--- /dev/null
+/*
+ * drivers/serial/mpsc.c
+ *
+ * Generic driver for the MPSC (UART mode) on Marvell parts (e.g., GT64240,
+ * GT64260, MV64340, MV64360, GT96100, ... ).
+ *
+ * Author: Mark A. Greer <mgreer@mvista.com>
+ *
+ * Based on an old MPSC driver that was in the linuxppc tree. It appears to
+ * have been created by Chris Zankel (formerly of MontaVista) but there
+ * is no proper Copyright so I'm not sure. Apparently, parts were also
+ * taken from PPCBoot (now U-Boot). Also based on drivers/serial/8250.c
+ * by Russell King.
+ *
+ * 2004 (c) MontaVista, Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+/*
+ * The MPSC interface is much like a typical network controller's interface.
+ * That is, you set up separate rings of descriptors for transmitting and
+ * receiving data. There is also a pool of buffers with (one buffer per
+ * descriptor) that incoming data are dma'd into or outgoing data are dma'd
+ * out of.
+ *
+ * The MPSC requires two other controllers to be able to work. The Baud Rate
+ * Generator (BRG) provides a clock at programmable frequencies which determines
+ * the baud rate. The Serial DMA Controller (SDMA) takes incoming data from the
+ * MPSC and DMA's it into memory or DMA's outgoing data and passes it to the
+ * MPSC. It is actually the SDMA interrupt that the driver uses to keep the
+ * transmit and receive "engines" going (i.e., indicate data has been
+ * transmitted or received).
+ *
+ * NOTES:
+ *
+ * 1) Some chips have an erratum where several regs cannot be
+ * read. To work around that, we keep a local copy of those regs in
+ * 'mpsc_port_info'.
+ *
+ * 2) Some chips have an erratum where the ctlr will hang when the SDMA ctlr
+ * accesses system mem with coherency enabled. For that reason, the driver
+ * assumes that coherency for that ctlr has been disabled. This means
+ * that when in a cache coherent system, the driver has to manually manage
+ * the data cache on the areas that it touches because the dma_* macro are
+ * basically no-ops.
+ *
+ * 3) There is an erratum (on PPC) where you can't use the instruction to do
+ * a DMA_TO_DEVICE/cache clean so DMA_BIDIRECTIONAL/flushes are used in places
+ * where a DMA_TO_DEVICE/clean would have [otherwise] sufficed.
+ *
+ * 4) AFAICT, hardware flow control isn't supported by the controller --MAG.
+ */
+
+#include "mpsc.h"
+
+/*
+ * Define how this driver is known to the outside (we've been assigned a
+ * range on the "Low-density serial ports" major).
+ */
+#define MPSC_MAJOR 204
+#define MPSC_MINOR_START 44
+#define MPSC_DRIVER_NAME "MPSC"
+#define MPSC_DEVFS_NAME "ttymm/"
+#define MPSC_DEV_NAME "ttyMM"
+#define MPSC_VERSION "1.00"
+
+static struct mpsc_port_info mpsc_ports[MPSC_NUM_CTLRS];
+static struct mpsc_shared_regs mpsc_shared_regs;
+
+/*
+ ******************************************************************************
+ *
+ * Baud Rate Generator Routines (BRG)
+ *
+ ******************************************************************************
+ */
+static void
+mpsc_brg_init(struct mpsc_port_info *pi, u32 clk_src)
+{
+ u32 v;
+
+ v = (pi->mirror_regs) ? pi->BRG_BCR_m : readl(pi->brg_base + BRG_BCR);
+ v = (v & ~(0xf << 18)) | ((clk_src & 0xf) << 18);
+
+ if (pi->brg_can_tune)
+ v &= ~(1 << 25);
+
+ if (pi->mirror_regs)
+ pi->BRG_BCR_m = v;
+ writel(v, pi->brg_base + BRG_BCR);
+
+ writel(readl(pi->brg_base + BRG_BTR) & 0xffff0000,
+ pi->brg_base + BRG_BTR);
+ return;
+}
+
+static void
+mpsc_brg_enable(struct mpsc_port_info *pi)
+{
+ u32 v;
+
+ v = (pi->mirror_regs) ? pi->BRG_BCR_m : readl(pi->brg_base + BRG_BCR);
+ v |= (1 << 16);
+
+ if (pi->mirror_regs)
+ pi->BRG_BCR_m = v;
+ writel(v, pi->brg_base + BRG_BCR);
+ return;
+}
+
+static void
+mpsc_brg_disable(struct mpsc_port_info *pi)
+{
+ u32 v;
+
+ v = (pi->mirror_regs) ? pi->BRG_BCR_m : readl(pi->brg_base + BRG_BCR);
+ v &= ~(1 << 16);
+
+ if (pi->mirror_regs)
+ pi->BRG_BCR_m = v;
+ writel(v, pi->brg_base + BRG_BCR);
+ return;
+}
+
+static inline void
+mpsc_set_baudrate(struct mpsc_port_info *pi, u32 baud)
+{
+ /*
+ * To set the baud, we adjust the CDV field in the BRG_BCR reg.
+ * From manual: Baud = clk / ((CDV+1)*2) ==> CDV = (clk / (baud*2)) - 1.
+ * However, the input clock is divided by 16 in the MPSC b/c of how
+ * 'MPSC_MMCRH' was set up so we have to divide the 'clk' used in our
+ * calculation by 16 to account for that. So the real calculation
+ * that accounts for the way the mpsc is set up is:
+ * CDV = (clk / (baud*2*16)) - 1 ==> CDV = (clk / (baud << 5)) - 1.
+ */
+ u32 cdv = (pi->port.uartclk / (baud << 5)) - 1;
+ u32 v;
+
+ mpsc_brg_disable(pi);
+ v = (pi->mirror_regs) ? pi->BRG_BCR_m : readl(pi->brg_base + BRG_BCR);
+ v = (v & 0xffff0000) | (cdv & 0xffff);
+
+ if (pi->mirror_regs)
+ pi->BRG_BCR_m = v;
+ writel(v, pi->brg_base + BRG_BCR);
+ mpsc_brg_enable(pi);
+
+ return;
+}
+
+/*
+ ******************************************************************************
+ *
+ * Serial DMA Routines (SDMA)
+ *
+ ******************************************************************************
+ */
+
+static void
+mpsc_sdma_burstsize(struct mpsc_port_info *pi, u32 burst_size)
+{
+ u32 v;
+
+ pr_debug("mpsc_sdma_burstsize[%d]: burst_size: %d\n",
+ pi->port.line, burst_size);
+
+ burst_size >>= 3; /* Divide by 8 b/c reg values are 8-byte chunks */
+
+ if (burst_size < 2)
+ v = 0x0; /* 1 64-bit word */
+ else if (burst_size < 4)
+ v = 0x1; /* 2 64-bit words */
+ else if (burst_size < 8)
+ v = 0x2; /* 4 64-bit words */
+ else
+ v = 0x3; /* 8 64-bit words */
+
+ writel((readl(pi->sdma_base + SDMA_SDC) & (0x3 << 12)) | (v << 12),
+ pi->sdma_base + SDMA_SDC);
+ return;
+}
+
+static void
+mpsc_sdma_init(struct mpsc_port_info *pi, u32 burst_size)
+{
+ pr_debug("mpsc_sdma_init[%d]: burst_size: %d\n", pi->port.line,
+ burst_size);
+
+ writel((readl(pi->sdma_base + SDMA_SDC) & 0x3ff) | 0x03f,
+ pi->sdma_base + SDMA_SDC);
+ mpsc_sdma_burstsize(pi, burst_size);
+ return;
+}
+
+static inline u32
+mpsc_sdma_intr_mask(struct mpsc_port_info *pi, u32 mask)
+{
+ u32 old, v;
+
+ pr_debug("mpsc_sdma_intr_mask[%d]: mask: 0x%x\n", pi->port.line, mask);
+
+ old = v = (pi->mirror_regs) ? pi->shared_regs->SDMA_INTR_MASK_m :
+ readl(pi->shared_regs->sdma_intr_base + SDMA_INTR_MASK);
+
+ mask &= 0xf;
+ if (pi->port.line)
+ mask <<= 8;
+ v &= ~mask;
+
+ if (pi->mirror_regs)
+ pi->shared_regs->SDMA_INTR_MASK_m = v;
+ writel(v, pi->shared_regs->sdma_intr_base + SDMA_INTR_MASK);
+
+ if (pi->port.line)
+ old >>= 8;
+ return old & 0xf;
+}
+
+static inline void
+mpsc_sdma_intr_unmask(struct mpsc_port_info *pi, u32 mask)
+{
+ u32 v;
+
+ pr_debug("mpsc_sdma_intr_unmask[%d]: mask: 0x%x\n", pi->port.line,mask);
+
+ v = (pi->mirror_regs) ? pi->shared_regs->SDMA_INTR_MASK_m :
+ readl(pi->shared_regs->sdma_intr_base + SDMA_INTR_MASK);
+
+ mask &= 0xf;
+ if (pi->port.line)
+ mask <<= 8;
+ v |= mask;
+
+ if (pi->mirror_regs)
+ pi->shared_regs->SDMA_INTR_MASK_m = v;
+ writel(v, pi->shared_regs->sdma_intr_base + SDMA_INTR_MASK);
+ return;
+}
+
+static inline void
+mpsc_sdma_intr_ack(struct mpsc_port_info *pi)
+{
+ pr_debug("mpsc_sdma_intr_ack[%d]: Acknowledging IRQ\n", pi->port.line);
+
+ if (pi->mirror_regs)
+ pi->shared_regs->SDMA_INTR_CAUSE_m = 0;
+ writel(0, pi->shared_regs->sdma_intr_base + SDMA_INTR_CAUSE);
+ return;
+}
+
+static inline void
+mpsc_sdma_set_rx_ring(struct mpsc_port_info *pi, struct mpsc_rx_desc *rxre_p)
+{
+ pr_debug("mpsc_sdma_set_rx_ring[%d]: rxre_p: 0x%x\n",
+ pi->port.line, (u32) rxre_p);
+
+ writel((u32)rxre_p, pi->sdma_base + SDMA_SCRDP);
+ return;
+}
+
+static inline void
+mpsc_sdma_set_tx_ring(struct mpsc_port_info *pi, struct mpsc_tx_desc *txre_p)
+{
+ writel((u32)txre_p, pi->sdma_base + SDMA_SFTDP);
+ writel((u32)txre_p, pi->sdma_base + SDMA_SCTDP);
+ return;
+}
+
+static inline void
+mpsc_sdma_cmd(struct mpsc_port_info *pi, u32 val)
+{
+ u32 v;
+
+ v = readl(pi->sdma_base + SDMA_SDCM);
+ if (val)
+ v |= val;
+ else
+ v = 0;
+ wmb();
+ writel(v, pi->sdma_base + SDMA_SDCM);
+ wmb();
+ return;
+}
+
+static inline uint
+mpsc_sdma_tx_active(struct mpsc_port_info *pi)
+{
+ return readl(pi->sdma_base + SDMA_SDCM) & SDMA_SDCM_TXD;
+}
+
+static inline void
+mpsc_sdma_start_tx(struct mpsc_port_info *pi)
+{
+ struct mpsc_tx_desc *txre, *txre_p;
+
+ /* If tx isn't running & there's a desc ready to go, start it */
+ if (!mpsc_sdma_tx_active(pi)) {
+ txre = (struct mpsc_tx_desc *)(pi->txr +
+ (pi->txr_tail * MPSC_TXRE_SIZE));
+ dma_cache_sync((void *) txre, MPSC_TXRE_SIZE, DMA_FROM_DEVICE);
+#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
+ if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */
+ invalidate_dcache_range((ulong)txre,
+ (ulong)txre + MPSC_TXRE_SIZE);
+#endif
+
+ if (be32_to_cpu(txre->cmdstat) & SDMA_DESC_CMDSTAT_O) {
+ txre_p = (struct mpsc_tx_desc *)(pi->txr_p +
+ (pi->txr_tail *
+ MPSC_TXRE_SIZE));
+
+ mpsc_sdma_set_tx_ring(pi, txre_p);
+ mpsc_sdma_cmd(pi, SDMA_SDCM_STD | SDMA_SDCM_TXD);
+ }
+ }
+
+ return;
+}
+
+static inline void
+mpsc_sdma_stop(struct mpsc_port_info *pi)
+{
+ pr_debug("mpsc_sdma_stop[%d]: Stopping SDMA\n", pi->port.line);
+
+ /* Abort any SDMA transfers */
+ mpsc_sdma_cmd(pi, 0);
+ mpsc_sdma_cmd(pi, SDMA_SDCM_AR | SDMA_SDCM_AT);
+
+ /* Clear the SDMA current and first TX and RX pointers */
+ mpsc_sdma_set_tx_ring(pi, 0);
+ mpsc_sdma_set_rx_ring(pi, 0);
+
+ /* Disable interrupts */
+ mpsc_sdma_intr_mask(pi, 0xf);
+ mpsc_sdma_intr_ack(pi);
+
+ return;
+}
+
+/*
+ ******************************************************************************
+ *
+ * Multi-Protocol Serial Controller Routines (MPSC)
+ *
+ ******************************************************************************
+ */
+
+static void
+mpsc_hw_init(struct mpsc_port_info *pi)
+{
+ u32 v;
+
+ pr_debug("mpsc_hw_init[%d]: Initializing hardware\n", pi->port.line);
+
+ /* Set up clock routing */
+ if (pi->mirror_regs) {
+ v = pi->shared_regs->MPSC_MRR_m;
+ v &= ~0x1c7;
+ pi->shared_regs->MPSC_MRR_m = v;
+ writel(v, pi->shared_regs->mpsc_routing_base + MPSC_MRR);
+
+ v = pi->shared_regs->MPSC_RCRR_m;
+ v = (v & ~0xf0f) | 0x100;
+ pi->shared_regs->MPSC_RCRR_m = v;
+ writel(v, pi->shared_regs->mpsc_routing_base + MPSC_RCRR);
+
+ v = pi->shared_regs->MPSC_TCRR_m;
+ v = (v & ~0xf0f) | 0x100;
+ pi->shared_regs->MPSC_TCRR_m = v;
+ writel(v, pi->shared_regs->mpsc_routing_base + MPSC_TCRR);
+ }
+ else {
+ v = readl(pi->shared_regs->mpsc_routing_base + MPSC_MRR);
+ v &= ~0x1c7;
+ writel(v, pi->shared_regs->mpsc_routing_base + MPSC_MRR);
+
+ v = readl(pi->shared_regs->mpsc_routing_base + MPSC_RCRR);
+ v = (v & ~0xf0f) | 0x100;
+ writel(v, pi->shared_regs->mpsc_routing_base + MPSC_RCRR);
+
+ v = readl(pi->shared_regs->mpsc_routing_base + MPSC_TCRR);
+ v = (v & ~0xf0f) | 0x100;
+ writel(v, pi->shared_regs->mpsc_routing_base + MPSC_TCRR);
+ }
+
+ /* Put MPSC in UART mode & enabel Tx/Rx egines */
+ writel(0x000004c4, pi->mpsc_base + MPSC_MMCRL);
+
+ /* No preamble, 16x divider, low-latency, */
+ writel(0x04400400, pi->mpsc_base + MPSC_MMCRH);
+
+ if (pi->mirror_regs) {
+ pi->MPSC_CHR_1_m = 0;
+ pi->MPSC_CHR_2_m = 0;
+ }
+ writel(0, pi->mpsc_base + MPSC_CHR_1);
+ writel(0, pi->mpsc_base + MPSC_CHR_2);
+ writel(pi->mpsc_max_idle, pi->mpsc_base + MPSC_CHR_3);
+ writel(0, pi->mpsc_base + MPSC_CHR_4);
+ writel(0, pi->mpsc_base + MPSC_CHR_5);
+ writel(0, pi->mpsc_base + MPSC_CHR_6);
+ writel(0, pi->mpsc_base + MPSC_CHR_7);
+ writel(0, pi->mpsc_base + MPSC_CHR_8);
+ writel(0, pi->mpsc_base + MPSC_CHR_9);
+ writel(0, pi->mpsc_base + MPSC_CHR_10);
+
+ return;
+}
+
+static inline void
+mpsc_enter_hunt(struct mpsc_port_info *pi)
+{
+ pr_debug("mpsc_enter_hunt[%d]: Hunting...\n", pi->port.line);
+
+ if (pi->mirror_regs) {
+ writel(pi->MPSC_CHR_2_m | MPSC_CHR_2_EH,
+ pi->mpsc_base + MPSC_CHR_2);
+ /* Erratum prevents reading CHR_2 so just delay for a while */
+ udelay(100);
+ }
+ else {
+ writel(readl(pi->mpsc_base + MPSC_CHR_2) | MPSC_CHR_2_EH,
+ pi->mpsc_base + MPSC_CHR_2);
+
+ while (readl(pi->mpsc_base + MPSC_CHR_2) & MPSC_CHR_2_EH)
+ udelay(10);
+ }
+
+ return;
+}
+
+static inline void
+mpsc_freeze(struct mpsc_port_info *pi)
+{
+ u32 v;
+
+ pr_debug("mpsc_freeze[%d]: Freezing\n", pi->port.line);
+
+ v = (pi->mirror_regs) ? pi->MPSC_MPCR_m :
+ readl(pi->mpsc_base + MPSC_MPCR);
+ v |= MPSC_MPCR_FRZ;
+
+ if (pi->mirror_regs)
+ pi->MPSC_MPCR_m = v;
+ writel(v, pi->mpsc_base + MPSC_MPCR);
+ return;
+}
+
+static inline void
+mpsc_unfreeze(struct mpsc_port_info *pi)
+{
+ u32 v;
+
+ v = (pi->mirror_regs) ? pi->MPSC_MPCR_m :
+ readl(pi->mpsc_base + MPSC_MPCR);
+ v &= ~MPSC_MPCR_FRZ;
+
+ if (pi->mirror_regs)
+ pi->MPSC_MPCR_m = v;
+ writel(v, pi->mpsc_base + MPSC_MPCR);
+
+ pr_debug("mpsc_unfreeze[%d]: Unfrozen\n", pi->port.line);
+ return;
+}
+
+static inline void
+mpsc_set_char_length(struct mpsc_port_info *pi, u32 len)
+{
+ u32 v;
+
+ pr_debug("mpsc_set_char_length[%d]: char len: %d\n", pi->port.line,len);
+
+ v = (pi->mirror_regs) ? pi->MPSC_MPCR_m :
+ readl(pi->mpsc_base + MPSC_MPCR);
+ v = (v & ~(0x3 << 12)) | ((len & 0x3) << 12);
+
+ if (pi->mirror_regs)
+ pi->MPSC_MPCR_m = v;
+ writel(v, pi->mpsc_base + MPSC_MPCR);
+ return;
+}
+
+static inline void
+mpsc_set_stop_bit_length(struct mpsc_port_info *pi, u32 len)
+{
+ u32 v;
+
+ pr_debug("mpsc_set_stop_bit_length[%d]: stop bits: %d\n",
+ pi->port.line, len);
+
+ v = (pi->mirror_regs) ? pi->MPSC_MPCR_m :
+ readl(pi->mpsc_base + MPSC_MPCR);
+
+ v = (v & ~(1 << 14)) | ((len & 0x1) << 14);
+
+ if (pi->mirror_regs)
+ pi->MPSC_MPCR_m = v;
+ writel(v, pi->mpsc_base + MPSC_MPCR);
+ return;
+}
+
+static inline void
+mpsc_set_parity(struct mpsc_port_info *pi, u32 p)
+{
+ u32 v;
+
+ pr_debug("mpsc_set_parity[%d]: parity bits: 0x%x\n", pi->port.line, p);
+
+ v = (pi->mirror_regs) ? pi->MPSC_CHR_2_m :
+ readl(pi->mpsc_base + MPSC_CHR_2);
+
+ p &= 0x3;
+ v = (v & ~0xc000c) | (p << 18) | (p << 2);
+
+ if (pi->mirror_regs)
+ pi->MPSC_CHR_2_m = v;
+ writel(v, pi->mpsc_base + MPSC_CHR_2);
+ return;
+}
+
+/*
+ ******************************************************************************
+ *
+ * Driver Init Routines
+ *
+ ******************************************************************************
+ */
+
+static void
+mpsc_init_hw(struct mpsc_port_info *pi)
+{
+ pr_debug("mpsc_init_hw[%d]: Initializing\n", pi->port.line);
+
+ mpsc_brg_init(pi, pi->brg_clk_src);
+ mpsc_brg_enable(pi);
+ mpsc_sdma_init(pi, dma_get_cache_alignment()); /* burst a cacheline */
+ mpsc_sdma_stop(pi);
+ mpsc_hw_init(pi);
+
+ return;
+}
+
+static int
+mpsc_alloc_ring_mem(struct mpsc_port_info *pi)
+{
+ int rc = 0;
+ static void mpsc_free_ring_mem(struct mpsc_port_info *pi);
+
+ pr_debug("mpsc_alloc_ring_mem[%d]: Allocating ring mem\n",
+ pi->port.line);
+
+ if (!pi->dma_region) {
+ if (!dma_supported(pi->port.dev, 0xffffffff)) {
+ printk(KERN_ERR "MPSC: Inadequate DMA support\n");
+ rc = -ENXIO;
+ }
+ else if ((pi->dma_region = dma_alloc_noncoherent(pi->port.dev,
+ MPSC_DMA_ALLOC_SIZE, &pi->dma_region_p, GFP_KERNEL))
+ == NULL) {
+
+ printk(KERN_ERR "MPSC: Can't alloc Desc region\n");
+ rc = -ENOMEM;
+ }
+ }
+
+ return rc;
+}
+
+static void
+mpsc_free_ring_mem(struct mpsc_port_info *pi)
+{
+ pr_debug("mpsc_free_ring_mem[%d]: Freeing ring mem\n", pi->port.line);
+
+ if (pi->dma_region) {
+ dma_free_noncoherent(pi->port.dev, MPSC_DMA_ALLOC_SIZE,
+ pi->dma_region, pi->dma_region_p);
+ pi->dma_region = NULL;
+ pi->dma_region_p = (dma_addr_t) NULL;
+ }
+
+ return;
+}
+
+static void
+mpsc_init_rings(struct mpsc_port_info *pi)
+{
+ struct mpsc_rx_desc *rxre;
+ struct mpsc_tx_desc *txre;
+ dma_addr_t dp, dp_p;
+ u8 *bp, *bp_p;
+ int i;
+
+ pr_debug("mpsc_init_rings[%d]: Initializing rings\n", pi->port.line);
+
+ BUG_ON(pi->dma_region == NULL);
+
+ memset(pi->dma_region, 0, MPSC_DMA_ALLOC_SIZE);
+
+ /*
+ * Descriptors & buffers are multiples of cacheline size and must be
+ * cacheline aligned.
+ */
+ dp = ALIGN((u32) pi->dma_region, dma_get_cache_alignment());
+ dp_p = ALIGN((u32) pi->dma_region_p, dma_get_cache_alignment());
+
+ /*
+ * Partition dma region into rx ring descriptor, rx buffers,
+ * tx ring descriptors, and tx buffers.
+ */
+ pi->rxr = dp;
+ pi->rxr_p = dp_p;
+ dp += MPSC_RXR_SIZE;
+ dp_p += MPSC_RXR_SIZE;
+
+ pi->rxb = (u8 *) dp;
+ pi->rxb_p = (u8 *) dp_p;
+ dp += MPSC_RXB_SIZE;
+ dp_p += MPSC_RXB_SIZE;
+
+ pi->rxr_posn = 0;
+
+ pi->txr = dp;
+ pi->txr_p = dp_p;
+ dp += MPSC_TXR_SIZE;
+ dp_p += MPSC_TXR_SIZE;
+
+ pi->txb = (u8 *) dp;
+ pi->txb_p = (u8 *) dp_p;
+
+ pi->txr_head = 0;
+ pi->txr_tail = 0;
+
+ /* Init rx ring descriptors */
+ dp = pi->rxr;
+ dp_p = pi->rxr_p;
+ bp = pi->rxb;
+ bp_p = pi->rxb_p;
+
+ for (i = 0; i < MPSC_RXR_ENTRIES; i++) {
+ rxre = (struct mpsc_rx_desc *)dp;
+
+ rxre->bufsize = cpu_to_be16(MPSC_RXBE_SIZE);
+ rxre->bytecnt = cpu_to_be16(0);
+ rxre->cmdstat = cpu_to_be32(SDMA_DESC_CMDSTAT_O |
+ SDMA_DESC_CMDSTAT_EI |
+ SDMA_DESC_CMDSTAT_F |
+ SDMA_DESC_CMDSTAT_L);
+ rxre->link = cpu_to_be32(dp_p + MPSC_RXRE_SIZE);
+ rxre->buf_ptr = cpu_to_be32(bp_p);
+
+ dp += MPSC_RXRE_SIZE;
+ dp_p += MPSC_RXRE_SIZE;
+ bp += MPSC_RXBE_SIZE;
+ bp_p += MPSC_RXBE_SIZE;
+ }
+ rxre->link = cpu_to_be32(pi->rxr_p); /* Wrap last back to first */
+
+ /* Init tx ring descriptors */
+ dp = pi->txr;
+ dp_p = pi->txr_p;
+ bp = pi->txb;
+ bp_p = pi->txb_p;
+
+ for (i = 0; i < MPSC_TXR_ENTRIES; i++) {
+ txre = (struct mpsc_tx_desc *)dp;
+
+ txre->link = cpu_to_be32(dp_p + MPSC_TXRE_SIZE);
+ txre->buf_ptr = cpu_to_be32(bp_p);
+
+ dp += MPSC_TXRE_SIZE;
+ dp_p += MPSC_TXRE_SIZE;
+ bp += MPSC_TXBE_SIZE;
+ bp_p += MPSC_TXBE_SIZE;
+ }
+ txre->link = cpu_to_be32(pi->txr_p); /* Wrap last back to first */
+
+ dma_cache_sync((void *) pi->dma_region, MPSC_DMA_ALLOC_SIZE,
+ DMA_BIDIRECTIONAL);
+#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
+ if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */
+ flush_dcache_range((ulong)pi->dma_region,
+ (ulong)pi->dma_region + MPSC_DMA_ALLOC_SIZE);
+#endif
+
+ return;
+}
+
+static void
+mpsc_uninit_rings(struct mpsc_port_info *pi)
+{
+ pr_debug("mpsc_uninit_rings[%d]: Uninitializing rings\n",pi->port.line);
+
+ BUG_ON(pi->dma_region == NULL);
+
+ pi->rxr = 0;
+ pi->rxr_p = 0;
+ pi->rxb = NULL;
+ pi->rxb_p = NULL;
+ pi->rxr_posn = 0;
+
+ pi->txr = 0;
+ pi->txr_p = 0;
+ pi->txb = NULL;
+ pi->txb_p = NULL;
+ pi->txr_head = 0;
+ pi->txr_tail = 0;
+
+ return;
+}
+
+static int
+mpsc_make_ready(struct mpsc_port_info *pi)
+{
+ int rc;
+
+ pr_debug("mpsc_make_ready[%d]: Making cltr ready\n", pi->port.line);
+
+ if (!pi->ready) {
+ mpsc_init_hw(pi);
+ if ((rc = mpsc_alloc_ring_mem(pi)))
+ return rc;
+ mpsc_init_rings(pi);
+ pi->ready = 1;
+ }
+
+ return 0;
+}
+
+/*
+ ******************************************************************************
+ *
+ * Interrupt Handling Routines
+ *
+ ******************************************************************************
+ */
+
+static inline int
+mpsc_rx_intr(struct mpsc_port_info *pi, struct pt_regs *regs)
+{
+ struct mpsc_rx_desc *rxre;
+ struct tty_struct *tty = pi->port.info->tty;
+ u32 cmdstat, bytes_in, i;
+ int rc = 0;
+ u8 *bp;
+ char flag = TTY_NORMAL;
+ static void mpsc_start_rx(struct mpsc_port_info *pi);
+
+ pr_debug("mpsc_rx_intr[%d]: Handling Rx intr\n", pi->port.line);
+
+ rxre = (struct mpsc_rx_desc *)(pi->rxr + (pi->rxr_posn*MPSC_RXRE_SIZE));
+
+ dma_cache_sync((void *)rxre, MPSC_RXRE_SIZE, DMA_FROM_DEVICE);
+#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
+ if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */
+ invalidate_dcache_range((ulong)rxre,
+ (ulong)rxre + MPSC_RXRE_SIZE);
+#endif
+
+ /*
+ * Loop through Rx descriptors handling ones that have been completed.
+ */
+ while (!((cmdstat = be32_to_cpu(rxre->cmdstat)) & SDMA_DESC_CMDSTAT_O)){
+ bytes_in = be16_to_cpu(rxre->bytecnt);
+
+ /* Following use of tty struct directly is deprecated */
+ if (unlikely((tty->flip.count + bytes_in) >= TTY_FLIPBUF_SIZE)){
+ if (tty->low_latency)
+ tty_flip_buffer_push(tty);
+ /*
+ * If this failed then we will throw awa the bytes
+ * but mst do so to clear interrupts.
+ */
+ }
+
+ bp = pi->rxb + (pi->rxr_posn * MPSC_RXBE_SIZE);
+ dma_cache_sync((void *) bp, MPSC_RXBE_SIZE, DMA_FROM_DEVICE);
+#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
+ if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */
+ invalidate_dcache_range((ulong)bp,
+ (ulong)bp + MPSC_RXBE_SIZE);
+#endif
+
+ /*
+ * Other than for parity error, the manual provides little
+ * info on what data will be in a frame flagged by any of
+ * these errors. For parity error, it is the last byte in
+ * the buffer that had the error. As for the rest, I guess
+ * we'll assume there is no data in the buffer.
+ * If there is...it gets lost.
+ */
+ if (unlikely(cmdstat & (SDMA_DESC_CMDSTAT_BR |
+ SDMA_DESC_CMDSTAT_FR | SDMA_DESC_CMDSTAT_OR))) {
+
+ pi->port.icount.rx++;
+
+ if (cmdstat & SDMA_DESC_CMDSTAT_BR) { /* Break */
+ pi->port.icount.brk++;
+
+ if (uart_handle_break(&pi->port))
+ goto next_frame;
+ }
+ else if (cmdstat & SDMA_DESC_CMDSTAT_FR)/* Framing */
+ pi->port.icount.frame++;
+ else if (cmdstat & SDMA_DESC_CMDSTAT_OR) /* Overrun */
+ pi->port.icount.overrun++;
+
+ cmdstat &= pi->port.read_status_mask;
+
+ if (cmdstat & SDMA_DESC_CMDSTAT_BR)
+ flag = TTY_BREAK;
+ else if (cmdstat & SDMA_DESC_CMDSTAT_FR)
+ flag = TTY_FRAME;
+ else if (cmdstat & SDMA_DESC_CMDSTAT_OR)
+ flag = TTY_OVERRUN;
+ else if (cmdstat & SDMA_DESC_CMDSTAT_PE)
+ flag = TTY_PARITY;
+ }
+
+ if (uart_handle_sysrq_char(&pi->port, *bp, regs)) {
+ bp++;
+ bytes_in--;
+ goto next_frame;
+ }
+
+ if ((unlikely(cmdstat & (SDMA_DESC_CMDSTAT_BR |
+ SDMA_DESC_CMDSTAT_FR | SDMA_DESC_CMDSTAT_OR))) &&
+ !(cmdstat & pi->port.ignore_status_mask))
+
+ tty_insert_flip_char(tty, *bp, flag);
+ else {
+ for (i=0; i<bytes_in; i++)
+ tty_insert_flip_char(tty, *bp++, TTY_NORMAL);
+
+ pi->port.icount.rx += bytes_in;
+ }
+
+next_frame:
+ rxre->bytecnt = cpu_to_be16(0);
+ wmb();
+ rxre->cmdstat = cpu_to_be32(SDMA_DESC_CMDSTAT_O |
+ SDMA_DESC_CMDSTAT_EI |
+ SDMA_DESC_CMDSTAT_F |
+ SDMA_DESC_CMDSTAT_L);
+ wmb();
+ dma_cache_sync((void *)rxre, MPSC_RXRE_SIZE, DMA_BIDIRECTIONAL);
+#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
+ if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */
+ flush_dcache_range((ulong)rxre,
+ (ulong)rxre + MPSC_RXRE_SIZE);
+#endif
+
+ /* Advance to next descriptor */
+ pi->rxr_posn = (pi->rxr_posn + 1) & (MPSC_RXR_ENTRIES - 1);
+ rxre = (struct mpsc_rx_desc *)(pi->rxr +
+ (pi->rxr_posn * MPSC_RXRE_SIZE));
+ dma_cache_sync((void *)rxre, MPSC_RXRE_SIZE, DMA_FROM_DEVICE);
+#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
+ if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */
+ invalidate_dcache_range((ulong)rxre,
+ (ulong)rxre + MPSC_RXRE_SIZE);
+#endif
+
+ rc = 1;
+ }
+
+ /* Restart rx engine, if its stopped */
+ if ((readl(pi->sdma_base + SDMA_SDCM) & SDMA_SDCM_ERD) == 0)
+ mpsc_start_rx(pi);
+
+ tty_flip_buffer_push(tty);
+ return rc;
+}
+
+static inline void
+mpsc_setup_tx_desc(struct mpsc_port_info *pi, u32 count, u32 intr)
+{
+ struct mpsc_tx_desc *txre;
+
+ txre = (struct mpsc_tx_desc *)(pi->txr +
+ (pi->txr_head * MPSC_TXRE_SIZE));
+
+ txre->bytecnt = cpu_to_be16(count);
+ txre->shadow = txre->bytecnt;
+ wmb(); /* ensure cmdstat is last field updated */
+ txre->cmdstat = cpu_to_be32(SDMA_DESC_CMDSTAT_O | SDMA_DESC_CMDSTAT_F |
+ SDMA_DESC_CMDSTAT_L | ((intr) ?
+ SDMA_DESC_CMDSTAT_EI
+ : 0));
+ wmb();
+ dma_cache_sync((void *) txre, MPSC_TXRE_SIZE, DMA_BIDIRECTIONAL);
+#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
+ if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */
+ flush_dcache_range((ulong)txre,
+ (ulong)txre + MPSC_TXRE_SIZE);
+#endif
+
+ return;
+}
+
+static inline void
+mpsc_copy_tx_data(struct mpsc_port_info *pi)
+{
+ struct circ_buf *xmit = &pi->port.info->xmit;
+ u8 *bp;
+ u32 i;
+
+ /* Make sure the desc ring isn't full */
+ while (CIRC_CNT(pi->txr_head, pi->txr_tail, MPSC_TXR_ENTRIES) <
+ (MPSC_TXR_ENTRIES - 1)) {
+ if (pi->port.x_char) {
+ /*
+ * Ideally, we should use the TCS field in
+ * CHR_1 to put the x_char out immediately but
+ * errata prevents us from being able to read
+ * CHR_2 to know that its safe to write to
+ * CHR_1. Instead, just put it in-band with
+ * all the other Tx data.
+ */
+ bp = pi->txb + (pi->txr_head * MPSC_TXBE_SIZE);
+ *bp = pi->port.x_char;
+ pi->port.x_char = 0;
+ i = 1;
+ }
+ else if (!uart_circ_empty(xmit) && !uart_tx_stopped(&pi->port)){
+ i = min((u32) MPSC_TXBE_SIZE,
+ (u32) uart_circ_chars_pending(xmit));
+ i = min(i, (u32) CIRC_CNT_TO_END(xmit->head, xmit->tail,
+ UART_XMIT_SIZE));
+ bp = pi->txb + (pi->txr_head * MPSC_TXBE_SIZE);
+ memcpy(bp, &xmit->buf[xmit->tail], i);
+ xmit->tail = (xmit->tail + i) & (UART_XMIT_SIZE - 1);
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&pi->port);
+ }
+ else /* All tx data copied into ring bufs */
+ return;
+
+ dma_cache_sync((void *) bp, MPSC_TXBE_SIZE, DMA_BIDIRECTIONAL);
+#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
+ if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */
+ flush_dcache_range((ulong)bp,
+ (ulong)bp + MPSC_TXBE_SIZE);
+#endif
+ mpsc_setup_tx_desc(pi, i, 1);
+
+ /* Advance to next descriptor */
+ pi->txr_head = (pi->txr_head + 1) & (MPSC_TXR_ENTRIES - 1);
+ }
+
+ return;
+}
+
+static inline int
+mpsc_tx_intr(struct mpsc_port_info *pi)
+{
+ struct mpsc_tx_desc *txre;
+ int rc = 0;
+
+ if (!mpsc_sdma_tx_active(pi)) {
+ txre = (struct mpsc_tx_desc *)(pi->txr +
+ (pi->txr_tail * MPSC_TXRE_SIZE));
+
+ dma_cache_sync((void *) txre, MPSC_TXRE_SIZE, DMA_FROM_DEVICE);
+#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
+ if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */
+ invalidate_dcache_range((ulong)txre,
+ (ulong)txre + MPSC_TXRE_SIZE);
+#endif
+
+ while (!(be32_to_cpu(txre->cmdstat) & SDMA_DESC_CMDSTAT_O)) {
+ rc = 1;
+ pi->port.icount.tx += be16_to_cpu(txre->bytecnt);
+ pi->txr_tail = (pi->txr_tail+1) & (MPSC_TXR_ENTRIES-1);
+
+ /* If no more data to tx, fall out of loop */
+ if (pi->txr_head == pi->txr_tail)
+ break;
+
+ txre = (struct mpsc_tx_desc *)(pi->txr +
+ (pi->txr_tail * MPSC_TXRE_SIZE));
+ dma_cache_sync((void *) txre, MPSC_TXRE_SIZE,
+ DMA_FROM_DEVICE);
+#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
+ if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */
+ invalidate_dcache_range((ulong)txre,
+ (ulong)txre + MPSC_TXRE_SIZE);
+#endif
+ }
+
+ mpsc_copy_tx_data(pi);
+ mpsc_sdma_start_tx(pi); /* start next desc if ready */
+ }
+
+ return rc;
+}
+
+/*
+ * This is the driver's interrupt handler. To avoid a race, we first clear
+ * the interrupt, then handle any completed Rx/Tx descriptors. When done
+ * handling those descriptors, we restart the Rx/Tx engines if they're stopped.
+ */
+static irqreturn_t
+mpsc_sdma_intr(int irq, void *dev_id, struct pt_regs *regs)
+{
+ struct mpsc_port_info *pi = dev_id;
+ ulong iflags;
+ int rc = IRQ_NONE;
+
+ pr_debug("mpsc_sdma_intr[%d]: SDMA Interrupt Received\n",pi->port.line);
+
+ spin_lock_irqsave(&pi->port.lock, iflags);
+ mpsc_sdma_intr_ack(pi);
+ if (mpsc_rx_intr(pi, regs))
+ rc = IRQ_HANDLED;
+ if (mpsc_tx_intr(pi))
+ rc = IRQ_HANDLED;
+ spin_unlock_irqrestore(&pi->port.lock, iflags);
+
+ pr_debug("mpsc_sdma_intr[%d]: SDMA Interrupt Handled\n", pi->port.line);
+ return rc;
+}
+
+/*
+ ******************************************************************************
+ *
+ * serial_core.c Interface routines
+ *
+ ******************************************************************************
+ */
+static uint
+mpsc_tx_empty(struct uart_port *port)
+{
+ struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+ ulong iflags;
+ uint rc;
+
+ spin_lock_irqsave(&pi->port.lock, iflags);
+ rc = mpsc_sdma_tx_active(pi) ? 0 : TIOCSER_TEMT;
+ spin_unlock_irqrestore(&pi->port.lock, iflags);
+
+ return rc;
+}
+
+static void
+mpsc_set_mctrl(struct uart_port *port, uint mctrl)
+{
+ /* Have no way to set modem control lines AFAICT */
+ return;
+}
+
+static uint
+mpsc_get_mctrl(struct uart_port *port)
+{
+ struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+ u32 mflags, status;
+ ulong iflags;
+
+ spin_lock_irqsave(&pi->port.lock, iflags);
+ status = (pi->mirror_regs) ? pi->MPSC_CHR_10_m :
+ readl(pi->mpsc_base + MPSC_CHR_10);
+ spin_unlock_irqrestore(&pi->port.lock, iflags);
+
+ mflags = 0;
+ if (status & 0x1)
+ mflags |= TIOCM_CTS;
+ if (status & 0x2)
+ mflags |= TIOCM_CAR;
+
+ return mflags | TIOCM_DSR; /* No way to tell if DSR asserted */
+}
+
+static void
+mpsc_stop_tx(struct uart_port *port, uint tty_start)
+{
+ struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+
+ pr_debug("mpsc_stop_tx[%d]: tty_start: %d\n", port->line, tty_start);
+
+ mpsc_freeze(pi);
+ return;
+}
+
+static void
+mpsc_start_tx(struct uart_port *port, uint tty_start)
+{
+ struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+
+ mpsc_unfreeze(pi);
+ mpsc_copy_tx_data(pi);
+ mpsc_sdma_start_tx(pi);
+
+ pr_debug("mpsc_start_tx[%d]: tty_start: %d\n", port->line, tty_start);
+ return;
+}
+
+static void
+mpsc_start_rx(struct mpsc_port_info *pi)
+{
+ pr_debug("mpsc_start_rx[%d]: Starting...\n", pi->port.line);
+
+ if (pi->rcv_data) {
+ mpsc_enter_hunt(pi);
+ mpsc_sdma_cmd(pi, SDMA_SDCM_ERD);
+ }
+ return;
+}
+
+static void
+mpsc_stop_rx(struct uart_port *port)
+{
+ struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+
+ pr_debug("mpsc_stop_rx[%d]: Stopping...\n", port->line);
+
+ mpsc_sdma_cmd(pi, SDMA_SDCM_AR);
+ return;
+}
+
+static void
+mpsc_enable_ms(struct uart_port *port)
+{
+ return; /* Not supported */
+}
+
+static void
+mpsc_break_ctl(struct uart_port *port, int ctl)
+{
+ struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+ ulong flags;
+ u32 v;
+
+ v = ctl ? 0x00ff0000 : 0;
+
+ spin_lock_irqsave(&pi->port.lock, flags);
+ if (pi->mirror_regs)
+ pi->MPSC_CHR_1_m = v;
+ writel(v, pi->mpsc_base + MPSC_CHR_1);
+ spin_unlock_irqrestore(&pi->port.lock, flags);
+
+ return;
+}
+
+static int
+mpsc_startup(struct uart_port *port)
+{
+ struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+ u32 flag = 0;
+ int rc;
+
+ pr_debug("mpsc_startup[%d]: Starting up MPSC, irq: %d\n",
+ port->line, pi->port.irq);
+
+ if ((rc = mpsc_make_ready(pi)) == 0) {
+ /* Setup IRQ handler */
+ mpsc_sdma_intr_ack(pi);
+
+ /* If irq's are shared, need to set flag */
+ if (mpsc_ports[0].port.irq == mpsc_ports[1].port.irq)
+ flag = SA_SHIRQ;
+
+ if (request_irq(pi->port.irq, mpsc_sdma_intr, flag,
+ "mpsc/sdma", pi))
+ printk(KERN_ERR "MPSC: Can't get SDMA IRQ %d\n",
+ pi->port.irq);
+
+ mpsc_sdma_intr_unmask(pi, 0xf);
+ mpsc_sdma_set_rx_ring(pi, (struct mpsc_rx_desc *)(pi->rxr_p +
+ (pi->rxr_posn * MPSC_RXRE_SIZE)));
+ }
+
+ return rc;
+}
+
+static void
+mpsc_shutdown(struct uart_port *port)
+{
+ struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+ static void mpsc_release_port(struct uart_port *port);
+
+ pr_debug("mpsc_shutdown[%d]: Shutting down MPSC\n", port->line);
+
+ mpsc_sdma_stop(pi);
+ free_irq(pi->port.irq, pi);
+ return;
+}
+
+static void
+mpsc_set_termios(struct uart_port *port, struct termios *termios,
+ struct termios *old)
+{
+ struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+ u32 baud;
+ ulong flags;
+ u32 chr_bits, stop_bits, par;
+
+ pi->c_iflag = termios->c_iflag;
+ pi->c_cflag = termios->c_cflag;
+
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ chr_bits = MPSC_MPCR_CL_5;
+ break;
+ case CS6:
+ chr_bits = MPSC_MPCR_CL_6;
+ break;
+ case CS7:
+ chr_bits = MPSC_MPCR_CL_7;
+ break;
+ case CS8:
+ default:
+ chr_bits = MPSC_MPCR_CL_8;
+ break;
+ }
+
+ if (termios->c_cflag & CSTOPB)
+ stop_bits = MPSC_MPCR_SBL_2;
+ else
+ stop_bits = MPSC_MPCR_SBL_1;
+
+ par = MPSC_CHR_2_PAR_EVEN;
+ if (termios->c_cflag & PARENB)
+ if (termios->c_cflag & PARODD)
+ par = MPSC_CHR_2_PAR_ODD;
+#ifdef CMSPAR
+ if (termios->c_cflag & CMSPAR) {
+ if (termios->c_cflag & PARODD)
+ par = MPSC_CHR_2_PAR_MARK;
+ else
+ par = MPSC_CHR_2_PAR_SPACE;
+ }
+#endif
+
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk);
+
+ spin_lock_irqsave(&pi->port.lock, flags);
+
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ mpsc_set_char_length(pi, chr_bits);
+ mpsc_set_stop_bit_length(pi, stop_bits);
+ mpsc_set_parity(pi, par);
+ mpsc_set_baudrate(pi, baud);
+
+ /* Characters/events to read */
+ pi->rcv_data = 1;
+ pi->port.read_status_mask = SDMA_DESC_CMDSTAT_OR;
+
+ if (termios->c_iflag & INPCK)
+ pi->port.read_status_mask |= SDMA_DESC_CMDSTAT_PE |
+ SDMA_DESC_CMDSTAT_FR;
+
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ pi->port.read_status_mask |= SDMA_DESC_CMDSTAT_BR;
+
+ /* Characters/events to ignore */
+ pi->port.ignore_status_mask = 0;
+
+ if (termios->c_iflag & IGNPAR)
+ pi->port.ignore_status_mask |= SDMA_DESC_CMDSTAT_PE |
+ SDMA_DESC_CMDSTAT_FR;
+
+ if (termios->c_iflag & IGNBRK) {
+ pi->port.ignore_status_mask |= SDMA_DESC_CMDSTAT_BR;
+
+ if (termios->c_iflag & IGNPAR)
+ pi->port.ignore_status_mask |= SDMA_DESC_CMDSTAT_OR;
+ }
+
+ /* Ignore all chars if CREAD not set */
+ if (!(termios->c_cflag & CREAD))
+ pi->rcv_data = 0;
+ else
+ mpsc_start_rx(pi);
+
+ spin_unlock_irqrestore(&pi->port.lock, flags);
+ return;
+}
+
+static const char *
+mpsc_type(struct uart_port *port)
+{
+ pr_debug("mpsc_type[%d]: port type: %s\n", port->line,MPSC_DRIVER_NAME);
+ return MPSC_DRIVER_NAME;
+}
+
+static int
+mpsc_request_port(struct uart_port *port)
+{
+ /* Should make chip/platform specific call */
+ return 0;
+}
+
+static void
+mpsc_release_port(struct uart_port *port)
+{
+ struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+
+ if (pi->ready) {
+ mpsc_uninit_rings(pi);
+ mpsc_free_ring_mem(pi);
+ pi->ready = 0;
+ }
+
+ return;
+}
+
+static void
+mpsc_config_port(struct uart_port *port, int flags)
+{
+ return;
+}
+
+static int
+mpsc_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+ int rc = 0;
+
+ pr_debug("mpsc_verify_port[%d]: Verifying port data\n", pi->port.line);
+
+ if (ser->type != PORT_UNKNOWN && ser->type != PORT_MPSC)
+ rc = -EINVAL;
+ else if (pi->port.irq != ser->irq)
+ rc = -EINVAL;
+ else if (ser->io_type != SERIAL_IO_MEM)
+ rc = -EINVAL;
+ else if (pi->port.uartclk / 16 != ser->baud_base) /* Not sure */
+ rc = -EINVAL;
+ else if ((void *)pi->port.mapbase != ser->iomem_base)
+ rc = -EINVAL;
+ else if (pi->port.iobase != ser->port)
+ rc = -EINVAL;
+ else if (ser->hub6 != 0)
+ rc = -EINVAL;
+
+ return rc;
+}
+
+static struct uart_ops mpsc_pops = {
+ .tx_empty = mpsc_tx_empty,
+ .set_mctrl = mpsc_set_mctrl,
+ .get_mctrl = mpsc_get_mctrl,
+ .stop_tx = mpsc_stop_tx,
+ .start_tx = mpsc_start_tx,
+ .stop_rx = mpsc_stop_rx,
+ .enable_ms = mpsc_enable_ms,
+ .break_ctl = mpsc_break_ctl,
+ .startup = mpsc_startup,
+ .shutdown = mpsc_shutdown,
+ .set_termios = mpsc_set_termios,
+ .type = mpsc_type,
+ .release_port = mpsc_release_port,
+ .request_port = mpsc_request_port,
+ .config_port = mpsc_config_port,
+ .verify_port = mpsc_verify_port,
+};
+
+/*
+ ******************************************************************************
+ *
+ * Console Interface Routines
+ *
+ ******************************************************************************
+ */
+
+#ifdef CONFIG_SERIAL_MPSC_CONSOLE
+static void
+mpsc_console_write(struct console *co, const char *s, uint count)
+{
+ struct mpsc_port_info *pi = &mpsc_ports[co->index];
+ u8 *bp, *dp, add_cr = 0;
+ int i;
+
+ while (mpsc_sdma_tx_active(pi))
+ udelay(100);
+
+ while (count > 0) {
+ bp = dp = pi->txb + (pi->txr_head * MPSC_TXBE_SIZE);
+
+ for (i = 0; i < MPSC_TXBE_SIZE; i++) {
+ if (count == 0)
+ break;
+
+ if (add_cr) {
+ *(dp++) = '\r';
+ add_cr = 0;
+ }
+ else {
+ *(dp++) = *s;
+
+ if (*(s++) == '\n') { /* add '\r' after '\n' */
+ add_cr = 1;
+ count++;
+ }
+ }
+
+ count--;
+ }
+
+ dma_cache_sync((void *) bp, MPSC_TXBE_SIZE, DMA_BIDIRECTIONAL);
+#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE)
+ if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */
+ flush_dcache_range((ulong)bp,
+ (ulong)bp + MPSC_TXBE_SIZE);
+#endif
+ mpsc_setup_tx_desc(pi, i, 0);
+ pi->txr_head = (pi->txr_head + 1) & (MPSC_TXR_ENTRIES - 1);
+ mpsc_sdma_start_tx(pi);
+
+ while (mpsc_sdma_tx_active(pi))
+ udelay(100);
+
+ pi->txr_tail = (pi->txr_tail + 1) & (MPSC_TXR_ENTRIES - 1);
+ }
+
+ return;
+}
+
+static int __init
+mpsc_console_setup(struct console *co, char *options)
+{
+ struct mpsc_port_info *pi;
+ int baud, bits, parity, flow;
+
+ pr_debug("mpsc_console_setup[%d]: options: %s\n", co->index, options);
+
+ if (co->index >= MPSC_NUM_CTLRS)
+ co->index = 0;
+
+ pi = &mpsc_ports[co->index];
+
+ baud = pi->default_baud;
+ bits = pi->default_bits;
+ parity = pi->default_parity;
+ flow = pi->default_flow;
+
+ if (!pi->port.ops)
+ return -ENODEV;
+
+ spin_lock_init(&pi->port.lock); /* Temporary fix--copied from 8250.c */
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(&pi->port, co, baud, parity, bits, flow);
+}
+
+extern struct uart_driver mpsc_reg;
+static struct console mpsc_console = {
+ .name = MPSC_DEV_NAME,
+ .write = mpsc_console_write,
+ .device = uart_console_device,
+ .setup = mpsc_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &mpsc_reg,
+};
+
+static int __init
+mpsc_late_console_init(void)
+{
+ pr_debug("mpsc_late_console_init: Enter\n");
+
+ if (!(mpsc_console.flags & CON_ENABLED))
+ register_console(&mpsc_console);
+ return 0;
+}
+
+late_initcall(mpsc_late_console_init);
+
+#define MPSC_CONSOLE &mpsc_console
+#else
+#define MPSC_CONSOLE NULL
+#endif
+/*
+ ******************************************************************************
+ *
+ * Dummy Platform Driver to extract & map shared register regions
+ *
+ ******************************************************************************
+ */
+static void
+mpsc_resource_err(char *s)
+{
+ printk(KERN_WARNING "MPSC: Platform device resource error in %s\n", s);
+ return;
+}
+
+static int
+mpsc_shared_map_regs(struct platform_device *pd)
+{
+ struct resource *r;
+
+ if ((r = platform_get_resource(pd, IORESOURCE_MEM,
+ MPSC_ROUTING_BASE_ORDER)) && request_mem_region(r->start,
+ MPSC_ROUTING_REG_BLOCK_SIZE, "mpsc_routing_regs")) {
+
+ mpsc_shared_regs.mpsc_routing_base = ioremap(r->start,
+ MPSC_ROUTING_REG_BLOCK_SIZE);
+ mpsc_shared_regs.mpsc_routing_base_p = r->start;
+ }
+ else {
+ mpsc_resource_err("MPSC routing base");
+ return -ENOMEM;
+ }
+
+ if ((r = platform_get_resource(pd, IORESOURCE_MEM,
+ MPSC_SDMA_INTR_BASE_ORDER)) && request_mem_region(r->start,
+ MPSC_SDMA_INTR_REG_BLOCK_SIZE, "sdma_intr_regs")) {
+
+ mpsc_shared_regs.sdma_intr_base = ioremap(r->start,
+ MPSC_SDMA_INTR_REG_BLOCK_SIZE);
+ mpsc_shared_regs.sdma_intr_base_p = r->start;
+ }
+ else {
+ iounmap(mpsc_shared_regs.mpsc_routing_base);
+ release_mem_region(mpsc_shared_regs.mpsc_routing_base_p,
+ MPSC_ROUTING_REG_BLOCK_SIZE);
+ mpsc_resource_err("SDMA intr base");
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static void
+mpsc_shared_unmap_regs(void)
+{
+ if (!mpsc_shared_regs.mpsc_routing_base) {
+ iounmap(mpsc_shared_regs.mpsc_routing_base);
+ release_mem_region(mpsc_shared_regs.mpsc_routing_base_p,
+ MPSC_ROUTING_REG_BLOCK_SIZE);
+ }
+ if (!mpsc_shared_regs.sdma_intr_base) {
+ iounmap(mpsc_shared_regs.sdma_intr_base);
+ release_mem_region(mpsc_shared_regs.sdma_intr_base_p,
+ MPSC_SDMA_INTR_REG_BLOCK_SIZE);
+ }
+
+ mpsc_shared_regs.mpsc_routing_base = 0;
+ mpsc_shared_regs.sdma_intr_base = 0;
+
+ mpsc_shared_regs.mpsc_routing_base_p = 0;
+ mpsc_shared_regs.sdma_intr_base_p = 0;
+
+ return;
+}
+
+static int
+mpsc_shared_drv_probe(struct device *dev)
+{
+ struct platform_device *pd = to_platform_device(dev);
+ struct mpsc_shared_pdata *pdata;
+ int rc = -ENODEV;
+
+ if (pd->id == 0) {
+ if (!(rc = mpsc_shared_map_regs(pd))) {
+ pdata = (struct mpsc_shared_pdata *)dev->platform_data;
+
+ mpsc_shared_regs.MPSC_MRR_m = pdata->mrr_val;
+ mpsc_shared_regs.MPSC_RCRR_m= pdata->rcrr_val;
+ mpsc_shared_regs.MPSC_TCRR_m= pdata->tcrr_val;
+ mpsc_shared_regs.SDMA_INTR_CAUSE_m =
+ pdata->intr_cause_val;
+ mpsc_shared_regs.SDMA_INTR_MASK_m =
+ pdata->intr_mask_val;
+
+ rc = 0;
+ }
+ }
+
+ return rc;
+}
+
+static int
+mpsc_shared_drv_remove(struct device *dev)
+{
+ struct platform_device *pd = to_platform_device(dev);
+ int rc = -ENODEV;
+
+ if (pd->id == 0) {
+ mpsc_shared_unmap_regs();
+ mpsc_shared_regs.MPSC_MRR_m = 0;
+ mpsc_shared_regs.MPSC_RCRR_m = 0;
+ mpsc_shared_regs.MPSC_TCRR_m = 0;
+ mpsc_shared_regs.SDMA_INTR_CAUSE_m = 0;
+ mpsc_shared_regs.SDMA_INTR_MASK_m = 0;
+ rc = 0;
+ }
+
+ return rc;
+}
+
+static struct device_driver mpsc_shared_driver = {
+ .name = MPSC_SHARED_NAME,
+ .bus = &platform_bus_type,
+ .probe = mpsc_shared_drv_probe,
+ .remove = mpsc_shared_drv_remove,
+};
+
+/*
+ ******************************************************************************
+ *
+ * Driver Interface Routines
+ *
+ ******************************************************************************
+ */
+static struct uart_driver mpsc_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = MPSC_DRIVER_NAME,
+ .devfs_name = MPSC_DEVFS_NAME,
+ .dev_name = MPSC_DEV_NAME,
+ .major = MPSC_MAJOR,
+ .minor = MPSC_MINOR_START,
+ .nr = MPSC_NUM_CTLRS,
+ .cons = MPSC_CONSOLE,
+};
+
+static int
+mpsc_drv_map_regs(struct mpsc_port_info *pi, struct platform_device *pd)
+{
+ struct resource *r;
+
+ if ((r = platform_get_resource(pd, IORESOURCE_MEM, MPSC_BASE_ORDER)) &&
+ request_mem_region(r->start, MPSC_REG_BLOCK_SIZE, "mpsc_regs")){
+
+ pi->mpsc_base = ioremap(r->start, MPSC_REG_BLOCK_SIZE);
+ pi->mpsc_base_p = r->start;
+ }
+ else {
+ mpsc_resource_err("MPSC base");
+ return -ENOMEM;
+ }
+
+ if ((r = platform_get_resource(pd, IORESOURCE_MEM,
+ MPSC_SDMA_BASE_ORDER)) && request_mem_region(r->start,
+ MPSC_SDMA_REG_BLOCK_SIZE, "sdma_regs")) {
+
+ pi->sdma_base = ioremap(r->start,MPSC_SDMA_REG_BLOCK_SIZE);
+ pi->sdma_base_p = r->start;
+ }
+ else {
+ mpsc_resource_err("SDMA base");
+ return -ENOMEM;
+ }
+
+ if ((r = platform_get_resource(pd,IORESOURCE_MEM,MPSC_BRG_BASE_ORDER))
+ && request_mem_region(r->start, MPSC_BRG_REG_BLOCK_SIZE,
+ "brg_regs")) {
+
+ pi->brg_base = ioremap(r->start, MPSC_BRG_REG_BLOCK_SIZE);
+ pi->brg_base_p = r->start;
+ }
+ else {
+ mpsc_resource_err("BRG base");
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static void
+mpsc_drv_unmap_regs(struct mpsc_port_info *pi)
+{
+ if (!pi->mpsc_base) {
+ iounmap(pi->mpsc_base);
+ release_mem_region(pi->mpsc_base_p, MPSC_REG_BLOCK_SIZE);
+ }
+ if (!pi->sdma_base) {
+ iounmap(pi->sdma_base);
+ release_mem_region(pi->sdma_base_p, MPSC_SDMA_REG_BLOCK_SIZE);
+ }
+ if (!pi->brg_base) {
+ iounmap(pi->brg_base);
+ release_mem_region(pi->brg_base_p, MPSC_BRG_REG_BLOCK_SIZE);
+ }
+
+ pi->mpsc_base = 0;
+ pi->sdma_base = 0;
+ pi->brg_base = 0;
+
+ pi->mpsc_base_p = 0;
+ pi->sdma_base_p = 0;
+ pi->brg_base_p = 0;
+
+ return;
+}
+
+static void
+mpsc_drv_get_platform_data(struct mpsc_port_info *pi,
+ struct platform_device *pd, int num)
+{
+ struct mpsc_pdata *pdata;
+
+ pdata = (struct mpsc_pdata *)pd->dev.platform_data;
+
+ pi->port.uartclk = pdata->brg_clk_freq;
+ pi->port.iotype = UPIO_MEM;
+ pi->port.line = num;
+ pi->port.type = PORT_MPSC;
+ pi->port.fifosize = MPSC_TXBE_SIZE;
+ pi->port.membase = pi->mpsc_base;
+ pi->port.mapbase = (ulong)pi->mpsc_base;
+ pi->port.ops = &mpsc_pops;
+
+ pi->mirror_regs = pdata->mirror_regs;
+ pi->cache_mgmt = pdata->cache_mgmt;
+ pi->brg_can_tune = pdata->brg_can_tune;
+ pi->brg_clk_src = pdata->brg_clk_src;
+ pi->mpsc_max_idle = pdata->max_idle;
+ pi->default_baud = pdata->default_baud;
+ pi->default_bits = pdata->default_bits;
+ pi->default_parity = pdata->default_parity;
+ pi->default_flow = pdata->default_flow;
+
+ /* Initial values of mirrored regs */
+ pi->MPSC_CHR_1_m = pdata->chr_1_val;
+ pi->MPSC_CHR_2_m = pdata->chr_2_val;
+ pi->MPSC_CHR_10_m = pdata->chr_10_val;
+ pi->MPSC_MPCR_m = pdata->mpcr_val;
+ pi->BRG_BCR_m = pdata->bcr_val;
+
+ pi->shared_regs = &mpsc_shared_regs;
+
+ pi->port.irq = platform_get_irq(pd, 0);
+
+ return;
+}
+
+static int
+mpsc_drv_probe(struct device *dev)
+{
+ struct platform_device *pd = to_platform_device(dev);
+ struct mpsc_port_info *pi;
+ int rc = -ENODEV;
+
+ pr_debug("mpsc_drv_probe: Adding MPSC %d\n", pd->id);
+
+ if (pd->id < MPSC_NUM_CTLRS) {
+ pi = &mpsc_ports[pd->id];
+
+ if (!(rc = mpsc_drv_map_regs(pi, pd))) {
+ mpsc_drv_get_platform_data(pi, pd, pd->id);
+
+ if (!(rc = mpsc_make_ready(pi)))
+ if (!(rc = uart_add_one_port(&mpsc_reg,
+ &pi->port)))
+ rc = 0;
+ else {
+ mpsc_release_port(
+ (struct uart_port *)pi);
+ mpsc_drv_unmap_regs(pi);
+ }
+ else
+ mpsc_drv_unmap_regs(pi);
+ }
+ }
+
+ return rc;
+}
+
+static int
+mpsc_drv_remove(struct device *dev)
+{
+ struct platform_device *pd = to_platform_device(dev);
+
+ pr_debug("mpsc_drv_exit: Removing MPSC %d\n", pd->id);
+
+ if (pd->id < MPSC_NUM_CTLRS) {
+ uart_remove_one_port(&mpsc_reg, &mpsc_ports[pd->id].port);
+ mpsc_release_port((struct uart_port *)&mpsc_ports[pd->id].port);
+ mpsc_drv_unmap_regs(&mpsc_ports[pd->id]);
+ return 0;
+ }
+ else
+ return -ENODEV;
+}
+
+static struct device_driver mpsc_driver = {
+ .name = MPSC_CTLR_NAME,
+ .bus = &platform_bus_type,
+ .probe = mpsc_drv_probe,
+ .remove = mpsc_drv_remove,
+};
+
+static int __init
+mpsc_drv_init(void)
+{
+ int rc;
+
+ printk(KERN_INFO "Serial: MPSC driver $Revision: 1.00 $\n");
+
+ memset(mpsc_ports, 0, sizeof(mpsc_ports));
+ memset(&mpsc_shared_regs, 0, sizeof(mpsc_shared_regs));
+
+ if (!(rc = uart_register_driver(&mpsc_reg))) {
+ if (!(rc = driver_register(&mpsc_shared_driver))) {
+ if ((rc = driver_register(&mpsc_driver))) {
+ driver_unregister(&mpsc_shared_driver);
+ uart_unregister_driver(&mpsc_reg);
+ }
+ }
+ else
+ uart_unregister_driver(&mpsc_reg);
+ }
+
+ return rc;
+
+}
+
+static void __exit
+mpsc_drv_exit(void)
+{
+ driver_unregister(&mpsc_driver);
+ driver_unregister(&mpsc_shared_driver);
+ uart_unregister_driver(&mpsc_reg);
+ memset(mpsc_ports, 0, sizeof(mpsc_ports));
+ memset(&mpsc_shared_regs, 0, sizeof(mpsc_shared_regs));
+ return;
+}
+
+module_init(mpsc_drv_init);
+module_exit(mpsc_drv_exit);
+
+MODULE_AUTHOR("Mark A. Greer <mgreer@mvista.com>");
+MODULE_DESCRIPTION("Generic Marvell MPSC serial/UART driver $Revision: 1.00 $");
+MODULE_VERSION(MPSC_VERSION);
+MODULE_LICENSE("GPL");
+MODULE_ALIAS_CHARDEV_MAJOR(MPSC_MAJOR);
git://git.onelab.eu / linux-2.6.git / blobdiff