#include <linux/interrupt.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
-#include <linux/config.h>
#include <linux/major.h>
#include <linux/string.h>
#include <linux/fcntl.h>
#include <linux/keyboard.h>
#include <linux/init.h>
#include <linux/pm.h>
+#include <linux/pm_legacy.h>
#include <linux/bitops.h>
#include <linux/delay.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
-#include <asm/segment.h>
#include <asm/delay.h>
#include <asm/uaccess.h>
#define RS_ISR_PASS_LIMIT 256
-#define _INLINE_ inline
-
static void change_speed(struct m68k_serial *info);
/*
static int m68328_console_cbaud = DEFAULT_CBAUD;
-/*
- * tmp_buf is used as a temporary buffer by serial_write. We need to
- * lock it in case the memcpy_fromfs blocks while swapping in a page,
- * and some other program tries to do a serial write at the same time.
- * Since the lock will only come under contention when the system is
- * swapping and available memory is low, it makes sense to share one
- * buffer across all the serial ports, since it significantly saves
- * memory if large numbers of serial ports are open.
- */
-static unsigned char tmp_buf[SERIAL_XMIT_SIZE]; /* This is cheating */
-DECLARE_MUTEX(tmp_buf_sem);
-
static inline int serial_paranoia_check(struct m68k_serial *info,
char *name, const char *routine)
{
if (serial_paranoia_check(info, tty->name, "rs_stop"))
return;
- save_flags(flags); cli();
+ local_irq_save(flags);
uart->ustcnt &= ~USTCNT_TXEN;
- restore_flags(flags);
+ local_irq_restore(flags);
}
static void rs_put_char(char ch)
{
int flags, loops = 0;
- save_flags(flags); cli();
+ local_irq_save(flags);
while (!(UTX & UTX_TX_AVAIL) && (loops < 1000)) {
loops++;
UTX_TXDATA = ch;
udelay(5);
- restore_flags(flags);
+ local_irq_restore(flags);
}
static void rs_start(struct tty_struct *tty)
if (serial_paranoia_check(info, tty->name, "rs_start"))
return;
- save_flags(flags); cli();
+ local_irq_save(flags);
if (info->xmit_cnt && info->xmit_buf && !(uart->ustcnt & USTCNT_TXEN)) {
#ifdef USE_INTS
uart->ustcnt |= USTCNT_TXEN | USTCNT_TX_INTR_MASK;
uart->ustcnt |= USTCNT_TXEN;
#endif
}
- restore_flags(flags);
+ local_irq_restore(flags);
}
/* Drop into either the boot monitor or kadb upon receiving a break
/* Drop into the debugger */
}
-static _INLINE_ void status_handle(struct m68k_serial *info, unsigned short status)
+static void status_handle(struct m68k_serial *info, unsigned short status)
{
#if 0
if(status & DCD) {
return;
}
-static _INLINE_ void receive_chars(struct m68k_serial *info, struct pt_regs *regs, unsigned short rx)
+static void receive_chars(struct m68k_serial *info, unsigned short rx)
{
struct tty_struct *tty = info->tty;
m68328_uart *uart = &uart_addr[info->line];
- unsigned char ch;
+ unsigned char ch, flag;
/*
* This do { } while() loop will get ALL chars out of Rx FIFO
/* show_net_buffers(); */
return;
} else if (ch == 0x12) { /* ^R */
- machine_restart(NULL);
+ emergency_restart();
return;
#endif /* CONFIG_MAGIC_SYSRQ */
}
if(!tty)
goto clear_and_exit;
- /*
- * Make sure that we do not overflow the buffer
- */
- if (tty->flip.count >= TTY_FLIPBUF_SIZE) {
- schedule_work(&tty->flip.work);
- return;
- }
+ flag = TTY_NORMAL;
if(rx & URX_PARITY_ERROR) {
- *tty->flip.flag_buf_ptr++ = TTY_PARITY;
+ flag = TTY_PARITY;
status_handle(info, rx);
} else if(rx & URX_OVRUN) {
- *tty->flip.flag_buf_ptr++ = TTY_OVERRUN;
+ flag = TTY_OVERRUN;
status_handle(info, rx);
} else if(rx & URX_FRAME_ERROR) {
- *tty->flip.flag_buf_ptr++ = TTY_FRAME;
+ flag = TTY_FRAME;
status_handle(info, rx);
- } else {
- *tty->flip.flag_buf_ptr++ = 0; /* XXX */
}
- *tty->flip.char_buf_ptr++ = ch;
- tty->flip.count++;
-
+ tty_insert_flip_char(tty, ch, flag);
#ifndef CONFIG_XCOPILOT_BUGS
} while((rx = uart->urx.w) & URX_DATA_READY);
#endif
- schedule_work(&tty->flip.work);
+ tty_schedule_flip(tty);
clear_and_exit:
return;
}
-static _INLINE_ void transmit_chars(struct m68k_serial *info)
+static void transmit_chars(struct m68k_serial *info)
{
m68328_uart *uart = &uart_addr[info->line];
/*
* This is the serial driver's generic interrupt routine
*/
-irqreturn_t rs_interrupt(int irq, void *dev_id, struct pt_regs * regs)
+irqreturn_t rs_interrupt(int irq, void *dev_id)
{
struct m68k_serial * info;
m68328_uart *uart;
#ifdef USE_INTS
tx = uart->utx.w;
- if (rx & URX_DATA_READY) receive_chars(info, regs, rx);
+ if (rx & URX_DATA_READY) receive_chars(info, rx);
if (tx & UTX_TX_AVAIL) transmit_chars(info);
#else
- receive_chars(info, regs, rx);
+ receive_chars(info, rx);
#endif
return IRQ_HANDLED;
}
return -ENOMEM;
}
- save_flags(flags); cli();
+ local_irq_save(flags);
/*
* Clear the FIFO buffers and disable them
change_speed(info);
info->flags |= S_INITIALIZED;
- restore_flags(flags);
+ local_irq_restore(flags);
return 0;
}
if (!(info->flags & S_INITIALIZED))
return;
- save_flags(flags); cli(); /* Disable interrupts */
+ local_irq_save(flags);
if (info->xmit_buf) {
free_page((unsigned long) info->xmit_buf);
set_bit(TTY_IO_ERROR, &info->tty->flags);
info->flags &= ~S_INITIALIZED;
- restore_flags(flags);
+ local_irq_restore(flags);
}
struct {
if (info == 0) return;
if (info->xmit_buf == 0) return;
- save_flags(flags); cli();
+ local_irq_save(flags);
left = info->xmit_cnt;
while (left != 0) {
c = info->xmit_buf[info->xmit_tail];
info->xmit_tail = (info->xmit_tail+1) & (SERIAL_XMIT_SIZE-1);
info->xmit_cnt--;
- restore_flags(flags);
+ local_irq_restore(flags);
rs_put_char(c);
- save_flags(flags); cli();
+ local_irq_save(flags);
left = min(info->xmit_cnt, left-1);
}
/* Last character is being transmitted now (hopefully). */
udelay(5);
- restore_flags(flags);
+ local_irq_restore(flags);
return;
}
#endif
/* Enable transmitter */
- save_flags(flags); cli();
+ local_irq_save(flags);
if (info->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped ||
!info->xmit_buf) {
- restore_flags(flags);
+ local_irq_restore(flags);
return;
}
while (!(uart->utx.w & UTX_TX_AVAIL)) udelay(5);
}
#endif
- restore_flags(flags);
+ local_irq_restore(flags);
}
extern void console_printn(const char * b, int count);
if (!tty || !info->xmit_buf)
return 0;
- save_flags(flags);
+ local_save_flags(flags);
while (1) {
- cli();
+ local_irq_disable();
c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
SERIAL_XMIT_SIZE - info->xmit_head));
+ local_irq_restore(flags);
+
if (c <= 0)
break;
memcpy(info->xmit_buf + info->xmit_head, buf, c);
+
+ local_irq_disable();
info->xmit_head = (info->xmit_head + c) & (SERIAL_XMIT_SIZE-1);
info->xmit_cnt += c;
- restore_flags(flags);
+ local_irq_restore(flags);
buf += c;
count -= c;
total += c;
if (info->xmit_cnt && !tty->stopped && !tty->hw_stopped) {
/* Enable transmitter */
- cli();
+ local_irq_disable();
#ifndef USE_INTS
while(info->xmit_cnt) {
#endif
#ifndef USE_INTS
}
#endif
- restore_flags(flags);
+ local_irq_restore(flags);
}
- restore_flags(flags);
+
return total;
}
static void rs_flush_buffer(struct tty_struct *tty)
{
struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
+ unsigned long flags;
if (serial_paranoia_check(info, tty->name, "rs_flush_buffer"))
return;
- cli();
+ local_irq_save(flags);
info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
- sti();
+ local_irq_restore(flags);
tty_wakeup(tty);
}
m68328_uart *uart = &uart_addr[info->line];
#endif
unsigned char status;
+ unsigned long flags;
- cli();
+ local_irq_save(flags);
#ifdef CONFIG_SERIAL_68328_RTS_CTS
status = (uart->utx.w & UTX_CTS_STAT) ? 1 : 0;
#else
status = 0;
#endif
- sti();
+ local_irq_restore(flags);
put_user(status,value);
return 0;
}
/*
* This routine sends a break character out the serial port.
*/
-static void send_break( struct m68k_serial * info, int duration)
+static void send_break(struct m68k_serial * info, unsigned int duration)
{
m68328_uart *uart = &uart_addr[info->line];
unsigned long flags;
if (!info->port)
return;
- set_current_state(TASK_INTERRUPTIBLE);
- save_flags(flags);
- cli();
+ local_irq_save(flags);
#ifdef USE_INTS
uart->utx.w |= UTX_SEND_BREAK;
- schedule_timeout(duration);
+ msleep_interruptible(duration);
uart->utx.w &= ~UTX_SEND_BREAK;
#endif
- restore_flags(flags);
+ local_irq_restore(flags);
}
static int rs_ioctl(struct tty_struct *tty, struct file * file,
return retval;
tty_wait_until_sent(tty, 0);
if (!arg)
- send_break(info, HZ/4); /* 1/4 second */
+ send_break(info, 250); /* 1/4 second */
return 0;
case TCSBRKP: /* support for POSIX tcsendbreak() */
retval = tty_check_change(tty);
if (retval)
return retval;
tty_wait_until_sent(tty, 0);
- send_break(info, arg ? arg*(HZ/10) : HZ/4);
+ send_break(info, arg ? arg*(100) : 250);
return 0;
case TIOCGSOFTCAR:
error = put_user(C_CLOCAL(tty) ? 1 : 0,
(struct serial_struct *) arg);
case TIOCSERGETLSR: /* Get line status register */
if (access_ok(VERIFY_WRITE, (void *) arg,
- sizeof(unsigned int));
+ sizeof(unsigned int)))
return get_lsr_info(info, (unsigned int *) arg);
return -EFAULT;
case TIOCSERGSTRUCT:
return 0;
}
-static void rs_set_termios(struct tty_struct *tty, struct termios *old_termios)
+static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
{
struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
if (!info || serial_paranoia_check(info, tty->name, "rs_close"))
return;
- save_flags(flags); cli();
+ local_irq_save(flags);
if (tty_hung_up_p(filp)) {
- restore_flags(flags);
+ local_irq_restore(flags);
return;
}
info->count = 0;
}
if (info->count) {
- restore_flags(flags);
+ local_irq_restore(flags);
return;
}
info->flags |= S_CLOSING;
}
info->flags &= ~(S_NORMAL_ACTIVE|S_CLOSING);
wake_up_interruptible(&info->close_wait);
- restore_flags(flags);
+ local_irq_restore(flags);
}
/*
info->count--;
info->blocked_open++;
while (1) {
- cli();
+ local_irq_disable();
m68k_rtsdtr(info, 1);
- sti();
+ local_irq_enable();
current->state = TASK_INTERRUPTIBLE;
if (tty_hung_up_p(filp) ||
!(info->flags & S_INITIALIZED)) {
printk("MC68328 serial driver version 1.00\n");
}
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_LEGACY
/* Serial Power management
* The console (currently fixed at line 0) is a special case for power
* management because the kernel is so chatty. The console will be
struct m68k_serial *info = &m68k_soft[0];
startup(info);
}
-#endif
+#endif /* CONFIG_PM_LEGACY */
-static struct tty_operations rs_ops = {
+static const struct tty_operations rs_ops = {
.open = rs_open,
.close = rs_close,
.write = rs_write,
return -ENOMEM;
}
- save_flags(flags); cli();
+ local_irq_save(flags);
for(i=0;i<NR_PORTS;i++) {
IRQ_FLG_STD,
"M68328_UART", NULL))
panic("Unable to attach 68328 serial interrupt\n");
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_LEGACY
serial_pm[i] = pm_register(PM_SYS_DEV, PM_SYS_COM, serial_pm_callback);
if (serial_pm[i])
serial_pm[i]->data = info;
#endif
}
- restore_flags(flags);
+ local_irq_restore(flags);
return 0;
}
-
-
-/*
- * register_serial and unregister_serial allows for serial ports to be
- * configured at run-time, to support PCMCIA modems.
- */
-/* SPARC: Unused at this time, just here to make things link. */
-int register_serial(struct serial_struct *req)
-{
- return -1;
-}
-
-void unregister_serial(int line)
-{
- return;
-}
-
module_init(rs68328_init);