/*
- * Copyright (c) 2001-2002 by David Brownell
- *
+ * Copyright (C) 2001-2004 by David Brownell
+ *
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
#ifdef CONFIG_PM
-static int ehci_hub_suspend (struct usb_hcd *hcd)
+static int ehci_bus_suspend (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
int port;
+ int mask;
if (time_before (jiffies, ehci->next_statechange))
msleep(5);
spin_lock_irq (&ehci->lock);
/* stop schedules, clean any completed work */
- if (HCD_IS_RUNNING(hcd->state)) {
+ if (HC_IS_RUNNING(hcd->state)) {
ehci_quiesce (ehci);
- hcd->state = USB_STATE_QUIESCING;
+ hcd->state = HC_STATE_QUIESCING;
}
ehci->command = readl (&ehci->regs->command);
if (ehci->reclaim)
ehci->reclaim_ready = 1;
- ehci_work(ehci, NULL);
+ ehci_work(ehci);
- /* suspend any active/unsuspended ports, maybe allow wakeup */
+ /* Unlike other USB host controller types, EHCI doesn't have
+ * any notion of "global" or bus-wide suspend. The driver has
+ * to manually suspend all the active unsuspended ports, and
+ * then manually resume them in the bus_resume() routine.
+ */
+ ehci->bus_suspended = 0;
while (port--) {
u32 __iomem *reg = &ehci->regs->port_status [port];
- u32 t1 = readl (reg);
+ u32 t1 = readl (reg) & ~PORT_RWC_BITS;
u32 t2 = t1;
- if ((t1 & PORT_PE) && !(t1 & PORT_OWNER))
+ /* keep track of which ports we suspend */
+ if ((t1 & PORT_PE) && !(t1 & PORT_OWNER) &&
+ !(t1 & PORT_SUSPEND)) {
t2 |= PORT_SUSPEND;
- if (hcd->remote_wakeup)
+ set_bit(port, &ehci->bus_suspended);
+ }
+
+ /* enable remote wakeup on all ports */
+ if (device_may_wakeup(&hcd->self.root_hub->dev))
t2 |= PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E;
else
t2 &= ~(PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E);
}
/* turn off now-idle HC */
+ del_timer_sync (&ehci->watchdog);
ehci_halt (ehci);
- hcd->state = HCD_STATE_SUSPENDED;
+ hcd->state = HC_STATE_SUSPENDED;
+
+ /* allow remote wakeup */
+ mask = INTR_MASK;
+ if (!device_may_wakeup(&hcd->self.root_hub->dev))
+ mask &= ~STS_PCD;
+ writel(mask, &ehci->regs->intr_enable);
+ readl(&ehci->regs->intr_enable);
ehci->next_statechange = jiffies + msecs_to_jiffies(10);
spin_unlock_irq (&ehci->lock);
/* caller has locked the root hub, and should reset/reinit on error */
-static int ehci_hub_resume (struct usb_hcd *hcd)
+static int ehci_bus_resume (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
u32 temp;
int i;
- int intr_enable;
if (time_before (jiffies, ehci->next_statechange))
msleep(5);
spin_lock_irq (&ehci->lock);
- /* re-init operational registers in case we lost power */
- if (readl (&ehci->regs->intr_enable) == 0) {
- /* at least some APM implementations will try to deliver
- * IRQs right away, so delay them until we're ready.
- */
- intr_enable = 1;
- writel (0, &ehci->regs->segment);
- writel (ehci->periodic_dma, &ehci->regs->frame_list);
- writel ((u32)ehci->async->qh_dma, &ehci->regs->async_next);
- } else
- intr_enable = 0;
- ehci_dbg(ehci, "resume root hub%s\n",
- intr_enable ? " after power loss" : "");
+ /* Ideally and we've got a real resume here, and no port's power
+ * was lost. (For PCI, that means Vaux was maintained.) But we
+ * could instead be restoring a swsusp snapshot -- so that BIOS was
+ * the last user of the controller, not reset/pm hardware keeping
+ * state we gave to it.
+ */
+ temp = readl(&ehci->regs->intr_enable);
+ ehci_dbg(ehci, "resume root hub%s\n", temp ? "" : " after power loss");
+
+ /* at least some APM implementations will try to deliver
+ * IRQs right away, so delay them until we're ready.
+ */
+ writel(0, &ehci->regs->intr_enable);
+
+ /* re-init operational registers */
+ writel(0, &ehci->regs->segment);
+ writel(ehci->periodic_dma, &ehci->regs->frame_list);
+ writel((u32) ehci->async->qh_dma, &ehci->regs->async_next);
/* restore CMD_RUN, framelist size, and irq threshold */
writel (ehci->command, &ehci->regs->command);
- /* take ports out of suspend */
+ /* Some controller/firmware combinations need a delay during which
+ * they set up the port statuses. See Bugzilla #8190. */
+ mdelay(8);
+
+ /* manually resume the ports we suspended during bus_suspend() */
i = HCS_N_PORTS (ehci->hcs_params);
while (i--) {
temp = readl (&ehci->regs->port_status [i]);
- temp &= ~(PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E);
- if (temp & PORT_SUSPEND) {
+ temp &= ~(PORT_RWC_BITS
+ | PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E);
+ if (test_bit(i, &ehci->bus_suspended) &&
+ (temp & PORT_SUSPEND)) {
ehci->reset_done [i] = jiffies + msecs_to_jiffies (20);
temp |= PORT_RESUME;
}
mdelay (20);
while (i--) {
temp = readl (&ehci->regs->port_status [i]);
- if ((temp & PORT_SUSPEND) == 0)
- continue;
- temp &= ~PORT_RESUME;
- writel (temp, &ehci->regs->port_status [i]);
- ehci_vdbg (ehci, "resumed port %d\n", i + 1);
+ if (test_bit(i, &ehci->bus_suspended) &&
+ (temp & PORT_SUSPEND)) {
+ temp &= ~(PORT_RWC_BITS | PORT_RESUME);
+ writel (temp, &ehci->regs->port_status [i]);
+ ehci_vdbg (ehci, "resumed port %d\n", i + 1);
+ }
}
(void) readl (&ehci->regs->command);
}
ehci->next_statechange = jiffies + msecs_to_jiffies(5);
- hcd->state = USB_STATE_RUNNING;
+ hcd->state = HC_STATE_RUNNING;
/* Now we can safely re-enable irqs */
- if (intr_enable)
- writel (INTR_MASK, &ehci->regs->intr_enable);
+ writel(INTR_MASK, &ehci->regs->intr_enable);
spin_unlock_irq (&ehci->lock);
return 0;
#else
-#define ehci_hub_suspend NULL
-#define ehci_hub_resume NULL
+#define ehci_bus_suspend NULL
+#define ehci_bus_resume NULL
#endif /* CONFIG_PM */
if (!(port_status & PORT_PE)) {
/* with integrated TT, there's nobody to hand it to! */
- if (ehci_is_ARC(ehci)) {
+ if (ehci_is_TDI(ehci)) {
ehci_dbg (ehci,
"Failed to enable port %d on root hub TT\n",
index+1);
// what happens if HCS_N_CC(params) == 0 ?
port_status |= PORT_OWNER;
+ port_status &= ~PORT_RWC_BITS;
writel (port_status, &ehci->regs->port_status [index]);
} else
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
u32 temp, status = 0;
+ u32 mask;
int ports, i, retval = 1;
unsigned long flags;
/* if !USB_SUSPEND, root hub timers won't get shut down ... */
- if (!HCD_IS_RUNNING(hcd->state))
+ if (!HC_IS_RUNNING(hcd->state))
return 0;
/* init status to no-changes */
buf [1] = 0;
retval++;
}
-
+
+ /* Some boards (mostly VIA?) report bogus overcurrent indications,
+ * causing massive log spam unless we completely ignore them. It
+ * may be relevant that VIA VT8235 controlers, where PORT_POWER is
+ * always set, seem to clear PORT_OCC and PORT_CSC when writing to
+ * PORT_POWER; that's surprising, but maybe within-spec.
+ */
+ if (!ignore_oc)
+ mask = PORT_CSC | PORT_PEC | PORT_OCC;
+ else
+ mask = PORT_CSC | PORT_PEC;
+ // PORT_RESUME from hardware ~= PORT_STAT_C_SUSPEND
+
/* no hub change reports (bit 0) for now (power, ...) */
/* port N changes (bit N)? */
if (temp & PORT_OWNER) {
/* don't report this in GetPortStatus */
if (temp & PORT_CSC) {
- temp &= ~PORT_CSC;
+ temp &= ~PORT_RWC_BITS;
+ temp |= PORT_CSC;
writel (temp, &ehci->regs->port_status [i]);
}
continue;
}
if (!(temp & PORT_CONNECT))
ehci->reset_done [i] = 0;
- if ((temp & (PORT_CSC | PORT_PEC | PORT_OCC)) != 0
- // PORT_STAT_C_SUSPEND?
+ if ((temp & mask) != 0
|| ((temp & PORT_RESUME) != 0
&& time_after (jiffies,
ehci->reset_done [i]))) {
temp = 0x0008; /* per-port overcurrent reporting */
if (HCS_PPC (ehci->hcs_params))
temp |= 0x0001; /* per-port power control */
+ else
+ temp |= 0x0002; /* no power switching */
#if 0
// re-enable when we support USB_PORT_FEAT_INDICATOR below.
if (HCS_INDICATOR (ehci->hcs_params))
/*-------------------------------------------------------------------------*/
-#define PORT_WAKE_BITS (PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E)
+#define PORT_WAKE_BITS (PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E)
static int ehci_hub_control (
struct usb_hcd *hcd,
u32 temp, status;
unsigned long flags;
int retval = 0;
+ unsigned selector;
/*
* FIXME: support SetPortFeatures USB_PORT_FEAT_INDICATOR.
&ehci->regs->port_status [wIndex]);
break;
case USB_PORT_FEAT_C_ENABLE:
- writel (temp | PORT_PEC,
+ writel((temp & ~PORT_RWC_BITS) | PORT_PEC,
&ehci->regs->port_status [wIndex]);
break;
case USB_PORT_FEAT_SUSPEND:
if (temp & PORT_RESET)
goto error;
+ if (ehci->no_selective_suspend)
+ break;
if (temp & PORT_SUSPEND) {
if ((temp & PORT_PE) == 0)
goto error;
/* resume signaling for 20 msec */
- writel ((temp & ~PORT_WAKE_BITS) | PORT_RESUME,
+ temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
+ writel (temp | PORT_RESUME,
&ehci->regs->port_status [wIndex]);
ehci->reset_done [wIndex] = jiffies
+ msecs_to_jiffies (20);
break;
case USB_PORT_FEAT_POWER:
if (HCS_PPC (ehci->hcs_params))
- writel (temp & ~PORT_POWER,
+ writel (temp & ~(PORT_RWC_BITS | PORT_POWER),
&ehci->regs->port_status [wIndex]);
break;
case USB_PORT_FEAT_C_CONNECTION:
- writel (temp | PORT_CSC,
+ writel((temp & ~PORT_RWC_BITS) | PORT_CSC,
&ehci->regs->port_status [wIndex]);
break;
case USB_PORT_FEAT_C_OVER_CURRENT:
- writel (temp | PORT_OCC,
+ writel((temp & ~PORT_RWC_BITS) | PORT_OCC,
&ehci->regs->port_status [wIndex]);
break;
case USB_PORT_FEAT_C_RESET:
status |= 1 << USB_PORT_FEAT_C_CONNECTION;
if (temp & PORT_PEC)
status |= 1 << USB_PORT_FEAT_C_ENABLE;
- if (temp & PORT_OCC)
+ if ((temp & PORT_OCC) && !ignore_oc)
status |= 1 << USB_PORT_FEAT_C_OVER_CURRENT;
/* whoever resumes must GetPortStatus to complete it!! */
/* stop resume signaling */
temp = readl (&ehci->regs->port_status [wIndex]);
- writel (temp & ~PORT_RESUME,
+ writel (temp & ~(PORT_RWC_BITS | PORT_RESUME),
&ehci->regs->port_status [wIndex]);
retval = handshake (
&ehci->regs->port_status [wIndex],
ehci->reset_done [wIndex] = 0;
/* force reset to complete */
- writel (temp & ~PORT_RESET,
+ writel (temp & ~(PORT_RWC_BITS | PORT_RESET),
&ehci->regs->port_status [wIndex]);
+ /* REVISIT: some hardware needs 550+ usec to clear
+ * this bit; seems too long to spin routinely...
+ */
retval = handshake (
&ehci->regs->port_status [wIndex],
- PORT_RESET, 0, 500);
+ PORT_RESET, 0, 750);
if (retval != 0) {
ehci_err (ehci, "port %d reset error %d\n",
wIndex + 1, retval);
}
break;
case SetPortFeature:
+ selector = wIndex >> 8;
+ wIndex &= 0xff;
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
if (temp & PORT_OWNER)
break;
+ temp &= ~PORT_RWC_BITS;
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
+ if (ehci->no_selective_suspend)
+ break;
if ((temp & PORT_PE) == 0
|| (temp & PORT_RESET) != 0)
goto error;
- if (hcd->remote_wakeup)
+ if (device_may_wakeup(&hcd->self.root_hub->dev))
temp |= PORT_WAKE_BITS;
writel (temp | PORT_SUSPEND,
&ehci->regs->port_status [wIndex]);
* transaction translator built in.
*/
if ((temp & (PORT_PE|PORT_CONNECT)) == PORT_CONNECT
- && !ehci_is_ARC(ehci)
+ && !ehci_is_TDI(ehci)
&& PORT_USB11 (temp)) {
ehci_dbg (ehci,
"port %d low speed --> companion\n",
}
writel (temp, &ehci->regs->port_status [wIndex]);
break;
+
+ /* For downstream facing ports (these): one hub port is put
+ * into test mode according to USB2 11.24.2.13, then the hub
+ * must be reset (which for root hub now means rmmod+modprobe,
+ * or else system reboot). See EHCI 2.3.9 and 4.14 for info
+ * about the EHCI-specific stuff.
+ */
+ case USB_PORT_FEAT_TEST:
+ if (!selector || selector > 5)
+ goto error;
+ ehci_quiesce(ehci);
+ ehci_halt(ehci);
+ temp |= selector << 16;
+ writel (temp, &ehci->regs->port_status [wIndex]);
+ break;
+
default:
goto error;
}