap, KERN_INFO, "port disabled. ignoring.\n");
+ ap->eh_context.i.action &= ~ATA_EH_RESET_MASK;
+ return 0;
}
piix_pata_cbl_detect(ap);
- ata_port_probe(ap);
+ return ata_std_prereset(ap);
+}
- ata_bus_reset(ap);
+static void piix_pata_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, piix_pata_prereset, ata_std_softreset, NULL,
+ ata_std_postreset);
}
/**
- * piix_sata_probe - Probe PCI device for present SATA devices
- * @ap: Port associated with the PCI device we wish to probe
+ * piix_sata_present_mask - determine present mask for SATA host controller
+ * @ap: Target port
*
* Reads SATA PCI device's PCI config register Port Configuration
* and Status (PCS) to determine port and device availability.
* None (inherited from caller).
*
* RETURNS:
- * Non-zero if device detected, zero otherwise.
+ * determined present_mask
*/
-static int piix_sata_probe (struct ata_port *ap)
+static unsigned int piix_sata_present_mask(struct ata_port *ap)
{
- struct pci_dev *pdev = ap->host_set->pdev;
- int combined = (ap->flags & ATA_FLAG_SLAVE_POSS);
- int orig_mask, mask, i;
- u8 pcs;
-
- mask = (PIIX_PORT_PRESENT << ap->port_no) |
- (PIIX_PORT_ENABLED << ap->port_no);
-
- pci_read_config_byte(pdev, ICH5_PCS, &pcs);
- orig_mask = (int) pcs & 0xff;
-
- /* TODO: this is vaguely wrong for ICH6 combined mode,
- * where only two of the four SATA ports are mapped
- * onto a single ATA channel. It is also vaguely inaccurate
- * for ICH5, which has only two ports. However, this is ok,
- * as further device presence detection code will handle
- * any false positives produced here.
- */
-
- for (i = 0; i < 4; i++) {
- mask = (PIIX_PORT_PRESENT << i) | (PIIX_PORT_ENABLED << i);
-
- if ((orig_mask & mask) == mask)
- if (combined || (i == ap->port_no))
- return 1;
+ struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+ struct piix_host_priv *hpriv = ap->host_set->private_data;
+ const unsigned int *map = hpriv->map;
+ int base = 2 * ap->hard_port_no;
+ unsigned int present_mask = 0;
+ int port, i;
+ u16 pcs;
+
+ pci_read_config_word(pdev, ICH5_PCS, &pcs);
+ DPRINTK("ata%u: ENTER, pcs=0x%x base=%d\n", ap->id, pcs, base);
+
+ for (i = 0; i < 2; i++) {
+ port = map[base + i];
+ if (port < 0)
+ continue;
+ if ((ap->flags & PIIX_FLAG_IGNORE_PCS) ||
+ (pcs & 1 << (hpriv->map_db->present_shift + port)))
+ present_mask |= 1 << i;
}
- return 0;
+ DPRINTK("ata%u: LEAVE, pcs=0x%x present_mask=0x%x\n",
+ ap->id, pcs, present_mask);
+
+ return present_mask;
}
/**
- * piix_sata_phy_reset - Probe specified port on SATA host controller
- * @ap: Port to probe
+ * piix_sata_softreset - reset SATA host port via ATA SRST
+ * @ap: port to reset
+ * @classes: resulting classes of attached devices
*
- * Probe SATA phy.
+ * Reset SATA host port via ATA SRST. On controllers with
+ * reliable PCS present bits, the bits are used to determine
+ * device presence.
*
* LOCKING:
- * None (inherited from caller).
+ * Kernel thread context (may sleep)
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
*/
-
-static void piix_sata_phy_reset(struct ata_port *ap)
+static int piix_sata_softreset(struct ata_port *ap, unsigned int *classes)
{
- if (!piix_sata_probe(ap)) {
- ata_port_disable(ap);
- printk(KERN_INFO "ata%u: SATA port has no device.\n", ap->id);
- return;
- }
+ unsigned int present_mask;
+ int i, rc;
+
+ present_mask = piix_sata_present_mask(ap);
+
+ rc = ata_std_softreset(ap, classes);
+ if (rc)
+ return rc;
- ap->cbl = ATA_CBL_SATA;
+ for (i = 0; i < ATA_MAX_DEVICES; i++) {
+ if (!(present_mask & (1 << i)))
+ classes[i] = ATA_DEV_NONE;
+ }
- ata_port_probe(ap);
+ return 0;
+}
- ata_bus_reset(ap);
+static void piix_sata_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, ata_std_prereset, piix_sata_softreset, NULL,
+ ata_std_postreset);
}
/**
* piix_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
* @adev: um
- * @pio: PIO mode, 0 - 4
*
* Set PIO mode for device, in host controller PCI config space.
*
* None (inherited from caller).
*/
-static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev,
- unsigned int pio)
+static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *dev = ap->host_set->pdev;
- unsigned int is_slave = (adev->flags & ATA_DFLAG_MASTER) ? 0 : 1;
- unsigned int master_port= ap->port_no ? 0x42 : 0x40;
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ struct pci_dev *dev = to_pci_dev(ap->host_set->dev);
+ unsigned int is_slave = (adev->devno != 0);
+ unsigned int master_port= ap->hard_port_no ? 0x42 : 0x40;
unsigned int slave_port = 0x44;
u16 master_data;
u8 slave_data;
/* enable PPE, IE and TIME */
master_data |= 0x0070;
pci_read_config_byte(dev, slave_port, &slave_data);
- slave_data &= (ap->port_no ? 0x0f : 0xf0);
+ slave_data &= (ap->hard_port_no ? 0x0f : 0xf0);
slave_data |=
(timings[pio][0] << 2) |
- (timings[pio][1] << (ap->port_no ? 4 : 0));
+ (timings[pio][1] << (ap->hard_port_no ? 4 : 0));
} else {
master_data &= 0xccf8;
/* enable PPE, IE and TIME */
}
/**
- * piix_set_udmamode - Initialize host controller PATA PIO timings
+ * piix_set_dmamode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
* @adev: um
* @udma: udma mode, 0 - 6
* None (inherited from caller).
*/
-static void piix_set_udmamode (struct ata_port *ap, struct ata_device *adev,
- unsigned int udma)
+static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *dev = ap->host_set->pdev;
- u8 maslave = ap->port_no ? 0x42 : 0x40;
+ unsigned int udma = adev->dma_mode; /* FIXME: MWDMA too */
+ struct pci_dev *dev = to_pci_dev(ap->host_set->dev);
+ u8 maslave = ap->hard_port_no ? 0x42 : 0x40;
u8 speed = udma;
- unsigned int drive_dn = (ap->port_no ? 2 : 0) + adev->devno;
+ unsigned int drive_dn = (ap->hard_port_no ? 2 : 0) + adev->devno;
int a_speed = 3 << (drive_dn * 4);
int u_flag = 1 << drive_dn;
int v_flag = 0x01 << drive_dn;
case XFER_UDMA_3:
case XFER_UDMA_1: u_speed = 1 << (drive_dn * 4); break;
case XFER_UDMA_0: u_speed = 0 << (drive_dn * 4); break;
+ case XFER_MW_DMA_2:
+ case XFER_MW_DMA_1: break;
default:
BUG();
return;
}
- if (!(reg48 & u_flag))
- pci_write_config_byte(dev, 0x48, reg48 | u_flag);
- if (speed == XFER_UDMA_5) {
- pci_write_config_byte(dev, 0x55, (u8) reg55|w_flag);
+ if (speed >= XFER_UDMA_0) {
+ if (!(reg48 & u_flag))
+ pci_write_config_byte(dev, 0x48, reg48 | u_flag);
+ if (speed == XFER_UDMA_5) {
+ pci_write_config_byte(dev, 0x55, (u8) reg55|w_flag);
+ } else {
+ pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
+ }
+ if ((reg4a & a_speed) != u_speed)
+ pci_write_config_word(dev, 0x4a, (reg4a & ~a_speed) | u_speed);
+ if (speed > XFER_UDMA_2) {
+ if (!(reg54 & v_flag))
+ pci_write_config_byte(dev, 0x54, reg54 | v_flag);
+ } else
+ pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
} else {
- pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
+ if (reg48 & u_flag)
+ pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
+ if (reg4a & a_speed)
+ pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
+ if (reg54 & v_flag)
+ pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
+ if (reg55 & w_flag)
+ pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
+ }
+}
+
+#define AHCI_PCI_BAR 5
+#define AHCI_GLOBAL_CTL 0x04
+#define AHCI_ENABLE (1 << 31)
+static int piix_disable_ahci(struct pci_dev *pdev)
+{
+ void __iomem *mmio;
+ u32 tmp;
+ int rc = 0;
+
+ /* BUG: pci_enable_device has not yet been called. This
+ * works because this device is usually set up by BIOS.
+ */
+
+ if (!pci_resource_start(pdev, AHCI_PCI_BAR) ||
+ !pci_resource_len(pdev, AHCI_PCI_BAR))
+ return 0;
+
+ mmio = pci_iomap(pdev, AHCI_PCI_BAR, 64);
+ if (!mmio)
+ return -ENOMEM;
+
+ tmp = readl(mmio + AHCI_GLOBAL_CTL);
+ if (tmp & AHCI_ENABLE) {
+ tmp &= ~AHCI_ENABLE;
+ writel(tmp, mmio + AHCI_GLOBAL_CTL);
+
+ tmp = readl(mmio + AHCI_GLOBAL_CTL);
+ if (tmp & AHCI_ENABLE)
+ rc = -EIO;
+ }
+
+ pci_iounmap(pdev, mmio);
+ return rc;
+}
+
+/**
+ * piix_check_450nx_errata - Check for problem 450NX setup
+ * @ata_dev: the PCI device to check
+ *
+ * Check for the present of 450NX errata #19 and errata #25. If
+ * they are found return an error code so we can turn off DMA
+ */
+
+static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev)
+{
+ struct pci_dev *pdev = NULL;
+ u16 cfg;
+ u8 rev;
+ int no_piix_dma = 0;
+
+ while((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL)
+ {
+ /* Look for 450NX PXB. Check for problem configurations
+ A PCI quirk checks bit 6 already */
+ pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+ pci_read_config_word(pdev, 0x41, &cfg);
+ /* Only on the original revision: IDE DMA can hang */
+ if (rev == 0x00)
+ no_piix_dma = 1;
+ /* On all revisions below 5 PXB bus lock must be disabled for IDE */
+ else if (cfg & (1<<14) && rev < 5)
+ no_piix_dma = 2;
+ }
+ if (no_piix_dma)
+ dev_printk(KERN_WARNING, &ata_dev->dev, "450NX errata present, disabling IDE DMA.\n");
+ if (no_piix_dma == 2)
+ dev_printk(KERN_WARNING, &ata_dev->dev, "A BIOS update may resolve this.\n");
+ return no_piix_dma;
+}
+
+static void __devinit piix_init_pcs(struct pci_dev *pdev,
+ struct ata_port_info *pinfo,
+ const struct piix_map_db *map_db)
+{
+ u16 pcs, new_pcs;
+
+ pci_read_config_word(pdev, ICH5_PCS, &pcs);
+
+ new_pcs = pcs | map_db->port_enable;
+
+ if (new_pcs != pcs) {
+ DPRINTK("updating PCS from 0x%x to 0x%x\n", pcs, new_pcs);
+ pci_write_config_word(pdev, ICH5_PCS, new_pcs);
+ msleep(150);
+ }
+
+ if (force_pcs == 1) {
+ dev_printk(KERN_INFO, &pdev->dev,
+ "force ignoring PCS (0x%x)\n", new_pcs);
+ pinfo[0].host_flags |= PIIX_FLAG_IGNORE_PCS;
+ pinfo[1].host_flags |= PIIX_FLAG_IGNORE_PCS;
+ } else if (force_pcs == 2) {
+ dev_printk(KERN_INFO, &pdev->dev,
+ "force honoring PCS (0x%x)\n", new_pcs);
+ pinfo[0].host_flags &= ~PIIX_FLAG_IGNORE_PCS;
+ pinfo[1].host_flags &= ~PIIX_FLAG_IGNORE_PCS;
}
- if ((reg4a & a_speed) != u_speed)
- pci_write_config_word(dev, 0x4a, (reg4a & ~a_speed) | u_speed);
- if (speed > XFER_UDMA_2) {
- if (!(reg54 & v_flag))
- pci_write_config_byte(dev, 0x54, reg54 | v_flag);
- } else
- pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
}
-/* move to PCI layer, integrate w/ MSI stuff */
-static void pci_enable_intx(struct pci_dev *pdev)
+static void __devinit piix_init_sata_map(struct pci_dev *pdev,
+ struct ata_port_info *pinfo,
+ const struct piix_map_db *map_db)
{
- u16 pci_command;
+ struct piix_host_priv *hpriv = pinfo[0].private_data;
+ const unsigned int *map;
+ int i, invalid_map = 0;
+ u8 map_value;
- pci_read_config_word(pdev, PCI_COMMAND, &pci_command);
- if (pci_command & PCI_COMMAND_INTX_DISABLE) {
- pci_command &= ~PCI_COMMAND_INTX_DISABLE;
- pci_write_config_word(pdev, PCI_COMMAND, pci_command);
+ pci_read_config_byte(pdev, ICH5_PMR, &map_value);
+
+ map = map_db->map[map_value & map_db->mask];
+
+ dev_printk(KERN_INFO, &pdev->dev, "MAP [");
+ for (i = 0; i < 4; i++) {
+ switch (map[i]) {
+ case RV:
+ invalid_map = 1;
+ printk(" XX");
+ break;
+
+ case NA:
+ printk(" --");
+ break;
+
+ case IDE:
+ WARN_ON((i & 1) || map[i + 1] != IDE);
+ pinfo[i / 2] = piix_port_info[ich5_pata];
+ pinfo[i / 2].private_data = hpriv;
+ i++;
+ printk(" IDE IDE");
+ break;
+
+ default:
+ printk(" P%d", map[i]);
+ if (i & 1)
+ pinfo[i / 2].host_flags |= ATA_FLAG_SLAVE_POSS;
+ break;
+ }
}
+ printk(" ]\n");
+
+ if (invalid_map)
+ dev_printk(KERN_ERR, &pdev->dev,
+ "invalid MAP value %u\n", map_value);
+
+ hpriv->map = map;
+ hpriv->map_db = map_db;
}
/**
static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
- struct ata_port_info *port_info[2];
- unsigned int combined = 0, n_ports = 1;
- unsigned int pata_chan = 0, sata_chan = 0;
+ struct ata_port_info port_info[2];
+ struct ata_port_info *ppinfo[2] = { &port_info[0], &port_info[1] };
+ struct piix_host_priv *hpriv;
+ unsigned long host_flags;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "version " DRV_VERSION "\n");
/* no hotplugging support (FIXME) */
if (!in_module_init)
return -ENODEV;
- port_info[0] = &piix_port_info[ent->driver_data];
- port_info[1] = NULL;
+ hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL);
+ if (!hpriv)
+ return -ENOMEM;
- if (port_info[0]->host_flags & PIIX_FLAG_COMBINED) {
+ port_info[0] = piix_port_info[ent->driver_data];
+ port_info[1] = piix_port_info[ent->driver_data];
+ port_info[0].private_data = hpriv;
+ port_info[1].private_data = hpriv;
+
+ host_flags = port_info[0].host_flags;
+
+ if (host_flags & PIIX_FLAG_AHCI) {
u8 tmp;
- pci_read_config_byte(pdev, ICH5_PMR, &tmp);
-
- if (tmp & PIIX_COMB) {
- combined = 1;
- if (tmp & PIIX_COMB_PATA_P0)
- sata_chan = 1;
- else
- pata_chan = 1;
+ pci_read_config_byte(pdev, PIIX_SCC, &tmp);
+ if (tmp == PIIX_AHCI_DEVICE) {
+ int rc = piix_disable_ahci(pdev);
+ if (rc)
+ return rc;
}
}
+ /* Initialize SATA map */
+ if (host_flags & ATA_FLAG_SATA) {
+ piix_init_sata_map(pdev, port_info,
+ piix_map_db_table[ent->driver_data]);
+ piix_init_pcs(pdev, port_info,
+ piix_map_db_table[ent->driver_data]);
+ }
+
/* On ICH5, some BIOSen disable the interrupt using the
* PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3.
* On ICH6, this bit has the same effect, but only when
* MSI is disabled (and it is disabled, as we don't use
* message-signalled interrupts currently).
*/
- if (port_info[0]->host_flags & PIIX_FLAG_CHECKINTR)
- pci_enable_intx(pdev);
-
- if (combined) {
- port_info[sata_chan] = &piix_port_info[ent->driver_data];
- port_info[sata_chan]->host_flags |= ATA_FLAG_SLAVE_POSS;
- port_info[pata_chan] = &piix_port_info[ich5_pata];
- n_ports++;
-
- printk(KERN_WARNING DRV_NAME ": combined mode detected\n");
+ if (host_flags & PIIX_FLAG_CHECKINTR)
+ pci_intx(pdev, 1);
+
+ if (piix_check_450nx_errata(pdev)) {
+ /* This writes into the master table but it does not
+ really matter for this errata as we will apply it to
+ all the PIIX devices on the board */
+ port_info[0].mwdma_mask = 0;
+ port_info[0].udma_mask = 0;
+ port_info[1].mwdma_mask = 0;
+ port_info[1].udma_mask = 0;
}
-
- return ata_pci_init_one(pdev, port_info, n_ports);
+ return ata_pci_init_one(pdev, ppinfo, 2);
}
-/**
- * piix_init -
- *
- * LOCKING:
- *
- * RETURNS:
- *
- */
+static void piix_host_stop(struct ata_host_set *host_set)
+{
+ if (host_set->next == NULL)
+ kfree(host_set->private_data);
+ ata_host_stop(host_set);
+}
static int __init piix_init(void)
{
return 0;
}
-/**
- * piix_exit -
- *
- * LOCKING:
- *
- */
-
static void __exit piix_exit(void)
{
pci_unregister_driver(&piix_pci_driver);
git://git.onelab.eu / linux-2.6.git / blobdiff