#define _USB_H_
#include <linux/usb.h>
+#include <linux/usb_usual.h>
#include <linux/blkdev.h>
#include <linux/smp_lock.h>
#include <linux/completion.h>
__u8 useProtocol;
__u8 useTransport;
int (*initFunction)(struct us_data *);
- unsigned int flags;
};
-/*
- * Static flag definitions. We use this roundabout technique so that the
- * proc_info() routine can automatically display a message for each flag.
- */
-#define US_DO_ALL_FLAGS \
- US_FLAG(SINGLE_LUN, 0x00000001) \
- /* allow access to only LUN 0 */ \
- US_FLAG(NEED_OVERRIDE, 0x00000002) \
- /* unusual_devs entry is necessary */ \
- US_FLAG(SCM_MULT_TARG, 0x00000004) \
- /* supports multiple targets */ \
- US_FLAG(FIX_INQUIRY, 0x00000008) \
- /* INQUIRY response needs faking */ \
- US_FLAG(FIX_CAPACITY, 0x00000010) \
- /* READ CAPACITY response too big */ \
- US_FLAG(IGNORE_RESIDUE, 0x00000020) \
- /* reported residue is wrong */ \
- US_FLAG(BULK32, 0x00000040) \
- /* Uses 32-byte CBW length */ \
- US_FLAG(NOT_LOCKABLE, 0x00000080) \
- /* PREVENT/ALLOW not supported */ \
- US_FLAG(GO_SLOW, 0x00000100) \
- /* Need delay after Command phase */ \
- US_FLAG(NO_WP_DETECT, 0x00000200) \
- /* Don't check for write-protect */ \
-
-#define US_FLAG(name, value) US_FL_##name = value ,
-enum { US_DO_ALL_FLAGS };
-#undef US_FLAG
/* Dynamic flag definitions: used in set_bit() etc. */
#define US_FLIDX_URB_ACTIVE 18 /* 0x00040000 current_urb is in use */
*/
#define US_IOBUF_SIZE 64 /* Size of the DMA-mapped I/O buffer */
+#define US_SENSE_SIZE 18 /* Size of the autosense data buffer */
typedef int (*trans_cmnd)(struct scsi_cmnd *, struct us_data*);
typedef int (*trans_reset)(struct us_data*);
typedef void (*proto_cmnd)(struct scsi_cmnd*, struct us_data*);
-typedef void (*extra_data_destructor)(void *); /* extra data destructor */
+typedef void (*extra_data_destructor)(void *); /* extra data destructor */
+typedef void (*pm_hook)(struct us_data *, int); /* power management hook */
+
+#define US_SUSPEND 0
+#define US_RESUME 1
/* we allocate one of these for every device that we remember */
struct us_data {
/* SCSI interfaces */
struct scsi_cmnd *srb; /* current srb */
-
- /* thread information */
- int pid; /* control thread */
+ unsigned int tag; /* current dCBWTag */
/* control and bulk communications data */
struct urb *current_urb; /* USB requests */
struct usb_ctrlrequest *cr; /* control requests */
struct usb_sg_request current_sg; /* scatter-gather req. */
unsigned char *iobuf; /* I/O buffer */
+ unsigned char *sensebuf; /* sense data buffer */
dma_addr_t cr_dma; /* buffer DMA addresses */
dma_addr_t iobuf_dma;
/* subdriver information */
void *extra; /* Any extra data */
extra_data_destructor extra_destructor;/* extra data destructor */
+#ifdef CONFIG_PM
+ pm_hook suspend_resume_hook;
+#endif
};
/* Convert between us_data and the corresponding Scsi_Host */