* OHCI HCD (Host Controller Driver) for USB.
*
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
- * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
+ * (C) Copyright 2000-2005 David Brownell
* (C) Copyright 2002 Hewlett-Packard Company
- *
- * OMAP Bus Glue
*
- * Written by Christopher Hoover <ch@hpl.hp.com>
- * Based on fragments of previous driver by Rusell King et al.
+ * OMAP Bus Glue
*
- * Modified for OMAP from ohci-sa1111.c by Tony Lindgren <tony@atomide.com>
+ * Modified for OMAP by Tony Lindgren <tony@atomide.com>
* Based on the 2.4 OMAP OHCI driver originally done by MontaVista Software Inc.
+ * and on ohci-sa1111.c by Christopher Hoover <ch@hpl.hp.com>
*
* This file is licenced under the GPL.
*/
-
+
+#include <linux/signal.h> /* IRQF_DISABLED */
+#include <linux/jiffies.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+
#include <asm/hardware.h>
#include <asm/io.h>
+#include <asm/mach-types.h>
-#include <asm/arch/bus.h>
-#include <asm/arch/hardware.h>
#include <asm/arch/mux.h>
#include <asm/arch/irqs.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/fpga.h>
+#include <asm/arch/usb.h>
+
+
+/* OMAP-1510 OHCI has its own MMU for DMA */
+#define OMAP1510_LB_MEMSIZE 32 /* Should be same as SDRAM size */
+#define OMAP1510_LB_CLOCK_DIV 0xfffec10c
+#define OMAP1510_LB_MMU_CTL 0xfffec208
+#define OMAP1510_LB_MMU_LCK 0xfffec224
+#define OMAP1510_LB_MMU_LD_TLB 0xfffec228
+#define OMAP1510_LB_MMU_CAM_H 0xfffec22c
+#define OMAP1510_LB_MMU_CAM_L 0xfffec230
+#define OMAP1510_LB_MMU_RAM_H 0xfffec234
+#define OMAP1510_LB_MMU_RAM_L 0xfffec238
-#include "ohci-omap.h"
#ifndef CONFIG_ARCH_OMAP
#error "This file is OMAP bus glue. CONFIG_OMAP must be defined."
#endif
-extern int usb_disabled(void);
-extern int ocpi_enable(void);
+#ifdef CONFIG_TPS65010
+#include <asm/arch/tps65010.h>
+#else
-/*
- * Use the first port only by default. Override with hmc_mode option.
- *
- * NOTE: Many OMAP-1510 Innovators supposedly have bad wiring for the USB ports
- * 1 & 2, so only port 0 will work. To use the OHCI on the first port, use
- * the Innovator USB client cable with a client-to-client connector and modify
- * either the cable or the hub to feed 5V VBUS back to Innovator. VBUS should
- * be the red lead in the cable.
- *
- * To mount USB hard disk as root, see the patch for do_mounts.c that tries
- * remounting the root, and use root=0801 if your root is on sda1. Does not
- * work with devfs.
- */
-static int default_hmc_mode = 16;
-static int hmc_mode = 1234;
-
-/*
- * Set the USB host pin multiplexing and the selected HMC mode
- */
-static int omap_usb_set_hmc_mode(int hmc_mode)
-{
- unsigned int val;
-
- switch (hmc_mode) {
- case 0:
- /* 0: function, 1: disabled, 2: disabled */
- omap_cfg_reg(W4_USB_PUEN);
- omap_cfg_reg(R18_1510_USB_GPIO0);
- break;
- case 4:
- /* 0: function 1: host 2: host */
- omap_cfg_reg(usb1_speed);
- omap_cfg_reg(usb1_susp);
- omap_cfg_reg(usb1_seo);
- omap_cfg_reg(usb1_txen);
- omap_cfg_reg(usb1_txd);
- omap_cfg_reg(usb1_vp);
- omap_cfg_reg(usb1_vm);
- omap_cfg_reg(usb1_rcv);
- omap_cfg_reg(usb2_susp);
- omap_cfg_reg(usb2_seo);
- omap_cfg_reg(usb2_txen);
- omap_cfg_reg(usb2_txd);
- omap_cfg_reg(usb2_vp);
- omap_cfg_reg(usb2_vm);
- omap_cfg_reg(usb2_rcv);
- break;
- case 16:
- /* 0: host, 1: disabled, 2: disabled */
- omap_cfg_reg(W9_USB0_TXEN);
- omap_cfg_reg(AA9_USB0_VP);
- omap_cfg_reg(Y5_USB0_RCV);
- omap_cfg_reg(R9_USB0_VM);
- omap_cfg_reg(V6_USB0_TXD);
- omap_cfg_reg(W5_USB0_SE0);
- break;
- default:
- printk("Unknown USB host configuration: %i\n", hmc_mode);
- return -ENODEV;
- }
+#define LOW 0
+#define HIGH 1
- /* Write the selected HMC mode */
- val = readl(MOD_CONF_CTRL_0) & ~HMC_CLEAR;
- val |= (hmc_mode << 1);
- writel(val, MOD_CONF_CTRL_0);
+#define GPIO1 1
+static inline int tps65010_set_gpio_out_value(unsigned gpio, unsigned value)
+{
return 0;
}
-/*
- * OHCI clock initialization for OMAP-1510 and 1610
- */
-static int omap_ohci_clock_power(int on)
-{
- if (on) {
- if (cpu_is_omap_1510()) {
- /* Use DPLL, not APLL */
- writel(readl(ULPD_APLL_CTRL_REG) & ~APLL_NDPLL_SWITCH,
- ULPD_APLL_CTRL_REG);
-
- /* Enable DPLL */
- writel(readl(ULPD_DPLL_CTRL_REG) | DPLL_PLL_ENABLE,
- ULPD_DPLL_CTRL_REG);
-
- /* Software request for USB 48MHz clock */
- writel(readl(ULPD_SOFT_REQ_REG) | SOFT_REQ_REG_REQ,
- ULPD_SOFT_REQ_REG);
-
- while (!(readl(ULPD_DPLL_CTRL_REG) & DPLL_LOCK));
- }
-
- if (cpu_is_omap_1610()) {
- /* Enable OHCI */
- writel(readl(ULPD_SOFT_REQ_REG) | SOFT_USB_OTG_REQ,
- ULPD_SOFT_REQ_REG);
-
- /* USB host clock request if not using OTG */
- writel(readl(ULPD_SOFT_REQ_REG) | SOFT_USB_REQ,
- ULPD_SOFT_REQ_REG);
-
- writel(readl(ULPD_STATUS_REQ_REG) | USB_HOST_DPLL_REQ,
- ULPD_STATUS_REQ_REG);
- }
+#endif
- /* Enable 48MHz clock to USB */
- writel(readl(ULPD_CLOCK_CTRL_REG) | USB_MCLK_EN,
- ULPD_CLOCK_CTRL_REG);
+extern int usb_disabled(void);
+extern int ocpi_enable(void);
- writel(readl(ARM_IDLECT2) | (1 << EN_LBFREECK) | (1 << EN_LBCK),
- ARM_IDLECT2);
+static struct clk *usb_host_ck;
+static struct clk *usb_dc_ck;
+static int host_enabled;
+static int host_initialized;
- writel(readl(MOD_CONF_CTRL_0) | USB_HOST_HHC_UHOST_EN,
- MOD_CONF_CTRL_0);
+static void omap_ohci_clock_power(int on)
+{
+ if (on) {
+ clk_enable(usb_dc_ck);
+ clk_enable(usb_host_ck);
+ /* guesstimate for T5 == 1x 32K clock + APLL lock time */
+ udelay(100);
} else {
- /* Disable 48MHz clock to USB */
- writel(readl(ULPD_CLOCK_CTRL_REG) & ~USB_MCLK_EN,
- ULPD_CLOCK_CTRL_REG);
-
- /* FIXME: The DPLL stays on for now */
+ clk_disable(usb_host_ck);
+ clk_disable(usb_dc_ck);
}
-
- return 0;
}
/*
- * Hardware specific transceiver power on/off
+ * Board specific gang-switched transceiver power on/off.
+ * NOTE: OSK supplies power from DC, not battery.
*/
static int omap_ohci_transceiver_power(int on)
{
if (on) {
- if (omap_is_innovator())
- writel(readl(OMAP1510_FPGA_HOST_CTRL) | 0x20,
- OMAP1510_FPGA_HOST_CTRL);
+ if (machine_is_omap_innovator() && cpu_is_omap1510())
+ fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
+ | ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
+ INNOVATOR_FPGA_CAM_USB_CONTROL);
+ else if (machine_is_omap_osk())
+ tps65010_set_gpio_out_value(GPIO1, LOW);
} else {
- if (omap_is_innovator())
- writel(readl(OMAP1510_FPGA_HOST_CTRL) & ~0x20,
- OMAP1510_FPGA_HOST_CTRL);
+ if (machine_is_omap_innovator() && cpu_is_omap1510())
+ fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
+ & ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
+ INNOVATOR_FPGA_CAM_USB_CONTROL);
+ else if (machine_is_omap_osk())
+ tps65010_set_gpio_out_value(GPIO1, HIGH);
}
return 0;
}
+#ifdef CONFIG_ARCH_OMAP15XX
/*
* OMAP-1510 specific Local Bus clock on/off
*/
static int omap_1510_local_bus_power(int on)
{
if (on) {
- writel((1 << 1) | (1 << 0), OMAP1510_LB_MMU_CTL);
+ omap_writel((1 << 1) | (1 << 0), OMAP1510_LB_MMU_CTL);
udelay(200);
} else {
- writel(0, OMAP1510_LB_MMU_CTL);
+ omap_writel(0, OMAP1510_LB_MMU_CTL);
}
return 0;
/*
* OMAP-1510 specific Local Bus initialization
* NOTE: This assumes 32MB memory size in OMAP1510LB_MEMSIZE.
- * See also arch/mach-omap/memory.h for __virt_to_bus() and
- * __bus_to_virt() which need to match with the physical
+ * See also arch/mach-omap/memory.h for __virt_to_dma() and
+ * __dma_to_virt() which need to match with the physical
* Local Bus address below.
*/
static int omap_1510_local_bus_init(void)
unsigned int tlb;
unsigned long lbaddr, physaddr;
- writel((readl(OMAP1510_LB_CLOCK_DIV) & 0xfffffff8) | 0x4,
+ omap_writel((omap_readl(OMAP1510_LB_CLOCK_DIV) & 0xfffffff8) | 0x4,
OMAP1510_LB_CLOCK_DIV);
/* Configure the Local Bus MMU table */
for (tlb = 0; tlb < OMAP1510_LB_MEMSIZE; tlb++) {
lbaddr = tlb * 0x00100000 + OMAP1510_LB_OFFSET;
physaddr = tlb * 0x00100000 + PHYS_OFFSET;
- writel((lbaddr & 0x0fffffff) >> 22, OMAP1510_LB_MMU_CAM_H);
- writel(((lbaddr & 0x003ffc00) >> 6) | 0xc,
+ omap_writel((lbaddr & 0x0fffffff) >> 22, OMAP1510_LB_MMU_CAM_H);
+ omap_writel(((lbaddr & 0x003ffc00) >> 6) | 0xc,
OMAP1510_LB_MMU_CAM_L);
- writel(physaddr >> 16, OMAP1510_LB_MMU_RAM_H);
- writel((physaddr & 0x0000fc00) | 0x300, OMAP1510_LB_MMU_RAM_L);
- writel(tlb << 4, OMAP1510_LB_MMU_LCK);
- writel(0x1, OMAP1510_LB_MMU_LD_TLB);
+ omap_writel(physaddr >> 16, OMAP1510_LB_MMU_RAM_H);
+ omap_writel((physaddr & 0x0000fc00) | 0x300, OMAP1510_LB_MMU_RAM_L);
+ omap_writel(tlb << 4, OMAP1510_LB_MMU_LCK);
+ omap_writel(0x1, OMAP1510_LB_MMU_LD_TLB);
}
/* Enable the walking table */
- writel(readl(OMAP1510_LB_MMU_CTL) | (1 << 3), OMAP1510_LB_MMU_CTL);
+ omap_writel(omap_readl(OMAP1510_LB_MMU_CTL) | (1 << 3), OMAP1510_LB_MMU_CTL);
udelay(200);
return 0;
}
+#else
+#define omap_1510_local_bus_power(x) {}
+#define omap_1510_local_bus_init() {}
+#endif
-/*
- * OMAP-1610 specific hardware initialization
- *
- * Intended to configure OMAP-1610 USB host and OTG ports depending on
- * the HMC mode selected.
- *
- * FIXME: Currently only supports alternate ping group 2 mode, should
- * be easy to modify for other configurations once there is some
- * hardware to test with.
- */
-static int omap_1610_usb_init(int mode)
-{
- u_int val = 0;
-
- /* Configure the OMAP transceiver settings */
- val |= (1 << 8); /* CONF_USB2_UNI TRM p 15-205*/
- val |= (4 << 4); /* TRM p 5-59, p 15-157 (1224) */
-
- //val |= (1 << 3); /* Isolate integrated transceiver from port 0 */
- val |= (1 << 2); /* Disable pulldown on integrated transceiver DM */
- val |= (1 << 1); /* Disable pulldown on integraded transceiver DP */
-
- writel(val, USB_TRANSCEIVER_CTRL);
-
- /* Set the USB0_TRX_MODE */
- val = 0;
- val &= ~OTG_IDLE_EN;
- val &= ~DEV_IDLE_EN;
- val &= ~(7 << 16); /* Clear USB0_TRX_MODE */
- val |= (3 << 16); /* 0 or 3, 6-wire DAT/SE0, TRM p 15-159 */
- writel(val, OTG_SYSCON_1);
-
- /*
- * Control via OTG, see TRM p 15-163
- */
- val = 0;
- //val |= 1; /* REVISIT: Enable OTG = 1 */
-
- /* Control via OTG */
- val &= ~HMC_PADEN;
- val &= ~OTG_PADEN;
- val |= UHOST_EN;
+#ifdef CONFIG_USB_OTG
- val &= ~0x3f; /* Clear HMC mode */
- val |= mode; /* Set HMC mode */
- val &= ~(7 << 16); /* Clear ASE0_BRST */
- val |= (4 << 16); /* Must be 4 */
- val |= USBX_SYNCHRO; /* Must be set */
- val |= SRP_VBUS;
- writel(val, OTG_SYSCON_2);
+static void start_hnp(struct ohci_hcd *ohci)
+{
+ const unsigned port = ohci_to_hcd(ohci)->self.otg_port - 1;
+ unsigned long flags;
- /* Enable OTG idle */
- //writel(readl(OTG_SYSCON_1) | OTG_IDLE_EN, OTG_SYSCON_1);
+ otg_start_hnp(ohci->transceiver);
- return 0;
+ local_irq_save(flags);
+ ohci->transceiver->state = OTG_STATE_A_SUSPEND;
+ writel (RH_PS_PSS, &ohci->regs->roothub.portstatus [port]);
+ OTG_CTRL_REG &= ~OTG_A_BUSREQ;
+ local_irq_restore(flags);
}
+#endif
+
/*-------------------------------------------------------------------------*/
-static void omap_start_hc(struct omap_dev *dev)
+static int ohci_omap_init(struct usb_hcd *hcd)
{
- printk(KERN_DEBUG __FILE__
- ": starting OMAP OHCI USB Controller\n");
+ struct ohci_hcd *ohci = hcd_to_ohci(hcd);
+ struct omap_usb_config *config = hcd->self.controller->platform_data;
+ int need_transceiver = (config->otg != 0);
+ int ret;
- /*
- * Set the HMC mode for the USB ports
- */
-#if 0
- /* See note about the Innovator wiring above */
- if (omap_is_innovator())
- hmc_mode = 4; /* 0: function 1: host 2: host */
-#endif
+ dev_dbg(hcd->self.controller, "starting USB Controller\n");
- if (cpu_is_omap_1610())
+ if (config->otg) {
+ ohci_to_hcd(ohci)->self.otg_port = config->otg;
+ /* default/minimum OTG power budget: 8 mA */
+ ohci_to_hcd(ohci)->power_budget = 8;
+ }
+
+ /* boards can use OTG transceivers in non-OTG modes */
+ need_transceiver = need_transceiver
+ || machine_is_omap_h2() || machine_is_omap_h3();
+
+ if (cpu_is_omap16xx())
ocpi_enable();
- omap_usb_set_hmc_mode(hmc_mode);
+#ifdef CONFIG_ARCH_OMAP_OTG
+ if (need_transceiver) {
+ ohci->transceiver = otg_get_transceiver();
+ if (ohci->transceiver) {
+ int status = otg_set_host(ohci->transceiver,
+ &ohci_to_hcd(ohci)->self);
+ dev_dbg(hcd->self.controller, "init %s transceiver, status %d\n",
+ ohci->transceiver->label, status);
+ if (status) {
+ if (ohci->transceiver)
+ put_device(ohci->transceiver->dev);
+ return status;
+ }
+ } else {
+ dev_err(hcd->self.controller, "can't find transceiver\n");
+ return -ENODEV;
+ }
+ }
+#endif
omap_ohci_clock_power(1);
- omap_ohci_transceiver_power(1);
- if (cpu_is_omap_1510()) {
+ if (cpu_is_omap1510()) {
omap_1510_local_bus_power(1);
omap_1510_local_bus_init();
}
- if (cpu_is_omap_1610())
- omap_1610_usb_init(hmc_mode);
+ if ((ret = ohci_init(ohci)) < 0)
+ return ret;
- //omap_enable_device(dev);
-}
+ /* board-specific power switching and overcurrent support */
+ if (machine_is_omap_osk() || machine_is_omap_innovator()) {
+ u32 rh = roothub_a (ohci);
-static void omap_stop_hc(struct omap_dev *dev)
-{
- printk(KERN_DEBUG __FILE__
- ": stopping OMAP OHCI USB Controller\n");
+ /* power switching (ganged by default) */
+ rh &= ~RH_A_NPS;
- /*
- * FIXME: Put the USB host controller into reset.
- */
+ /* TPS2045 switch for internal transceiver (port 1) */
+ if (machine_is_omap_osk()) {
+ ohci_to_hcd(ohci)->power_budget = 250;
- /*
- * FIXME: Stop the USB clock.
- */
- //omap_disable_device(dev);
+ rh &= ~RH_A_NOCP;
-}
+ /* gpio9 for overcurrent detction */
+ omap_cfg_reg(W8_1610_GPIO9);
+ omap_request_gpio(9);
+ omap_set_gpio_direction(9, 1 /* IN */);
+ /* for paranoia's sake: disable USB.PUEN */
+ omap_cfg_reg(W4_USB_HIGHZ);
+ }
+ ohci_writel(ohci, rh, &ohci->regs->roothub.a);
+ distrust_firmware = 0;
+ } else if (machine_is_nokia770()) {
+ /* We require a self-powered hub, which should have
+ * plenty of power. */
+ ohci_to_hcd(ohci)->power_budget = 0;
+ }
-/*-------------------------------------------------------------------------*/
+ /* FIXME khubd hub requests should manage power switching */
+ omap_ohci_transceiver_power(1);
-static irqreturn_t usb_hcd_omap_hcim_irq (int irq, void *__hcd, struct pt_regs * r)
-{
- struct usb_hcd *hcd = __hcd;
+ /* board init will have already handled HMC and mux setup.
+ * any external transceiver should already be initialized
+ * too, so all configured ports use the right signaling now.
+ */
- return usb_hcd_irq(irq, hcd, r);
+ return 0;
}
-/*-------------------------------------------------------------------------*/
-
-void usb_hcd_omap_remove (struct usb_hcd *, struct omap_dev *);
+static void ohci_omap_stop(struct usb_hcd *hcd)
+{
+ dev_dbg(hcd->self.controller, "stopping USB Controller\n");
+ omap_ohci_clock_power(0);
+}
-/* configure so an HC device and id are always provided */
-/* always called with process context; sleeping is OK */
+/*-------------------------------------------------------------------------*/
/**
* usb_hcd_omap_probe - initialize OMAP-based HCDs
* Allocates basic resources for this USB host controller, and
* then invokes the start() method for the HCD associated with it
* through the hotplug entry's driver_data.
- *
- * Store this function in the HCD's struct pci_driver as probe().
*/
-int usb_hcd_omap_probe (const struct hc_driver *driver,
- struct usb_hcd **hcd_out,
- struct omap_dev *dev)
+static int usb_hcd_omap_probe (const struct hc_driver *driver,
+ struct platform_device *pdev)
{
- int retval;
+ int retval, irq;
struct usb_hcd *hcd = 0;
+ struct ohci_hcd *ohci;
- if (!request_mem_region(dev->res.start,
- dev->res.end - dev->res.start + 1, hcd_name)) {
- dbg("request_mem_region failed");
- return -EBUSY;
+ if (pdev->num_resources != 2) {
+ printk(KERN_ERR "hcd probe: invalid num_resources: %i\n",
+ pdev->num_resources);
+ return -ENODEV;
}
- omap_start_hc(dev);
+ if (pdev->resource[0].flags != IORESOURCE_MEM
+ || pdev->resource[1].flags != IORESOURCE_IRQ) {
+ printk(KERN_ERR "hcd probe: invalid resource type\n");
+ return -ENODEV;
+ }
- hcd = driver->hcd_alloc ();
- if (hcd == NULL){
- dbg ("hcd_alloc failed");
- retval = -ENOMEM;
- goto err1;
+ usb_host_ck = clk_get(0, "usb_hhc_ck");
+ if (IS_ERR(usb_host_ck))
+ return PTR_ERR(usb_host_ck);
+
+ if (!cpu_is_omap1510())
+ usb_dc_ck = clk_get(0, "usb_dc_ck");
+ else
+ usb_dc_ck = clk_get(0, "lb_ck");
+
+ if (IS_ERR(usb_dc_ck)) {
+ clk_put(usb_host_ck);
+ return PTR_ERR(usb_dc_ck);
}
- hcd->driver = (struct hc_driver *) driver;
- hcd->description = driver->description;
- hcd->irq = dev->irq[0];
- hcd->regs = dev->mapbase;
- hcd->self.controller = &dev->dev;
- retval = hcd_buffer_create (hcd);
- if (retval != 0) {
- dbg ("pool alloc fail");
- goto err1;
+ hcd = usb_create_hcd (driver, &pdev->dev, pdev->dev.bus_id);
+ if (!hcd) {
+ retval = -ENOMEM;
+ goto err0;
}
+ hcd->rsrc_start = pdev->resource[0].start;
+ hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
- retval = request_irq (hcd->irq,
- usb_hcd_omap_hcim_irq,
- SA_INTERRUPT, hcd->description, hcd);
- if (retval != 0) {
- dbg("request_irq failed");
+ if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
+ dev_dbg(&pdev->dev, "request_mem_region failed\n");
retval = -EBUSY;
- goto err2;
+ goto err1;
}
- info ("%s (OMAP) at 0x%p, irq %d\n",
- hcd->description, hcd->regs, hcd->irq);
+ hcd->regs = (void __iomem *) (int) IO_ADDRESS(hcd->rsrc_start);
- usb_bus_init (&hcd->self);
- hcd->self.op = &usb_hcd_operations;
- hcd->self.hcpriv = (void *) hcd;
- hcd->self.bus_name = "omap";
- hcd->product_desc = "OMAP OHCI";
+ ohci = hcd_to_ohci(hcd);
+ ohci_hcd_init(ohci);
- INIT_LIST_HEAD (&hcd->dev_list);
- usb_register_bus (&hcd->self);
+ host_initialized = 0;
+ host_enabled = 1;
- if ((retval = driver->start (hcd)) < 0)
- {
- usb_hcd_omap_remove(hcd, dev);
- return retval;
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ retval = -ENXIO;
+ goto err2;
}
+ retval = usb_add_hcd(hcd, irq, IRQF_DISABLED);
+ if (retval)
+ goto err2;
- *hcd_out = hcd;
- return 0;
-
- err2:
- hcd_buffer_destroy (hcd);
- if (hcd)
- driver->hcd_free(hcd);
- err1:
- omap_stop_hc(dev);
+ host_initialized = 1;
- release_mem_region(dev->res.start, dev->res.end - dev->res.start + 1);
+ if (!host_enabled)
+ omap_ohci_clock_power(0);
+ return 0;
+err2:
+ release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+err1:
+ usb_put_hcd(hcd);
+err0:
+ clk_put(usb_dc_ck);
+ clk_put(usb_host_ck);
return retval;
}
-/* may be called without controller electrically present */
/* may be called with controller, bus, and devices active */
/**
* Reverses the effect of usb_hcd_omap_probe(), first invoking
* the HCD's stop() method. It is always called from a thread
* context, normally "rmmod", "apmd", or something similar.
- *
*/
-void usb_hcd_omap_remove (struct usb_hcd *hcd, struct omap_dev *dev)
+static inline void
+usb_hcd_omap_remove (struct usb_hcd *hcd, struct platform_device *pdev)
{
- void *base;
-
- info ("remove: %s, state %x", hcd->self.bus_name, hcd->state);
-
- if (in_interrupt ())
- BUG ();
+ struct ohci_hcd *ohci = hcd_to_ohci (hcd);
- hcd->state = USB_STATE_QUIESCING;
-
- dbg ("%s: roothub graceful disconnect", hcd->self.bus_name);
- usb_disconnect (&hcd->self.root_hub);
-
- hcd->driver->stop (hcd);
- hcd_buffer_destroy (hcd);
- hcd->state = USB_STATE_HALT;
-
- free_irq (hcd->irq, hcd);
-
- usb_deregister_bus (&hcd->self);
-
- base = hcd->regs;
- hcd->driver->hcd_free (hcd);
-
- omap_stop_hc(dev);
-
- release_mem_region(dev->res.start, dev->res.end - dev->res.start + 1);
+ usb_remove_hcd(hcd);
+ if (ohci->transceiver) {
+ (void) otg_set_host(ohci->transceiver, 0);
+ put_device(ohci->transceiver->dev);
+ }
+ if (machine_is_omap_osk())
+ omap_free_gpio(9);
+ release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+ usb_put_hcd(hcd);
+ clk_put(usb_dc_ck);
+ clk_put(usb_host_ck);
}
/*-------------------------------------------------------------------------*/
-static int __devinit
+static int
ohci_omap_start (struct usb_hcd *hcd)
{
+ struct omap_usb_config *config;
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
int ret;
- ohci->hcca = dma_alloc_consistent (hcd->self.controller,
- sizeof *ohci->hcca, &ohci->hcca_dma);
- if (!ohci->hcca)
- return -ENOMEM;
-
- memset (ohci->hcca, 0, sizeof (struct ohci_hcca));
- if ((ret = ohci_mem_init (ohci)) < 0) {
- ohci_stop (hcd);
- return ret;
- }
- ohci->regs = hcd->regs;
- if (hc_reset (ohci) < 0) {
- ohci_stop (hcd);
- return -ENODEV;
+ if (!host_enabled)
+ return 0;
+ config = hcd->self.controller->platform_data;
+ if (config->otg || config->rwc) {
+ ohci->hc_control = OHCI_CTRL_RWC;
+ writel(OHCI_CTRL_RWC, &ohci->regs->control);
}
- if (hc_start (ohci) < 0) {
- err ("can't start %s", ohci->hcd.self.bus_name);
+ if ((ret = ohci_run (ohci)) < 0) {
+ dev_err(hcd->self.controller, "can't start\n");
ohci_stop (hcd);
- return -EBUSY;
+ return ret;
}
- create_debug_files (ohci);
-
-#ifdef DEBUG
- ohci_dump (ohci, 1);
-#endif
return 0;
}
static const struct hc_driver ohci_omap_hc_driver = {
.description = hcd_name,
+ .product_desc = "OMAP OHCI",
+ .hcd_priv_size = sizeof(struct ohci_hcd),
/*
* generic hardware linkage
*/
.irq = ohci_irq,
- .flags = HCD_USB11,
+ .flags = HCD_USB11 | HCD_MEMORY,
/*
* basic lifecycle operations
*/
+ .reset = ohci_omap_init,
.start = ohci_omap_start,
-#ifdef CONFIG_PM
- /* suspend: ohci_omap_suspend, -- tbd */
- /* resume: ohci_omap_resume, -- tbd */
-#endif
- .stop = ohci_stop,
-
- /*
- * memory lifecycle (except per-request)
- */
- .hcd_alloc = ohci_hcd_alloc,
- .hcd_free = ohci_hcd_free,
+ .stop = ohci_omap_stop,
+ .shutdown = ohci_shutdown,
/*
* managing i/o requests and associated device resources
*/
.hub_status_data = ohci_hub_status_data,
.hub_control = ohci_hub_control,
-#ifdef CONFIG_USB_SUSPEND
- .hub_suspend = ohci_hub_suspend,
- .hub_resume = ohci_hub_resume,
+ .hub_irq_enable = ohci_rhsc_enable,
+#ifdef CONFIG_PM
+ .bus_suspend = ohci_bus_suspend,
+ .bus_resume = ohci_bus_resume,
#endif
+ .start_port_reset = ohci_start_port_reset,
};
/*-------------------------------------------------------------------------*/
-static int ohci_hcd_omap_drv_probe(struct omap_dev *dev)
+static int ohci_hcd_omap_drv_probe(struct platform_device *dev)
{
- struct usb_hcd *hcd = NULL;
- int ret;
-
- if (usb_disabled())
- return -ENODEV;
+ return usb_hcd_omap_probe(&ohci_omap_hc_driver, dev);
+}
- ret = usb_hcd_omap_probe(&ohci_omap_hc_driver, &hcd, dev);
+static int ohci_hcd_omap_drv_remove(struct platform_device *dev)
+{
+ struct usb_hcd *hcd = platform_get_drvdata(dev);
- if (ret == 0)
- omap_set_drvdata(dev, hcd);
+ usb_hcd_omap_remove(hcd, dev);
+ platform_set_drvdata(dev, NULL);
- return ret;
+ return 0;
}
-static int ohci_hcd_omap_drv_remove(struct omap_dev *dev)
+/*-------------------------------------------------------------------------*/
+
+#ifdef CONFIG_PM
+
+static int ohci_omap_suspend(struct platform_device *dev, pm_message_t message)
{
- struct usb_hcd *hcd = omap_get_drvdata(dev);
+ struct ohci_hcd *ohci = hcd_to_ohci(platform_get_drvdata(dev));
- usb_hcd_omap_remove(hcd, dev);
+ if (time_before(jiffies, ohci->next_statechange))
+ msleep(5);
+ ohci->next_statechange = jiffies;
+
+ omap_ohci_clock_power(0);
+ ohci_to_hcd(ohci)->state = HC_STATE_SUSPENDED;
+ dev->dev.power.power_state = PMSG_SUSPEND;
+ return 0;
+}
+
+static int ohci_omap_resume(struct platform_device *dev)
+{
+ struct ohci_hcd *ohci = hcd_to_ohci(platform_get_drvdata(dev));
- omap_set_drvdata(dev, NULL);
+ if (time_before(jiffies, ohci->next_statechange))
+ msleep(5);
+ ohci->next_statechange = jiffies;
+ omap_ohci_clock_power(1);
+ dev->dev.power.power_state = PMSG_ON;
+ usb_hcd_resume_root_hub(platform_get_drvdata(dev));
return 0;
}
+#endif
+
+/*-------------------------------------------------------------------------*/
+
/*
* Driver definition to register with the OMAP bus
*/
-static struct omap_driver ohci_hcd_omap_driver = {
- .drv = {
- .name = OMAP_OHCI_NAME,
- },
- .devid = OMAP_OCP_DEVID_USB,
- .busid = OMAP_BUS_OCP,
- .clocks = 0,
+static struct platform_driver ohci_hcd_omap_driver = {
.probe = ohci_hcd_omap_drv_probe,
.remove = ohci_hcd_omap_drv_remove,
-};
-
-/* Any dma_mask must be set for OHCI to work */
-static u64 omap_dmamask = 0xffffffffUL;
-
-/*
- * Device definition to match the driver above
- */
-static struct omap_dev ohci_hcd_omap_device = {
- .name = OMAP_OHCI_NAME,
- .devid = OMAP_OCP_DEVID_USB,
- .busid = OMAP_BUS_OCP,
- .mapbase = (void *)OMAP_OHCI_BASE,
- .dma_mask = &omap_dmamask, /* Needed only for OHCI */
- .res = {
- .start = OMAP_OHCI_BASE,
- .end = OMAP_OHCI_BASE + OMAP_OHCI_SIZE,
- },
- .irq = {
- INT_USB_HHC_1,
+ .shutdown = usb_hcd_platform_shutdown,
+#ifdef CONFIG_PM
+ .suspend = ohci_omap_suspend,
+ .resume = ohci_omap_resume,
+#endif
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "ohci",
},
};
static int __init ohci_hcd_omap_init (void)
{
- int ret;
-
- dbg (DRIVER_INFO " (OMAP)");
- dbg ("block sizes: ed %d td %d\n",
- sizeof (struct ed), sizeof (struct td));
-
- if (hmc_mode < 0 || hmc_mode > 25)
- hmc_mode = default_hmc_mode;
-
- /* Register the driver with OMAP bus */
- ret = omap_driver_register(&ohci_hcd_omap_driver);
- if (ret != 0)
+ printk (KERN_DEBUG "%s: " DRIVER_INFO " (OMAP)\n", hcd_name);
+ if (usb_disabled())
return -ENODEV;
- /* Register the device with OMAP bus */
- ret = omap_device_register(&ohci_hcd_omap_device);
- if (ret != 0) {
- omap_driver_unregister(&ohci_hcd_omap_driver);
- return -ENODEV;
- }
+ pr_debug("%s: block sizes: ed %Zd td %Zd\n", hcd_name,
+ sizeof (struct ed), sizeof (struct td));
- return ret;
+ return platform_driver_register(&ohci_hcd_omap_driver);
}
-MODULE_PARM(hmc_mode, "hmc_mode");
-
static void __exit ohci_hcd_omap_cleanup (void)
{
- omap_device_unregister(&ohci_hcd_omap_device);
- omap_driver_unregister(&ohci_hcd_omap_driver);
+ platform_driver_unregister(&ohci_hcd_omap_driver);
}
module_init (ohci_hcd_omap_init);
git://git.onelab.eu / linux-2.6.git / blobdiff