/*
- * ata_k2.c - Broadcom (Apple K2) SATA
+ * sata_svw.c - ServerWorks / Apple K2 SATA
+ *
+ * Maintained by: Benjamin Herrenschmidt <benh@kernel.crashing.org> and
+ * Jeff Garzik <jgarzik@pobox.com>
+ * Please ALWAYS copy linux-ide@vger.kernel.org
+ * on emails.
*
* Copyright 2003 Benjamin Herrenschmidt <benh@kernel.crashing.org>
*
* This driver probably works with non-Apple versions of the
* Broadcom chipset...
*
- * The contents of this file are subject to the Open
- * Software License version 1.1 that can be found at
- * http://www.opensource.org/licenses/osl-1.1.txt and is included herein
- * by reference.
*
- * Alternatively, the contents of this file may be used under the terms
- * of the GNU General Public License version 2 (the "GPL") as distributed
- * in the kernel source COPYING file, in which case the provisions of
- * the GPL are applicable instead of the above. If you wish to allow
- * the use of your version of this file only under the terms of the
- * GPL and not to allow others to use your version of this file under
- * the OSL, indicate your decision by deleting the provisions above and
- * replace them with the notice and other provisions required by the GPL.
- * If you do not delete the provisions above, a recipient may use your
- * version of this file under either the OSL or the GPL.
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING. If not, write to
+ * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *
+ * libata documentation is available via 'make {ps|pdf}docs',
+ * as Documentation/DocBook/libata.*
+ *
+ * Hardware documentation available under NDA.
*
*/
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
-#include "scsi.h"
-#include "hosts.h"
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
#include <linux/libata.h>
#ifdef CONFIG_PPC_OF
#endif /* CONFIG_PPC_OF */
#define DRV_NAME "sata_svw"
-#define DRV_VERSION "1.04"
-
-/* Taskfile registers offsets */
-#define K2_SATA_TF_CMD_OFFSET 0x00
-#define K2_SATA_TF_DATA_OFFSET 0x00
-#define K2_SATA_TF_ERROR_OFFSET 0x04
-#define K2_SATA_TF_NSECT_OFFSET 0x08
-#define K2_SATA_TF_LBAL_OFFSET 0x0c
-#define K2_SATA_TF_LBAM_OFFSET 0x10
-#define K2_SATA_TF_LBAH_OFFSET 0x14
-#define K2_SATA_TF_DEVICE_OFFSET 0x18
-#define K2_SATA_TF_CMDSTAT_OFFSET 0x1c
-#define K2_SATA_TF_CTL_OFFSET 0x20
-
-/* DMA base */
-#define K2_SATA_DMA_CMD_OFFSET 0x30
-
-/* SCRs base */
-#define K2_SATA_SCR_STATUS_OFFSET 0x40
-#define K2_SATA_SCR_ERROR_OFFSET 0x44
-#define K2_SATA_SCR_CONTROL_OFFSET 0x48
-
-/* Others */
-#define K2_SATA_SICR1_OFFSET 0x80
-#define K2_SATA_SICR2_OFFSET 0x84
-#define K2_SATA_SIM_OFFSET 0x88
+#define DRV_VERSION "1.07"
+
+enum {
+ /* Taskfile registers offsets */
+ K2_SATA_TF_CMD_OFFSET = 0x00,
+ K2_SATA_TF_DATA_OFFSET = 0x00,
+ K2_SATA_TF_ERROR_OFFSET = 0x04,
+ K2_SATA_TF_NSECT_OFFSET = 0x08,
+ K2_SATA_TF_LBAL_OFFSET = 0x0c,
+ K2_SATA_TF_LBAM_OFFSET = 0x10,
+ K2_SATA_TF_LBAH_OFFSET = 0x14,
+ K2_SATA_TF_DEVICE_OFFSET = 0x18,
+ K2_SATA_TF_CMDSTAT_OFFSET = 0x1c,
+ K2_SATA_TF_CTL_OFFSET = 0x20,
+
+ /* DMA base */
+ K2_SATA_DMA_CMD_OFFSET = 0x30,
+
+ /* SCRs base */
+ K2_SATA_SCR_STATUS_OFFSET = 0x40,
+ K2_SATA_SCR_ERROR_OFFSET = 0x44,
+ K2_SATA_SCR_CONTROL_OFFSET = 0x48,
+
+ /* Others */
+ K2_SATA_SICR1_OFFSET = 0x80,
+ K2_SATA_SICR2_OFFSET = 0x84,
+ K2_SATA_SIM_OFFSET = 0x88,
+
+ /* Port stride */
+ K2_SATA_PORT_OFFSET = 0x100,
+};
-/* Port stride */
-#define K2_SATA_PORT_OFFSET 0x100
+static u8 k2_stat_check_status(struct ata_port *ap);
static u32 k2_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
}
-static void k2_sata_tf_load(struct ata_port *ap, struct ata_taskfile *tf)
+static void k2_sata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
static void k2_sata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
- u16 nsect, lbal, lbam, lbah;
+ u16 nsect, lbal, lbam, lbah, feature;
- nsect = tf->nsect = readw(ioaddr->nsect_addr);
- lbal = tf->lbal = readw(ioaddr->lbal_addr);
- lbam = tf->lbam = readw(ioaddr->lbam_addr);
- lbah = tf->lbah = readw(ioaddr->lbah_addr);
+ tf->command = k2_stat_check_status(ap);
tf->device = readw(ioaddr->device_addr);
+ feature = readw(ioaddr->error_addr);
+ nsect = readw(ioaddr->nsect_addr);
+ lbal = readw(ioaddr->lbal_addr);
+ lbam = readw(ioaddr->lbam_addr);
+ lbah = readw(ioaddr->lbah_addr);
+
+ tf->feature = feature;
+ tf->nsect = nsect;
+ tf->lbal = lbal;
+ tf->lbam = lbam;
+ tf->lbah = lbah;
if (tf->flags & ATA_TFLAG_LBA48) {
- tf->hob_feature = readw(ioaddr->error_addr) >> 8;
+ tf->hob_feature = feature >> 8;
tf->hob_nsect = nsect >> 8;
tf->hob_lbal = lbal >> 8;
tf->hob_lbam = lbam >> 8;
}
}
+/**
+ * k2_bmdma_setup_mmio - Set up PCI IDE BMDMA transaction (MMIO)
+ * @qc: Info associated with this ATA transaction.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ */
+
+static void k2_bmdma_setup_mmio (struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
+ u8 dmactl;
+ void *mmio = (void *) ap->ioaddr.bmdma_addr;
+ /* load PRD table addr. */
+ mb(); /* make sure PRD table writes are visible to controller */
+ writel(ap->prd_dma, mmio + ATA_DMA_TABLE_OFS);
+
+ /* specify data direction, triple-check start bit is clear */
+ dmactl = readb(mmio + ATA_DMA_CMD);
+ dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
+ if (!rw)
+ dmactl |= ATA_DMA_WR;
+ writeb(dmactl, mmio + ATA_DMA_CMD);
+
+ /* issue r/w command if this is not a ATA DMA command*/
+ if (qc->tf.protocol != ATA_PROT_DMA)
+ ap->ops->exec_command(ap, &qc->tf);
+}
+
+/**
+ * k2_bmdma_start_mmio - Start a PCI IDE BMDMA transaction (MMIO)
+ * @qc: Info associated with this ATA transaction.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ */
+
+static void k2_bmdma_start_mmio (struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ void *mmio = (void *) ap->ioaddr.bmdma_addr;
+ u8 dmactl;
+
+ /* start host DMA transaction */
+ dmactl = readb(mmio + ATA_DMA_CMD);
+ writeb(dmactl | ATA_DMA_START, mmio + ATA_DMA_CMD);
+ /* There is a race condition in certain SATA controllers that can
+ be seen when the r/w command is given to the controller before the
+ host DMA is started. On a Read command, the controller would initiate
+ the command to the drive even before it sees the DMA start. When there
+ are very fast drives connected to the controller, or when the data request
+ hits in the drive cache, there is the possibility that the drive returns a part
+ or all of the requested data to the controller before the DMA start is issued.
+ In this case, the controller would become confused as to what to do with the data.
+ In the worst case when all the data is returned back to the controller, the
+ controller could hang. In other cases it could return partial data returning
+ in data corruption. This problem has been seen in PPC systems and can also appear
+ on an system with very fast disks, where the SATA controller is sitting behind a
+ number of bridges, and hence there is significant latency between the r/w command
+ and the start command. */
+ /* issue r/w command if the access is to ATA*/
+ if (qc->tf.protocol == ATA_PROT_DMA)
+ ap->ops->exec_command(ap, &qc->tf);
+}
+
static u8 k2_stat_check_status(struct ata_port *ap)
{
return 0;
/* Find the OF node for the PCI device proper */
- np = pci_device_to_OF_node(ap->host_set->pdev);
+ np = pci_device_to_OF_node(to_pci_dev(ap->host_set->dev));
if (np == NULL)
return 0;
#endif /* CONFIG_PPC_OF */
-static Scsi_Host_Template k2_sata_sht = {
+static struct scsi_host_template k2_sata_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
- .eh_strategy_handler = ata_scsi_error,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
- .max_sectors = ATA_MAX_SECTORS,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
};
-static struct ata_port_operations k2_sata_ops = {
+static const struct ata_port_operations k2_sata_ops = {
.port_disable = ata_port_disable,
.tf_load = k2_sata_tf_load,
.tf_read = k2_sata_tf_read,
.check_status = k2_stat_check_status,
- .exec_command = ata_exec_command_mmio,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
.phy_reset = sata_phy_reset,
- .bmdma_start = ata_bmdma_start_mmio,
- .fill_sg = ata_fill_sg,
+ .bmdma_setup = k2_bmdma_setup_mmio,
+ .bmdma_start = k2_bmdma_start_mmio,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
.eng_timeout = ata_eng_timeout,
.irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
.scr_read = k2_sata_scr_read,
.scr_write = k2_sata_scr_write,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
+ .host_stop = ata_pci_host_stop,
};
static void k2_sata_setup_port(struct ata_ioports *port, unsigned long base)
static int printed_version;
struct ata_probe_ent *probe_ent = NULL;
unsigned long base;
- void *mmio_base;
+ void __iomem *mmio_base;
+ int pci_dev_busy = 0;
int rc;
+ int i;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
/*
* If this driver happens to only be useful on Apple's K2, then
/* Request PCI regions */
rc = pci_request_regions(pdev, DRV_NAME);
- if (rc)
+ if (rc) {
+ pci_dev_busy = 1;
goto err_out;
+ }
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
}
memset(probe_ent, 0, sizeof(*probe_ent));
- probe_ent->pdev = pdev;
+ probe_ent->dev = pci_dev_to_dev(pdev);
INIT_LIST_HEAD(&probe_ent->node);
- mmio_base = ioremap(pci_resource_start(pdev, 5),
- pci_resource_len(pdev, 5));
+ mmio_base = pci_iomap(pdev, 5, 0);
if (mmio_base == NULL) {
rc = -ENOMEM;
goto err_out_free_ent;
/* Clear a magic bit in SCR1 according to Darwin, those help
* some funky seagate drives (though so far, those were already
- * set by the firmware on the machines I had access to
+ * set by the firmware on the machines I had access to)
*/
writel(readl(mmio_base + K2_SATA_SICR1_OFFSET) & ~0x00040000,
mmio_base + K2_SATA_SICR1_OFFSET);
* if we don't fill these
*/
probe_ent->pio_mask = 0x1f;
+ probe_ent->mwdma_mask = 0x7;
probe_ent->udma_mask = 0x7f;
- /* We have 4 ports per PCI function */
- k2_sata_setup_port(&probe_ent->port[0], base + 0 * K2_SATA_PORT_OFFSET);
- k2_sata_setup_port(&probe_ent->port[1], base + 1 * K2_SATA_PORT_OFFSET);
- k2_sata_setup_port(&probe_ent->port[2], base + 2 * K2_SATA_PORT_OFFSET);
- k2_sata_setup_port(&probe_ent->port[3], base + 3 * K2_SATA_PORT_OFFSET);
+ /* different controllers have different number of ports - currently 4 or 8 */
+ /* All ports are on the same function. Multi-function device is no
+ * longer available. This should not be seen in any system. */
+ for (i = 0; i < ent->driver_data; i++)
+ k2_sata_setup_port(&probe_ent->port[i], base + i * K2_SATA_PORT_OFFSET);
pci_set_master(pdev);
err_out_regions:
pci_release_regions(pdev);
err_out:
- pci_disable_device(pdev);
+ if (!pci_dev_busy)
+ pci_disable_device(pdev);
return rc;
}
-
-static struct pci_device_id k2_sata_pci_tbl[] = {
- { 0x1166, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+/* 0x240 is device ID for Apple K2 device
+ * 0x241 is device ID for Serverworks Frodo4
+ * 0x242 is device ID for Serverworks Frodo8
+ * 0x24a is device ID for BCM5785 (aka HT1000) HT southbridge integrated SATA
+ * controller
+ * */
+static const struct pci_device_id k2_sata_pci_tbl[] = {
+ { 0x1166, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
+ { 0x1166, 0x0241, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
+ { 0x1166, 0x0242, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
+ { 0x1166, 0x024a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
+ { 0x1166, 0x024b, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
{ }
};
return pci_module_init(&k2_sata_pci_driver);
}
+
static void __exit k2_sata_exit(void)
{
pci_unregister_driver(&k2_sata_pci_driver);
MODULE_DESCRIPTION("low-level driver for K2 SATA controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, k2_sata_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
module_init(k2_sata_init);
module_exit(k2_sata_exit);
git://git.onelab.eu / linux-2.6.git / blobdiff