* linux/include/asm-arm/arch-omap/board-perseus2.h
*
* Copyright 2003 by Texas Instruments Incorporated
- * OMAP730 / P2-sample additions
- * Author: Jean Pihet
+ * OMAP730 / Perseus2 support by Jean Pihet
*
* Copyright (C) 2001 RidgeRun, Inc. (http://www.ridgerun.com)
* Author: RidgeRun, Inc.
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-#ifndef __ASM_ARCH_OMAP_P2SAMPLE_H
-#define __ASM_ARCH_OMAP_P2SAMPLE_H
+#ifndef __ASM_ARCH_OMAP_PERSEUS2_H
+#define __ASM_ARCH_OMAP_PERSEUS2_H
-#if defined(CONFIG_ARCH_OMAP730) && defined (CONFIG_MACH_OMAP_PERSEUS2)
-
-/*
- * NOTE: ALL DEFINITIONS IN THIS FILE NEED TO BE PREFIXED BY IDENTIFIER
- * P2SAMPLE_ since they are specific to the EVM and not the chip.
- */
-
-/* ---------------------------------------------------------------------------
- * OMAP730 Debug Board FPGA
- * ---------------------------------------------------------------------------
- */
-
-/* maps in the FPGA registers and the ETHR registers */
-#define OMAP730_FPGA_BASE 0xE8000000 /* VA */
-#define OMAP730_FPGA_SIZE SZ_4K /* SIZE */
-#define OMAP730_FPGA_START 0x04000000 /* PA */
-
-#define OMAP730_FPGA_ETHR_START OMAP730_FPGA_START
-#define OMAP730_FPGA_ETHR_BASE OMAP730_FPGA_BASE
-#define OMAP730_FPGA_FPGA_REV (OMAP730_FPGA_BASE + 0x10) /* FPGA Revision */
-#define OMAP730_FPGA_BOARD_REV (OMAP730_FPGA_BASE + 0x12) /* Board Revision */
-#define OMAP730_FPGA_GPIO (OMAP730_FPGA_BASE + 0x14) /* GPIO outputs */
-#define OMAP730_FPGA_LEDS (OMAP730_FPGA_BASE + 0x16) /* LEDs outputs */
-#define OMAP730_FPGA_MISC_INPUTS (OMAP730_FPGA_BASE + 0x18) /* Misc inputs */
-#define OMAP730_FPGA_LAN_STATUS (OMAP730_FPGA_BASE + 0x1A) /* LAN Status line */
-#define OMAP730_FPGA_LAN_RESET (OMAP730_FPGA_BASE + 0x1C) /* LAN Reset line */
-
-// LEDs definition on debug board (16 LEDs)
-#define OMAP730_FPGA_LED_CLAIMRELEASE (1 << 15)
-#define OMAP730_FPGA_LED_STARTSTOP (1 << 14)
-#define OMAP730_FPGA_LED_HALTED (1 << 13)
-#define OMAP730_FPGA_LED_IDLE (1 << 12)
-#define OMAP730_FPGA_LED_TIMER (1 << 11)
-// cpu0 load-meter LEDs
-#define OMAP730_FPGA_LOAD_METER (1 << 0) // A bit of fun on our board ...
-#define OMAP730_FPGA_LOAD_METER_SIZE 11
-#define OMAP730_FPGA_LOAD_METER_MASK ((1 << OMAP730_FPGA_LOAD_METER_SIZE) - 1)
+#include <asm/arch/fpga.h>
#ifndef OMAP_SDRAM_DEVICE
#define OMAP_SDRAM_DEVICE D256M_1X16_4B
#endif
-/*
- * These definitions define an area of FLASH set aside
- * for the use of MTD/JFFS2. This is the area of flash
- * that a JFFS2 filesystem will reside which is mounted
- * at boot with the "root=/dev/mtdblock/0 rw"
- * command line option.
- */
-
-/* Intel flash_0, partitioned as expected by rrload */
-#define OMAP_FLASH_0_BASE 0xD8000000 /* VA */
-#define OMAP_FLASH_0_START 0x00000000 /* PA */
-#define OMAP_FLASH_0_SIZE SZ_32M
-
-/* The Ethernet Controller IRQ is cascaded to MPU_EXT_nIRQ througb the FPGA */
-#define INT_ETHER INT_730_MPU_EXT_NIRQ
-
#define MAXIRQNUM IH_BOARD_BASE
#define MAXFIQNUM MAXIRQNUM
#define MAXSWINUM MAXIRQNUM
#define NR_IRQS (MAXIRQNUM + 1)
-#ifndef __ASSEMBLY__
-void fpga_write(unsigned char val, int reg);
-unsigned char fpga_read(int reg);
-#endif
-
-#else
-#error "Only OMAP730 Perseus2 supported!"
-#endif
-
#endif